Why My Ipad 1 cannot restore n update???
message show (The iPad "ipad" cannot restored at this time bcos the iPad spftware update server could not be contacted or temporarily unavailable. Please try again later.)
Please take note that the Original iPad can only be updated to IOS 5.1.1
Similar Messages
-
I can't upgrade from IOS 6.0.1 to IOS 7.1.1 on my iPad 2. iPad says it has downloaded IOS 7.0.3 but cannot verify the installation if I try and install it. It claims that I have lost internet connection, which I have not. I cannot restore or update the iPad in iTunes either, if I try to, I get an error message which says that I 'do not have permission to access the requested resource'. I am using the latest version of iTunes on Windows 8. I have tried putting the iPad in recovery mode and restoring it with iTunes, the result is the same.
Any help would be much appreciated.
Thanks!@Rudegar
Thanks for the reply, but I've been having this problem for well over a week. If it is a corrupt download, is there some way of deleting it from the iPad and getting a new one?
Thanks -
There must be a way. I cannot restore or update my 1st gen Ipad because it is locked with a passcode. help....
Connect in recovery mode and restore, you'll get the option to reset the passcode during this process:
iOS: Unable to update or restore and iPhone and iPod touch: Wrong passcode results in red disabled screen
If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software. -
I am having iPod classic 120GB Serial Number:8K913VF:2C7
I have tried a newer version of the iPod software is available (version 2.0.1). To update my iPod but it is showing error iPod : Cannot restore or update in iTunes with error 1415, 1417, 1418,1428,1429, 1430, 1436, or 1439.
How I can obtain suitable software for iPod classic 120GB Serial Number:8K913VF:2C7I have had this problem with Windows 7 and iTunes updates for some time. Each time it takes hours to solve but with the over the air upgrade to IOS6 on my iPhone and iPad, I was determined to solve and remember what I did, So here it is:
http://www.care4pcs.co.uk/2012/09/pear-shaped-apple-ios-6-for-iphone-ipad.html
I hope this helps you and any other users. -
TS1372 Cannot restore or update in iTunes with error 1437
Cannot restore or update in iTunes with error 1437
More info needed
Which version of iTunes are you using?
What is your iPod software version as shown on the iTunes Summary page?
Error 143x, normally caused by harddisk write timeout, probably due to
iPod Hardisk failing - Do the iPod Disk Diagnostic refer to this earlier tt2 post
Slow USB port, low datarate, due to sharing with other USB devices - Disconnect all other USB devices while Restoring or syncing. Dont use any USB hub and also use the USB port at the back of the PC. and not the front.
CPU Resource drained by other Apps like email, Antivirus, web broswer - Stop them, but if stopping Antivirus please disconnect the PC from the Inernet first.
Have a nice day! -
Cannot restore or update iPod in iTunes 7 or later????
Nano completely crashed today and said to restore with iTunes but i get this error "Error 1415, 1417, 1418, 1428, 1429, 1430, 1436 or 1439: Cannot restore or update iPod in iTunes 7 or later"
All the resolutions from this link http://support.apple.com/kb/TS1372 do not work
Anyone else have this issue?Am I just SOL?
-
I cannot restore or update my iphone
i cannot restore or update my iphone - message comes up 'the iphone could not be restored unknown error 1669 occured' I had just updated itunes before this but my iphone was saying - searching - and i could not make or recieve calls.please help!
http://support.apple.com/kb/ht1808
Also see this discussion: https://discussions.apple.com/message/23301940#23301940 -
TS3694 IPHONE 3G CANNOT RESTORE AND UPDATE ERROR CODE 1015
IPHONE 3G CANNOT RESTORE AND UPDATE ERROR CODE 1015
Unauthorized modification of iOS
http://support.apple.com/kb/HT3743
ERROR 1015...
This Error Code is indicative of the Device being jailbroken / Hacked...
Sorry... But...
The discussion of Jailbroken Devices is against the Terms of Use of this Forum.
You will need to look elsewhere. -
Why my iPad can't open app update (I open I see White scene)
Why my iPad can't open app update (can open App Store and I go to update I see White scene)
It seems Apple is having some issues at their end. There have been hundreds of posts on the forum with the same problem.
-
Ipad 2 wont restore after updating to ios 7
ipad 2 wont restore after updating to ios 7
Hello pinky03,
I would be be concerned too if I was not able to restore my iPad. If you have not resolved the issue, I recommend following the steps in this article for an issue like this:
iOS: Unable to update or restore
http://support.apple.com/kb/ht1808
Thank you for using Apple Support Communities.
Best,
Sheila M. -
HT201210 error 16, and cannot restore or update, plz help.
my update was stopped in the middle,
and next time i tried to restore and update, i cannot do any thing now,
the error code (16) apprear all the times,
my network, cable, windows, security, every thing is fine,
plz help.Hello, talatafaq.
Thank you for the question. Here is the article that provides the troubleshooting steps for error 16.
Check for hardware issues
Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the alert when you update or restore, contact Apple support.
Common errors: 1, 10-47, 1002, 1011, 1012, 1014, 1000-1020.
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
Regards,
Jason H. -
When choosing iCloud backup I choose the most recent backup but then after a few seconds it says "Cannot Restore Backup", what do I do?
its not possible to restore to a backup from a newer IOS
-
iPad 2 will not respond to iTunes recovery nor update now.
Try these instructions. Follow them exactly.
If you can't update or restore your iPhone, iPad, or iPod touch - Apple Support -
ITunes on pc can,t communicate with my iPad can,t restore or update
Going round in circles here and about to chuck iPad on the bin! I only discovered this problem when I tried to update my iPad via iTunes. Now not only can I not update or restore..... Same message each time update server could not be contacted, iTunes now cannot communicate with the iPad at all so I can,t read the contents or do anything at all with iPad.
I only have basic computer knowledge, but I am prepared to follow interactions if anyone can help.
Many thanks.messed around until something worked
-
I have updated to the lastest OS on my IPad3. No problem there. Then found I could no longer access my Itunes as there was a message 'Cannot be used as it requires version 10.6.3 or later. Go to ... and download'. I have tried four times and it won't work. I get another message saying I must sign in as administrator or contact my system administrator. I am the only one who uses this PC and have no idea what my administrator password is. Now I cannot use ITunes. Please help if you can. Thank you. Eileen Frost
Many thanks diesel. I cannot remember ever having an administrator password. Looks like I shall have to do a restore on my PC and not bother with the updates. Or maybe I could find my password from somewhere ? When I went into control panel I found a box with administrator and my name and it said password protected so I must have had one at some time. Any ideas on how I could find it ? Many thanks anyway. I always use a password to sign on but obviously that is not it. Eileen
Maybe you are looking for
-
How Can I replace an image and save the same size as the previous?
I want to replace an image in a PDF, but I would like to keep the same size, and location as the previous. I have tried to to it, but the new image takes a different size. This is a PDF exported from an InDesign template.
-
Reusing ADF Business components in a different installation
Hi, I have a customer who's interested in creating Business Components, packing them in a jar file, send that file to another location where some developers want to develop JSF pages using those BCs. I know this is posible in 11g, but can that be don
-
That about sums it up. I feel very unprofessional when it happens. Can I determine from within Thunderbird when it sends or doesn't send? How can I fix it? Is there a way to tell Thunderbird to prevent multiple identical emails? When it times out, it
-
Ultra Search Indexer: Adding 'alien' document types.
The way the Ultra Search indexer finds src material will not work in my situation. While I may be able to give it databases to crawl, it cannot crawl our content, so the way that you tell the indexer about 'alien' document types by adding custom code
-
How to "cleanse" source data in OWB
hi! I need cleanse source data like this: destination := NVL(source, 'not defined') in SQL select NVL(src_table.field, 'not defined') from src_table how I can it do in OWB?