Widescreen blur line problem

Hey all, new to the forums and quite new to final cut pro aswell.
However i have a problem with the widescreen filter so i was wondering if any of you could help a noob out.
Every time i add the widescreen filter to my footage there are these annoying little blur lines visible just above the black bars.
I rendered everything and then exported it to a quicktime movie to see if it was just a rendering or playback problem but they're still visible after being exported.
They aren't clearly visible upon first glance but they are there, and i notice them every time which makes them extremely annoying.
I'm not very technical with Final Cut yet so apologies if my query sounds a little confusing but any help in getting rid of these little blur lines would be much appreciated.

In the Widescreen filter settings, try changing the footage offset by small increments one way or the other. Sometimes this can help define that widescreen line.
rh

Similar Messages

Why does my screen makes grey stripes like blurred lines over my screen?

Could any one help me find out why my iPad makes grey blurred lines?

It could be either a physical defect or a problem with the software. I remember I had a similar issue with my iPad 4, a random blue line showed up on my screen. I brought it into the Apple Store to see if they would exchange it for a new one and they were happy to do so.

Intermittent noisy line problem

Hi. Just about tearing my hair out over a line problem which has been giving trouble on & off for over 6 months. The line becomes very noisy from time to time, depending on weather it seems. We have had similar problems ever since moving here 13 years ago - the line runs overhead through woodland for about 4km to the exchange - and each time it is a corroded wire due to water penetration somewhere along the route.
This time the engineer cannot locate the fault. He agreed there was noise but the equipment he had could not locate where it was. He advised calling another engineer when it was bad and hopefully he would be able to locate it. However, I have just noticed that BT has charged me £127 for the visit, even though there was no suggestion that the fault lay with the internal wiring or equipment - heck, I even gave the guy a cuppa tea!
Any advice on (a) getting the charge reversed and (b) getting the fault sorted. Sometimes the line is so bad I have to resort to mobile, and the broadband speed can drop to a few hundred kbps. Grrrrrr.
Solved!
Go to Solution.

Try contacting the board mods
At [email protected] with a link to this post and your bt account no and phone no they will reply within a few days and are great at sorting these sort of problems
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Why is blurred lines removed from itunes

why is blurred lines removed from Robin Thicke's Album?

Interesting, looks like some sort of weird glitch in the iTunes Store. Track 10 is showing up twice, and track 1 is not showing up at all. I would venture to guess that it would download correctly if someone actually purchased the album, but I won't be the one to test that theory. Hopefully they get it resolved soon.
Here is what the OP is talking about:

I faced white screen with gray line problem on startup. How to fix it?

I faced white screen with gray line problem on startup. How to fix it?

Hi vikashjha,
Thanks for visiting Apple Support Communities.
You may find some of the troubleshooting steps in this article helpful:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/HT1573
Cheers,
Jeremy

Counting lines problem. Please help!!

Hi all,
I just have a small problem i cannot resolve, here it is: I read through a file and i like to count the lines of the file there is before a special word.
E.g
My file contains:
"hi
how are you
my name is john
and i live
britain"
I'd like to count how much lines there are in the file before the word LIVE ==> result would be 4.
I proceed with StreamTokenizer, but i don't knor how to specify the word. Here is my code:
     try {FileReader fr = new FileReader("test2.dat");
               BufferedReader br = new BufferedReader(fr);
               StreamTokenizer stk = new StreamTokenizer(br);
               do {
               n = stk.nextToken();
               li = stk.lineno();
               if (n == stk.TT_NUMBER) {
                    n = stk.nextToken();
               if (n == stk.TT_EOL) {
                    li++;
                    n = stk.nextToken();
               if (n == stk.TT_WORD) {
                    String str = stk.sval;
                    if ("entier".equals(str)) {
                         System.out.println(li);
                    else {
                         n = stk.nextToken();
               while (??????????????);
I want here to specify the word "entier" but how to do this??
Thanks very much for your precious help....

A: Counting lines problem. Please help!!

Use LineNumberReader, which counts lines for you. Here's a complete program in 16 lines:
import java.io.*;
public class test4 {
public static void main(String[] argv) {
    if (argv.length < 2) { System.err.println("no arg"); System.exit(0); }
    try {
      LineNumberReader in = new LineNumberReader(new FileReader(argv[1]));
      String line;
      while((line = in.readLine()) != null)
        if (line.indexOf(argv[0]) != -1)
          System.out.println("Found match at line " + in.getLineNumber());
    } catch (IOException e) {
      e.printStackTrace();
}If you want case insensitivity, you can make both lines lower-case before searching. Or you can use regular expressions.

Blue Shapes Occuring Randomly(Not Line Problem)

Blue Shapes Occuring Randomly(Not Line Problem)
I have just purchased my powerbook 1.67 1440*960. I started to see blue shapes around the windows that I move and around many things that move on the sceen after the first week of my purchase. At first I thought this was a configuration problem but it seems more like an hardware problem although the hardware test found all the devices successfull.
In addition, when I installed call of duty, the blue shapes occur very fast and randomly everywhere on the screen making it impossible to play the game.
You could have a look at the picture to see how disturbing they are.
http://homepage.mac.com/altan.sursal/FileSharing1.html
Does anybody have an idea why such blue shapes occur?
Thanks All

Most likely one of the reasons your not getting any answers is that you need to post a link to the page. Sifting through all that code without the ability to see the actual page makes the going slow.
Post a link to the page and I'm sure help will be on the way.
Gary

I want a free upgrade to Intel To fix the line problem

i have the line problem and the new intel MacBook has (i think) a bigger screen but less pizels than the old one so i guessing it will not have the line problem and i want a free upgrade.
do you think apple will do it?

Update: After 2 hours on the freeking on with apple care... i got nothing, every person i talked to acted like they have never even heard of the line problem. So yeah there was no way of me getting a MacBook.
They did say i could send my PB in to see if i could get the screen fixed. I really dont want to because i cant live a long long time with out my powerbook and then get it back weeks later and NOTHING fixed.
BTW - it was a little funny with every one using the term MacBook, They would mess it up and stuff and even when one of the person was talking about it i was thinking "Mac Book" as in a book the people look in to look up specs and problems and stuff.
Also one person said they have allready sold over 100,000 and im like "wow they only went on sale a few hours ago and its not shipping for another month.

Hp a1230n reboots and vertical lines problem

Hi
I'm completely new so this may even be in the wrong place but yeah basically what it says in the title. It keeps rebooting on its own. Sometimes the screen will only show vertical lines that are the same color as what was on the screen. I've scanned it for viruses with first Macfee and then Avast and they've said its clear, and it runs fine other than the rebooting and lines problem.
Thank You

Hello mnstrzero00,
You’re having problem with the computer rebooting.
Your problem could be software problem of hardware.
How long has this problem been happening?
If it has not been happening for very long you might just try a system restore back to before the problem started. This should correct the problem without affecting any of your files.
Here is a link to do a restore.
Before the restore run the following command in command prompt. SFC /scannow.
Click start -> click run -> type CMD -> hit enter.
This will check system files and correct them if it can.
Also to make sure that it is not hardware.
Turn off the computer and the n turn back on, at startup tap the F2 and run hardware diagnostics.
Let me know if this helps.

Satellite 3000 screen vertical line problem

my laptop is Satellite 3000 , it got vertical line problem now, i wanna use a outside CRT screen to replace the current damaged LED screen.
I have tried to use FN-F5 swap key, but it is still doesn't work, i tried to log in the system to check it, (the system (windows xp) is normal), but i can't see anything because the screen is black, it won't get in the system even if i connected it in to the LAN, because the laptop network function configuration is not allow connect with internet,( i did ghost before it completely damaged), the question is :
1, do i need to configure something so as to it can use outside screen in windows XP system? or just use FN-F5 swap key?
2, how will i do next step if i wanna use the outside screen ?
thx a lot

Hello
If the notebook is preinstalled with all Toshiba designed tools and utilities FN+F5 key combination should work. Of course the external monitor should be connected properly.
If you are missing some tools FN+F5 key combination will not work.
What I want to know is what happens exactly when you use FN+F5 key combination? Stays the LCD screen black or switch to the right picture again? As far as I know if you use FN+F5 key combination and LCD on the notebook stays black that means the signal is send to external device but if the monitor is not connected properly or there is some contact problem you will not see the content on external monitor.
Believe me it is not easy to say what is wrong there but if possible try to test it with different monitors. Satellite 3000 is pretty old notebook model and maybe is RGB port defective.

MBP Display Lines Problem

Hey everyone, I just bought a MBP 15' 2.2Ghz last wednesday and am now seeing a display line problem. I see a green dotted line that extends from the top of the screen to the bottom approximately 2 inches from the right of the screen. The color of the line seems to change slightly depending on whats on the screen. For instance, I had the ladybug wallpaper and the line was almost complete all the way down (stil dotted with a missing section) and the color was bright green. With a different wallpaper that had a night sky and a green figure, the line flickered green/blue in the night sky area and steady green in the green part. My question is whether this is software or hardware related. I read many many other posts and many had display line problems but not the same as this one. Should I get this repaired? Is there anything I can do to fix this? Thanks

Hey man, sorry to heard you have a display problem too. I have a line at the bottom of my display which extends across horizontally. Fortunately, its just a clear, bleached looking line which I can mask with the dock. I dont think I could tolerate the line in which you have described.
I would bring it to the apple store that you bought it from and have one of the apple guys check it out. I would demand a replacement. They will try to repair it. You shouldnt be repairing a defective purchase.
I am on my 2nd MBP. My first was kernal panicing all the time. I got it to KP in the store and he immediately offered a replacement. Apple care is pretty good, so dont be afraid to bring it in and demand a replacement.
Better luck with your next one!

Blur Tool Problem - Random Lines (Adobe CC 2014.2.1 Release)

Hi,
I'm hoping that I haven't ticked some obscure option, but I have been using the Blur Tool in Photoshop CC for a while and after the most recent update have had issues with it - basically, when I try to use it to blur a specific area, it randomly goes all over the place (as if I'd grabbed the mouse and moved it rapidly in a random direction). Obviously if I can't use the blur tool with precision (well, any tool really!) it makes it hard to work!
Some interesting notes / observations:
The sharpen tool works perfectly - only sharpens where I point it, which makes me think that it's not an issue with my mouse. No other tools I use have the issue either - only the blur tool!!
I have no other pointing devices plugged in (I had a pen tablet plugged in - long story, prefer the mouse over the tablet :-)) so it's not some other pointing device making noise.
Has anyone else encountered this problem, and if so, how did you resolve it?
Thanks - blurring and then going into the layer to delete the random lines of blur is getting tiresome - and it's not very precise either.
Cheers,
Terence.

Check out this other thread I started
http://feedback.photoshop.com/photoshop_family/topics/using-text-tool-freezes-photoshop-cc -2014-2-0-20140926-r-236-x64-release?utm_source=notification&utm_medium=email&utm_campaign =new_reply&utm_content=reply_button&reply[id]=14914157#reply_14914157
There it's help there. I've not totally solved my problem but others seemed to have.
Richard

"Drop shadow" creates a line - problem

Hi,
I'm in process of making a map (17x22 inches) and I encountered quite disturbing problem with "drop shadow" effect.
I tried to drop shadow on an object 12x18 inches size with those parameters:
And I got nice result on all of the shape, except the lower part, which give me a line. Like cutting through the shadow thing:
I will add that object is on the layer alone and nothing is interacting with it.
At first I thought that maybe this is display problem, not the shadow itself, so I zoomed in and out, but nothing changed. Then I made sure that all anchors are connected one to another - I'm sure the object IS closed. I tried to manipulated anchors points, changed shape of the object a bit, add, remove some anchors, changed shadows parameters - nothing made any difference in how the shadow looks like. Any ideas?
Thanks,
Ania

Your file helped me a lot, Larry. But I still think I got some nasty bug in my original file and I will explain You, why I still think that.
When I opened Your file the shadow was flawless. But when I copied the object You sent me to my old file to replace it, the line appeared in the exactly same place. I thought that maybe, in some weird way other layers and objects mess with that effect but no... When I started to copied objects FROM my old file to YOUR new fixed file, shadow remained nice. So it seems that my old file is somehow corrupted (calculating gaussian blur seems to be the problem there), on the new file - where ALL parameters are the same, all the layers and shapes are the same as in old file except for Your "Drop Shadow" effect - there is NO such problem. Look:
My old file after copying Yours fixed object (line again!):
And here Your file with all the rest of my graphics:
So thanks to You, I may keep on working on my project but the mystery remains.
Cheers,
Ania

Blurred lines when using the stroke tool

Im trying to draw frames with feathered corners using strokes, its supposed to be a solid black line 2px thick it works sometimes but not others. What I end up with is a blurred edge, almost like it's using a spray which is not at all what I want, have tried changing various settings but its still the same.
Anyone any ideas please? It's driving me mad..
Thanks!

Yes, I was using the marquee tool to create the rectangular shapes then using the stroke tool. I took feathered setting off and that resolved the problem.
But...
How do I create rectangular shapres with rounded edges, then use the stroke tool?
I've changed the colour settings so it's not being 'filled' but when I try to use stroke it's now greyed out.
All I am trying to achieve is a rectangular shape with rounded edges with a black outline.
I thought it would be simple ;)

Mini-DVI to Video adapter + Widescreen CRT Television problem...

The problem is that in the resolution list in Display-tab for the second display, which is PAL TV, have no resolutions for WIDESCREEN TV. Only resolutions are 640x480, 720x480, 720x576, 800x600 and 1024x768.
Is this a OS related or is there different adapters to iMac 24 and iMac 20? The adapter which I now have is lent from my friend and he have iMac 20.
How this even can be an issue to MAC, because this could be done easily on PC. I just got my first Mac and I love it but this kind of problems I even couldn't imagine.

My 27" flat screen TV added some 1220x720 selections to choose from. Go to the "NTSC/PAL" display perference panel and click the "Detect Displays."
From experence I have never been able to really use the TV as a true second display. Although it really does work quite well for showing DVD movie's, Home movie's, iPhoto slideshows, MS Word PowerPoint or anything FrontRow.
For quicker access to the Display Preferences check the "Show displays in menu bar" This places a display icon on the menu bar for one click access to resolution list and preferences for both displays.

Widescreen blur line problem

Similar Messages

Maybe you are looking for