WIC1-AM on Cisco 2801 Routers malfunctioning

Hi, I wish i will find a permanent solution for my issue which i face for last 8 months.
I had purchased 5 Cisco 2801 routers to setup in our network which involves
branch offices and the head office. The branch offices are in different cities. We purchased these rounters with one WIC1-AM for each router keeping in mind to have a backup dialup line once the main link is down. The problem area is here. We have tested the Routers with
configurations for backup line in our Head office, it worked fine. But when we send them to some of the branch offices, it started malfunctioning. The dialup WIC plays crazy with us.Sometimes works for 10 minutes, and disconnects. One of the branches, the WIC never got up!!.
Only two branches is properly working now with backup line in WIC-1AM. We have tried the same configurations on the affected routers too, but the result was not hopeful.
On the same telphone lines, we were (and still) using zyxel prestige 100 MH router and is working perfectly without any single problem to note!
Thanks for any light to shed on this!

Hello Mohamed,
can you post what you have configured on the router(s) that are working ok ? Also, which IOS version are you running on the routers that do not work ? Can you post the outbut of 'debug modem' ? This should give an indication of what is happening...
Regards,
GP

Similar Messages

  • What's wrong? Verify and compare Cisco 2901 config after loading old config from Cisco 2801

    Hi Cisco Community / Friends,
    I am new to this site though I have cisco account for many years. I am a CCNA ,I  passed my certification on January 2013 I seldom use and utilized my skills on networking becuase of my type of work. I am Project Eng'r working in a System integrator company . Anyway, I would like to ask assistance on the configurations of my Cisco router for this gov't projects.. Here's the situation.
    We have a new project for the VSAT Comm'n of  Coast Watch Station ,  The VSAT was installed 7 years ago. The VSAT was only used for a year by this Gov't agency because of  subscription issue. Now, they wants to revive and use their VSAT facilities for the Coast watch monitoring. Now, some of this routers are working up to now and for some site  are already defective so I need to replace the old 2801 router with a new equivalent model which is Cisco 2901. My plan was just to load the old config into the new Cisco 2901 router. However, after loading it to the new router, I am a little worried because I've got some errors received. I load the old config by copying the old files, edit it in notepad, and load the config using Secure CRT (terminal emulator). When I copy the old config of cisco 2801 to new router cisco 2901 , below are the command not recognized on Cisco 2901. What's wrong ? What are these commands for? 
    Appreciate your comments and help on this matter.. Thank You very much
    Note: I Attached the original config from Cisco 2801 and the other file is the config after I load the config file to Cisco 2901.
    (Errors see below)
    CWS_4_Pandami(config-erm)#mmi polling-interval 60
                                                           ^
    % Invalid input detected at '^' marker.
    CWS_4_Pandami(config-erm)#no mmi auto-configure
                                                           ^
    % Invalid input detected at '^' marker.
    CWS_4_Pandami(config-erm)#no mmi pvc
                                                           ^
    % Invalid input detected at '^' marker.
    CWS_4_Pandami(config-erm)#mmi snmp-timeout 180
                                                            ^
    % Invalid input detected at '^' marker.
    CWS_4_Pandami(config-if)#interface GigabitEthernet0/1
    CWS_4_Pandami(config-if)# description ===CWS4 SAT Modem===
    CWS_4_Pandami(config-if)# bandwidth 256
    CWS_4_Pandami(config-if)# ip address 192.168.42.1 255.255.255.0
    CWS_4_Pandami(config-if)# duplex auto
    CWS_4_Pandami(config-if)# speed auto
    CWS_4_Pandami(config-if)# priority-group 1
                                                        ^
    % Invalid input detected at '^' marker.
    CWS_4_Pandami(config)#access-list 100 permit ip any any dscp cs5
    CWS_4_Pandami(config)#priority-list 1 protocol ip high list 100
                                                    ^
    % Invalid input detected at '^' marker.

    Hi
    From Cisco's website:
    The Modem Management Interface (MMI) is software that enables auto-provisioning for the Cisco 827 routers. The MMI uses a fixed PVC to communicate with the Proxy Element (PE) residing on the digital subscriber line access multiplexer (DSLAM). Using MMI, the Cisco 827 router updates the running image and downloads the prescribed configuration using a configuration file or configuration values in a provisioning information database.
    The customer premise equipment (CPE) can be automatically configured using the Cisco DSL CPE download, but it can be configured only with the image provisioning feature.
    So because this is your device, you don't want to use MMI anyways.
    And "priority-list" is QoS. Probably that QoS-command is old and removed, because now QoS is configured using class-maps and policy-maps.

  • How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router

    Hello
    I'm looking for information on how to install 2 newly purchased cards  and keep running into dead links. The cards I bought are for a  CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco  router:
    vic3 2fxs/DID and a vic2 2fxo.
    I keep finding documents on how to  install these cards but all links are dead and leading to nowhere.
    http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
    The  2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco  2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco  router.
    NOTE: I've never installed these cards and am not sure if:
    Does my  ios support both of these cards?
    and which slots do I install those in the  router.
    I have 4 slots like this:
    slot 0: This slot only accepts VIC's   ***This could be used for the vic3 2fxs/DID card correct?
    slot 1: Nothing  written here  ****What can i install in this slot?
    slot 2: This slot only  accepts VIC's and WIC's  ***If I buy a WIC and install here which other slot can  i install my VIC2-2FXO card in ?
    slot 3: Nothing written here  ***What can i  install in this slot?
    Any chance someone can help me out with this.
    Thanks  very much

    Ok
    I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
    Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
    If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
    Thanks

  • Cisco 2801 (Voice Gateway + CUE)

    Hi there,
    I got two questions:
    1) When I try to login to Cisco 2801 I get the following lines: (I've already changed the default username and password!)
    Cisco Router and Security Device Manager (SDM) is installed on this device.
    This feature requires the one-time use of the username "cisco"
    with the password "cisco". The default username and password have a privilege level of 15.
    Please change these publicly known initial credentials using SDM or the IOS CLI.
    Here are the Cisco IOS commands.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want to use.
    For more information about SDM please follow the instructions in the QUICK START
    GUIDE for your router or go to http://www.cisco.com/go/sdm
    2) Is there any configuration example to configure CUE on Cisco 2801 (AIM Module)?
    Thanks.

    Hi there,
    1. The lines you reference are the default message of the day banner on the ISR routers. To remove the message, go into configuration mode and enter the command "no banner motd"
    2. Here's a sample configuration of configuring CME and CUE. The sample configuration should work on your 2801 ISR router. Feel free to give it a try and post here is you run into any issues or need clarification on anything.
    http://www.cisco.com/en/US/products/sw/voicesw/ps5520/products_configuration_example09186a008037f2a9.shtml
    Hope this helps.
    Regards,
    Michael.

  • Cisco 2801 Auto Attendant

    hello
    I have 2 Cisco 2801 running CME 4.3 and will be converter to SRST Routers, but they''ll have T1 card, because they used to has FXO card with 4 lines now they will have T1, but I wonder witch solution for auto attendant should I have for those routers especially the Unity Express.
    Thanks

    Before switching to CM, think twice, because you will gain a lot of complications, consts, and loose nice features and flexibility if you do that.

  • Cisco 2801 and VIC2-2E/M Card

    Hi Experts,
    One problem with my cisco 2801, when I have inserted the E&M card it is not supporting on the slot. The output of show diag is as attahced.
    IOS is : c2801-ipbase-mz.124-1c.bin
    Any help would be appreciated..
    Thanks,
    Hardik..

    You need a voice capable IOS feature set. The minimum is IP Voice for this card. Please see the following link for confirmation.
    http://www.cisco.com/en/US/products/hw/modules/ps5365/products_data_sheet0900aecd801c595e.html
    Hope this helps. If so, please rate the post.
    Brandon

  • Cisco prime infrastructure 1.3 makes every 15 minutes cpu high on cisco 800 routers

    I have an issue with cisco prime infrastructure 1.3 and cisco 880 routers, every 15 minutes the cpu goes to 100% on those routers, but I cannot find the job on the prime which is causing this, if I look in the job dashboard I have some jobs like sam_poller_22_15_getvpnpoller_27977292 that runs every 15 minutes (other jobs that I see CDBPoller_dmvpnPoller and CDBPoller_getvpnpoller)   , probably is it on of these jobs, but how can I stop it (job type : poller job, owner =system) and what are they doing?
    thanks for any assistance

    This is what i expected. I know many platform like 29xx/39xx or ISR's has known issues with Cisco Prime Infrastructure when it polls CISCO-LICENSE-MGMT-MIB, devices go high on CPU.
    You have to block clmgmtLicenseInfoEntry by creating a view on your 800 router by configuring snmp view.
    Following is the command/example:
    Step 1: Configure SNMP View:
    snmp-server view iso included
    snmp-server view   clmgmtLicenseInfoEntry excluded
    Link community string to SNMP View:
    snmp-server community view ro|rw
    Example per your configuration:
    snmp-server view PrimeInfra iso included
    snmp-server view PrimeInfra clmgmtLicenseInfoEntry excluded
    snmp-server community ArgSnmp view PrimeInfra RO ACLSNMP_RO
    OR you can try following on your Cisco PI:
    Manually update file below,
    Open the /opt/CSCOlumos/conf/sam/template.xml, modify the template id=20  (licensePoller)
    Update tag for value 600 to 86400 for all attrributes () of
    template id =20
    Old: 600
    New: 86400
    Some known bugs on such issues are :
    CSCug97914 and CSCuc72024
    Please check and let me know the updates.
    -Thanks
    Vinod
    **Rating Encourages contributors, and its really free. **

  • How to capture CISCO Switches / Routers CPU Utilization in MRTG

    Hi,
    I’m using CISCO Switches / Routers and wanted to capture the CPU Utilization of those devices in MRTG. Can anyone help me to get step by step information. Please.!

    Thanks Vinod..!
    I already have MRTG installed and monitoring link bandwidth utilization. Now, Wanted to capture the CPU utilization for those devices.  Can i know the configuration detail needs to be applied in MRTG / Routers or Switches.
    Provided URL don't have much detailed configuration needs to be done at both the side (MRTG / CISCO Devices). Please.
    Thanks,
    Tamil

  • Can I add these two VWIC2 modules on a Cisco 2801?

    Hello all,
    Can I add both of these modules on a Cisco 2801 running 12.4(3h)?
    VWIC2-2MFT-T1/E1
    and
    VWIC2-2MFT-G703 
    Thank you,
    Nadeem

    Thanks for the response, but it doesn't really address my question(s).
    Obviously, if I were buying memory for the old iMac, I would buy the same speed as the one already in it.  However, I am not buying memory, I already have this spare faster memory.   Let me split the question in two:
    1.  Will the faster memory work on the slower iMac?
    2.  Can the faster memory damage the slower iMac?

  • Obtaining DNS servers automatically on Cisco ADSL routers;" not static dns with command dns-server x.x.x.x" ?

    Obtaining DNS servers automatically on Cisco ADSL routers;" not static dns with command dns-server x.x.x.x" ?

    Ok Thank you Karsten

  • No service password recovery command on cisco 2801 router

    HI,
    we have a cisco 2801 router in class which has a disabled pasword recovery. We tried almost everything, we cannot get into ROMmon and the break sequence dosent work in any program (hyper terminal, putty, teraterm pro). We dont have any idea how to solve this problem.
    Here is the log from hyperterminal:
    System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2004 by cisco Systems, Inc.
    PLD version 0x10
    GIO ASIC version 0x127
    c2801 processor with 131072 Kbytes of main memory
    Main memory is configured to 64 bit mode with parity disabled
    Readonly ROMMON initialized
    PASSWORD RECOVERY FUNCTIONALITY IS DISABLED
    program load complete, entry point: 0x8000f000, size: 0xc100
    Initializing ATA monitor library.......
    program load complete, entry point: 0x8000f000, size: 0xc100
    Initializing ATA monitor library.......
    program load complete, entry point: 0x8000f000, size: 0xd49718
    Self decompressing the image : #################################################
    ######## [OK]
    --- TRIED BREAK SEQUENCE HERE but nothing happens ---
    Smart Init is enabled
    smart init is sizing iomem
      ID            MEMORY_REQ         TYPE
                    0X003AA110 public buffer pools
                    0X00211000 public particle pools
    0X0013          0X00035000 Card in slot 1
                    0X000021B8 Onboard USB
    If any of the above Memory Requirements are
    "UNKNOWN", you may be using an unsupported
    configuration or there is a software problem and
    system operation may be compromised.
    Allocating additional 7692663 bytes to IO Memory.
    PMem allocated: 117440512 bytes; IOMem allocated: 16777216 bytes
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, 2801 Software (C2801-IPBASE-M), Version 12.4(1c), RELEASE SO
    FTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2005 by Cisco Systems, Inc.
    Compiled Wed 26-Oct-05 08:42 by evmiller
    Image text-base: 0x6007ECA0, data-base: 0x61480000 
    --- TRIED BREAK SEQUENCE HERE but nothing happens too ---
    Port Statistics for unclassified packets is not turned on.
    Cisco 2801 (revision 6.0) with 114688K/16384K bytes of memory.
    Processor board ID FCZ102422KK
    2 FastEthernet interfaces
    2 Low-speed serial(sync/async) interfaces
    DRAM configuration is 64 bits wide with parity disabled.
    191K bytes of NVRAM.
    62720K bytes of ATA CompactFlash (Read/Write)
    Press RETURN to get started!
    Thanks for help!

    I usually suffer from the same issue, but what works for me everytime is the other method that simulates break sequence. Can't find the documentation for it but this is how it goes:
    Set the serial connection as follows in Putty:
    Baud rate 1200
    1 stop bit
    8 data bits
    no parity
    no flow control
    Turn off your router, then turn it back on and immediately press the spacebar for about 10-15 seconds. All you'll see is giberish. After that reset your console connection settings to the usual 9600 baud rate, and you'll find yourself in rommon mode.

  • Hi, I need your help.. I'm telecommunication technician, in my job we have CISCO 10008 routers, there's connected to DC Power b

    Hi, I need your help..
    I'm telecommunication technician, in my job we have CISCO 10008 routers, there's connected to DC Power by DC PEM sources. There's powered by  -52Vdc, but there's a problem, sometimes occurs failures, ESR-HH-GE cards suddenly crashes, the FAIL led is on and that's yellow color, but it doesn't works. We replace cards for this cases, and the service is OK, but this occurs again in the same slot or different slots, each 2 or 3 months aprox., or maybe one. Thanks for your help.

    Duplicate posts.   
    Go here:  http://supportforums.cisco.com/discussion/12185941/hi-i-need-your-help-im-telecommunication-technician-my-job-we-have-cisco-10008

  • Cisco 2801 Question

    I'm trying to open a port in a Cisco 2801, the port 3001 to give internet access for a cisco switch which IP is 172.16.8.40
    thanks in advance
    cisco 2801 config
    match access-group 110
    class-map type inspect match-all vpn-traffic
     match access-group 111
    policy-map type inspect priv-pub-pmap
     class type inspect all-private
      inspect
     class class-default
      drop
    policy-map type inspect pub-priv-pmap
     class type inspect vpn-traffic
      inspect
     class class-default
      drop
    zone security private
    zone security public
    zone-pair security priv-pub source private destination public
     service-policy type inspect priv-pub-pmap
    zone-pair security pub-priv source public destination private
     service-policy type inspect pub-priv-pmap
    crypto isakmp policy 1
     encr aes 256
     authentication pre-share
     group 2
     lifetime 84600
    crypto isakmp policy 5
     encr 3des
     hash md5
     authentication pre-share
     group 2
     lifetime 84600
    crypto isakmp client configuration group BFvpn
     key vPnBr1TT@ny9687!
     dns 192.168.2.10
     pool vpn_ip
     acl remotevpn
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set aes-256-sha esp-aes 256 esp-sha-hmac
    crypto dynamic-map vpn 65535
     set transform-set ESP-3DES-MD5
    crypto map vpn client authentication list AAA-VPN
    crypto map vpn isakmp authorization list AAA-VPN
    crypto map vpn client configuration address respond
    crypto map vpn 65535 ipsec-isakmp dynamic vpn
    interface FastEthernet0/0
     ip address 75.150.67.105 255.255.255.252
     no ip redirects
     no ip unreachables
     no ip proxy-arp
     ip nat outside
     ip virtual-reassembly in
     zone-member security public
     duplex auto
     speed auto
     crypto map vpn
    interface FastEthernet0/1
     ip address 172.16.250.1 255.255.255.252
     no ip redirects
     no ip unreachables
     no ip proxy-arp
     ip nat inside
     ip virtual-reassembly in
     zone-member security private
     speed 100
     full-duplex
    interface FastEthernet0/3/0
     switchport mode trunk
     no ip address
    interface FastEthernet0/3/1
     no ip address
    interface FastEthernet0/3/2
     no ip address
    interface FastEthernet0/3/3
     no ip address
    interface Vlan1
     no ip address
    interface Vlan413
     ip address 170.163.128.202 255.255.255.252
     no ip redirects
     no ip unreachables
     no ip proxy-arp
     ip nat outside
     ip virtual-reassembly in
     zone-member security public
    router eigrp 1
     network 172.16.0.0
    ip local policy route-map LocalPBR
    ip local pool vpn_ip 172.16.251.10 172.16.251.20
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    ip nat inside source static tcp 172.16.8.40 3001 172.16.250.1 3001
    ip nat inside source route-map NAT-HFC interface FastEthernet0/0 overload
    ip nat inside source route-map NAT-OPT interface Vlan413 overload
    ip route 0.0.0.0 0.0.0.0 75.150.67.106 track 3
    ip route 0.0.0.0 0.0.0.0 170.163.128.201 5
    ip access-list standard remotevpn
     permit 172.16.0.0 0.15.255.255
    ip sla 1
     icmp-echo 75.150.67.106 source-interface FastEthernet0/0
     frequency 30
    ip sla schedule 1 life forever start-time now
    ip sla 2
     icmp-echo 170.163.128.201 source-interface Vlan413
     frequency 30
    ip sla schedule 2 life forever start-time now
    access-list 1 permit 170.163.0.0 0.0.255.255
    access-list 1 remark for Telnet & SNMP Restrictions
    access-list 1 permit 172.16.8.0 0.0.3.255
    access-list 7 permit 172.16.8.40
    access-list 7 permit 172.16.8.41
    access-list 7 permit 172.16.8.42
    access-list 7 permit 172.16.8.43
    access-list 10 permit 75.150.67.105
    access-list 20 permit 170.163.128.202
    access-list 102 deny   ip any 10.0.0.0 0.255.255.255
    access-list 102 deny   ip any 172.16.0.0 0.15.255.255
    access-list 102 deny   ip any 192.168.0.0 0.0.255.255
    access-list 102 permit ip 172.16.0.0 0.0.15.255 any
    access-list 102 permit ip 172.16.0.0 0.15.255.255 any
    access-list 110 permit ip any any
    access-list 111 permit ip 172.16.251.0 0.0.0.255 172.16.0.0 0.15.255.255
    access-list 111 deny   ip any any
    route-map LocalPBR permit 10
     match ip address 10
     set ip default next-hop 75.150.67.106
    route-map LocalPBR permit 20
     match ip address 20
     set ip default next-hop 170.163.128.201
    route-map NAT-HFC permit 10
     match ip address 102
     match interface FastEthernet0/0
    route-map NAT-OPT permit 10
     match ip address 102
     match interface Vlan413
    snmp-server community chimenet#3000 RO 1
    snmp-server enable traps tty
    tacacs-server host 170.163.248.63
    tacacs-server host 170.163.248.64
    tacacs-server directed-request
    tacacs-server key 7 06050728414B071C1154405B5C54

    Hello Jherrera,
    Trust you are doing great.
    Could you please additionally configure "ip nat outside" under interface Fastethernet 0/1 and "ip nat inside" under interface vlan 413 and interface fa 0/0 and check if the its working.
    Regards,
    Mohit 
    **Please rate if you find this post helpfull

  • VPN between RV042 and Cisco 2801

    HI
    Kindly help me out. I'm configuring a p2p vpn between a cisco 2801 with IOS 12.3 and a linksys RV042. I'm getting following error on Linksys and Cisco respectively.
    [Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
    Dec 19 02:40:42 2011
         VPN Log
        Received informational payload, type NO_PROPOSAL_CHOSEN
    dst             src             state               conn-id     slot    status
    x.x.x.x       x.x.x.x   MM_NO_STATE          0        0       ACTIVE
    Below are my config:
    Linksys RV042:
    Keying Mode: IKE with Preshared Key
    Phase1 DH Group: Group2
    Phase1 Encryption: 3DES
    Phase1 Authentication: MD5
    Phase1 SA Life Time: 28800
    Perfect forward secrecy : enabled
    Phase2 DH Group: Group2
    Phase2 Encryption: 3DES
    Phase2 Authentication: MD5
    Phase2 SA Life Time: 28800
    Preshared Key: xxxxxx
    Cisco 2801:
    crypto isakmp policy 11
    encr 3des
    authentication pre-share
    group 2
    lifetime 28800
    crypto isakmp key xxxxxx address xxxxxx
    no crypto isakmp ccm
    crypto ipsec transform-set STRONGER esp-3des esp-md5-hmac
    crypto map myvpn 10 ipsec-isakmp
    set peer xxxxxx
    set transform-set STRONGER
    set pfs group2
    match address 103
    interface FastEthernet0/0
    ip address 10.0.0.56 255.255.255.0
    ip nat inside
    ip virtual-reassembly
    no ip route-cache
    duplex auto
    speed auto
    no mop enabled
    interface FastEthernet0/1
    ip address xxxx xxxx
    ip nat outside
    ip virtual-reassembly
    no ip route-cache
    duplex auto
    speed auto
    crypto map myvpn
    ip nat pool branch xxxxxx xxxxx netmask 255.255.255.240
    ip nat inside source route-map nonat pool branch overload
    access-list 103 permit ip 10.0.0.0 0.0.0.255 192.168.2.0 0.0.0.255
    access-list 110 deny   ip 10.0.0.0 0.0.0.255 192.168.2.0 0.0.0.255
    access-list 110 permit ip 10.0.0.0 0.0.0.255 any
    snmp-server community public RO
    route-map nonat permit 10
    match ip address 110
    Rgards
    SAM

    Hi,
    It looks like you are using the default hash for the crypto isakmp policy and that your connection is failing on the phase 1 negotiation.  The default hash on the crypto isakmp policy is sha.  On the 2801 try adding hash md5.
    crypto isakmp policy 11
    encr 3des
    hash md5
    authentication pre-share
    group 2
    lifetime 28800
    Let me know if that helps.
    Thank you,
    Jason NIckle

  • Manage Cisco ISR routers as one device

    I'm looking for a tool that allows me to manage two Cisco ISR routers (2911) as one device ("cluster" device or "virtual" device).
    Both routers are connected directly to the internet and are using HSRP to perform a function of the virtual default gateway for LAN devices.
    What about Cisco ASA in Active/Active or Active/Passive Failover mode?
    Thanks,
    Jernej

    No, this is not currently possible.  The devices need to be managed using their individual IP addresses (i.e. not the virtual IP of HSRP).  You'll generally want to do that for the time being since both devices will have their own CPU, memory, buffer, etc. characteristics.

Maybe you are looking for