Why my Mac Pro 2009 became too slow after updated Yosemite?

Why my Mac Pro 2009 became too slow after updated Yosemite?

When the slowness is especially bad, note the exact time: hour, minute, second.  
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
The title of the Console window should be All Messages. If it isn't, select
          SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar at the top of the screen.
Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above.
Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first.
Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting.

Similar Messages

  • My MacBook Pro (Retina, Mid 2012) is too slow after installing Yosemite version 10.10.1. All programs take for ever to load especially Safari and even chrome. I regret upgrading to yosemite, it was all fine with Maverick. Any suggestions ? ThankYou

    My MacBook Pro (Retina, Mid 2012) is too slow after installing Yosemite version 10.10.1. All programs take for ever to load especially Safari and even chrome. I regret upgrading to yosemite, it was all fine with Maverick. Any suggestions ? ThankYou

    1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
    Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
    2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
    There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
    3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
    You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
    In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
    You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
    Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
    4. Here's a summary of what you need to do, if you choose to proceed:
    ☞ Copy a line of text in this window to the Clipboard.
    ☞ Paste into the window of another application.
    ☞ Wait for the test to run. It usually takes a few minutes.
    ☞ Paste the results, which will have been copied automatically, back into a reply on this page.
    The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
    5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
    6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
    7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
    Triple-click anywhere in the line of text below on this page to select it:
    PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*genieo\* \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB ' com.adobe.AAM.Updater-1.0 com.adobe.AAM.Updater-1.0 com.adobe.AdobeCreativeCloud com.adobe.CS4ServiceManager com.adobe.CS5ServiceManager com.adobe.fpsaud com.adobe.SwitchBoard com.adobe.SwitchBoard com.apple.aelwriter com.apple.AirPortBaseStationAgent com.apple.FolderActions.enabled com.apple.installer.osmessagetracing com.apple.mrt.uiagent com.apple.ReportCrash.Self com.apple.rpmuxd com.apple.SafariNotificationAgent com.apple.usbmuxd com.citrixonline.GoToMeeting.G2MUpdate com.google.keystone.agent com.google.keystone.daemon com.microsoft.office.licensing.helper com.oracle.java.Helper-Tool com.oracle.java.JavaUpdateHelper com.oracle.java.JavaUpdateHelper org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.startx ' ' 879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 3694147963 1233118628 2456546649 2806998573 2778718105 2636415542 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 523110921 2883943871 3873345487 ' 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<10) print "com.apple.";} ' ' { sub(/ :/,"");print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { split("'"${p[41]}"'",b);split("'"${p[42]}"'",c);for(i in b) print b[i]".plist\t"c[i];if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\\([0-9]+\\)\\(.+\\)/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n   "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n   [N/A]";"cksum "F|getline C;split(C, A);C="checksum "A[1];"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F" ("T", "C")";else F=F" ("C")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n   ...and %s more line(s)\n",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */   /;' ' s/^.+ |\(.+\)$//g;p ' '/\.(appex|pluginkit)\/Contents\/Info\.plist$/p' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' pluginkit scutil dtrace profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil lsof test osascript\ -e );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$(RefProc): \$Message' -k Sender Req 'fsev|kern|launchd' -k RefProc Rne 'Aq|WebK' -k Message Rne 'Goog|ksadm|probe|Roame|SMC:|smcD|sserti|suhel| VALI|ver-r|xpma' -k Message Req 'abn|bad |Beac|caug|corru|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|NVDA\(|pagin|proc: t|Roamed|rror|SL|TCON|Throttli|tim(ed? ?|ing )o|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '/S*/*/Ca*/*xpc* >&- ||echo No' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,Ex}* {/,}L*/{A*d,Ca*/*/Ex,Co{mpon,reM},Ex,In{p,ter},iTu*/*P,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -path \\*s/Resources -prune -o -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????|wc -l' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' " -F '\$Time \$Message' -k Sender kernel -k Message CSeq 'n Cause: -' " );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents XPC\ cache Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors App\ extensions Lockfiles Memory\ pressure SMC Shutdowns );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};A'$((7+i))'() { v=` eval sudo "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};';done;A9(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "${s[63]}"<<<"$v"`&&C1 1 $1;};for i in 1 2 7 8;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;B1&&D73 19 53 67 55;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 54 12 56;D23 5 14 12 14;D22 6 36 13 15;D22 20 52 66 54;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D82 35 49 61 51;D82 11 17 17 20;for i in 0 1;do D82 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A8 18 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;B3 4 0 65;A3 14 6 32 0;B4 0 16 11;A1 26 50 64;B7 16;C3 52;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D73 21 0 32 19;D73 10 42 32 40;D82 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D12 22 20 32 25;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 21 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D83 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 10 42 32 41;D13 37 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 21 48 49 49;B3 4 22 57;A1 21 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D12 4 51 32 53;D23 22 9 37 7;A9;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
    Copy the selected text to the Clipboard by pressing the key combination command-C.
    8. Launch the built-in Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
    Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
    9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
    exec bash
    and press return. Then paste the script again.
    10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return  three times at the password prompt. Again, the script will still run.
    If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
    11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
    [Process completed]
    to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
    12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
    At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
    If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
    13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
    14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
    Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

  • Ipod touch 4th generation became too slow after ios 6. How can I rollback to iOS 5 or what else can be done. I already did  master reset and restored to factory default but no improvement.

    Ipod touch 4th generation became too slow after ios 6. How can I rollback to iOS 5 or what else can be done. I already did  master reset and restored to factory default but no improvement.

    You cannot downgrade

  • My MacBook Pro is running very slow after update to Yosemite

    My Macbook pro is running extremely slow after updating to Yosemite. What can I do to solve this problem?

    EtreCheck version: 2.1.1 (104)
    Report generated 8. dec. 2014 kl. 20.05.45 CET
    Hardware Information: ℹ️
      MacBook Pro (13-inch, Mid 2010) (Verified)
      MacBook Pro - model: MacBookPro7,1
      1 2.4 GHz Intel Core 2 Duo CPU: 2-core
      4 GB RAM Upgradeable
      BANK 0/DIMM0
      2 GB DDR3 1067 MHz ok
      BANK 1/DIMM0
      2 GB DDR3 1067 MHz ok
      Bluetooth: Old - Handoff/Airdrop2 not supported
      Wireless:  en1: 802.11 a/b/g/n
    Video Information: ℹ️
      NVIDIA GeForce 320M - VRAM: 256 MB
      Color LCD 1280 x 800
    System Software: ℹ️
      OS X 10.10.1 (14B25) - Uptime: 4:2:9
    Disk Information: ℹ️
      Hitachi HTS545025B9SA02 disk0 : (250,06 GB)
      S.M.A.R.T. Status: Verified
      EFI (disk0s1) <not mounted> : 210 MB
      Macintosh HD (disk0s2) / : 249.20 GB (195.10 GB free)
      Recovery HD (disk0s3) <not mounted>  [Recovery]: 650 MB
      MATSHITADVD-R   UJ-898 
    USB Information: ℹ️
      Apple Internal Memory Card Reader
      Apple Inc. Built-in iSight
      Apple Inc. BRCM2046 Hub
      Apple Inc. Bluetooth USB Host Controller
      Apple Computer, Inc. IR Receiver
      Apple Inc. Apple Internal Keyboard / Trackpad
    Gatekeeper: ℹ️
      Mac App Store and identified developers
    Launch Agents: ℹ️
      [loaded] com.oracle.java.Java-Updater.plist [Support]
    Launch Daemons: ℹ️
      [loaded] com.adobe.fpsaud.plist [Support]
      [loaded] com.macpaw.CleanMyMac2.Agent.plist [Support]
      [loaded] com.microsoft.office.licensing.helper.plist [Support]
      [loaded] com.oracle.java.Helper-Tool.plist [Support]
      [running] com.zeobit.MacKeeper.plugin.AntiTheft.daemon.plist [Support]
    User Launch Agents: ℹ️
      [running] com.spotify.webhelper.plist [Support]
      [invalid?] com.zeobit.MacKeeper.Helper.plist [Support]
    User Login Items: ℹ️
      iTunesHelper Program (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
      Dropbox Program (/Applications/Dropbox.app)
      Spotify Program (/Applications/Spotify.app)
    Internet Plug-ins: ℹ️
      FlashPlayer-10.6: Version: 15.0.0.239 - SDK 10.6 [Support]
      QuickTime Plugin: Version: 7.7.3
      AdobePDFViewerNPAPI: Version: 11.0.06 - SDK 10.6 [Support]
      AdobePDFViewer: Version: 11.0.06 - SDK 10.6 [Support]
      Flash Player: Version: 15.0.0.239 - SDK 10.6 [Support]
      Default Browser: Version: 600 - SDK 10.10
      SharePointBrowserPlugin: Version: 14.3.6 - SDK 10.6 [Support]
      ViewRightWebPlayer: Version: 2.3.0.4 [Support]
      Silverlight: Version: 5.1.20513.0 - SDK 10.6 [Support]
      JavaAppletPlugin: Version: Java 7 Update 55 Check version
    Safari Extensions: ℹ️
      Extensions: No such file or directory
    3rd Party Preference Panes: ℹ️
      Flash Player  [Support]
      Java  [Support]
    Time Machine: ℹ️
      Time Machine not configured!
    Top Processes by CPU: ℹ️
          13% mds
          11% WindowServer
          0% fontd
          0% AppleSpell
          0% Dropbox
    Top Processes by Memory: ℹ️
      228 MB com.apple.WebKit.WebContent
      193 MB Safari
      112 MB softwareupdated
      107 MB Microsoft Word
      94 MB Preview
    Virtual Memory Information: ℹ️
      617 MB Free RAM
      1.82 GB Active RAM
      869 MB Inactive RAM
      724 MB Wired RAM
      2.67 GB Page-ins
      74 KB Page-outs
    Diagnostics Information: ℹ️
      Dec 8, 2014, 04:04:13 PM Self test - passed

  • Mac Pro 2009 won't boot after airport installation

    Hey everyone, looking for some insight here.
    I recently bought a Mac Pro 2009 running Mavericks (at time of receipt). It didn't come with an airport card so I purchased one to install myself. The Mac was running fine until this evening when I finally got around to installing the card, however since then it won't get past the grey boot screen with apple logo. I've tried disconnecting the airport card to see if that reverted it, but no change. I also can't boot into safe mode, so that's no good. The only thing I can do is bring up the giant padlock with the option key held, which I saw elsewhere was connected with a firmware password (my admin doesn't work).
    Any advice here would be greatly appreciated. Thanks!

    It wouldn't be much of a lock if you could circumvent it with advice from a forum.
    Obviously a valid point, although possibly somewhat niaive where forums are concerned (no disrespect intended).
    It was more an expression of frustration than anything else, to be honest, though. It's kind of absurd that this happened following a simple hardware upgrade. Most people I know aren't even aware they can set a firmware password, so basically what it means is don't upgrade a machine that's intented to be upgraded (I'm aware of the hyperbole here).
    Looks like it will be a Mac store trip, though, yes. A pain in the arse since even my nearest authorised technician is miles away.

  • Response message became too slow, after transported to Consolidation Sys!

    Hi guys,
    I have a sync interface with BPM who calls an HTTP service.
    In development system things work fine and the interface is really fast. It gets a response from HTTP service in a few seconds (also with big messages, over 2 mega bytes). After transported to the consolidation system, the response message became too slow and after 600sec it gets a timeout.
    No parameters on Integration Server and RZ10 were changed…
    Anyone knows what’s happening or have an idea?
    Thanks in advance,
    Ricardo.
    Message was edited by: Ricardo  Quintino

    Hi Udo,
    What do you mean "the channels are not transported 1:1"?
    One thing, the difference between Development XI and Consolidation XI is that Consolidation is in Cluster.
    I need to do some extra configurations for HTTP in Cluster systems?
    Thanks in advance.
    Regards,
    Ricardo.
    Message was edited by: Ricardo  Quintino

  • Mac Pro 8-core too slow for Multiclip editing

    I have a Mac Pro 8core (pre-Nehalem), with 4 gb of memory. I'm doing some multiclip editing,and even with RT set to the lowest preview quality, my system stills blocks from time to time. I don't want to invest in a RAID-system, because I don't do multiclip editing that often. Is there an other - not expensive - way to speed up my Mac? Would adding memory - say to 6 gb - help?
    I also have the impression that since I upgraded to Leopard Snow, the computer is much less stable. FCP shut down twice unexpectedly yesterday.

    You don't say what format of HD you're editing but the fluidity of playing multiclip sequences is really dependent on the system's ability to provide all the streams of video in a timely manner. This means hard drive throughput is essential. A good quality sata drive in a MacPro can read somewhere around 115 MB/sec when empty. It will spool material less effectively as it fills.
    Very good quality esata RAID systems can provide 5x that - which is why people utilize them. (fwiw-I've run 16 streams of 720p24 DVCProHD off of a Caldigit HDOne in a multiclip sequence without a hiccup. )
    What can you do if you don't want to pay the price for the right gear for the job?
    1. populate all your internal bays with fast hard drives
    2. empty the drives
    3. spread your captured files across all three (non system drives)
    This will distribute the load as much as possible without going to a RAID setup.
    Once you have all the drives empty, you could try setting up a RAID 0 set using Disk Utility and see if that works for you. One caveat - if you decide to go the internal software RAID 0 route, recognize there is no failsafe should you encounter a serious system crash. Everything on all drives that are part of the RAID set can be compromised.
    Good luck,
    x

  • Mac Pro 2009 Raid Set Lost after Hard Reboot

    We have a newer Nehalem based Mac Pro with a 2009 Black Apple Hardware Raid card.  The Hard Drive Configuration is: 4 x 2TB Western Digital drives setup as a Raid 1+0 array providing 4TB of space with what we believed to be optimal performance and redundancy.  We had two volumes / partitions configured on the array, one 120GB for the OS and the remaining 3.8TB for data. 
    Everything was working fine when the server froze up.  ON the Screen an error message said there is a problem with your Raid controller, Please open Apple Raid Utility.. Unfortunatly when we tried to do that we just got a spining beachball. We tried to open finder and it beachballed.  We tried to force quit and nothing working. Finally we were left with no choice but to do a hard restart of the server and turn the machine off and then back on. 
    When the server came back on it would not boot up.  We were greeting with the Folder with a Queston Mark.  We booted from the Mac 10.6 Snow leopard Server Disk and opened up Apples Raid utility software.  Much to our shock the Raid Set and the two Volumes were not shown in the Utility.  However all 4 of the drives were listed and all being shown as Green light good status, but listed as "Roaming".  We weren't sure what to do, the volumes weren't accesible since they didn't exist, the Raid set wasn't there, there was no way to run something like Data Rescue Recovery software.  We tried calling Apple and have to wait until they open this morning.  After looking online at various forums we came accross this problem with no solutions.  Most of the people with the problems had the older 2006 Blue Raid card, and this appeared to be a common issue amoung others with the older card.  I decided to try and re-create the Raid 1+0 set.  However as soon as I did that I was prompted by Raid Utility that the drives I was selecting to use for the Raid set were already a part of another raid set and using them would delete the data on the set.  I obviously canceled the process. Crazy enough the system knows the drives belong to a Raid set but doesn't realize it should know what the raid set information is.
    We were using Mac OS 10.6.7 Snow Leopard Server, and I even tried installing and updating an external drive with 10.6.7 Server and booted from the drive from the machine and try to run Raid Utility.  That did not work either.  Any advice from anyone would be awesome.  I'm worried what Apple is going to say when I do get a hold of them, the system is under Apple Care warranty.  Thanks in advance for anyone's time.

    I haven't lost data, but in my 2010 Mac Pro with 2009-vintage Apple RAID card, it has this Really Annoying Habit of constantly losing Disk 3 (the spare) in my 4x2 TB internal RAID5 array whenever I have to do a hard reboot.
    I keep having to re-mark the now-"Roaming" drive as a Spare and then wait 8+ hours for it to rebuild the array ... grrr.
    I saw an Apple KB article that suggests removing the Roaming disk and re-inserting it.  Duh.  Fat lot of good that did.  Really wish there was some answer to this issue ... hard reboots should NOT cause array disks to go from "Assigned"/good to "Roaming"! 

  • HT1688 Why is My iPhone 4 is extremely slow after updated to ios7

    My Iphone 4 is basically impossible to use after updating it to ios7.  When I type a text message I have timed it taking up to 45 seconds before any letters show up.  It also is very slow if I am typing in safari for a website.

    I did too.  I went to Settings > iCloud > Documents and Data, then turned off  documents and data, and now it is back to normal.  Apparently you cannot take advantage of both on the iphone 4 and 4s.

  • My iPad became so slow after updating it to IOS 6... It happened to someone too? What should i do about it?

    Everything is so slow!!! In ios 6 my iPad used to be fast before this update... And youtube doesn't work on the safari.. It asks for flash player... Those problems weren't exict if Steve Was here... 

    AFAIK, downloading directly to the device is typically smaller as it only gets the stuff it needs for your specific device as oposed to the  full download  when downloading from iTunes.
    Correct, no Siri for iTouch 4th gen.
    The Maps app is there, but I moved it around, so I'm not sure where it is on your device, but its in there.
    Safari is updated in iOS 6, your other apps should update in the App Store when their developers release updates, I've launched only a few apps so far, no problems with compatibility!

  • My Macbook Pro (purchased in mid 2009) runs really slow after updated the software.

    How can I get it to run faster?

    Find out what it is doing:
    Runaway applications can shorten battery runtime, affect performance, and increase heat and fan activity
    anything using double-digits is suspect.

  • MacBook Pro has been running slow after installing Yosemite

    Hey,
    I have a MacBook Pro and recently updated from OS 10.6.8 to Yosemite. My computer has been running really slow lately.
    Here is my EtreCheck Report:
    Problem description:
    Mac has been running very slowly
    EtreCheck version: 2.1.6 (109)
    Report generated January 18, 2015 at 10:42:01 PM EST
    Download EtreCheck from http://etresoft.com/etrecheck
    Click the [Support] links for help with non-Apple products.
    Click the [Details] links for more information about that line.
    Click the [Adware] links for help removing adware.
    Hardware Information: ℹ️
      MacBook Pro (13-inch, Mid 2010) (Technical Specifications)
      MacBook Pro - model: MacBookPro7,1
      1 2.4 GHz Intel Core 2 Duo CPU: 2-core
      4 GB RAM Upgradeable
      BANK 0/DIMM0
      2 GB DDR3 1067 MHz ok
      BANK 1/DIMM0
      2 GB DDR3 1067 MHz ok
      Bluetooth: Old - Handoff/Airdrop2 not supported
      Wireless:  en1: 802.11 a/b/g/n
      Battery Health: Normal - Cycle count 989
    Video Information: ℹ️
      NVIDIA GeForce 320M - VRAM: 256 MB
      Color LCD 1280 x 800
    System Software: ℹ️
      OS X 10.10.1 (14B25) - Time since boot: 2:48:14
    Disk Information: ℹ️
      Hitachi HTS545025B9SA02 disk0 : (250.06 GB)
      EFI (disk0s1) <not mounted> : 210 MB
      Macintosh HD (disk0s2) / : 249.20 GB (78.83 GB free)
      Recovery HD (disk0s3) <not mounted>  [Recovery]: 650 MB
      MATSHITADVD-R   UJ-898 
    USB Information: ℹ️
      Apple Inc. Built-in iSight
      Apple Internal Memory Card Reader
      Apple Inc. BRCM2046 Hub
      Apple Inc. Bluetooth USB Host Controller
      Apple Computer, Inc. IR Receiver
      Apple Inc. Apple Internal Keyboard / Trackpad
    Gatekeeper: ℹ️
      Mac App Store and identified developers
    Launch Daemons: ℹ️
      [not loaded] org.eyebeam.SelfControl.plist [Support]
    User Launch Agents: ℹ️
      [loaded] com.divx.agent.postinstall.plist [Support]
      [failed] com.facebook.videochat.[redacted].plist [Support]
      [loaded] com.google.keystone.agent.plist [Support]
    User Login Items: ℹ️
      iTunesHelper UNKNOWN Hidden (missing value)
      Spotify UNKNOWN  (missing value)
      uTorrent Application  (/Applications/uTorrent.app)
    Internet Plug-ins: ℹ️
      FlashPlayer-10.6: Version: 11.1.102.55 [Support]
      OVSHelper: Version: 1.0 [Support]
      Flash Player: Version: 11.1.102.55 Mismatch! Adobe recommends 16.0.0.257
      QuickTime Plugin: Version: 7.7.3
      DivXBrowserPlugin: Version: 2.2 [Support]
      Default Browser: Version: 600 - SDK 10.10
      Silverlight: Version: 4.0.51204.0 [Support]
      iPhotoPhotocast: Version: 7.0
    Safari Extensions: ℹ️
      Searchme [Installed] Adware! [Remove]
      DivX Plus Web Player HTML5 <video> [Installed]
    3rd Party Preference Panes: ℹ️
      DivX  [Support]
      Flash Player  [Support]
      MacFUSE  [Support]
      Perian  [Support]
    Time Machine: ℹ️
      Time Machine not configured!
    Top Processes by CPU: ℹ️
          24% Google Chrome
          12% WindowServer
          4% coreaudiod
          3% Google Chrome Helper EH
          2% hidd
    Top Processes by Memory: ℹ️
      279 MB Google Chrome Helper EH
      176 MB Finder
      150 MB Google Chrome
      77 MB WindowServer
      69 MB Pages
    Virtual Memory Information: ℹ️
      171 MB Free RAM
      1.28 GB Active RAM
      1.14 GB Inactive RAM
      821 MB Wired RAM
      4.60 GB Page-ins
      135 MB Page-outs
    Diagnostics Information: ℹ️
      Jan 18, 2015, 07:54:30 PM Self test - passed
      Jan 18, 2015, 06:51:08 PM /Users/[redacted]/Library/Logs/DiagnosticReports/Photo Booth_2015-01-18-185108_[redacted].crash

    Back up your Mac, if you have not already done so. To learn how to do that read Mac Basics: Time Machine backs up your Mac.
    You inadvertently installed adware. Eradicating it is simple and you don't have to download or install anything to fix it. For an explanation or how this may have occurred, how to avoid it in the future, and for Apple's recommended solution read How to install adware.
    Google Chrome is known to run notoriously poorly on Macs. If you want to run Google Chrome, you may need to install more memory, upgrade your Mac to a newer model, or both. Use Safari or Firefox, both of which will run well and do not litter a system with a plethora of resource - hungry "helpers" and other constantly running intrusive processes such as those Google insists upon installing.
    Adobe Flash Player is outdated. If you need to use Adobe Flash Player, you must keep it up to date. New versions appear very frequently.
    You are running a torrent client. Doing so will leave you vulnerable to malware, data theft, or both.
    Some users have resolved otherwise inexplicably poor performance with an SMC reset. Read and follow all the steps including those that may appear to be inapplicable or trivial.
    If your Mac still performs poorly, please determine if the same problems also occur in "Safe Mode":
    Safe Mode or "Safe Boot" is a troubleshooting mode that bypasses all third party system extensions and loads only required system components. Read about it: Starting up in Safe Mode
    You must disable FileVault before you can start your Mac in Safe Mode.
    Starting your Mac in Safe Mode will take longer than usual, graphics will not render smoothly, audio is disabled on some Macs, and some programs (iTunes for example) may not work at all.
    Merely starting your Mac in Safe Mode is not intended to resolve the problem, it's to observe its performance without certain additional components.
    To end Safe Mode restart your Mac normally. Shutdown will take longer as well.
    If none of the above resolves your concern, more information is required. To augment the information you already provided, follow the instructions below.
    If your Mac is momentarily unresponsive, consider the following.
    Launch the Console app - it is in your Utilities folder. You can find it by selecting Utilities from the Finder's Go menu.
    If the log list column on the left is not already displayed, show the log list by selecting Show Log List from Console's View menu. Select Show Toolbar if it is not already shown.
    Locate system.log in the list and select it. Many date and time-stamped entries will appear, hundreds of them, and you must find the entries relevant to your Mac's problem.
    To do that click the Clear Display button in the Toolbar. All previously displayed log entries will be disappear.
    Next: Perform whatever actions cause the Mac to exhibit the slow behavior. If the problem is caused by errors logged by the system, the Console window will show them being recorded in system.log.
    One or more of them, along with their time stamps, may reveal the reason for the problem you describe.
    Copy and paste those log entries in a reply. If hundreds of the same repetitive messages appear, please edit them before posting. There should be no need for more than a few log entries.
    Most of the entries will be cryptic but will contain information you might consider personal such as your Mac's name. If you do not want that information to appear, delete or obscure it when posting your reply. Leave enough information so that the entries can be deciphered.

  • Why Weather App locate my location so slow after updated iOS 5.1?

    The weather app update my location so slow than it does in iOS5.0.1. And sometime it automatically use location service , and it occuerred so often that I have to close the weather opinion in the location service, what's wrong with iOS 5.1?

    The weather app update my location so slow than it does in iOS5.0.1. And sometime it automatically use location service , and it occuerred so often that I have to close the weather opinion in the location service, what's wrong with iOS 5.1?

  • Why is my mac mini running slow after downloading Yosemite?

    My mac mini is running significantly slower after downloading Yosemite and I am wondering if it is to better to try to go back to an older operating system or if Apple is working on a fix for this.
    Here is what I am Running it on:
    Model Name: Mac mModel Identifier: Macmini3,1
                                        Processor Name Processor Name: Intel Core 2 Duo
                                       Processor Speed: 2.26 GHz
                                        Number of Processors: 1
                                        Total Number of Cores: 2
                                           L2 Cache: 3 MB
                                            Memory: 2 GB
                                            Bus Speed: 1.07 GHz
                                           Boot ROM Version: MM31.00AD.B00
                                            SMC Version (system): 1.35f1
                                               Hardware UUID: 2DF68C91-A8F8-536A-87EF-14DDEF6FAB32

    I thought I had gotten rid of the HP shortcut manager and can no longer find it but when I re ran my Test it is still there. Were could it be hiding that I can not find it now?
    EtreCheck version: 2.0.10 (97)
    Report generated November 1, 2014 at 10:39:40 PM CDT
    Hardware Information: ℹ️
      Mac mini (Late 2009) (Verified)
      Mac mini - model: Macmini3,1
      1 2.26 GHz Intel Core 2 Duo CPU: 2-core
      2 GB RAM Upgradeable
      BANK 0/DIMM0
      1 GB DDR3 1067 MHz ok
      BANK 1/DIMM0
      1 GB DDR3 1067 MHz ok
      Bluetooth: Old - Handoff/Airdrop2 not supported
      Wireless:  en1: 802.11 a/b/g/n
    Video Information: ℹ️
      NVIDIA GeForce 9400 - VRAM: 256 MB
      Panasonic-TV spdisplays_720p
    System Software: ℹ️
      OS X 10.10 (14A389) - Uptime: 3 days 6:35:47
    Disk Information: ℹ️
      FUJITSU MHZ2160BH G1 disk0 : (160.04 GB)
      S.M.A.R.T. Status: Verified
      EFI (disk0s1) <not mounted> : 210 MB
      Macintosh HD (disk0s2) /  [Startup]: 159.18 GB (71.82 GB free)
      Recovery HD (disk0s3) <not mounted>  [Recovery]: 650 MB
      OPTIARC DVD RW AD-5670S 
    USB Information: ℹ️
      Sunplus Technology Co.,Ltd. USB to Serial-ATA bridge 1 TB
      S.M.A.R.T. Status: Verified
      EFI (disk2s1) <not mounted> : 210 MB
      ROCSTAR BACKUP (disk2s2) /Volumes/ROCSTAR BACKUP : 999.86 GB (848.90 GB free)
      Eastman Kodak Company ESP Office 6100 Series AiO
      Apple Inc. BRCM2046 Hub
      Apple Inc. Bluetooth USB Host Controller
      Apple Computer, Inc. IR Receiver
    Firewire Information: ℹ️
      0x30F0 ATA Device 00 800mbit - 800mbit max
      S.M.A.R.T. Status: Verified
      EFI (disk1s1) <not mounted> : 210 MB
      Time Machine (disk1s2) /Volumes/Time Machine : 145.52 GB (42.09 GB free)
      Main Drive 2 (disk1s3) /Volumes/Main Drive 2 : 854.21 GB (699.03 GB free)
    Gatekeeper: ℹ️
      Mac App Store and identified developers
    Problem System Launch Agents: ℹ️
      [failed] com.apple.CallHistoryPluginHelper.plist
      [failed] com.apple.CallHistorySyncHelper.plist
      [failed] com.apple.cmfsyncagent.plist
      [failed] com.apple.coreservices.appleid.authentication.plist
      [failed] com.apple.EscrowSecurityAlert.plist
      [failed] com.apple.sbd.plist
      [failed] com.apple.scopedbookmarkagent.xpc.plist
      [failed] com.apple.telephonyutilities.callservicesd.plist
    Problem System Launch Daemons: ℹ️
      [failed] com.apple.AssetCacheLocatorService.plist
      [failed] com.apple.awdd.plist
      [failed] com.apple.ctkd.plist
      [failed] com.apple.diagnosticd.plist
      [failed] com.apple.icloud.findmydeviced.plist
      [failed] com.apple.ifdreader.plist
      [failed] com.apple.installd.plist
      [failed] com.apple.nehelper.plist
      [failed] com.apple.periodic-daily.plist
      [failed] com.apple.periodic-weekly.plist
      [failed] com.apple.softwareupdate_download_service.plist
      [failed] com.apple.softwareupdated.plist
      [failed] com.apple.tccd.system.plist
      [failed] com.apple.wdhelper.plist
    Launch Agents: ℹ️
      [loaded] com.coupons.coupond.plist Support
      [loaded] com.hp.help.tocgenerator.plist Support
      [running] com.kodak.BonjourAgent.plist Support
      [loaded] com.oracle.java.Java-Updater.plist Support
    Launch Daemons: ℹ️
      [loaded] com.adobe.fpsaud.plist Support
      [running] com.backblaze.bzserv.plist Support
      [running] com.google.keystone.daemon.plist Support
      [loaded] com.oracle.java.Helper-Tool.plist Support
      [loaded] com.oracle.java.JavaUpdateHelper.plist Support
    User Launch Agents: ℹ️
      [running] com.backblaze.bzbmenu.plist Support
      [invalid?] com.google.GoogleContactSyncAgent.plist Support
      [loaded] com.kodak.KODAK AiO Firmware Updater.plist Support
      [loaded] com.kodak.KODAK AiO Software Updater.plist Support
      [running] com.kodak.StatisticCollection.plist Support
    User Login Items: ℹ️
      iTunesHelper UNKNOWNHidden (missing value)
      HPShortcutManager Application (/Library/Application Support/Hewlett-Packard/HP Scanjet Scanner/HPShortcutManager.app)
      Google Chrome ApplicationHidden (/Users/[redacted]/Desktop/Google Chrome.app)
      Alfred Application (/Applications/Alfred.app)
      Printer Pro Desktop Application (/Applications/Printer Pro Desktop.app)
      Google Software Update Application (/Library/Google/GoogleSoftwareUpdate/GoogleSoftwareUpdate.bundle/Contents/Reso urces/GoogleSoftwareUpdateAgent.app)
      HPShortcutManager Application (/Library/Application Support/Hewlett-Packard/HP Scanjet Scanner/HPShortcutManager.app)
      HPShortcutManagerStartup Application (/Library/Application Support/Hewlett-Packard/HP Scanjet Scanner/HPShortcutManagerStartup.app)
      HP Scheduler Application (/Library/Application Support/Hewlett-Packard/Software Update/HP Scheduler.app)
    Internet Plug-ins: ℹ️
      DirectorShockwave: Version: 11.5.9r620 Support
      Default Browser: Version: 600 - SDK 10.10
      Flip4Mac WMV Plugin: Version: 3.2.0.16   - SDK 10.8 Support
      Google Earth Plugin: Version: 5.1 Support
      RealPlayer Plugin: Version: (null) Support
      Silverlight: Version: 5.1.30514.0 - SDK 10.6 Support
      FlashPlayer-10.6: Version: 15.0.0.189 - SDK 10.6 Support
      Flash Player: Version: 15.0.0.189 - SDK 10.6 Support
      QuickTime Plugin: Version: 7.7.3
      iPhotoPhotocast: Version: 7.0
      AdobePDFViewer: Version: Unknown
      CouponPrinter-FireFox_v2: Version: 5.0.3 - SDK 10.6 Support
      Photo Center Plugin: Version: Photo Center Plugin 1.1.2.2 Support
      JavaAppletPlugin: Version: Java 7 Update 71 Check version
    User Internet Plug-ins: ℹ️
      Move_Media_Player: Version: npmnqmp 07103007 Support
      fbplugin_1_0_1: Version: (null) Support
      fbplugin_1_0_3: Version: (null) Support
    3rd Party Preference Panes: ℹ️
      Backblaze Backup  Support
      Flash Player  Support
      Flip4Mac WMV  Support
      Java  Support
    Time Machine: ℹ️
      Skip System Files: NO
      Mobile backups: OFF
      Auto backup: NO - Auto backup turned off
      Volumes being backed up:
      Macintosh HD: Disk size: 159.18 GB Disk used: 87.36 GB
      Destinations:
      Main Drive [Local]
      Total size: 999.86 GB
      Total number of backups: 2
      Oldest backup: 2013-04-03 01:58:20 +0000
      Last backup: 2013-05-15 17:53:48 +0000
      Size of backup disk: Excellent
      Backup size 999.86 GB > (Disk size 159.18 GB X 3)
    Top Processes by CPU: ℹ️
          99% HPShortcutManager
          7% WindowServer
          0% coreduetd
          0% bzserv
          0% AppleSpell
    Top Processes by Memory: ℹ️
      60 MB Mail
      34 MB WindowServer
      28 MB Google Chrome
      28 MB Safari
      26 MB mds
    Virtual Memory Information: ℹ️
      116 MB Free RAM
      360 MB Active RAM
      362 MB Inactive RAM
      514 MB Wired RAM
      82.08 GB Page-ins
      1.99 GB Page-outs

  • Why my Mac Pro hard drive noise and too slow?

    Why my Mac Pro hard drive noise and too slow? Totally 8 gb speed system but now very slow . Please give some suggestions

    Another thing you can do in Lion (and ML) is click on the "Info" button in Disk Utility to get the SMART status of the drive.It's more detailed now than it used to be and it might tell you if something is wrong.
    A lot can go wrong with a hard drive which is why I tend to point people to the downloads section of the following web site:
    http://scsc-online.com
    They have a free hard drive troublleshooting download book there. I reccommend people download that before asking questionis because there are tons of problems that can act like hard drive problems when there's nothing wrong with the system at all. For example, how full is the drive? How many applications are running? What's the status of Spotlight indexing? How many apps are you running? How much memory do you have?
    I could probably think up 20 or 30 more if needed.

Maybe you are looking for

  • How do I use find my iPhone with a iPod Touch 3g?

    l I tried using it on  a friends iPod Touch, because I lost mine. I tried regestring but It didn't work, to my dismay I learned that MobileMe was closed to new subscribers. I tried doing it on iCloud, but iCloud is only for iOS 5. So how do I registe

  • Accounting Clerk not extended to SAP Connect (SOST) with fax

    Hi, Hope you can help me with my below issue. I am sending payment advice notes with program: RFFOEDI1 and RFFOUS_T through transaction F110...I am happy with the payment advice note we send with e-mail and it works fine because it does extend Accoun

  • Not everyone is having maps issues

    I know and acknowledge that there are users in some areas being extremely vocal about thier dislike of the new Maps in iOS6. But not all of the users are having problems. I used the new Maps feature last weekend to get to a new bar in Granite City, I

  • Value date while posting from FRFT_B

    Hi When I am posting from FRFT_B (Bank to Bank transfer) value is date is displaying in this transaction(FRFT_B) but when we posted document , value date is not updating in FI document hence we are not able to see value date. Can some one hlpe is the

  • Boot Camp can't create a Windows partition

    Hello, I'm trying to create a new partition to install Windows 7 on, but I am unable to do so. At first I tried to do this with Boot Camp Assistant, but it didn't work. Then I tried to create a FAT partition with Disk Utility, which didn't work eithe