Wi-Fi Connects then drops after 1min.

Ok, Hello Everyone I really need some help with the C6-01. I really like it alot, but it won't hold a Wi-Fi connection for more than 1min., unless their is an app/program running that utilizes the connection, at which point when the app/program is closed the phone drops the connection. Nokia tier 2 tech support said this is not normal and could not recreate the problem. I have tried mutiple routers with the same results. I believe it's the phone because I have received 2 replacement phones from the retailer and all 3 phones have this problem. Nokia tech support wants me to send it in for repair, but I can't be without my phone for 8 to 10 days that's not including shipping time.
Thanks,
BiggShot
Phone: C6-01
Updated to Nokia Belle Refresh
Firmware: 111.040.1511.22.01
OS 5.3

I seem to be getting the same problem on my E7, wifi stays connected when there's an app open (email) but will close & go back to 3G network otherwise. This seems to have just started although in my case it may coincide with me getting a combined modem & router from my isp.

Similar Messages

Remote App on iPad connects but drops after about 20 mins. Need to turn off wait about 1 minute then turn on wifi on iMac before it can reconnect. Need some help please.

Remote App on iPad connects but drops after about 20 mins. Need to turn off wait about 1 minute, then turn on wifi on iMac before it can reconnect. Need some help please.
Already gone through troubleshooting guide a zillion times. Thanks.

This worked for me... A little time consuming but once you get rolling it goes GREAT... Thanks....
I got my artwork and saved it to my Desktop
Opened up Microsoft Paint and clicked on "File" and "Open" and found it to get it on the screen to resize it
Clicked "resize" and a box for changing it opened up
Checked the box "Pixels" and "Unchecked maintain aspect ratio"
Set Horizontal for 640 and Vertical for 480
Clicked on "OK" and went back to "File" and did a "Save As" and chose JPEG Picture
It came up "File Already Existed" and clicked "OK" (really did not care about the original artwork I found because wrong size)
Went to iTunes and on the movie right clicked on "Get Info", clicked on "Details", then "Artwork"
Go to the little box on the top left that shows your old artwork and click on it to get the little blue border to appear around it and hit "Delete" to make it gone
Click on "Add Artwork" and find it where you put the one from above on your Desktop and hit "Open" and OK and your new artwork is now there and all good.
Sounds like a lot of steps to follow but after around 5 or so you will fly through it. This worked perfect on my iPhone 6 Plus and I have artwork on my Home Videos now.

Mac connects then drops wireless connection after startup

Hi, I have a strange problem. I recently purchased a new MBP. My old MBP didn't have any problems with the router, but my new one, after coming out of sleep, will be connected to the internet for a couple of seconds, then drop it like it's searching for a signal, then be connected for around 20 seconds but no actual internet connection. I know that it initially is connected because I can refresh the page or connect to a webpage for about 5 seconds, but then it starts "looking" for the signal. And of course, once it finds the signal, it doesn't actually work for another 20 seconds. I wanted to blame the router but no other computers have this problem. Can anyone help me?

If you are using W7 -- scrooge is correct - it is not listed on Linksys' W7 Comp. list - http://tinyurl.com/yd2nv5v - but it is listed on Microsoft's Comp. list - http://tinyurl.com/y9vuwdm - confusing!!
FYI - I'm using a #320 router with the WUSB600N adaptor ( Win 7 driver - Ver.3.1.0.1.0 ) on a 64 bit platform desktop with no issues at all - I believe W7 found and loaded correct the driver for the 600 adp. --- or you can check for the correct driver for the adp. in the Device Manager if you decide to try the USB adp.'r

Galaxy S6 Sprint, connecting then drop, wifi poor

When placing calls, almost every call says connecting then it hangs up. Skype never works on 4g/3g. It used to but now the recipients phone never gets the call. When it does dial out it just says ringing and no one gets the call. Is MS having issues with Skype right now?

Lock everything..
Lock wireless channel, lock 5ghz to different name cf 2.4ghz.. lock the mode.
Too much is auto and starts jumping around.
If you still have issues.. tell us how old the TC is. The wireless drops off as they age.
I also suggest you can use AE to reinforce wireless of course but that is expense and results in double hop wireless .. a high power wireless router from another brand can be a better buy. You don't need to use it as a router.. just plug it into the TC as WAP.

4G Connected then dropped back to 3G never to return...

I have been a paitently watiing for over 6 months now for 4G. The VZW rep told me by the end of the year for 4G to be availabe in the Utica NY area. I did some research online and found that Utica was scheduled for 4G coverage by the end of 2011.
Now yesterday morning 11/21/11 around 9:30, I looked at my phone and realized it said 4GLTE and I did a double take, and realized it actually said 4G, now, for my first time ever being able to use it I got really excited. I played a little, downloaded some files, super fast! Even did a speedtest on it and it blew my 3G speeds away as expected!
About 10 minutes later the connection dropped and went back to 3G, then came right back to 4G, then the phone dropped all data connection, went to 1X back to 3G then back to 4G where it held for almost an hour.
After about an hour, it dropped again returned to 3G and it never connected to 4G again. I thought maybe it was the phone, so I did a reboot, and went into airplane mode, back out, and still nothing, only 3G
Now I know that there is no way I connected to a tower that had 4G that is not in the Utica area, the closest tower with 4G near Utica is in Syracuse over 60 Miles away.
So there had to be a tower or towers in the Utica area that had the 4G siginal up for a little while.
Is it possible that VZW was testing the 4G service to get ready for its launch in the area? Or maybe it was a mistake?
Could it mean that it's going to launch in the area soon?
Over the past few months, VZW customers in the area have exirenced lots of call drops and 3G data drop outs, which is uncommon for this area, VZW is always reliable and never drops calls (atleast in this area), some reps said it was due to 4G upgrades on the towers. Is that a true statement?
I know there's a lot of questions here but I'm really curious as to when we'll see a solid 4G coverage in my area!
I really want 4G!
Thanks in advance!
-Mike

Both of the problems you just described is the power saving features built into the phones software. I think I posted this on your post already? haha but anyways, the switch from 3G to 4G or 4G to 3G is probably just causing the software to just get confused basically and shut off the Data connection all together to save battery, it will automatically turn itself back on later when the correct amount of time has passed, every phone is different so I can't really say when lol. But, when in WiFi to save battery and to keep your data usage down some phones will shut the data connection off and rely on the WiFi connection, which isn't necessarily a bad thing.
The software is supposed to be designed to turn it all back on when receiving a MMS message or when the WiFi connection is terminated, but this isn't always the case.
Verizon's version of the Droid software still had bugs that need to be taken care of :/
This is why Custom ROM's become peoples best friends because most issues that are addressed are taken care of very quickly, most of the time anyways.
And you're going back a little ways there lol, but still it would all probably still look exactly the same to use as it did 15 years ago, it really hasn't changed that much, same old same old here, its like this place is stuck in a giant rut that it can't get out of haha

IPad 2 3G on Telus, internet connection with 3G shows full bars connects, then drops as soon as you start loading a web page.

It seems to be getting worse, at first I could get it to work after a couple tries....last night took half an hour to get working....starting to get more than a little frustrating. Wifi works fine, I'm just getting sick of the 3G issue. Once you get it to stay connected it's fine, never drops again.....until you turn it off and go back to the start. Is this a known issue or is my iPad2 defective?
I should also note that the signal strength itself never changes, when the network drops, just the little 3g icon vanishes and safari comes up with "could not load page because there is no network connection"

Fixed

Calls are Connected but Dropped After a Certain Time.

We have a FoIP envrionment and before I start blaming the software, I want to make sure that my routing is properly done. I'm able to place a fax call from one branch office to another but the call gets dropped.
RightFax ---------------à2811---------(out one of the ports of the FXO card)---------àVG248-------------àPSTN------------àFax machine
Attached are the trace of the Vg248 and the running config of the 2811 that I've got setup.
I've used the configuration guide http://docs.google.com/viewer?a=v&q=cache:7VWnAmhhiYIJ:www.cisco.com/application/pdf/paws/44948/faxvg248.pdf+configuring+vg248+to+send+fax&hl=en&gl=ca&pid=bl&srcid=ADGEESgxDmCbg_0MqYYK6Qx_H5yGJcJs-AhCsxgz1LUmi_XHxSLHwxo_DkBfH-NiR3u4HgycyXLy4IiCp9ax_wPbWefMuMTkZK1TBsxr29rmABT_Z7yk8VJSRY-6Iykhv6NTV3O9Uznz&sig=AHIEtbRxjPVEcT2XM3SHB_YW4Z4_97xB3w
for fax-passthrough to help me configure the ports on the vg248.
The dial-peer I'm using right now is this one...
dial-peer voice 6 pots
destination-pattern 91[2-9]..[2-9]...
information-type fax
fax rate fax
no digit-strip
port 0/0/0
Here is the result that debug vpm all showed me.
*May 12 16:09:15.110: htsp_timer_stop3 htsp_setup_req
*May 12 16:09:15.110: htsp_process_event: [0/0/1, FXOLS_ONHOOK, E_HTSP_SETUP_REQ]fxols_onhook_setup
*May 12 16:09:15.110: [0/0/1] set signal state = 0xC timestamp = 0
*May 12 16:09:15.110: dsp_set_sig_state: [0/0/1] packet_len=12 channel_id=129 packet_id=39 state=0xC timestamp=0x0
*May 12 16:09:15.110: TGRM: reg_invoke_tgrm_call_update(0, 0, 1, 65535, 1, TGRM_CALL_BUSY, TGRM_CALL_VOICE, TGRM_DIRECTION_OUT)
*May 12 16:09:15.114: htsp_timer - 1300 msec
*May 12 16:09:15.454: htsp_process_event: [0/0/1, FXOLS_WAIT_DIAL_TONE, E_DSP_SIG_0110]fxols_disc_clear
*May 12 16:09:15.454: htsp_timer_stop2
*May 12 16:09:15.454: htsp_timer - 1300 msec
*May 12 16:09:16.754: htsp_process_event: [0/0/1, FXOLS_WAIT_DIAL_TONE, E_HTSP_EVENT_TIMER]fxols_wait_dial_timer htsp_dial
*May 12 16:09:19.194: htsp_process_event: [0/0/1, FXOLS_WAIT_DIAL_DONE, E_DSP_DIALING_DONE]fxols_wait_dial_done htsp_progress
*May 12 16:09:19.194: htsp_timer - 350 msec
*May 12 16:09:19.198: htsp_call_bridged invoked
*May 12 16:09:19.546: htsp_process_event: [0/0/1, FXOLS_WAIT_CUT_THRU, E_HTSP_EVENT_TIMER]fxols_handle_cut_thru
*May 12 16:09:19.546: htsp_timer_stop
*May 12 16:09:19.566: flex_dsprm_forking_mixing_support:
*May 12 16:09:19.566: mars_flex_dsprm_current_codec_comp:DSP:0 FLEX Complexity Codec
*May 12 16:09:19.566: DSPWARE Version < 3.0 actual is 23.6.0
*May 12 16:09:19.566: flex_dsprm_forking_mixing_support:
*May 12 16:09:19.566: mars_flex_dsprm_current_codec_comp:DSP:0 FLEX Complexity Codec
*May 12 16:09:19.566: DSPWARE Version < 3.0 actual is 23.6.0
*May 12 16:09:19.570: htsp_process_event: [0/0/1, FXOLS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]fxols_proc_voice
*May 12 16:09:19.570: htsp_process_event: [0/0/1, FXOLS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]fxols_proc_voice
*May 12 16:09:27.930: htsp_process_event: [0/0/1, FXOLS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]fxols_proc_voice
*May 12 16:10:00.574: htsp_timer_stop3 htsp_release_req: cause 127, no_onhook 0
*May 12 16:10:00.582: htsp_process_event: [0/0/1, FXOLS_OFFHOOK, E_HTSP_RELEASE_REQ]fxols_offhook_release
*May 12 16:10:00.586: htsp_timer_stop
*May 12 16:10:00.586: htsp_timer_stop2
*May 12 16:10:00.586: htsp_timer_stop3
*May 12 16:10:00.586: [0/0/1] set signal state = 0x4 timestamp = 0
*May 12 16:10:00.586: dsp_set_sig_state: [0/0/1] packet_len=12 channel_id=129 packet_id=39 state=0x4 timestamp=0x0
*May 12 16:10:00.586: TGRM: reg_invoke_tgrm_call_update(0, 0, 1, 65535, 1, TGRM_CALL_IDLE, TGRM_CALL_VOICE, TGRM_DIRECTION_OUT)
*May 12 16:10:00.586: htsp_timer - 2000 msec
*May 12 16:10:00.586: TGRM: reg_invoke_tgrm_call_update(0, 0, 1, 65535, 1, TGRM_CALL_BUSY, TGRM_CALL_VOICE, TGRM_DIRECTION_OUT)
*May 12 16:10:00.590: flex_dsprm_close_cleanup
*May 12 16:10:00.854: htsp_process_event: [0/0/1, FXOLS_GUARD_OUT, E_DSP_SIG_0110]
*May 12 16:10:02.586: htsp_process_event: [0/0/1, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
*May 12 16:10:02.586: TGRM: reg_invoke_tgrm_call_update(0, 0, 1, 65535, 1, TGRM_CALL_IDLE, TGRM_CALL_VOICE, TGRM_DIRECTION_OUT)
*May 12 16:10:02.586: dsp_req_sig_state: [0/0/1] packet_len=8 channel_id=129 packet_id=40
*May 12 16:10:02.586: htsp_process_event: [0/0/1, FXOLS_ONHOOK, E_DSP_SIG_0100]

Sorry...here is the roadmap to how a call is being placed.
faxserver==h323==2811==fxo==vg248==CUCM==PSTN GW==PRI==PSTN=====Fax machine.
I've figured out that there was no Clock line on the controler and the 2811 was using the default dial-peer 0 instead the inbound dialpeer. the problem changed from dropping the call (or timeout) to Line is Busy and the fax server drops the call after 2 secons.
I did a debug isdn q931 and it showed me the following:
000084: *Feb 6 16:26:15.383: ISDN Se1/0:23 Q931: TX -> SETUP pd = 8 callref = 0x0221
        Bearer Capability i = 0x8090A2
                Standard = CCITT
                Transer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98316
                Exclusive, Channel 22
        Calling Party Number i = 0x0081, '9055408208'
                Plan:Unknown, Type:Unknown
        Called Party Number i = 0x80, '16137883600'
                Plan:Unknown, Type:Unknown
000085: *Feb 6 16:26:15.483: ISDN Se1/0:23 Q931: RX <- CALL_PROC pd = 8 callref = 0x8221
        Channel ID i = 0xA98396
                Exclusive, Channel 22
HAMVGP01_3725#
000086: *Feb 6 16:26:17.179: ISDN Se1/0:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x0221
        Cause i = 0x8090 - Normal call clearing
000087: *Feb 6 16:26:17.431: ISDN Se1/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x8221
000088: *Feb 6 16:26:17.443: ISDN Se1/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x0221
HAMVGP01_3725#term no mon
000089: *Feb 6 16:26:27.215: ISDN Se1/0:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x838E
        Cause i = 0x8090 - Normal call clearing
000090: *Feb 6 16:26:27.331: ISDN Se1/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x038E
000091: *Feb 6 16:26:27.343: ISDN Se1/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x838E

Menubar "Time Connected" behavior changed after recent updates

Hi folks I have been using my AXBS (11n with USB) with an DSL connection.
You can choose to display the time connected from the drop-down list from the Airport icon on the Menu bar.
Before this upgrade (Utility 5.5.1 and firmware 7.5.2), the "time connected" shows the time of your current DSL connection, meaning i choose "Disconnect" from that Airport drop-down menu then the AXBS will terminate the current DSL connection and dial up a new connection -- and from this point, the "Time connected" count will be reset to zero. Therefore this is a time count for a single DSL connection duration. It has nothing to do with how long the router itself has been up and running.
But after the current upgrade (Utility 5.5.2 /w fw 7.5.2), drop the DSL connection and redial will not reset the "Time connected". But if you unplug the router's power and re-plug it, it will be reset. That means the "Time connected" is now counting the time the router has been on and running.
Since I have another Macbook pro in the same which is still running the old Airport Utility -- i did my experiment with the old Utility -- results are same with the new Utility. Then I suppose it is a firware thing.
Guys is there anyway to make the "Time connected" to work the way it used to - just showing the duration of one DSL connection. This is important to me. Because my connection speed drops after keeping a connection alive 2 - 3 days - i need to disconnect and re-connect to revive the internet connection. Thanks a lot.

Dylan Neild wrote:
Seeing this as well.
"Time connected" used to show PPPoE session uptime. It now shows device uptime.
Definitely a bug. I filed a bug with the bug tracker so hopefully they fix it in the next release.
Yes I filed a bug too. But it seems Apple doesnt care much about their Airports and i guess it will be a good freaking wait until the next FW update.

SSL connections getting dropped

we have a device sa 520 25 user SSL licence installed but users are experencing connections being dropped after 2 to 5 minutes for no reason. it dosent mater if its only 1 user or more than that they all have the same experence. Have tried looking at the logs but cant see anything there that indicates any issue.

Billy,
When creating the user what idle time out did you specify?
Jasbryan

Hi - my mac mini drops the internet after 30 seconds. If i reset in the diagnosics it works again but then drops it just the same. Its connected to my home network. All other apple devices are fine?

I have a home network which services:
Apple TV
Air port express
Mac book pro
I phone
All the above wrok perfectly.
I have a mac Mini which will join the network and operates fine but keeps dropping the internet after 30 secods of connection?
If I reset everything in the diagnostics box it will rejoin the network but then drops it again !!!
any ideas?
Chris

Hi Chris, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.5, 10.6, 10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x/10.8.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
If using Wifi/Airport...
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.

Restore iphone 4 to install the ios 5 but something went wrong while doing back up and whenever i connect the phone to itunes theres an error and the phone turn off after 1min

hi guys i just downloaded the ios 5 and while it was doing back up something went wrong and everything were stopped and shows me a message as an error msg and now whenever i connect my iphone 4(32g) to itunes after 1min it goes off and the battery full and the same thing happend again and again can u help me guys plz i only see connect to itunes on the screen no options even

by reset option do you mean the DFU restore? worked for me, have you tried that?
if not - hold the lock and home button until the power down bar comes up. then hold the lock button for ten seconds - next continue to hold the lock button and press the home button for ten seconds - next release the lock button and hold the home button for 10 seconds. this should be done with the phone tethered. If done right and your itunes is configured as such, the phone will reload the drivers and start up itunes, and then prompt for a restore/update.

3G connection keeps dropping out after 4.2.1 update

Hi, I'm wondering if anyone could help me.
I have the iPhone 4, and it was working perfectly... until I upgraded to iOS 4.2.1.
Ever since then, my 3G connection keeps dropping out, and I'm just left with vodafone UK (with usually 3-4 bar signal) but no 'o', 'E' or '3G' symbol.
After about 20 minutes of no cellular data, I'd get the 'o' symbol, then 10 seconds later it would change to '3G'. But then after 5 seconds it would lose it. The cycle would continue in this way.
Strangely, when at home, the 3G would stay connected. But when I go anywhere, I lose 3G.
When I turn 3G off, I get constant 'o' connection where ever I go. It doesn't drop out.
I've tried resetting the phone, and resetting network settings.
Does anyone have any ideas?
Thanks.

I'm having a similar issue with my new iPhone 4 (w/ 4.2.1)... It continually cycles through the following sequence:
AT&T / 3G
AT&T / No Data
Searching…
Searching… 3G
AT&T / 3G
(loops…)
Here is a video of the cycling. Note the iPhone 4 is just sitting on a coffee table in my house.
http://dl.dropbox.com/u/7186070/ip4fw421searching.mov
Also worth noting, I just got the iPhone 4 and I updated it to 4.2.1 right away. Previously, I had a 3GS which did not exhibit any of this behavior in the same location in my house. Also, my girlfriend still has a 3GS and has FW 4.2.1 without these issues. I have a video of her phone in the exact same location taken just after the clip above and her phone maintains 3-bars / AT&T / 3G the entire time.
I picked up the iPhone 4 while out of state over the holiday weekend and did not observe any of these connectivity issues, in fact the 3G throughput of the iPhone 4 was significantly better (consistently got >4 Mbps down / >800 Kbps up) than what my family members were seeing with their 3GS models.
I believe it is a baseband issue introduced with the 4.2.1 update for iPhone 4, but I also strongly believe there is some tower component to this problem (ie, software revision at the tower or configuration).
Like others here, I also performed a restore to 4.2.1 through iTunes and setup my phone as "New" and I continue to see the behavior. The phone is unusable in my house unless I manually disable 3G. As a final data point, when I'm able to maintain a 3G connection long enough in my house I get the following throughput from Speedtest.net: 1863 Kbps down / 543 Kbps up.

Wireless connection drops after bout 5 min - HP all in one C6180

Hi!
I'm having problem with my all in one product - HP all in one C6180. The wireless network connection drops, and the printer becomes unreachable from both web-interface and printjobs/scanningjobs etc...
This problem has existed since I bought this machine..
I've tried several different setups when it comes to WEP/WPA/WPA2 etc..and also different channels on the wireless, but still same problem exist. The printer works perfect for about 5 min, but then drops the connection it seems like. I'm having about 5-6 devices connected to my wireless router (Draytek VGI 2910), and all seems to work perfect together except the C6180.
At this moment I'm running WPA2 for security on my network. I've tested the software both on Win/ Mac, and currently running the Mac-version.
Is there any firmware-update out that could solve my problem, or how else should I manage it to work properly?
Thanks for any help!
/V

There does not appear to be any firmware update on this page. It could be a router issue.
Let's set a static IP address for the printer:
- Print a Network Config Page from the front of the printer. Note the printer's IP address.
- Type that IP address into a browser to reveal the printer's internal settings.
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you do not know the range, set a high IP address, like .250
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Enter your router's IP (ends with .1) for the gateway and first DNS. Leave the second one blank.
- Click 'Apply'.
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you may need to redo 'Add a Printer' using the new IP address.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

My ISP requires a http login. I can use the iPad fine if I am logged in on a PC connected to the same wifi network, but if I login on safari on my ipad, the connection drops after some time.. any workaround?

My ISP requires a http login. I can use the iPad fine if I am logged in on a PC connected to the same wifi network, but if I login on safari on my ipad, the connection drops after some time.. any workaround?

TJBUSMC1973 wrote:
The iPhone is working, as designed and advertised. In this case, the user failed to educate themselves properly, either by proper research or asking the right questions, before purchasing the device.
I understand that the OP failed to do research. But then, I wasn't replying to the OP. I was replying to Chris. I have Verizon. I can talk and use data at the same time with my Droid Maxx. Therefore, the problem is not just with the network. It would be technically possible for an iPhone to do that on Verizon/Sprint if Apple had chosen to use a different chip, such as the kind other phone manufacturers have elected to use.
Of course, this is probably all irrelevant to the OP's issue. It was merely a point of clarification, especially for those people who are used to being able to use both voice and data at the same time on Verizon. When they switch to an iPhone, they are often surprized at the limitation.
Best of luck.

Idle Oracle DB connection through ACE dropped after 1 hour

Hi folks,
I'm looking for some ideas how to troubleshoot a problem we're having with an Oracle App.
What we are finding is that when a request takes more than an hour for the Oracle DB to process the connection is being dropped.
When wireshark is used at DB server interface we see nothing for an hour and then a single packet RST,ACK with the source identified as the App Server.
We have an App server farm that is behind an ACE module that is in bridging mode. The DB server is on another VLAN so the path the traffic takes is from the App Svr through the ACE from the back to the frontside vlan, through the 6506's MSFC to be routed to the DB server.
Path like this:
Appserver|-->VL203-->|ACE|-->VL202-->|L3 Switch|-->VL200-->|DB Server
If we move the App server to Vlan 202 in front of the ACE the process carries on to completion (after 75 mins).
Is there anything in the ACE settings that could cause the connection to be dropped after an hour for traffic that should simply be being bridged through?
Any suggestions as to where to look next would be appreciated.
TIA
Zac

OK Gilles, I'll look at that in the morning. However, this is where it gets interesting.
We have DB servers on two other VLANs routed by the same switch. The connections to those DB servers don't get cut off after an hour (In the connection path I outlined swap VLAN 200 for VLAN 50 or VLAN 205) One of them is even behind the ACE in a different server farm.
Zac

Wi-Fi Connects then drops after 1min.

Similar Messages

Maybe you are looking for