Why the Fibre uplink ports are down state even after giving no shutdown command at the interface

Hi
My Predecessors brought 2 CISCO 3750 switches and implemented LACP on these core switches. Due to looping in the network the Fibre uplink ports GigabitEthernet1/1/3 and GigabitEthernet2/1/3 are down (I think these uplink ports are mirrored in the LACP concept)
Please see below from the configuration.
I logged into the core switch and went to this particular interface GigabitEthernet1/1/3 and I gave the following command and still the port is in the down state after I gave no shutdown command. Do I need to give the same no shutdown command at interface GigabitEthernet2/1/3 as well ?
Switch-Core1(config) interface GigabitEthernet1/1/3
Switch-Core1(config-if)#no shutdown
Switch-Core1(config-if)#
Please see below After no shutdown command given still these 2 Gigabit fibre uplink ports are down.
GigabitEthernet1/0/20 unassigned YES unset up up
GigabitEthernet1/0/21 unassigned YES unset down down
GigabitEthernet1/0/22 unassigned YES unset down down
GigabitEthernet1/0/23 unassigned YES unset down down
GigabitEthernet1/0/24 unassigned YES unset up up
GigabitEthernet1/1/1 unassigned YES unset up up
GigabitEthernet1/1/2 unassigned YES unset up up
GigabitEthernet1/1/3 unassigned YES unset down down
GigabitEthernet1/1/4 unassigned YES unset up up
Te1/1/1 unassigned YES unset down down
Te1/1/2 unassigned YES unset down down
GigabitEthernet2/0/1 unassigned YES unset up up
GigabitEthernet2/0/2 unassigned YES unset up up
GigabitEthernet2/0/3 unassigned YES unset up up
GigabitEthernet2/0/4 unassigned YES unset down down
GigabitEthernet2/0/5 unassigned YES unset up up
GigabitEthernet2/0/6 unassigned YES unset down down
GigabitEthernet2/0/7 unassigned YES unset down down
GigabitEthernet2/0/8 unassigned YES unset up up
GigabitEthernet2/0/9 unassigned YES unset up up
GigabitEthernet2/0/10 unassigned YES unset down down
GigabitEthernet2/0/11 unassigned YES unset down down
GigabitEthernet2/0/12 unassigned YES unset down down
GigabitEthernet2/0/13 unassigned YES unset down down
GigabitEthernet2/0/14 unassigned YES unset up up
GigabitEthernet2/0/15 unassigned YES unset up up
GigabitEthernet2/0/16 unassigned YES unset up up
GigabitEthernet2/0/17 unassigned YES unset up up
GigabitEthernet2/0/18 unassigned YES unset up up
GigabitEthernet2/0/19 unassigned YES unset down down
GigabitEthernet2/0/20 unassigned YES unset up up
GigabitEthernet2/0/21 unassigned YES unset down down
GigabitEthernet2/0/22 unassigned YES unset up up
GigabitEthernet2/0/23 unassigned YES unset down down
GigabitEthernet2/0/24 unassigned YES unset up up
GigabitEthernet2/1/1 unassigned YES unset up up
GigabitEthernet2/1/2 unassigned YES unset up up
GigabitEthernet2/1/3 unassigned YES unset down down
GigabitEthernet2/1/4 unassigned YES unset up up
Te2/1/1 unassigned YES unset down down
Te2/1/2 unassigned YES unset down down
Port-channel1 unassigned YES unset down down
Port-channel2 unassigned YES unset down down
Please let me know if I am doing something wrong .Please post me some tutorial to sort this.

It is possible you are overloading that little 4215. If that is the case you should also be seeing "missed packet percentage" messages in your events.
How much traffic is your 4215 getting? Those sensors will start to drop packets for inspection at about 30 Mb/s.
- Bob

Similar Messages

The g, h and backspace on my keyboard are not working even after replacing with a new one.

The g, h and backspace on my keyboard are not working even after replacing with a new one. I have also updated my BIOS still d same. Please help me ASAP.
...am waiting for a QIUCK RESPONSE

How does a usb keyboard attached externally work?
You might try a "hard reset" where you remove battery and AC charger, hold down power button 20-30 seconds and then reassemble and turn on. Reset BIOS (F10) to default settings, too.

Elements 10, windows 8, 64 bit, epson artisan 835 printer: prints are really dark even after using enhancements like adjusting lighting. Prints are darker than photoshop edit screen. Prints are acceptable using paint, windows photo viewer, or gallery.

Elements 10, Windows 8, 64 bit, Epson Artisan 835 printer: Prints are really dark even after applying enhancements, like adjusting lighting. Prints are darker than Photoshop Edit Screen. Prints are acceptable using Paint, Windows Photoviewer, or Photo Gallery.

In general theory, one now has the Edit button for their posts, until someone/anyone Replies to it. I've had Edit available for weeks, as opposed to the old forum's ~ 30 mins.
That, however, is in theory. I've posted, and immediately seen something that needed editing, only to find NO Replies, yet the Edit button is no longer available, only seconds later. Still, in that same thread, I'd have the Edit button from older posts, to which there had also been no Replies even after several days/weeks. Found one that had to be over a month old, and Edit was still there.
Do not know the why/how of this behavior. At first, I thought that maybe there WAS a Reply, that "ate" my Edit button, but had not Refreshed on my screen. Refresh still showed no Replies, just no Edit either. In those cases, I just Reply and mention the [Edit].
Also, it seems that the buttons get very scrambled at times, and Refresh does not always clear that up. I end up clicking where I "think" the right button should be and hope for the best. Seems that when the buttons do bunch up they can appear at random around the page, often three atop one another, and maybe one way the heck out in left-field.
While I'm on a role, it would be nice to be able to switch between Flattened and Threaded Views on the fly. Each has a use, and having to go to Options and then come back down to the thread is a very slow process. Jive is probably incapable of this, but I can dream.
Hunt

Why can't I use effects on camera even after I upgraded to 5.1?

Why can't I use effects on camera even after I upgraded to 5.1?

What effects are you referring to?

All iPad buttons are not working even after resetting it (hard, soft and via iTunes).

All iPad 2 buttons are not working even after I resetting it. I tried both of the hard and soft reset, and even resetting my iPad via iTunes.
The volume buttons work after I tried this method : "hold iPad in landscape mode. Push the home button while rotating it to Portrait mode, release it."

I have the same issue, nothing I did fixed the problem, I would suggest if you can visit apple store and give us your feedback with them.
for me I can't go to apple store because I don't have any store near me, I will have to wait for 2 months to travel!

Why is my iphone 4 not turning on, even after hours of charge?

Why is my iphone 4 not turning on even after hours of charge?

Try holding both the home and power buttons at the same time until the Apple boot logo appears. If it doesn't appear after 15 seconds, this probably won't work.

Nexus 2232 TM uplink ports are they only for uplink use?

We have upgraded our N5K to support the new 2232TM, but now we face the issue that the 8 SFP+ ports are not visible in our config:
Nexus5010_1# sh fex 103 det
FEX: 103 Description: 2KSRV02   state: Online
FEX version: 5.0(3)N2(2a) [Switch version: 5.0(3)N2(2a)]
FEX Interim version: 5.0(3)N2(2a)
Switch Interim version: 5.0(3)N2(2a)
Extender Model: N2K-C2232TM-10GE, Extender Serial: FOC15262P7Q
Part No: 73-13626-03
Card Id: 164, Mac Addr: 30:e4:db:66:12:02, Num Macs: 64
Module Sw Gen: 21 [Switch Sw Gen: 21]
post level: complete
pinning-mode: static    Max-links: 1
Fabric port for control traffic: Eth1/9
Fabric interface state:
    Po103 - Interface Up. State: Active
    Eth1/9 - Interface Up. State: Active
    Eth1/10 - Interface Up. State: Active
Fex Port        State Fabric Port
       Eth103/1/1 Down       Po103
       Eth103/1/2 Down       Po103
       Eth103/1/3 Down       Po103
       Eth103/1/4 Down       Po103
       Eth103/1/5 Down       Po103
       Eth103/1/6 Down       Po103
       Eth103/1/7 Down       Po103
       Eth103/1/8 Down       Po103
       Eth103/1/9 Down       Po103
      Eth103/1/10 Down       Po103
      Eth103/1/11 Down       Po103
      Eth103/1/12 Down       Po103
      Eth103/1/13 Down       Po103
      Eth103/1/14 Down       Po103
      Eth103/1/15 Down       Po103
      Eth103/1/16 Down       Po103
      Eth103/1/17 Down       Po103
      Eth103/1/18 Down       Po103
      Eth103/1/19 Down       Po103
      Eth103/1/20 Down       Po103
      Eth103/1/21 Down       Po103
      Eth103/1/22 Down       Po103
      Eth103/1/23 Down       Po103
      Eth103/1/24 Down       Po103
      Eth103/1/25 Down       Po103
      Eth103/1/26 Down       Po103
      Eth103/1/27 Down       Po103
      Eth103/1/28 Down       Po103
      Eth103/1/29 Down       Po103
      Eth103/1/30 Down       Po103
      Eth103/1/31 Down       Po103
      Eth103/1/32 Down       Po103
They are not visible: neither with the "show fex" neither with the "show int status", we cannot configure them....?
Do you think it's possible to access these ports by another way and configure them to allow some hosts to connect on it or is their purpose exclusively UPLINK?
best regards,
Eric Gillis

Do you mean the Fabric interfaces? If yes, you cannot use those for any host connectivities.
HTH,
jerry

Front end and console ports are down for switch WS-C3750X-48PF-S

We have a switch WS-C3750X-48PF-S in the stack and front end and console ports stopped working and are down.
I have tried to replug power cable but this didn't help, please let me know if I could replug stack power for this switch without outage of other switches in the stack, since switches are connected into the ring
Please let me know what might be the possible root cause
#sh switch stack-ports
  Switch # Port 1 Port 2
    2 Down Ok
    3 Ok Ok
    4 Ok Down

Hello,
There is a problem with the stacking connection between switch 4 and 2. Can you try replacing the stacking cable between these switches?

Bank statement lines are unreconciled status even after the auto recon

In Cash Management, Bank Statements Loaded, Imported and Reconciled, but for the AP Transactions bank accounts there are few statement lines that are in unreconciled status and few are in reconciled status.
IN bank statement line the Error code was : No matching payment, No matching Open Interface transactions, No matching payment batch,

Hi,
1) please check whether you are using the correct bank statement for reconciliation in case if you have multiple bank accounts / Statements.
2) Check whether the payments that were unreconciled were all functional currency or foreign currency payments ...in which case exchange rates might be causing this ..
References:Autoreconciliation Execution Report Shows Exception No Matching Payment Batch [ID 166716.1]
Autoreconciliation Has No Matching Payment and No Matching Payment Batch Errors for Foreign AP Payments [ID 1387334.1]
Regards,
Ivruksha

SAS MPIO Driver Server 2012 HCT Fails with "make sure two ports are connected" error even with two ports connect

We are running the Server 2012 HCT against a SAS MPIO driver for a server platform with dual redundant storage controllers. The test fails with this error:
(x) For non-iSCSI test environment, please make sure at least two HBA ports are connected to the storage target.
File=testsrc\driverstest\storage\wdk\mpiotest\logotest\devicelib\mpiodevice.cpp Line=2772
Error: 0x0, Error 0x00000000
The system does have two ports connected so the cause of the error is unclear to us. We do not have any problems when running the 2008R2 HCT. Are there any known issues or fixed or workarounds for this problem?

Sorry, maybe I should say WLK rather than HCT. We are trying to submit the SAS MPIO driver for WHQL signing.
Here is a sample MPIO snapshot where you can see our driver is controlling five drives each with two paths.
MPIO Storage Snapshot on Wednesday, 17 April 2013, at 18:31:40.275
Registered DSMs: 2
================
+--------------------------------|-------------------|----|----|----|---|-----+
|DSM Name | Version |PRP | RC | RI |PVP| PVE |
|--------------------------------|-------------------|----|----|----|---|-----|
|Microsoft DSM |006.0002.09200.16384|0120|0003|0001|030| True|
|Intel(R) Storage Controller MPIO|004.0001.00140.0002|0120|0003|0001|030| True|
+--------------------------------|-------------------|----|----|----|---|-----+
Microsoft DSM
=============
No devices controlled by this DSM at this time!
Intel(R) Storage Controller MPIO Driver
=======================================
MPIO Disk4: 02 Paths, Fail Over Only, Explicit Only
SN: 2263015539BAB
Supported Load Balance Policies: FOO RR RRWS LQD
Path ID State SCSI Address Weight
0000000077000001 Standby 000|000|001|004 0
TPG_State: Standby , TPG_Id: 1, TP_Id: 6
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: EBF4115500000000 (State: No Controller)
0000000077000000 Active/Optimized 000|000|000|004 0
* TPG_State: Active/Optimized , TPG_Id: 0, TP_Id: 3
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: D1FBD25300000000 (State: No Controller)
MPIO Disk3: 02 Paths, Fail Over Only, Explicit Only
SN: 22201556966AB
Supported Load Balance Policies: FOO RR RRWS LQD
Path ID State SCSI Address Weight
0000000077000001 Active/Optimized 000|000|001|003 0
* TPG_State: Active/Optimized , TPG_Id: 1, TP_Id: 6
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: EBF4115500000000 (State: No Controller)
0000000077000000 Standby 000|000|000|003 0
TPG_State: Standby , TPG_Id: 0, TP_Id: 3
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: D1FBD25300000000 (State: No Controller)
MPIO Disk2: 02 Paths, Fail Over Only, Explicit Only
SN: 226E01556E6C5F
Supported Load Balance Policies: FOO RR RRWS LQD
Path ID State SCSI Address Weight
0000000077000001 Active/Optimized 000|000|001|002 0
* TPG_State: Active/Optimized , TPG_Id: 1, TP_Id: 6
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: EBF4115500000000 (State: No Controller)
0000000077000000 Standby 000|000|000|002 0
TPG_State: Standby , TPG_Id: 0, TP_Id: 3
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: D1FBD25300000000 (State: No Controller)
MPIO Disk1: 02 Paths, Fail Over Only, Explicit Only
SN: 227C01558F689E
Supported Load Balance Policies: FOO RR RRWS LQD
Path ID State SCSI Address Weight
0000000077000001 Standby 000|000|001|001 0
TPG_State: Standby , TPG_Id: 1, TP_Id: 6
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: D1FBD25300000000 (State: No Controller)
0000000077000000 Active/Optimized 000|000|000|001 0
* TPG_State: Active/Optimized , TPG_Id: 0, TP_Id: 3
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: 6E9AD05300000000 (State: No Controller)
MPIO Disk0: 02 Paths, Fail Over Only, Explicit Only
SN: 22F10155FB941D
Supported Load Balance Policies: FOO RR RRWS LQD
Path ID State SCSI Address Weight
0000000077000001 Standby 000|000|001|000 0
TPG_State: Standby , TPG_Id: 1, TP_Id: 6
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: D1FBD25300000000 (State: No Controller)
0000000077000000 Active/Optimized 000|000|000|000 0
* TPG_State: Active/Optimized , TPG_Id: 0, TP_Id: 3
Adapter: LSI Adapter, SAS 3000 series, 4-port ... (B|D|F: 004|000|000)
Controller: 6E9AD05300000000 (State: No Controller)
MSDSM-wide default load balance policy: N\A
No target-level default load balance policies have been set.
================================================================================

Down State stays after back button pressed on browser

I have built a Navigation Bar in Dreamweaver CS5. I want the nav images to indicate what page you are on by showing the down image state. This is a check box within the Navigation options "Show 'Down Image' initially". This works fine on all pages as long as you use the buttons to navigate, but when you press the back button on the browser (safari & firefox), the page that you have just come from also stays in the down state, affectively showing 2 down states. Has anybody had a similar problem and can help.

Hi
This is standard behaviour with browser back buttons, if the page is in the browser cache they will display the page in the same state as the cached page.
PZ

How can I encrypt my data links between switch uplink ports ? I'm unable to use "cts Manual" command in C3560X switch.suggest me

How can I encrypt my data uplinks between switch trunk ports ? I'm unable to use "cts Manual" command in C3560X switch.suggest me as I want to encrypt my switch-to-switch link with Cisco TrustSec.

Hi
Login to switch & go to interface..
There you can give tags.. (ISL & DONT1Q)
Command switch-port mode trunk
Switch-port trunk encapsulation ssl or dot1Q

Can we remain in the same state even after clicking submit button?

Hello All,
Can we remain in the same stage even after clicking submit button? Also it should remain in the same stage only when certain conditions are met. For eg:
Condition : In Stage1, CustomFieldA default value is 'No'. To pass from Stage1 to Stage2 the CustomFieldA value should be made to yes.
Scenario 1 : CustomFieldA value is 'No', and I click on Submit .
Expected Result : should remain in the same stage
Is above result achievable in PS 2013? I am creating workflow in Visual Studio 2012, so can I handle this in the workflow?
Please help.

The above answer was proved wrong, so please follow this link to get the answer.
http://social.msdn.microsoft.com/Forums/en-US/8c75d74d-1ea6-4273-96cd-e70f5a5688fc/how-to-remain-in-the-same-stage-even-after-clicking-submit-button?forum=project2010custprog

Request stays in Authorizing state even after approval

I've been trying to debug this for days now and it completely breaks my lab - until it fixes itself after some random time and then breaks again
I created a simple approval workflow which seeks approval from [//Target/Owner] when joining an Owner Approval Group. The request makes it to the Group Owner, but when the group owner approves the request, it stays stuck in Authorizing state and the user
doesn't become a member of the group. The WF also remains in Running status even after the request is approved.
I've seen some similar problems around on the internet, and all seem to suggest Exchange related issues. I don't have an exchange setup in my lab, but I don't think not being able to send an email would completely break the approval process. Besides, it
does seem to spring back to life randomly and it all starts working again before breaking - very intermittent.
I've been messing around with the PS WF activity (which I use to calculate custom approvers), but I have disabled that WF completely for now and I'm just using OOTB activities and approvers.
Any suggestions on what the issue could be (apart from exchange)? There are no errors in the event logs either, but there are loads of exchange related errors/warnings which are expected. Alternatively, is there somehow I can disable the "feature"
where FIM tries to send an email?
Thanks

Yep, the approval responses are generated but the request still stays in Authorizing with the workflow in Running state.
What makes this even more bizzare is the intermittent nature of the issue, it just seems to resolve itself after some time then break again.
One thing I have noticed is that the problem starts when I use my custom WF to add approvers to the WF dictionary - the first activity is a powershell activity which calculates the approvers and the next one is the OOTB approval activity which sends an email
to [//WorkflowData/Approver]. However, the PS script runs just fine, and the approver gets the request but after approval nothing happens (although approval responses are generated)

Load step in Yellow state even after completion

Hi people:
I have a situation here with aprocess chain.
When the process chain is triggered,there is a load step which stays
in yellow even after the load completes. We tried to push the step
forward,but the chain wont progress. So,we had to do the rest of the
steps in the process chain manually.
Why does this hangover step happens in the process chains?
Can some one give a solution to this situation, so that we don't have
to do the steps manually everytime the chain is struck at the step?
Any inputs are appreciated.
Thank you.

Hi,
Check the status of the Process Variant in RSPCPROCESSLOG table. If the status of the variant is not 'G' then the process will not move to the next step though the loads complete succesfully.
In this case you have to change the status to 'Completed' (G)manually.
This could be done using the Function Module 'RSPC_PROCESS_FINISH'.
Provide the below details in the FM
1) I_LOGIN - Login ID of your process variant (you can find this in RSPCPROCESSLOG table)
2) I_TYPE = CHAIN
3) I_VARIANT = Your Proces Chain variant (Optional)
4) I_INSTANCE = Double click on the object which was struck and click on Backg tab. Copy paste the instance.
4) I_STATE = G.
Hope this would resolve your issue.
Regards,
Anil Pragada

Why the Fibre uplink ports are down state even after giving no shutdown command at the interface

Similar Messages

Maybe you are looking for