Width of my animation on iphone android

hello i create an animation with width 680px
http://5.153.20.101/~com3web/com3elles.net/animation/com3elles.html
desktop and tablette look cool but in iphone and android device (in portrait)
the stage is rezize always ... but in device we have space ....
how to use whole width of device
regards

Hi, micker-
You should take a look at this forum post, which talks about the same issue. You'll want to set your viewport meta tag according to the answer to this post.
http://forums.adobe.com/message/5767975#5767975
Hope that helps!
-Elaine

Similar Messages

Weak iphone/android Wifi signal in rooms, APs in hallway

Hi...
I am struggling with weak signal coverage inside rooms where APs are hung on the outer walls of the rooms i.e. on the hallway, one the sides, not on the cieling. Laptops work fine but mobile devices (iphones, androids, ipads) suffer the most. The hallaway is approximately 30m long, having 4 large rooms, two on either side of the hallway. The walls are made up of cinder blocks with concrete pillars. We have installed 4 2602 APsin the hallway, each with 4 external antennas, in an alternate fashion, i.e. first AP on the left side of the hallway, second on the right, third again on the left, fouth on the right again. The APs are approximately 4m apart.
We are using
WLC 5508 7.4.100.0
Cisco 2602 APs with 4 external antennas
I have read the Cisco document of Best practices for Apple devices and enabled all 'n' data rates. That helped a little bit but I know we can get better coverage. I am suspecting that RRM is reducing the Tx power levels since the APs are all in the line of site.
I have to admit that a precise site survey was not performed but I hope to get some advice on tweaking the Tx levels in my scenario.
I am attaching 2 screen shots of the hallway APs (circled) in b/g/n and a/n showing the Transmit levels. I have tweaked one AP tx level only (circled, changed form 4 to 3 under a/n) but didnt get the time to see the results.
All help is appreciated

Thanks for the replies,
Leo,
I have tried to convince our people to place the APs inside, but they rejected this based on health concerns. I tried to dig up something from the internet to alleviate their fears but was not successful. The view of four antennas is what scares them most. Maybe I will remove the antennas and then try to convince them again.
Scott,
You have mentioned to position the external antennas in a vertical fashion. We have 4 per AP. Shall I point all the four in vertical upward direction or the top two upwards and the bottom two downwards? Just to remind you again that our APs are not mounted on the ceiling but on the side walls of the hallway.
I will force the Tx levels to 2 on all the 4 APs and hope interference will not degrade performance further.
Thanks again

Building SAP applications for iPhone, Android etc.

Hi All,
We have a requirement for building SAP online and offline applications for iPhone, Android, Windows phone. These applications would interface with SAP backend (ERP) for fetching data or for executing simple tasks like approvals etc.
We have developed thin client (online) applications using Webdynpro Java for Blackberry users. These applications are browser based applications (deployed on SAP Netweaver WAS) and are accessed through Blackberry browser. What I am not sure is whether the same approach/technology like Webdynpro for Java would work for handhelds like iPhone, Android and Windows phones.
Secondly whether vendors (like Apple) of iPhones, Android etc. provide specific connectors or frameworks for building SAP online/offline applications (or in other words what would be the mechanism for integrating iPhones, Android with SAP)
Lastly how (technology, architecture etc.) are SAP thick client or offline applications built for iPhone, Android etc.
Any pointers would be of great help.
Thanks & Regards,
Suresh

Hi Philipp,
Thanks for your quick response. When you say integrating with "Integrating Custom Client with DOE", do you mean the usage of SAP Mobile Infrastructure (now know SAP NetWeaver Mobile).
We are mainly looking at building online (thin client) applications and also parallely at building offline or thick client applications but that is second in priority.
What we have done so far
We have developed thin client (online) applications using Webdynpro Java (which interface with SAP backend systems)
for Blackberry users. These applications are browser based applications and are accessed through Blackberry browser. We are looking at similarly building applications for iPhone, Android and Windows phones probably using the same technology like Webdynpro Java. But we are not sure how well it would work on iPhone, Android etc. Also we were exploring to see if these vendors (iPhone, Android) provide some sort of connectors or framework for quickly developing and deploying SAP mobile thin client applications.
Please note that we are aware that using webservices in one generic approach.
Once again thank you very much for your response.
Regards,
Suresh

Accessing iPhone & Android Contacts list from AS3?

Hello,
Is it possible to get the contact list from the iPhone & Android agenda (mobile and SIM card) by using AS3?
Regards.
J. Pablo.

Hello,
I have to test it, but seems like it is almost the only reference to this issue.
I have also found few other things related to this link:
http://extensionsforair.com/extensions/contact-editor/
And another one related just to iOS:
https://code.google.com/p/as3iphone/source/browse/trunk/Classes/com/flashiphonedevelopment /address/IPhoneAddressBook.as
I have to test them, and I am very new, but thanks for your interest and help.
Regards.
J. Pablo.

Any tutorial to see the edge animation in iphone devices

any tutorial to see the edge animation in iphone devices

You can test some of the Edge samples here - http://www.adobe.com/devnet/edge-animate/articles/showcase-sample-files.html on iOS devices to see how they fair.
While its difficult to pinpoint what exactly you interested in seeing, if you google search edge samples you may zero in on some samples.
hth
Darrell

A few quick questions about publishing for iPhone/Android

I'm currently developing an iPhone/Android game in CS5 and I just have a few quick questions. If anyone can answer even one or two I'd really appreciate it
1- I'm developing using a 320 x 480 resolution for the iphone. When I tested it, the status bar on the top of the screen makes the edges disappear. How should I turn off the status bar? And if I can't what resolution should I use?
2- The performance is a little slow, and the game isn't very intense at all. What's a good way to improve performance?
3- For Android, what should I do for the resolution? Is there a standard resolution or do I have to have multiple resolutions for multiple devices?
4- Finally, is it worth getting the free trial of CS5.5 before I publish? Is there anything in there that will be a huge improvement over CS5?
All help is appreciated

1. Publish in fullscreen
2. Use bitmaps, cache all bitmaps, use minimized looping structure etc.
http://www.yeahbutisitflash.com/?p=986
3. Android: 480 * 800
4. Not that much, but you have GUI updates and have a GUI publishing screen for packager for iphone too.

HTTP Live streaming test in Flash Player, HTML5 player, iphone, android and other smart phones.

Hi,
Can anyone please tell me how can I play http live streaming from FMLE 3.2 to Flash player, iphone, ipdad, HTML5 player, Android and other devices?
I have tried my best to play live streaming usine FMLE 3.2 with help of "http://help.adobe.com/en_US/flashmediaserver/devguide/WSd391de4d9c7bd609-52e437a812a3725df a0-8000.html" but not able to play video using HTTP.
When I tried to play url- "http://localhost/hds-live/livepkgr/_definst_/liveevent/livestream.f4m" even in in Strobe Media Player it was showing "Buffering" that's it. But I can play same RTMP URL in Flash AS3 using the netstream very fine.
Now I want to test the livepkgr content via HTTP to Flash Player, HTML5 Player (on Web browser and smartphones), iphone and other devices.
Thanks
Best regards,
Sunil Kumar

Hi Sunil,
It's difficult to debug an issue when you don't have access to the machine and you can't see what's happening, so I request you to please have a little patience.
For playback just check the following steps and make sure if you have followed them :
1) Delete the streams folder and any .stream file in the livepkgr
2) Restart FMS
3) Make sure you have a crossdomain.xml under root_install/webroot
4) Publish a stream from FMLE as 'livestream?adbe-live-event=liveevent'
5) Use this player to playback the stream : http://osmf.org/dev/2.0gm/StrobeMediaPlayback.html?src=http://<your-ip>/hds-live/livepkgr/_definst_/liveevent/livestream.f4m
If there is no playback, here are some checks you can do :
1) Request for the http://<your-ip>/hds-live/livepkgr/_definst_/liveevent/livestream.f4m in your browser. You should receive an xml that looks something like this :
<?xml version="1.0" encoding="UTF-8" ?>
     <manifest xmlns="http://ns.adobe.com/f4m/1.0">
          <id>livepkgr/events/_definst_/liveevent</id>
                  <mimeType />
          <streamType>live</streamType>
          <duration>0</duration>
          <bootstrapInfo profile="named" url="../../../streams/livepkgr/events/_definst_/liveevent/livestream.bootstrap" id="bootstrap7158" />
          <media streamId="livestream" url="../../../streams/livepkgr/events/_definst_/liveevent/livestream" bootstrapInfoId="bootstrap7158">
                      <metadata>AgAKb25NZXRhRGF0YQgAAAAAAAhkdXJhdGlvbgBAJUUeuFHrhQAFd2lkdGgAQHQAAAAAAA=</m etadata>
            </media>
</manifest>
2) Check the access log under Apache to see if the .f4m, .bootstrap and Frag files have been requested and delivered. If a particular entry has a status code of 200 then the file has been served by FMS. You can confirm the same on the client side using a software like fiddler.
Coming to the player issue, a playback of *f4v via the vod directive is a progressive download, whereas playback of an *f4m file via hds-vod is HTTP streaming.
I have personally used Spark VideoPlayer and hence suggested the same.
You need to add a component like :
<s:VideoPlayer width="100%" height="30%" chromeColor="#CCCCCC" color="#000000"
                 fontSize="12"
                 source="http://<your-ip>/hds-live/livepkgr/_definst_/liveevent/livestream.f4m"
                    symbolColor="#000000"/>
Let me know if any of these suggestions help.
Thanks,
Apurva

Pdf file, How do I fit by width in landscap mode on iphone?

In landscap mode, pdf file show full page and I have to zoom in everytime. I want to fit width when put in landscap. How to??

Doesn't seem to be a setting for this in iBooks 3.1 (tested on both an iPad [3rd Gen] and iPhone 4S both w/iOS 6.1.3)
However, a little experimentation reveals -- it depends on the PDF.
If the PDF is text (I used 'PowerShell in Action' - a programming book) you can use the same method as Mobile Safari - Double tap in the text and that section expands to fit the width of the screen in landscape or portrait. Centered on where you tapped in the text.
If the PDF is a single image - like a PDF comic book (I used a volume of 'Girl Genius'), it appears that the double tap to expand doesn't work. If the PDF is already full width, a double tap does appear to shrink it back to full page view.
Unfortunately, this seems to be on a per page basis. When you flip to the next/previous page it goes back to full page view.
Note: There are other PDF viewer apps/apps with PDF viewers built in that behave differently, more like you are looking for. Some are even free.
Hopefully Apple will improve this in the next version.
And, of course, the obligatory disclaimer - YMMV with different PDFs, versions of iBooks, and iOS and this is just a random comment on the Internet. Not warrantee expressed or implied. And my employer (which is not Apple) has no idea I just wrote this.

Big iPhone/Android Question

Hey guys, i am due for an annual upgrade pretty soon, however my actual upgrade for NE2 is in August, i was really debating to get the iphone when verizon gets it or the LG Ally phone. I hear go with a droid, what do you guys suggest??

lack of multi tasking on the iphone is not a verizon thing, its an apple thing
you can multitask on the iphone, with limited results.
it uses an app for that, and the apps that are running must be writtin to use the multi tasking app
texting and surfin on verizon network is limited on any phone
you temporarily lose your data connection when the text is sent or recieved.
you cannot talk and surf at the same time either, its a techonolgy thing, cdma does not do this
gsm does, lte will (i think)
multitasking is running 2 apps at the same time.
think of windows and running excell and word at the same time.
windows mobile does it, android does it, iphone is possible (if the software is written properly

Voice over WLAN - Cisco 2504 and iPhones/Androids

All:
I'm working on a solution for someone who already has a Cisco WLC 2504 running 7.6.100 and 2602i APs. They are running iPhones with a SIP application instead of purchasing Cisco 7925G phones. They are having issues when roaming to different APs.
Site survey is good. I also used a laptop with Net Surveyor on it - signal looks good. SNR is good. They used to have coverage issues as well but I got that taken care of for them. Only issue now is roaming.
WLAN SSID:
-Qos: Platinum
-FT-PSK and PSK enabled
802.11a/n/ac Radio:
-Client Roaming: -67dBm for RSSI threshold and -62dBm for scanning threshold.
-Disabled 6mbps and 9mbps and 12 mbps is set to mandatory. All others are supported
802.11b/g/n Radio:
-Client Roaming: -67dBm for RSSI threshold and -62dBm for scanning threshold.
-Disabled 1mbps - 12mbps. 18mbps set to mandatory. All others are supported
Switch to which WLC is connected:
-switch ports used to connect to the controller are set to trust CoS and ports to APs and uplinks are set to trust DSCP.
With these setting changes - I believe most everything else is default. I am confused about the following:
-Best practice link - http://www.cisco.com/c/en/us/td/docs/wireless/technology/vowlan/troubleshooting/vowlan_troubleshoot/2_Gen_Troubleshooting_Guidelines.html
Says to configure voice WLAN to use 802.11a. Issues with that: Some Android's could not connect AND the big one - I am not able to set Qos to use 802.1p for the SIP WLAN. It tells me to disable 802.11a and 802.11b. If I go into each radio on 'Network' tab and disable these - NOTHING can connect to any SSID. So unless I've misunderstood something - this is a contradiction in the best-practice link I posted above.
another question: If I enable FT-PSK and PSK - for devices that support FT-PSK (which i'm under the impression is 802.11r) will these devices use that and for devices that don't they'll use 'regular' PSK? How do I know if my client is connecting using PSK or FT-PSK as both are enabled on the same WLAN.
Again - only issue is roaming. I second or two of 'choppy' voice then everything is back to normal working as expected. Any ideas as to what else I can enable to get these iPhones to roam better - if this is even possible. Can iPhones roam using a SIP app with zero voice interruption? This is the equipment that they got and can't get anything else so I got to make the best of this. Perhaps I've already done that? Any ideas/suggestions are very much appreciated.

Hi
Before any other think I would like you to upgrade your WLC image to 7.6.130.0 & FUS to 1.9.0.0. FUS upgrade will require 30-40min downtime to your wireless.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/fus_rn_OL-31390-01.html
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn76mr03.html
It tells me to disable 802.11a and 802.11b. If I go into each radio on 'Network' tab and disable these - NOTHING can connect to any SSID. So unless I've misunderstood something - this is a contradiction in the best-practice link I posted above,
This simply says, you have to disable radio band before changing QoS profile values. Once you change those value you can re-enable the radio band. :)
If I enable FT-PSK and PSK - for devices that support FT-PSK (which i'm under the impression is 802.11r) will these devices use that and for devices that don't they'll use 'regular' PSK? How do I know if my client is connecting using PSK or FT-PSK as both are enabled on the same WLAN.
Read these 802.11r post & you will understand how 802.11r works. There are certain client devices does not like PSK & FT-PSK capability advertise on the same SSID & may have connectivity issues. But most of the clients like iPhone, iPads,etc will connect without any problems.
http://mrncciew.com/2014/09/06/cwsp-802-11r-ft-association/
http://mrncciew.com/2014/09/07/cwsp-802-11r-over-the-air-ft/
http://mrncciew.com/2014/09/08/cwsp-802-11r-over-the-ds-ft/
"show client detail <mac_address>" should indicate if client connected over FT-PSK or PSK.
HTH
Rasika
**** Pls rate all useful responses ****

Navigator transition animation more like android default background animation

Hi,
I'm building an mobile Air app for my tablet.
This app has multiple screens and the user will be navigating through them a lot.
I'm using the navigator push and pop views to accomodate this.
this works perfectly with all the default animations.
My problem is that i would like the animation to be more like the default android background animation.
and by that i mean that one you drag your finger over the screen the next 'view' already comes into the viewing area a little bit (and your current view disappears a little).
If you release your finger to early the view snaps back, if you swipe through you go to the next view.
With the current navigator transition it's an 'all or nothing' swipe, if i swipe i get the next (or previous) view but i don't have the option to drag my screen a little bit to see the first part of the screen i want to navigate to.
Does anyone know of a way to accomplish this with the navigator?
Or am i forced to abandon the navigator and write this transition logic by myself?
I hope i made myself clear, any help is much appreciated.
with kind regards,
Peter Bierman

AIR does not currently have an API to read this particular Android setting. To answer your question, Flex view transitions are independent of the Android system settings.
Jason San Jose
Software Engineer, Flex Mobile

Why Isn't My Weather App Animated in iPhone 4 with iOS 7?

Hi,
I had seen pictures and videos of the Weather App in iOS 7 animating (for example: lightning striking if there are thunderstorms or rain falling if it's raining). Mine is just a picture of clouds now, not moving.
Is there any setting I need to change to get the weather animated? Please note I have the iPhone 4 so it may not get this feature?
Thanks in Advance,
Suresh Balakrishnan.

Hi,
pls see the below mentioned youtube video, it's perfectly working on iPhone 4. please let me know if any setting is there?
Thanks in Advance,
Suresh Balakrishnan.

[SOLVED]Can't mount iPhone/Android devices.

Hi,
Since some update (can't tell exact update) I am unable to mount mobile devices on iOS or Android as a flash drive. It appears as "camera" in my "Available Devices" in KDE and when I try to open it with file manager, it appears blank.
In journalctl I can see the reason, but don't know how to fix it:
sep 11 12:32:14 laptop kernel: usb 1-1.2: new high-speed USB device number 11 using ehci-pci
sep 11 12:32:14 laptop mtp-probe[20038]: checking bus 1, device 11: "/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2"
sep 11 12:32:14 laptop mtp-probe[20038]: bus: 1, device: 11 was not an MTP device
sep 11 12:32:14 laptop kernel: ipheth 1-1.2:4.2: Apple iPhone USB Ethernet device attached
sep 11 12:32:14 laptop upowerd[2855]: usbmuxd_get_device_list: error opening socket!
sep 11 12:32:14 laptop colord[709]: Device added: sysfs-Apple_Inc.-iPhone
sep 11 12:32:14 laptop systemd[1]: Starting iOS USB Muxer...
-- Subject: Unit usbmuxd.service has begun with start-up
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Unit usbmuxd.service has begun starting up.
sep 11 12:32:14 laptop systemd[1]: Started iOS USB Muxer.
-- Subject: Unit usbmuxd.service has finished start-up
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Unit usbmuxd.service has finished starting up.
-- The start-up result is done.
sep 11 12:32:14 laptop usbmuxd[20052]: [12:32:14.302][3] usbmuxd v1.0.8 starting up
sep 11 12:32:14 laptop usbmuxd[20052]: [12:32:14.303][3] Successfully dropped privileges to 'usbmux'
sep 11 12:32:14 laptop usbmuxd[20052]: [12:32:14.311][3] Connecting to new device on location 0x1000b as ID 1
sep 11 12:32:14 laptop usbmuxd[20052]: [12:32:14.311][3] Initialization complete
sep 11 12:32:14 laptop usbmuxd[20052]: [12:32:14.312][3] Connected to v1.0 device 1 on location 0x1000b with serial number bda1b89b56ff882835c0790ebe27d9e74e163cec
sep 11 12:32:14 laptop systemd-sysctl[20064]: Duplicate assignment of kernel/sysrq in file '/usr/lib/sysctl.d/50-default.conf', ignoring.
sep 11 12:32:14 laptop systemd-sysctl[20065]: Duplicate assignment of kernel/sysrq in file '/usr/lib/sysctl.d/50-default.conf', ignoring.
sep 11 12:32:14 laptop systemd-udevd[20035]: renamed network interface eth0 to enp0s26u1u2c4i2
sep 11 12:32:14 laptop NetworkManager[389]: <warn> failed to allocate link cache: (-10) Operation not supported
sep 11 12:32:14 laptop NetworkManager[389]: <info> (enp0s26u1u2c4i2): carrier is OFF
sep 11 12:32:14 laptop NetworkManager[389]: <info> (enp0s26u1u2c4i2): new Ethernet device (driver: 'ipheth' ifindex: 27)
sep 11 12:32:14 laptop NetworkManager[389]: <info> (enp0s26u1u2c4i2): exported as /org/freedesktop/NetworkManager/Devices/5
sep 11 12:32:14 laptop NetworkManager[389]: <info> (enp0s26u1u2c4i2): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
sep 11 12:32:14 laptop NetworkManager[389]: <info> (enp0s26u1u2c4i2): bringing up device.
sep 11 12:32:14 laptop NetworkManager[389]: <info> (enp0s26u1u2c4i2): preparing device.
sep 11 12:32:14 laptop NetworkManager[389]: <info> (enp0s26u1u2c4i2): deactivating device (reason 'managed') [2]
sep 11 12:32:14 laptop NetworkManager[389]: <info> Added default wired connection 'Wired connection 3' for /sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1....26u1u2c4i2
sep 11 12:32:14 laptop kernel: IPv6: ADDRCONF(NETDEV_UP): enp0s26u1u2c4i2: link is not ready
sep 11 12:32:17 laptop kernel: traps: iphone-set-info[20040] general protection ip:7fd151259e86 sp:7fff6197fdf0 error:0 in libimobiledevice.so.4.0.1[7fd15114e000+1a000]
sep 11 12:32:17 laptop systemd-coredump[20067]: Process 20040 (iphone-set-info) dumped core.
-- Subject: Process 20040 (iphone-set-info) dumped core
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Documentation: man:core(5)
-- Process 20040 (iphone-set-info) crashed and dumped core.
-- This usually indicates a programming error in the crashing program and
-- should be reported to its vendor as a bug.
I've tried to mount iOS device with ifuse, but it didn't work either.
Any idea?
Thanks in advance.
Last edited by Zack7777 (2013-11-11 10:13:26)

Thanks for the answers.
ewaller wrote:That looks like it is trying to treat your iPhone as a network interface. Have you turned on USB tethering on your phone? What happens if you turn it off?
It's always like this, no matter if I turn on or off tethering.
mzneverdies, donniezazen,
Ok, this seems to work with android devices but not with iOS. Also when I run detect while my iPhone is plugged in, device list is empty:
$ mtp-detect
Unable to open ~/.mtpz-data for reading, MTPZ disabled.libmtp version: 1.1.6
Listing raw device(s)
No raw devices found.
Main goal is to return support of iOS.
Last edited by Zack7777 (2013-09-12 07:56:34)

Creating Help for Iphone/Android app

I need to create help for an iPhone and Android app using RoboHelp 10.
Which option do I choose for a New Project: Blank Project or Application Help?
And, which output do I choose under "File > Generate"? I see an option for "Native Mobile App." But, I'm not seeing a "Multiscreen HTML5" option.
Which file do I give the developer?
Thanks for your help!

That's a pretty big question and you haven't given us any clues such as which version of RoboHelp you are using and whether it is just this form of help that is new to you or help in general.
It doesn't really matter whether you choose Blank Project or Application Help as they are just starters with different default topics and you will be trashing them anyway. For now let's say start with Blank Project and create your topics. You do need to keep in mind they will be viewed on various devices. More about that later.
When that is done you start thinking about creating a suitable output. Multiscreen HTML5 is the output in RoboHelp 10. RoboHelp 11 was released today and that has a new output, Responsive HTML5. That is simpler, especially first time out. Both of those types are intended for use where they will be viewed via a browser, be that on a desktop or a mobile device.
It is not clear whether you want your company's app to access help in that way or whether the need is for the help to be an app in its own right. The latter adds another layer of learning. Essentially after creating an HTML5 output, you use the script to create an app. From the questions you ask, I suspect you will need developer assistance with that.
Start by viewing my page at http://www.grainge.org/pages/authoring/html5/html5.htm where you can download a project with information inside, include some ideas about how to write content.
See www.grainge.org for RoboHelp and Authoring tips
@petergrainge

Bbm for iphone,android makes bb user fools

Bbm for iphones,and androids were free with their normal data cost, but for blackberry users have to put bbm plan seperatly for messaging, it really sucks, its like wife charging her husband for sex but gives free sex to the whole city.......really wierd

And, everyone else pays for data as well... those on iOS and Android pay for data.
Sorry, your conclusion is not valid.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Width of my animation on iphone android

Similar Messages

Maybe you are looking for