Why will MacBook not restart after latest update installed

I have just installed latest osx update on my macbook and now it will not restart. My screen opens with the Apple motif and the spinning wheel but it does not progress, merely keeps spinning. What can I do? Help would be appreciated

The following support article is somewhat outdated. Where it refers to booting from an installation disc, you should boot from your recovery partition (if running Lion) by holding down the key combination command-R at the chime.
Mac OS X: Gray screen appears during startup

Similar Messages

MAC Mini does not restart after Yosemite update

I bought my MAC mini in 2011 and I successfully updated to Mavericks with no problems. I am not sure why my MAC Mini will not restart after I updated to Yosemite. The completion bar gets stuck around 30%.
Any help or ideas appreciated
Larry

Okay, this is strange. I tried restarting three times yesterday with the same results. In fact I left it go overnight only to find the next morning that the bar was still stuck at 30%. I did a hard boot a little bit ago and waited a few seconds. I restarted an it booted up fine.
Larry

Why can't I open iTunes or apps on ipad1? And why do apple not support the latest update for ipad1 when it's less than 2 years old. I am sick of huge corporations ripping off joe public!

Why can't I open iTunes or apps on ipad1? And why do apple not support the latest update for ipad1 when it's less than 2 years old. I am sick of huge corporations ripping off joe public!

And the processor limitations.
iPad: RAM - 256MB, Processor - 1 GHz Apple A4
iPad 2: RAM - 512MB, Processor - 1GHz dual-core Apple A5
iPad 3: RAM 1024MB, Processor - 1GHz dual-core Apple A5X
Similarily, the iPad 2 did not get Siri and some other features in iOS 6.
 Cheers, Tom

Itunes will not launch after latest update 2/2014

Just installed latest update for iTunes on 2/21/2014 on my MBP running snow leopard and after restarting MBP iTunes will not launch.
Thank you
MacBook Pro
Late 2008 unibody running Snow Leopard 10.6.8

Yes, first, I would run Disc Utility; Verify Disc, Verify Disc Permissions, & Repair Disc Permissions.
Then I would go here > http://www.apple.com/itunes/download/ for the .dmg file download.
Then I would reinstall iTunes. So, unless you do not have enough free space on your hard drive, that should work.
Otherwise, it may be time for some spring cleaning...
Regards,
mm~

Podcasts badge still not working after latest update WHY??

I was hoping the latest update would have fixed the problem with the badges in podcasts! But no still the same!
It's just crazy to me they used to work before i think it was version 5.2, you just opened the podcast apps and the badges told you how many unplayed episodes you had perfect!
Now you have to open each podcast and then come out for the badge to work WHY??
I have tried to go back to version 5.1 but no Apple will not let me so stuck with this inferior version!

Take the device to Apple for evaluation, most likely the hardware has failed.

My iphone will not charge after latest update.

After I did the latest update first my middle button stopped working then the volume stopped working but both were fixed after a restart. Now my phone won't charge I get the message cable not compatible but it's the charger that came with the phone. Please help.

After a full 8 hour charge it only shows about 40% charge. This phone worked without incident before the last two firmware updates. I use the same wall charger and Apple cord for my iPad and wife's phone (she has not updated her phone to iOs 6.0.1) and they all work great. There must be something in the new update that kills battery life. By the way, I replaced my battery less than a month ago.

ITunes will not launc after latest update (Mac version)

Hi
I was prompted by the software updater to update iTunes the other day, and so I did. When I first launched iTunes after the update, there was the usual window where i had to agree on Apple's this-and-that that always follows an update, but then nothing happened. After a while, Finder said iTunes was not responding. Now everytime I attempt to launch iTunes, the little triangle will appear beneath the iTunes icon in the dock as if the program was running, but nothing happens. It immediately stops responding, and I cannot even force close it. It's a bit like Windows...
Anyone else with this problem, and maybe with a solution?

I do not get any error code when launching iTunes or double-clicking a audio file. iTunes attempts to launch (bouncing icon in dock), then stops responding.
I have now tried repairing disk permissions and deleting iTunes-related files from the personal/library/preferences folder, all to no avail.

CF 10 will not restart after running Update 3 [updated]

Just tried to apply Update 3 to CF10 and while trying to restart it did not. (Yes, I did have the Mandatory update installed.)
How can I fix it or roll it back?
Thanks for your help,
Randy
Figured out how but wasn't exactly as indicated
From the command prompt (Windows), run:
C:\ColdFusion10\jre\bin\java -jar C:\ColdFusion10\cfusion\hf-updates\hf-10-00003\uninstall\uninstaller.jar
If you look a the the discussion on the Blog post about the Update you will see that this is happening to others.... I would hold off on installing the update.
Randy
Message was edited by: rheaps

I keep getting a black screen with a request to restart in a few languages
That is referred to as a kernel panic.
Help here for Resolving Kernel Panics

HT1192 caps lock function does not work after latest update

Hi there,
I have a Macbook 13" Early 2011 and recently after updating my operating system to Mac OS X 10.7.4, i have found that the caps lock button isn't functioning.
At present if i hold or press the button, it is failing to light up or function at all.
Is there a fix for this issue, as i have read that there was an update by Apple to stop accidental pressing of this key, however not being able to access its function at all seems to be unusual.
Your thoughts and opinions would be much appreciated,
Thanks,
Robsterhill101

My Macbook Pro Early 2011 15" (base model) did this to me last night.
I did a PRAM Reset, the generic "Cure All Procedure" for Macs. It worked after, but I noticed that the button had to be pressed at just the right angle and with enough pressure. The light would come on and off and Caps Lock functions properly. Continued as normal.
I put the computer to sleep by simply closing the lid, and then put myself to sleep as well.
This morning, just before I came on here, my computer would NOT wake from sleep (a whole other issue). Would not wake up by pressing the power button. So I had to do a hard reset, hold the power button down, and press it again after...grrr I never feel good being forced to do this.
Anyways long story a little bit shorter, I restarted my computer and low-and-behold the Cap Lock is not working again. No Bueno, Cupertino.
No, sorry, no liquid damage on the keys, and I don't have kids, nor share my computer with anyone but myself.
Its one of the few things that bug me about this computer. The other is the issue of the computer not being able to wake from sleep. Too often.
SHOULDA BOUGHT THE APPLE CARE
Simply Because, perfect timing after the years original warranty, you will experience problems. After all, they do want you to be a repeat customer. IYKWIM

Why can't I boot after latest update for lion?

I installed the latest update for lion and now my computer won't boot. I got into disk utily it's saying I need to reinstall my os. Please help

Reinstalling Lion Without the Installer
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alterhatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer.

Why will photoshop not open after loading it to new iMac computer from an external hard drive and I get this message: Licensing for this product has stopped working:error code: 150:30

Why will Photoshop CS4 not open after loading to new iMac from an external hard drive and I get this message: Licensing for this product has stopped working:error code: 150:30

A Photoshop installation is tied to the machine it was installed on. Moving it to or from a hard drive breaks the licensing.
The answer is easy: Reinstall CS4 from your disc. and apply all updates.
Gene

Fly out tool menus are not working after latest update-help?!

Attempting to click/hold click is not expanding the tool fly out menus in Illustrator after the latest update. I did discover that alt + left click will rotate tools, but I would still like to be able to access the fly out menus. Any help would be appreciated!

''tenderprey [[#answer-668426|said]]''
<blockquote>
So, it sounds like there's a compatibility problem. I didn't realize that Firefox accesses Silverlight in a whole different way. Do you think Firefox needs to be updated/patched to be able to work with the Silverlight plugin again, or does the plugin need to be updated to be compatible with the latest version of Firefox?
</blockquote>
First of all, I´m not a IT guy...just a fan of "firefox".
Regarding your question, since this issue started with the 34.0.5
version of "firefox" it´s my opinion that it´s "firefox" the one that
should be updated/patched to work again with "netflix".
to fix such issue.

Log & Transfer not working after latest update.

I updated Final Cut Pro 6 to the latest update available. Now when I try to log and transfer my DVCPRO-HD files I'm having errors. Some kind of blocks appear all over the video and the sound is fuzzy and goes in and out like the mic is turning on and off. It was working fine for a couple clips but then it started messing up. Any ideas? Is there a way to remove the latest update?

Thanks for your suggestion, it has solved my difficulty. For informational purposes I will publish my post and the solution in hopes it will assist others.
I am running Final Cut Pro 6.0.5. My Sony SR12's drive is recognized during the Log And Transfer process. The problems continue. All of the thumbnails have a grayish/brown band going right through the middle of each one. I am able to play the clip in the Log and Transfer window but as soon as I attempt to drag the clip to the media box, FCP crashes. I had this same problem with iMovie 7 and found that updating to the latest version solved the problem. In this case however, FCP 6.0.5 is the latest version. I have the same problem with Final Cut Pro Express 4.0.1 but again, not with iMovie 7.1.4. I loaded Sony’s XDCAM software as well just in case but it did not do anything to help the situation.
When I trashed the Perian component along with QuickTime preferences it did the trick. I believe it was the old version of Perian causing the conflict with Final Cut Pro’s Log and Transfer option, not the Quick Time preferences. When I installed the newest version of Perian which is 1.1.3 there didn’t seem to be any conflict and the HD clips from my Sony SR12 imported fine with no further crashes.
MacBook Pro 17" 2.33 GHz Intel Core 2 Duo
2 GB 667 MHz DDR2 SDRAM
Mac OS X 10.4.11
Final Cut Pro 6.0.5

Acrobat Pro Not Working after Latest Update to Snow Leopard

After getting the latest update for Snow Leopard I get the following when Acrobat tries to boot:
Process:         AdobeAcrobat [157]
Path:            /Applications/Adobe Acrobat 9 Pro/Adobe Acrobat Pro.app/Contents/MacOS/AdobeAcrobat
Identifier:      com.adobe.Acrobat.Pro
Version:         9.0.0 (9.0.0)
Code Type:       X86 (Native)
Parent Process: launchd [77]
Date/Time:       2010-03-31 11:25:30.253 -0600
OS Version:      Mac OS X 10.6.3 (10D573)
There is more after this but the summary is that it doesn't boot. Is anyone having this problem also? And if so how did you fix it.? I have tried uninstalling and reinstalling Acrobat but with no success.
Thanks in advance.
David

BBfolgart wrote:
Hi Michael,
Thanks for your reply. However how can you upgrade when the program won't boot? I tried downloading again from Adobe but the version that comes over is 9.0. Is there anyway to force a load? Or anyway for Adobe to push me 9.3.1?
Regards,
David
First try removing preference and or .plist files for Acrobat. Then when you get working try this tip below that might help when you update the application and it fails.
I've come across this in these forums That may or may not solve the update issue for "some" people:
<http://forums.adobe.com/message/2692924#2692924>
see if you think. it helps.

Why is my iPhone 4s stuck on 8% battery and why will it not restart for 12 hours when it dies?

I've had my iPhone 4s for almost 2 years now and the only thing I've had done was my battery and charging port replaced about 9 months ago.About a month ago, I noticed the battery indicator was jumping around when I looked at it, then it just stayed stuck on 26% until it I accidently let it die one day. I tried to plug it in to several chargers, but it kept flashing the apple symbol and going black. I tried a charger with a 2.1amp plug in and discovered that the phone turned on, but it will only stay on for 5 minutes or so then it freezes and dies, also, every time it turns back on it shows the correct battery % for that time. So when I leave it plugged in for about 12 hours(possibly when it gets over 50% charged?), it will stay on and I've been using it like that for a month, without the proper battery indication and only able to charge on one specific charger. It's a 16gig, so it's close to full and I'm not sure if that has anything to do with it or not. People have said it may be the battery or some kind of ground that is missing, but I really don't know. Any advice?

I have this same issue... the phone was fine, then 3 days ago then I noticed it was draining itself whilst on charge. Now it charges to 1% and lasts all day on that unless I reboot, then it just says plug it in and wont reboot! I have had a 100% charge, but it drained down to 9% in under an hour and then stayed at 9% all day. This is obviously an issue, so why is Apple not sorting it out?
Also, these kind of comments (BELOW) are about as useful as, "is it plugged in?"
"diesel vdub Atlanta, GA
Basic troubleshooting from the User's Guide is reset, restart, restore.
Try each of these in order until the issue is resolved."
I have tried 3 cables, 2 wall chargers and 2 docks, so it has nothing to do with those. I have cleaned the connections, so it's not dirt. It isn't water damage as the phone has been nowhere near water.

Why will MacBook not restart after latest update installed

Similar Messages

Maybe you are looking for