Why wont my iphone4 to my home network and my router is fine
my iphone4 wont join my home network. it was connected to it before.I have my laptop connected to my network and my apple TV and PlayStation I also have 2 other phones to are connected to it to. I reset all my settings and all so my router.
I doubt that it was due to any Apple update. Note that this router problem does not affect any device which is already connected to the router. They have an IP address and still work. Mobile devices which disconnect and re-connect to your network frequently are much more likely to first see this problem.
Similar Messages
-
Home Networking and Multiple Router Set up Problem
Router 1 (Main Access Point)
X
(Routers 1 and 2 connected via a wireless bridge)
Router 2 (Wired Access Point)
X
(Router 2 and 3 connected via a wired bridge)
Router 3 (Wired & Wireless Access Point) Note:broadcasting under a different SSID
X
Problem:
When I set up a wireless and wired bridge my Internet connection works perfectly and I can connect to the second SSID. If, however, I close out of my browsing session and come back to my laptop several hours later and open a browser, I get the “webpage cannot be displayed” message.
I suspect this has to do with IP addresses changing from the main router after a certain amount of time.
What could be causing this?
What can I do to stop this from happening?
Thanks for any help
EMLRunning multiple router behind router can be tricky and may be the cause of your dropouts if you don't have it configured properly.
Cisco recommends using your best router as your primary router and DHCP server.
The best way to setup for home networks, in my opinion, is to use only one router, and put the other router(s) in bridge mode. Also, make sure your modem is not a router too.
http://www6.nohold.net/Cisco2/GetArticle.aspx?docid=28cee6a2fb0d4176a2210942d1d5836c_Setting_up_the_...
http://homecommunity.cisco.com/t5/Wireless-Routers/Guest-access-never-displays-password-prompt-on-EA... -
I have ipad2, using wifi home network and ios7. Why I cannot play youtube...help!
I have ipad2, using wifi home network and ios7. Why I cannot play youtube...help!
You don't download anything at all. The feature is built into the iPhone 4 already. Your carrier has to support the feature and there might be an extra charge to use it.
You can read about how it works here.
iOS: Understanding Personal Hotspot - Support - Apple -
but my laptop will. so my grandson restarted the home network and the ipad 2 still wont pick it up. but my laptop will pick the home network.
Start here.
http://www.apple.com/support/ipad/assistant/wifi/
http://support.apple.com/kb/TS1398 -
I have a Mac on my home network and also a Systemline music server on same network. My PC was able to find the server but my MAC cannot. I can ping the server from the mac, but cannot actually connect . Also can't add the mac as a location from server, despite following the Systemline instructions that impy this can be done.
Can anyone please advise what I am doing wrong?Hi LowLuster
Thanks for reply. I am not an expert on these sharing protocols but I think I have turned on SMB sharing but still wont connect. I tried adding netwrik drive by using cntrl K in finder and using smb\\network address but nothing. It is driving me mad!! -
I'm currently signed onto my home network and want to go on with another computer but don't remember my password for my network. Does anyone know where to find this? It's a password that I set myself, not the one that came with my router.
It's in your Keychain on the computer you usually use to connect to your network - the "kind" will be "AirPort Network Password".
Your Keychain can be opened by using the Keychain Access program. It is in your Utilities Folder.
Open Keychain Access, and type airport in the search field. You will see a number of entries. Choose the one with the name of your wireless network, open it, and check the box next to "show password". Before it reveals itself you will be asked for your login password - the one you use to log in to your MacBook.
The network password will appear in the box.
Quit Keychain Access. -
Home Network and printer sharing with XP and Vista
I have a home network and printer wired on my PC desktop which runs XP. My Vista laptop has been connected to internet and printer through the home network for past 6 years flawlessly. However, since October my Vista laptop cannot
connect to the network printer, but internet has been working fine.
I've tried to uninstall/reinstall, update drivers, connect via TCP/IP but printer isn't located by add printer wizard. When I plug printer directly into laptop via USB it works fine. I also have tried another xp desktop in the house
and that cannot locate the printer also. Help!
Thanks in advance,
MedicWhat have you tried so far?
Have you seen this yet...
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh1770.html
http://docs.info.apple.com/article.html?artnum=25609 -
Recently I was working on my home Network and lost myPassword for my Home wireless connection. After many attempts, I remembered thepassword and was able to get in. Now the MacBook Pro only works at home on aHard wire connection. I have an additional 9 devices on the same network, allare functioning properly. The Air connection works fine at any other Networksout side the Home connection. I did a PRAM reset, deleted the Network profileand rebuilt in System Preferences. Still unable to connect wireless on Homenetwork. Any Ideas?
I seem to have fixed it by putting <div class="clearfloat"></div> after the navigation bar?
-
Share iTunes Library on home network and edit from all computers?
I'd like to share my iTunes library on the 3 Macs on my home network and be able to edit the library (add songs, edit titles, add cover art, etc.) from any of the computers. Is there a way to do this? Thanks!
We're attempting to work out the same trick on another thread.
http://discussions.apple.com/message.jspa?messageID=6450437#6450437 -
Connect Fios to Cat5e home network AND Coax connections?
My Verizon fios system was recently installed. My home is wired for a Cat5e home network and standard Coax in all rooms. The fios system is currently connected to the Coax connections and the TVs and Fios router all work fine. Problem is that I would also like to use the Cat5e connections for devices that access the internet that don't have wireless capability and are not proximate to the Fios router. Is it possible to connect the ONT to my Cat5e home network so that I can connect other devices directly to the Cat5e outlets, and keep the existing Coax set-up?
I understand that the standard Fios set-up only allows using either an Ethernet output or the Coax output, but not both. Any suggestions?
One option might be to move the router to the basement (where the equipment is located that I want to connect to the Cat5e network), but then the router will likely be too far from the rest of the house to receive the wireless signal. In that case, is it possible to connect a wireless router in another location (I have a Belkin wireless router). Or do I need to get another router from Verizon?DC_Sox_Fan wrote:
I just spoke to Verizon Fios Tech Support and they claim that it is NOT possible to use both the Coax and Cat5e connections. So, for those that have a Cat5e home network, but still want to use th Coax for TV, Verzon says you are out of luck.
Thats not strickly true but its not bad info either. You cant use both the coax and cat5 at the same time for INTERNET. The coax internet port (moca) is not active at the same time as the ethernet port. However, many systems use the ethernet for internet and coax for TV.
Depending on how your house is set up this can be accomplished many different ways.
I would assume that you have some kind of utility closet were all the ethernet cables converge, where you could place the router so that it can connect to all the rooms. Is this correct? If so, is there also a coax connection in there? Again, if so, you could place the verizon router in the closet, connect the coax to the router for the link to verizon and the TV's and then connect the ethernet to the lan for the rest of the house. This would be the simplest way assuming that you have this type of connection available to you. there are many other ways but it would all depend on what you have available to you and how your house wiring is set up
====================================================================================
Error exists between keyboard and chair. -
I have recently purchased an n80 and I am trying to get the home networking and internet functional through my wirless router. So far I have had little success. I have enabled upnp on my d-link router/modem . I have installed The simple center software on my laptop and uploaded files to share. I have setup an access point on my n80 and I have enabled sharing. The shared folders on the n80 have also been selected to share all files. The simple center software has been allowed to operate through xp's firewall. THe only thing I am not sure about is the port forwarding on the router. I have a trigger port and a public port in the applications gateway section of my router . I have entered the ports listed in the simple centers setting section (1900,49153,49154,49152). I have these numbers in both the trigger port and the public port on the TCP protocol.
Occasionally I can connet to the internet. However when I close the connection down and try to start it up again sometimes it does not work , showing 'unable to perform operation'. The only way to re-establish the connection is to power the router down then backup(reset).
The same goes for the home networking. I had no success a all on the first day of trying. Went to work. When I came back tried it again and it worked perfectlly ?? Now on the third day it is working ocassionally.
Anyone else had simmilar problems ? If so any soultions would be appreciated ! The phone itself seems to be pretty glitcy. And battery life isnt the best either. Apart from that eh !Forget that - just sussed it out...
I'm using v3.0617.0.6 (03-05-2006) RM-92, Nokia N80 (31.01)
I can't seem to get anything using the browser - I constantly get "Out of memory" errors, even when trying to use GPRS.
It moans something about "packet data" and then bombs out... -
time capsule first said the back up was delayed, now it won't connect to my home network. my internet is working fine and so is everything else but when i try to connect to the time capsule it says to check my server and ip address and if it continues to contact system administrator.. i didnt change anything, please help!
Lion networking.. just need to reboot everything.. modem TC and the clients.. then it will work.. Sometimes just the TC is enough.. sometimes just the computer. .. Vista golden networking award.. did you turn it off and on again??
-
Why some movies will play on home sharing and others won't
Why some movies will play on home sharing and others won't
Fixed it! I guess that I had installed avast! a few days ago and completely forgotten about it. That seems to be what the problem was, because I uninstalled it and it's working fine now. Thank you though, you rang the bell that reminded me! (:
-
Time Capsul "Guest Network" has gone down and cannot resuscitat. Main Network and back up working fine. Suggestions?
Cisco DPQ 2925 is according to Cisco.....a modem/router or gateway type of device that combines the functions of a modem and router in one package. See info below:
http://www.cisco.com/c/dam/en/us/td/docs/video/at_home/Cable_Modems/3900_Series/ OL-30824-01.pdf
Unfortunately, the guest network feature will not work correctly when the AirPort is connected to the type of "modem" that you have. If that feature is important to you, please check with your Internet service provider and ask them if they can provide a simple modem.....not a modem/router or gateway.
Ironically, we have seen a few posts from users who claim to be able to get the guest network to work with the type of "modem" that you have, but to do so will result in what is known as a Double NAT error on the network......basically two devices both trying to act as the router for the network.
That can result in IP address conflicts and other issues created by the Double NAT such as slow browsing, no browsing, poor communications between devices on the network\, and other unpredictable things.
Sometimes, you can get away with a Double NAT issue on a simple home network, but I would not recommend this type of setup. -
OS is whatever OS ships with current IPOD Touch
I cannot understand why the APPLE engineers have designed this product so that it has SO MANY WIFI problems. This is supposed to be an easy-to-use product. We've had no problems connecting our new laptop, our ROKU box, etc, but it seems impossible to get the IPOD touch to work. NOTHING LIKE SPENDING XMAS MORNING DOING APPLE TECH SUPPORT TROUBLESHOOTING TO LEAVE YOU IN THE CHRISTMAS SPIRIT!!! Argh!
In fact, the only way we have been able to get this expensive brand new IPOD to work on our home network is to DISABLE SECURITY in the router settings. THIS IS ANYTHING BUT A GOOD IDEA.
DON"T KNOW WHY BUT MANY OTHER USERS ARE REPORTING THE SAME KIND OF PROBLEM SO APPLE ENGINEERING NEEDS TO GET BUSY AND FIX THIS PROBLEM SO THAT NEW USERS CAN CONNECT TO THE INTERNET WITHOUT HAVING TO BE TRAINED ROUTER ENGINEERS TO DO IT!!!!
Ok, sorry for the rant, but surely those of you who are experiencing this share my frustration. This is not why I bought an APPLE product.
IS THERE ANY POSSIBILITY THAT APPLE WILL NOT ALLOW A WIFI PASSWORD with more than one identical alphanumeric character? Any ideas? We also tried eliminating the 40 MHZ setting under Bandwidth settings in the router settings for our router, but it made no difference. The router has the latest firmware, too. Running out of ideas, and am ready to box this unit up and send it back!Thanks, Bob! You are correct. And, we learned this as we spoke with APPLE TECH SUPPORT by phone on Christmas day (800-APL-CARE). One of their reps spent the time to help us troubleshoot this, but the boiled down conclusion is your answer, and to repeat for the benefit of others, here is what worked:
1. With our Belkin router set to "out-of-the-box" WEP 64 bit security, we could not get wireless access of any kind. Only with the Security Mode set to DISABLED, could we gain access.
2. Changing the router's security mode setting to "WPA/WPA-2...." and entering a new min. 8 char passphrase, and then entering that same passphrase into the IPOD Touch, and restarting the router, did the trick!
Based on this, and some info found in another posting, I can only conclude that the IPODs and IPHONES do not support WEP security mode in many generic routers used by thousands of consumers. Hopefully, those same consumers can figure out how to change their wireless router setttings to WPA/WPA-2 security mode and ALSO get all their other wireless devices (PCs, laptops, WII boxes, ROKU boxes) all reconfigured to WPA mode, too.
I THINK THE BOTTOM LINE HERE IS THAT THERE IS AN ISSUE THAT APPLE NEEDS TO ADDRESS WITH WEP COMPATIBILITY and it may also be the case that MOST CONSUMERS ARE USING WEP 64 BIT security on their home wireless routers?
In any case, it's working now, so anyone who is having problems should try changing to WPA mode and post back here if it worked for them!
Maybe you are looking for
-
Ajuda no Caminho Completo da Imagem no Upload
Amigos, Será que alguem poderia me ajudar, estou utilizando o ADDT e fazendo um upload de uma imagem, só que para o bando de dados vai apenas o nome da imagem e eu necessito de que para o banco de dados, vá o caminho correto de onde esta há imagem, o
-
Error: while creating Service Entry Sheet - for HELD PO
Hi experts, While PO XXXXXXXXXX is in the status of Hold. System allowed me to create & delete a service entry sheet(SES) on particular date. Another day i tried to create SES for the same PO. System is not allowing me to create SES and it gives me e
-
HI everyone, I'm trying to fix moms macbook Pro A1297 2010 model . Was working fine and then one day it wouldn't turn on. I've tried the basics that I could do so far , here's what I've done and found out . 1. With the charger in ( glowing green) I
-
When I started my PC this morning I got a pop-up message stating that CC has damaged files and required downloading from www.adobe.com/go/adobecreativecloudapp. Indeed, CC did NOT work and subsequent attempts to download CC never got beyond the initi
-
Smart mailboxes: How to create a rule with an OR statement?
I have three different accounts in Apple Mail.app. I'd like to create a smart mailbox that shows just the sent messages from all three accounts in the past seven days. The rule begins with +Contains messages that match all of the following conditions