Why the ringing voltage closely 0v for VIC3-2FXS/DID port?

Initially, I have tested every port of FXS module on ISR with an analog phone. There
was ringing tone and I was able to communicate to other as normal. The second
test involved measuring the ringing voltage on the same ports by using a pair cable and multimeter. The
'idle voltage' measured was around 44V and when there was an incoming call, the measured 'ringing
voltage' was close to 0V.
So why the ringing voltage is drop to 0V?
Please advice.

You cannot measure ringing voltage with a common multimeter. Read why:
http://www.sandman.com/ringvoltbul.html

Similar Messages

  • Why the ios 8 non is for iphone 4?

    why the ios 8 non is for iphone 4?

    Because iOS 8 requires a dual-core processor. The iPhone 4 has a single-core one.
    (113179)

  • F.05 -   why the entries are being reversed even though I did not tick the

    Hi,
    Please advice why the entries are being reversed even though I did not tick the reversal button in F.05.
    Your assitance is very much appreciated.

    Hi,
    It is a standard SAP procedure by which the revaluation entries are automatically reversed. If you do not want to reverse the revaluation entries, you will have to Activate Delat Logic for the Valuation Area. SPRO Path is Financial Accounting (New)--> General Ledger Accounting (New) > Periodic Processing> Valuate --> Activate Delta Logic.
    Once you activate this Delta Logic, at the time of fc valuation, you will get the check box for Annual or Mid Term revalation will come. If you select the annual option, the automatic reversal will not happen.
    Regards,
    Amit

  • How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router

    Hello
    I'm looking for information on how to install 2 newly purchased cards  and keep running into dead links. The cards I bought are for a  CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco  router:
    vic3 2fxs/DID and a vic2 2fxo.
    I keep finding documents on how to  install these cards but all links are dead and leading to nowhere.
    http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
    The  2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco  2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco  router.
    NOTE: I've never installed these cards and am not sure if:
    Does my  ios support both of these cards?
    and which slots do I install those in the  router.
    I have 4 slots like this:
    slot 0: This slot only accepts VIC's   ***This could be used for the vic3 2fxs/DID card correct?
    slot 1: Nothing  written here  ****What can i install in this slot?
    slot 2: This slot only  accepts VIC's and WIC's  ***If I buy a WIC and install here which other slot can  i install my VIC2-2FXO card in ?
    slot 3: Nothing written here  ***What can i  install in this slot?
    Any chance someone can help me out with this.
    Thanks  very much

    Ok
    I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
    Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
    If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
    Thanks

  • VIC3-2FXS/DID VS VIC3-2FXS-E/DID

    hi all,
    we'll upgrade our router from 2811 to 2911.
    the current 2811 uses VIC2-2FXS but saw on cisco's website that we need a VIC3 instead.
    i saw there's two versions of this card, the other has an 'E'.
    what's the difference between the two? can i just get a VIC3-2FXS/DID?

    Hi John,
    The difference is explained in the following link
    http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/ip-communications-voice-fax-network-modules/product_data_sheet0900aecd801c595e.html
    VIC3-2FXS-E/DID is designated as an "Off-Premise Extension Lite" product offering. This means that while the module addresses a subset of the off-premise extension applications, it should be noted that the module is not in full compliance for off-premise usage.
    HTH
    Manish

  • Vic3-2FXS/DID fax problem

    I have a network in Beijing China below,
    (1) E1 Pri interface to PSTN
    (2) Vic3-2FXS/DID to fax machine
    all these modules installed on Cisco 2900, when I call my fax machine from PSTN, the fax machine answered, but fax can't start.
    I want to know is there any special consideration about the fax configuration to be worked.
    Thanks for your advice.
    Robert
    2011/2/18

    Hey Robert.
    Since you have PRI and the fxs port on the same card, in theory there is not a whole lot you need to do with regards to the fax or port configuration on the router if this is H323 or SIP.  On our initial voip gateways even on port to port calls we would invoke fax relay, but on the ISR line with the internal tdm backplane, the dsp should be dropped from the call with minimal impairment of the connection through the gateway.
    Now, this is true as long as you don't have "no local-bypass' configured under the voice-card.  Default is that this is not configured but it you do, you should change it to local-bypass.  "show voice dsp active" will show if the dsp is still in the loop on the call as well.
    Definitely check the E1 controller ("show controller e1") for slips and errors.  This will kill a fax if present.
    Looking back at your previous post though, I would not expect you to be seeing G722 on the output of the show voice call summary when the call connects between the two ports.
    Are you using MGCP?
    When the call is active between the two ports, what is the output of "show call active voice brief" and "show call active fax brief"?
    There are a few good resources for troubleshooting fax issues.  An excellent source if the CiscoPress publication "Fax, Modem and Text for IP Telephony".  If you would like some of the scaled down versions, I have posted a couple of links that would be useful.
    Bryan
    https://supportforums.cisco.com/community/netpro/collaboration-voice-video/ip-telephony/blog/2010/10/26/fax-configuration-and-troubleshooting-project
    http://www.cisco.com/en/US/docs/ios/12_3/vvf_c/voice_troubleshooting/old/vts_fax.html

  • VIC3-2FXS/DID

    Hi everybody,
    We have a CCM version 4.x and we need to connect two fax extensions on a VIC3-2FXS/DID card.
    The problem is that the faxs are 6 floors up the CCM. Between floors are connected by Optical fiber thought Cisco Switchs. We can configure these faxs on that card?
    Thanks!!

    VIC3-2FXS/DID
    If you have copper pairs to connect, yes.<-- means that if we connect the faxs to a switch and the VIC3-2FXS/DID  to the other switch with Ethernet cable it will work?
    VIC3-2FXS/DID

  • Why the dependency of "Site settings" for the "About me"-button in the top menu?

    Hello, I recently had a customer case where the customer asked why certain users couldn't see the "About me"-button in the top personal actions menu, after they clicked at the user name/avatar. Only user details, "Sign out" and "My
    settings" was visible for the user, who had an user license and a my site. There was also no customizations whatsoever in either javascript or css that could cause this, and the masterpage or the personal actions control doesn't seem to actually have
    anything to do with the "About me"-button.
    After some tracing and testing of Microsoft's code so we now know why the "About me" is not visible to all users. "About me" button depends on whether the "Site
    Settings" is available in the menu or not. For the "Visitors" then there is no "Site Settings" because of their "Read"-permission level and thus does the "About me" button not appear in the menu. 
    In sposuitenav.js there is a loop for all ie:menuitem and inside of that there is these lines:
    if(menuItem.id.indexOf("MenuItem_Settings") > 0) {
    hasSiteSettingsMenuItem = true;
    And a bit further down the code there is this:
    if(!hasSiteSettingsMenuItem) {
    a.AboutMeLink = null;
    Which will cause so that the "About me"-link is null and is not rendered in the personal actions menu. Otherwise the AboutMeLink would have had the default value that is set by the code earlier.
    So my question really, is why have Microsoft made the "About me"-button depending on whether or not the "Site settings" is visible for the user?
    Because neither I nor my client can understand why there should be any relationship between Site Settings and the About Me link. Shouldn't anyone be able to go to their "my site"? As long as they have one, I can't see any reason to prohibit
    anyone else than site administrators to see and use the "About me"-link.

    It's a recent change it seems, people on the Office 365 Yammer network have noticed this as well. Microsoft has confirmed this as an issue and will work to fix it.
    Join there if you haven't already :)
    https://www.yammer.com/itpronetwork/#/Threads/show?threadId=466244664

  • Is there a way to change the ring tone to none for one particular contact?

    I see there is an option to turn the text message settings for a particular contact to 'none'.  Is there a way to change the ring tone to 'none' or 'silent' for only one contact.  This is a person who calls way too often and I used to turn their ringer to 'none' when I had a blackberry.  This way I can talk to this person when it is convenient for me and not have to listen to the ringer everytime they call.

    You need to sync a silent ringtone to your phone & then assign it to that contact. Here's one already made:
    http://richardkmiller.com/702/iphone-tip-use-a-silent-ringtone-to-screen-calls-i n-your-sleep

  • Why the new Android permissions requirements for AIR 4.0.0.139?

    When starting to update my AIR app to 4.0.0.139 on my Android devices through the Google Play store I found a number of new permission requirements.
    They are:
    New: Approximate location
    New: Receive data from Internet
    New: Prevent tablet from sleeping
    New: Find accounts on the device
    So does this mean that flash apps not using a captive runtime will no longer have to directly request these permissions from the user because the AIR libraries have already acquired them? This could be misleading to the user who installs an AIR app that will have far greater permissions that what they thought they were approving.
    My big question is why are these permission needed? As a developer I submit the Android permissions I need for my app into the application descriptor file. So why does AIR itself need all these extra permissions?
    As a consumer i've started finding too many apps that want access to run at startup, know my location, or contacts, or accounts, with no apparent reason for it. I've been uninstalling such apps or refusing to update them further. Does Adobe worry that other consumers may follow suit? Does the AIR libraries really need these permissions? Why?
    Thanks in advance.

    This is typical of Adobe and how they have always been. They do whatever they want with absolutely no respect or consideration for the user. Not only did they add several new permissions, but they don't have any way to contact them about Air. The email listed on the Google Play page isn't valid, there's no contact info listed on the website, and if you try to submit a question to them Air isn't even an available option. It just goes to show how little they care about the users of their products. And then when someone like yourself goes to the trouble of asking them about it the only way possible, they ignore the question. Which says they don't care, they're hiding something, or both. In any case, I've always hated Adobe and steered clear of their products as much as possible because of this behavior, and I will continue to do so. I won't be letting this app have all these permissions without so much as an explanation why, so I'll be uninstalling it and just won't use any apps that require it, which to my understanding is mostly games, so I'll live. I just hope their disdainful attitude toward their users catches up to them and they crash and burn. We're on the right track with HTML5 moving away from Flash.

  • Why the itunes radio keep asking for internet connection

    I recently changed broadband provider and since then whenever i try to access the music store or the radio the app ask for internet connection even when i am online

    No idea what the fix is but I just want to say I am having the same problem
    Stop asking for my ****ing password itunes - remember it please!

  • DSP Resource for VIC3-4FXS/DID on NM-HDV2

    Hi,
    If only PVDM3 is installed on the C3945 motherboard (Slot 0), and I have VIC3-4FXS/DID inserted in the NM-HDV2 and but without PVDM2 installed in the NM-HDV2, can I still enable the FXS port?
    Do I need to have this command to enable dsp sharing with the NM-HDV2?
    voice-card 1
    dsp tdm pooling
    Also, should the FXS ports appear in the "show voice port summary"?
    Thank you.

    Hi,
    just refer this
    http://www.cisco.com/c/en/us/products/interfaces-modules/2800-3800-high-density-packet-voice-digital-signal-processor/index.html
    Are the PVDM3 modules supported in a NM-HDV2?
    A. No. You cannot install PVDM3 modules directly on the PVDM slots of an NM-HDV2, only the PVDM2s are
    supported by the NM-HDV2. However, an NM-HDV2 that has no PVDMs installed at all can share PVDM3 DSP
    resources from the router motherboard PVDM slots across the chassis backplane.
    Q. Do the PVDM2 modules work with the Cisco 2900 and 3900 Series platforms?
    A. Yes. You can install PVDM2 modules on the motherboard PVDM slots using special adaptor cards (PVDM2-
    ADPTR). You can also insert an NM-HDV2 module with PVDM2 modules into the service-module slot of the
    Cisco 2900 and 3900 Series platforms using the network-to-server module adaptor card (SM-NM-ADPTR).
    regds,
    aman

  • In the former version of iTunes there was an option by means of which I could see the most recent podcast even for those I did not subscribe to. Apparently, with 11.2 this option is gone. Any help?

    Hi folks,
    in former versions of iTunes I could update the list of available podcasts even for those I did not subscribe to.
    Where is this feature in iTunes 11.2?
    Help is appreciated!
    Regards
    Klaus

    well nobody bothered to give me a hint on what to do, maybe because the problems with the new version of iTunes are really a lot, there is an enormous amount of people out there that have all sort of different problems including mine  so I have decided to return to the previous version which works fine and wait untill the apple people come up with a decent product ....

  • Why the socket is closing

    Hi ,
    I would like to send the MimeMessage object via socket connection. To do do that i have written the following code fragment
    Socket s = new Socket("localhost",3200);
    OutputStream os = s.getOutputStream();
    MimeMessage mimemessage
    //some code to create MimeMessage
    mimemessage.writeTo(os);
    os.close() // this is important step
    In this code fragment if i didnt close the output stream the message is not being delivered to the server side. But when i close the output stream it is closing the socket connection with the stream connection.
    What i neeed is i will be sending mimemessage objects via socke asynchronously. For that purpose i would like to keep the outputstream of the socket keep opent always. But how can i send the mimemessage object via socket without closing the stream.
    I tried os.flush() also. but no result.
    Please help me.
    thanks in advance,
    Sridhar reddy .R

    I am not using any server n server is simple java server socket.
    here is the code for server
    public class MyServer extends Thread
    public static void main(String[] a)
    ServerSocket sss= newServerSocket(3200);
    while(true)
    Socket s = ss.accept();
    new MyServer(s).start();
    public MyServer(Socket socket)
    this.socket = socket;
    is = socket.getInputStream();
    public void run()
    while(true)
    Properties prop = System.getProperties();
    Session session = Session.getInstance(prop, null);
    MimeMessage mimemessage = new MimeMessage(session,objectStream);
    // do some operations on this message

  • Why the mouse ( any kind ) halts for 5 mins every time when I start Mac Pro

    As soon as I start my Mac Pro, the apple logo appears abnormally long. When it finally comes into the system, the mouse icon moves but I cannot click into any of the desktop icons.
    I have reformated my harddisk, but the problem still appears. Does any one know how to fix my problem?
    thank you

    Normally I would say a combination of *Disk Warrior* and SuperDuper to solve the issue, and look for any/all (bad) usb cables and devices (hubs and printers too).
    Don't import your old prefs etc and keep it clean while you test and look for why.
    But normally a long logo 'gear' etc = corrupt caches or disk directory.

Maybe you are looking for