Why Won't My I Mac G5 Start Up?

I'm having an intermittent problem starting my I Mac G5. I press the start up button and no go. I try and try, unplug the cable, purchased a new cable, done everything I can think of and nothing works. Then suddenly it will start. I thought it might be the cable because once when I jiggled it the computer started up. I decided that I'll take it to the shop when it won't start anymore at all because I fear that if I take it in when it's intermittent they might not find the problem.
Does anyone know what other reasons could cause this sort of start up issue?
The machine in question is several years old and it's a G5 I Mac, 1.6 GHz PowerPC G5, not the Model listed below which is a newer machine and thankfully starts up just fine.

For me, it turned out to be a bad power supply. $60+ plus $38 labor at the local Apple store. If it's the switch, good for you. My Mac was running forever. I shut it down and moved it to another room in the house. When I went to start it, it wouldn't respond to my button press. Took to to the Apple store and had a Genius look at it. He tried resetting something by holding down the power button for a long while. That didn't work. Ended up leaving it for a power supply replacement. I wasn't going to pay for more than that...

Similar Messages

  • Why won't my I-Mac start up?

    I have an I-Mac G4 Flat Screen (lamp shade style) and using MS X.3.? When I go to boot it up, it gets to the screen with the gray apple and progress indicator (spinning gear) and will go no further. I hear the disc clicking but continues to make the same clicking sounds over and over while the progress indicator continues to spin. I've tried to boot in safe mode (holding shift key down) and have waited 15 minutes (I know that safe mode takes longer) but that does nothing. What else can I try?

    Start up from your Mac OS installation disc; insert disc and restart with the C key held down. That will force a restart using the optical drive. At the first Installer screen, go up to the menu bar. With 10.3, there should be a command under Installer to run Disk Utility; select that command. In Disk Utility, do you see the internal drive in the sidebar? If so, under the DRIVE, to you see the volume indented to the right? If you see the volume under the drive, that is good. Select the DRIVE (not the volume) in the sidebar and go to the +First Aid+ tab. Use +Repair Disk+. Note if any disk errors are found, and if any are found, note if they are repaired.
    Quit Disk Utility and Installer and attempt to restart normally.

  • Why won't my creative cloud setup start?

    I'm working on a PC and when I downloaded creative cloud, the set-up icon showed up in my downloads folder, though when I double click on it, it won't start. It will ask me whether I want to run the program and when I click run, the window will then start to blink feverishly and then, nothing. Anyone have any ideas?

    HerphotoshopD have you had any other Adobe Creative software titles installed on this computer previously?  Please utilize the steps listed in Error downloading Creative Cloud applications - http://helpx.adobe.com/creative-cloud/kb/error-downloading-cc-apps.html to reinstall the Creative Cloud Desktop application.

  • Why won't messages on Mac Pro open? error -1712

    messages on macpro won't open.  i'm getting an error -1712

    Hi,
    I would be really interested to know what that was.
    for the Points
    8:05 pm      Tuesday; December 17, 2013
      iMac 2.5Ghz 5i 2011 (Mavericks 10.9)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
     Couple of iPhones and an iPad

  • Why won't Web Proxy Admin Service start on Win Server 2008 installation?

    Hi,
    I've just installed Sun Web Proxy 4.0.13 on my Windows Server 2008 box. I cannot get "Sun Java System Web Proxy Server 4.0.13 Administration Server" to start, it fails with the following event messages:
    In Application logs i get:
    "+The description for Event ID 26 from source c__sun_proxyserver40_proxy-admserv_config cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.+
    +If the event originated on another computer, the display information had to be saved with the event.+
    +The following information was included with the event:+
    +File C:\Sun\ProxyServer40\proxy-admserv\config/server.xml, line 8, column 8: Unknown element 'SERVER'+
    +the message resource is present but the message is not found in the string/message table+"
    ...and....
    "+The description for Event ID 26 from source c__sun_proxyserver40_proxy-admserv_config cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.+
    +If the event originated on another computer, the display information had to be saved with the event.+
    +The following information was included with the event:+
    +File C:\Sun\ProxyServer40\proxy-admserv\config/server.xml, line 8, column 8: Unknown element 'SERVER'+
    +the message resource is present but the message is not found in the string/message table+"
    Any help would be greatly appreciated. I have JRE 6.0u18 installed, and pointed the install to use that directory for the JRE home.
    Many thanks, Mark
    P.S. the proxy server service starts fine, it's just the admin service that won't start....

    Hello,
    Could you please copy the model.mdf and modellog.ldf from
    C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\Binn\Templates
    To
    C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA
    Rebuilding the system databases you will lose lose logins, jobs, SSIS packages. You may have to restore or attach user databases.
    Hope this helps.
    Regards,
    Alberto Morillo
    SQLCoffee.com

  • Why won't iphone sync mac address book contacts?

    I've got an IP4 and a MAC G5 both with most recent software updates.  At around the turn of 2012 I started "losing" new contacts from my phone,  It transpired that the phone and computer were conflicting some how and contacts were not being updated or synced. When I tried to manually input these new details to Address I am told that the Database could not be opened as it is corrupted. 
    How do I resolve this?
    Evmarnel
    9 April 2012

    Okay, if Entourage is syncing to iCal fine, then the problem is not with Entourage, but with the iPhone. (How sync works--Entourage sends it to a central location, and the iPhone and iCal pick it up from there. So you know E'rage is getting it to the central location fine, but for some reason the iPhone is not picking it up).
    In which case things like reset/restore the iPhone might help (read the iPhone manual on troubleshooting and on syncing, and backup the iPhone, and export iCal and E'rage data to an archive before futzing around too much). Reset/Restore are different from a one-way sync that overwrites data, which you might try first---I think you can tell it just overwrite a certain type of data--the settings are down at the very bottom of the Info panel in iTunes 8.
    However, since E'rage should be irrelevant to the problem, you should also search/ask re general syncing problems with the iPhone.
    iPhone manual:
    http://manuals.info.apple.com/en/iphoneuserguide.pdf
    also bookmarked in Mobile Safari.

  • Why won't my ipod sync session start?

    I moved all my music from my itunes from an old computer to a new one and my ipod touch won't sync. It keeps saying that my sync session won't start. How can I sync my ipod?

    Hi, Ms Rudy77.
    Thank you for the question.  You may find these articles helpful in syncing your iPod with your new computer. 
    iTunes Store: About authorization and deauthorization
    http://support.apple.com/kb/ht1420
    iTunes 11 for Windows: Set up syncing for iPod, iPhone, or iPad
    http://support.apple.com/kb/PH12313
    Regards,
    Jason H.

  • Why won't my game Pacific Fleet start?

    My son's Ipod and my iphone has the Pacific Fleet game and it will load but we can't get the game to start
    what's happening or NOT?

    Hi Sallie!
    I have an article here for you that can help you troubleshoot this issue with your application:
    iOS: Troubleshooting apps purchased from the App Store
    http://support.apple.com/kb/TS1702
    Thanks for being a part of the Apple Support Communities!
    Cheers,
    Braden

  • Why won't firefox open? It starts then hangs around 7300k

    I try to start firefox it doesn't. I check the task mgr and it show the process as open but usually stuck at around 7,300k or 1,800k. It will not start in safe mode or with extension off command either. I have uninstalled and reinstalled, run McGlary and SPybot but nothing has changed. It still wont start. About a week ago i ran McGlary and then firefox actaully started, once! But has since gone back to not starting.

    See "Hang at exit":
    * http://kb.mozillazine.org/Firefox_hangs
    * [[Firefox hangs]]

  • Why won't my Power Mac G5 not connect to my Wifi?

    My Power Mac G5 will not connect to my Wifi. I have tried rebooting and other methods, and none seem to work. Any advice or tips would be much appreciated!

    I had the same problem, my G5 didn't find any wireless network anymore.
    After doing lots of trouble shooting as advised on various websites I finally had as last resort a look inside my G5 and sure enough I found one of the connections wasn't plugged in!
    I normally don't use WIFI very often on my G5, so I can't pin point when it stopped, but having said this, I did have my G5 in the Apple store 3 months ago to get a new graphic card. Surely they would have seen the issue and fixed it at the same time, one assumes.
    Anyway, after fiddling around for at least 30 minutes, because I have a Raid card installed and it's covering half of the wifi card, I finally managed to plug in the tiny button and voila the wireless network was working again.
    To find out where your wifi card is, I found this service guide, explaining all the inside parts and where they are.
    http://tim.id.au/laptops/apple/macpro/macpro_early2008.pdf
    Hope that helps somebody else.

  • Why won't Firefox on Mac using Hotmail access or send Attachments?

    My OS X Mac in Hotmail is not able to access files to send Attachments using Firefox.
    I can access and send file Attachments using Firefox in Gmail and other email services, and I can use Hotmail and send Attachments with Safari as my browser.
    But when I'm emailing in Hotmail with Firefox, and click on Attachments, nothing happens.
    JustAnswers MacMedic had me install msn Silverlight to try to clear this up, but it didn't.

    Hotmail has been having a few hiccups lately I'm afraid.
    If you don't see any emails when you log in, or nothing appears after some time, click in the middle of the grey bar on the left which has the word "'''Inbox'''" in it. This usually causes them to magically appear for some strange reason.
    I've read on on a few blogs that Microsoft is working on the problem, but don't hold your breath.<br><br>
    If this suggestion resolves the problem for you, please click the '''Solved it''' button next to this post after you log in into the forum. This will help others searching for a solution to the same problem.
    Thanks.

  • Why won't my new mac mini pair with my bluetooth keyboard or mouse

    I bought a new mini in December. I've been fighting with getting it set up since. It refuses to see/pair with my bluetooth keyboard or mouse. How am I supposed to proceed with setup if I can't even get off the start-up screen???
    1.4GHz
    1.4GHz dual-core Intel Core i5 (Turbo Boost up to 2.7GHz) with 3MB on-chip shared L3 cache

    The Bluetooth devices were probably paired with another computer. You need to "unpair" these Bluetooth devices before pairing with another.
    Try reading this:
    http://davemeehan.com/technology/how-to-reset-an-apple-wireless-bluetooth-keyboa rd-mouse-or-trackpad
    Good luck...

  • Why won't a new Mac Mini won't boot?

    It will boot to the point of the power light being on, the screen is white with the gray apple and the pinwheel is spinning...but that is it! I have reset the NVRAM, the PRAM, and the SMU. Is there anything else I can do?

    It maybe the hard disk is corrupted. You could try booting to the special Restore partition by holding down the letter R when you turn on your Mac and then running Disk Utility to check and repair the hard disk directory.
    A similar but different method is to hold down Command and S when you turn on the Mac, this boots in to a special single user mode and if successful you can then type the command
    /sbin/fsck -fy
    and then press return, this is an alternative way to again check and repair the hard disk directory.
    Worst case, you would again use R when booting to get in to the Restore partition, but then reformat the drive, and then restore from your backup. (You do have a backup?)

  • Why won't my power Mac g5 turn on

    Help?

    2.3 & 2.7 Ghz models have liquid cooling.  Look for a leak of an oddly colored fluid on the rear and inside.
    Check for poorly seated RAM or video cards making sure not to touch the internal parts with static electricity on your hands.   Touching the power supply with one hand should discharge any electricity if the machine is plugged in.  If not sure what is the power supply bring it in for service.
    All models have a PRAM battery, make sure that's under 4 years old.  http://www.ifixit.com may be able to tell you what battery it is, or your user manual which can be found on the http://www.apple.com/support/ section on manuals.
    Check the specs for power requirements by searching your model on Google with support.apple.com as part of your search, and make sure you aren't overloading the outlet.
    Also look for melted capacitors on the motherboard, as that was a problem with some G5 motherboards.  Mostly it impacted iMacs, but it may have impacted some PowerMacs.

  • Why won't my Mac detect my iPhone which was just upgraded to iOS 6.1.  My other phone still at 6.0.1 is detected just fine.

    Why won't my Mac detect my iPhone 4 which was just upgraded to iOS 6.1.  My other iPhone 4 is still at 6.0.1 and is detected just fine.  Is anyone else having this problem?  Everything was working ok before the upgrade and still works except for the detection.  Coincidence?

    After 4 updates to Xcode it started to connect again.  Now it's working fine.

Maybe you are looking for

  • Just updated to Mavericks and now I can't update apps using my Apple ID

    A few days ago I updated my 2012 Macbook Pro to Mavericks. Today I tried to update my apps but instead of asking for the password of my Apple ID, it asked for my dad's ID. The ID section was greyed out. The apps were all downloaded using my Apple ID.

  • How can I copy the channels to a new group, so they would have the same length (in time)?

    Hi, I have several groups with channels of different lengths (time t). I want to make a new group containing the required channels. I did this in Diadem 2012 test version with Call Data.Root and it works. Now I am trying to do this in Diadem 10, but

  • Process Chain in "Undefined Status"

    I have a custom Process Type (ABAP with a return code) that runs in a chain.  The ABAP decides if a day is Monday, Tuesday, etc. If it is not a particular day, it errors out, per the code below. However, the chain variant is in an "Undefined" status,

  • OS 10.4.11 Update & Printing

    I have been using an Epson Stylus Color 740i for years. I recently updated from 10.3.9 to 10.4.11, and I can no longer print. I cannot find any drivers or software updates to fix the problem. Is this printer no longer supported in 10.4.11? Does anyon

  • Decline an incoming call

    As a long term apple iphone user i have always wanted the feature to be able to simply decline a phone call. In this day and age it should be simple to swipe to the left to reject an incoming call. In find this is a necessary feature and should be ad