Wierd problem, monitor no signal.

ok, this is a pretty wierd story...
I was sitting at the computer, worked great with win x64, i turned it off and then i went on a vacation for 2 weeks.
Later when i come home i wanted to use the computer but when i put on the power (power off during vacation) and the cpu fan starts (it always do for some reason) and i press the power on/off button everything dies and i couldn't boot the computer at all anymore. i tried to reset cmos and change dimm slot for my 512 mb memory and it worked so far. now i can boot up, and shut it down when holding the power on/off for a couple of secs but my graphic card wont work. monitor keep says no signal even though i tested 2 different graphic cards and 2 different 512 mb memory compenents. anyone have any experience of this problem or similar problem i would be greatly appreciated if you replied in this thread.
Grettings Golgor

sorry SAB, i cant!
no monitor and btw i just rebuilded my computer with my older asus a7n8 card with all the same components (Not cpu as a7n8 is a socket A) and it works excellent. Either it is the cpu or the motherboard's fault and i guess the cpu cant make the monitor go black?
perhaps something wrong with the agp slot or something. ill try to return it, if i cant i dont know what i'll do...
thx for reply anyway

Similar Messages

Monitoring airport Signal

I am using airport client monitor, my transmit rate is 54-Mbps, my signal strength is -60Db and the noise level is -95Db in this conditions my network works fine and I am near my airport express BS. If the strength signal drops to -80Db, I start having problems the transmit rate starts oscillating, going up and down(20 to 25-Mbps), and may stabilize at a lower transmit rate or after a while go back to 54-Mbps in this situation I am at six meters from the base station with a brick wall in between. Looking at the airport client monitor graphic there is a distance between the Noise and Strength curves about 10 to 12 Db.
Why I am having problems if I am only 6 meters from the AEBS? There is a graphic with a relation of distance from the AEBS and signal strength?
what is the relation of transmit speed, signal strength and Noise?
thank's
Luigi

I tried changing channels from automatic to 1, 2, 10 - all three of them showed the drop down to 0 every 25 seconds. That is not normal right? I got a slightly better signal at channel 2 but not by much. I also changed from b and g to g only. And increased the multicast to 5.5 and enabled Interference Robustness. And I got iStumbler and learned that my neighbor's open network is using channel 6. There is another closed network using channel 11. I currently have it set at chanel 2. What should I expect the numbers to be and is the transmission rate supposed to be a straight line up at the top and not dip down to zero on a regular basis? Also, I have an Airport Express running version 6.1. When I open Airport Admin Utility it asks me if I want to upload firmware 6.2 but I said cancel based on the posts I've seen in the discussions. Also, I have cox cable high speed internet and the tech guy that just came out told me that my BestData modem is notorious for dropping out and that I should buy a Motorolla 5120 modem. I just got one but haven't tried it yet to see if it made a difference. Before I did I wanted to learn how to monitor the signal so that I could see very specifically if it was improved or not. Also, after getting iStumbler I walked around the house checking the signal and right near the airport express I get a 60 and in the next room a 44 and then other parts of the house around 30 to 20 to 7 depending on where I go. Noise says 0. What should I try next? Also, just got a new phone 5.8 ghz instead of the old 2.4 and tried using the phone and it doesn't seem to have an effect one way or the other.
Also, are their any good sources for reading up on using the Airport admin and monitoring tools?
-charlene

My iPhone 4 with iOS 6 is making me start to hate Apple. Any App and at any time I open and I can not view it or move for more than 2 minutes, they close themselves. During connections, it also gives this problem and the signal disappears after a few seco

My iPhone 4 with iOS 6 is making me start to hate Apple. Any App and at any time I open and I can not view it or move for more than 2 minutes, they close themselves. During connections, it also gives this problem and the signal disappears after a few seconds back but often the person on the other end has hung up ... I can not stand it anymore, someone suggests something?
Besides these problems, there is the battery, which was bad got worse, she is not lasting more than 10 hours, even without using the phone.
Sometimes it even seems that the problem was solved, but my joy did not last long after I celebrate all the problems return, is incredible ...
thanks.
Sorry my bad Inglês.

Try a reset hold home/sleep buttons until Apple logo appears
If that does not improve try a restore
http://support.apple.com/kb/HT4137
For your information
We are NOT Apple here we are all users helping other users
so emotion is ignored

How to see a stream of a signal in the Data View while monitoring a signal.

Hi!
I'm migrating from an older data acquisition software for SignalExpress. With the DAQ old had a way to monitor the signal so that the software screen I saw on the timeline and as I increased or diminished the scale of the X axis (time), I saw more or less signal transitions in screen, respectively. For example, if the time scale (x axis) was set to 5 seconds and the signal that I was monitoring commute every 1 second, I would see on the screen of the software 5 sequential pulses.
I am not able to configure my data acquisition that way. What I have noticed is that the scale of the X axis is limited to the value of the "Samples to read." With that, I see the sign on the software screen is instantaneous and not a sequence of pulses.
I intend to monitor the signals are random signals originating from idependentes and switching relays.
In summary, I believe that the solution to what I want to do is increase the scale of the axis X. How to do this?
I use SignalExpress 2011, USB-6363 DAQ step and Digital Line Input.
Thank you.

OKors,
First, sorry for the delay in responding to you. And second, thanks for your reply.
I will try your suggestion: continuously scrolling "strip chart".
To try to clarify, what I want is to merge than I can with Digital Graph - signs lined up vertically with the display type Chart, where it can act on the parameters of History Lengh, as you suggested, to achieve "curb" the transition graph .
If using the first solution, Digital Graph, the screen transitions are very fast. On the other hand, if using the graph chart type for digital signals, they overlaps, since all have the same value - 0 or 1.
The idea is that these two characteristics in a single graph (Data View). I believe something to be simple, but I'm having trouble mounting this setting.
That's it. Any news ... I'll post here.

Wierd problem with web start in windows 7

I have a wierd problem with my web start app in windows 7, it just hang it self. it work fine in windows XP and Vista.
The wierd thing is that i can open the app but when i press on a specific button that will make a jlabel present a .png image everthing crash. why do i get this problem now? when i start the app, i load some pic i jlabels and that seems to work fine, but when i do it under the exection it seems to crash, why?
Should i do something different to make the app work in windows 7?
I hope someone can help me out!!

You should:
a) open the console (java control panel, advanced options) and see the stackTrace (if any). If it's not there check for swallowing.
b) post a code snippet, to at least show how and where you retrieve the png. Possibly a SSCCE.
c) check if this happens also running as a standalone app (may be more Swing-related than JWS-related).
Bye.

Oracle Report Server wierd problem

Hi All,
I am facing very wierd problem with oracle report server.
I am using Oracle Report Server 10g R1. The problem I am facing is as under:
There is custom parameter form where user enters report filter criteria and press a button to create the report.
The problem is that report is giving output some times and sometimes it gives no output at all. Both the times, the parameters passed by user are same. The report executions are done for both runs one after other. We have tried to look in report server trace file but could not find anything. When report server fails to give any data in the report, at the same time, we have tried to execute the report query on SQL prompt and it did return data.
Can any one give any hint where the problem could be ?
Thanks,
Ramchandra Jetwani

Hi,
When i used to get only one page the options like facing, continuous facing are disabled. And displays only single page.
These options are enabled only when there are multiple pages in pdf.
One more thing i found that it happens when I first view the report as pdf it displays
all the pages, then i change the display format to csv and again when i change
the format to pdf the problem starts.
And when I will restart the report server service, it works fine again until i wont view it in CSV format.
Message was edited by:
Yogesh

Wierd Problem

Hey guys, I wonder if you can help me..
Im having a wierd problem with my wifi/safari - i connect to my wireless network, youtube videos work fine, and google searches also work fine. The problem is, other then searches on google, no other websites load up. So for example if I were to search for "Ipod Touch" in google it would give me the list of all the sites, as you would expect google to do, but when it comes to me loading one of the pages it just wont load... Itunes is also not working..Its driving me mad....
I dont think its a problem with my router as my laptop, my wii, and my psp all work...
Any suggestions as to what to do?

What error(s) are the users receiving on the affected vlan? Are they using XP with the local firewall?

Updating a databse using jsp. Wierd problem

Can anyone help me with this wierd problem.
I update a databse using:
stmt.executeUpdate("UPDATE status_table SET " + updateString + " WHERE login = '" + userLogin + "'");
The updateString is:
otrans_comments = 'Please submit certified true photocopies of your individual marksheets for each semester/year of bachelor's work as issed by Thapar Institute'
as collected by a HTML form.
Observe that there is an apostrophie in bachelor's and this would cause pblms. I do not want to restrict users from stopping the use of apostrophie and neither can I remove apostrophie using other Java.String methods.
Is there any other way?

And by the way if this helps. I make my updateString like this:
comma="";
updateString="";
for (Enumeration en=request.getParameterNames();
en.hasMoreElements();) {
String name = (String)en.nextElement();
String value = request.getParameter(name);
// added to replace ' with `
if(name.endsWith("_comments")){
String newValue=value.replace('\'','`');
value=newValue;
updateString += comma + name + " = \'" + value + "\'";
comma = ", ";

SNMP traps to monitor the signal strength on wireless AP

What snmp notification type should I enable on wireless AP to monitor the signal strength of the connected devices to the AP. What is the associated MIB for this SNMP trap.

Hi karthikeya,
Here is the link which gives us the info regarding the available MIB for the respective Model..
http://tools.cisco.com/ITDIT/MIBS/MainServlet?ReleaseSel=3469&PlatformSel=9&fsSel=1292
Please select the Device part number and then chose the MIB that you require.
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

A wierd problem while encoding URLs

Hi all,
I'm facing a wierd problem with the java.net.URLEncoder class. The encode function in this class is used for encoding URL based on standards like "UTF-8" etc..
I need to encode the URLs, because i have to send this information in a XML to another server.. Here's what the URLEncoder is doing if i give it the URL
http://mydomain.com:80/myServlet?_fileName=filename.mp3&_useStreaming=true
its encoding this as
http%3A%2F%2Fmydomain.com%3A80%2FmyServlet%3F_fileName%3Dfilename.mp3%26_useStreaming%3Dtrue
but, all I wanted is to encode only '&' character ( as XML misinterprets this character with schemes ).
So, my question is .. is there any way that i can selectively encode the characters in the URL?
Any help wud be appriciated in this regard. :-)

I accept what you are saying.. URLEncoder encodes any string that's passed to it..
I infact have two different problems in hand.. The reason i mentioned only one above is because the solution to the first problem cud as well solve the second.. Anyway, here's the second problem ...
I'm recieving an XML from a server, where i get the URL info and i have to download the CONTENT from that URL.. Sample xml is given below
<Music>
<Singer>Tata Young</Singer>
<contentURL>http://myMusic.com/sexy naughty.mp3</contentURL>
</Music>
if you see the URL in the xml, that infact contains spaces in it.. I have my logic which checks if the given URL is a absolute URL or relative URL
if( relative URL)
I append "http://domain name:" stuff to make it absolute
else
i connect to the URL directly to get the Content
I'm using
URI i = new URI(str);
i.isAbsolute() method to determine whether its a absolute URL or not..
but this method doesn't seem to work for URLs that have spaces in them.. So, i encoded the URL and tried passing it to the method.. but it still doesn't work..
I probed into URI class itself and found out to my amazement that URI class assumes that URL contains only alpha numeric characters and few special characters like '+' , '/' , ':' etc..
Since the encoded URL has '%' character in it.. its not able to say that its a absolute URL.. Tht's the reason I asked for selective encoding.. ( say, which encodes only [space] character)..

This is a wierd problem!

Hey guys!
*Please just read this first!*
THE INFORMATION BELOW HAS BEEN DOUBLE-CHECKED SO PLEASE BE RELEVANT WITH YOUR EXPERT SOLUTIONS!*
Me and my cousin both have the CURVE 8520. We both have the same OS (5.0.0.1067 platform 5.2.0.96)
We are both on the same GSM provider (warid pakistan). Our provider supports cell tower triangulation.
Here's the interesting part:
He is able to check-in on facebook but i can't! (I can assure you he has the curve 8520 and NOT the 8530)
(I know the curve 8520 does NOT have gps)
We're both using the latest facebook app (3.1.0.17)
(please refrain from telling me that he has the curve 8530 because:
1. our provider is gsm and i believe the 8530 is cdma
2. I have checked and checked again.
Any sloutions to this wierd problem will be greatly appreciated!
THANKS!

Hi abubakar91,
Welcome to the BB Community...
Thats kinda weird...anyways, try reinstalling the FB...might this will solve the issue...
Are u able to access other services which needs BIS service...???if not, then check with ur service provider...
with regards
simply abhik...
Please click "Accept as Solution" if your issue has been solved and to give thanks/appreciation, click thumbs up...
For BB OS update: http://us.blackberry.com/software/smartphones/update.html
BB Simulators: http://us.blackberry.com/sites/developers/resources/simulators.html

Wierd problem in iTunes Match with iPhone 5

iPhone 5 with iOS6. I have a wierd problem. I have iTunes Match turned on. All of my songs show up when I tap Songs. All of my playlists appear when I tap on Playlists. Great. BUT, when I tap on Artists (my preferred view) it says No Music. What the heck?!? Works fine (great even) on my iPad.

I'm having the same problem. I can access my itunes match on iphone 5 via wifi, but when I'm using 3G/4G/LTE in get a error message stating my membership has expired. This only happens on the iphone 5. It didnt happen on my 4S and nor does it happen with my "New" ipad Verizon. I'm not getting kind of help via itunes express, which *****. I'm starting to realize the iphone 5 is a piece of junk.
screenshoot:
https://www.icloud.com/photostream/#A15oqs3qG2p5MK

My Mac pro tower has an "ATI Radion hd 2600 XT" video card, and it stopped getting signal to my tv, are there common problems known? How can I troubleshoot this problem when the signal isn't reaching the screen?

My Mac pro tower has an "ATI Radion hd 2600 XT" video card, and it stopped getting signal to my tv, are there common problems known? How can I troubleshoot this problem when the signal isn't reaching the screen?

http://discussions.info.apple.com/thread.jspa?messageID=12248238&#12248238
http://discussions.apple.com/thread.jspa?threadID=2649035&tstart=0

Probleme monitor l1906

probleme monitor l1906 blinking and not connect vga. what solution
http://www.youtube.com/watch?v=tUb-5ASy8ls

Hello softrif,
I have watched your video depicting what your monitor is doing and the issue appears to be a physical issue and I think it would be best if you contacted HP technical support for repair options.
US support link to contact options for HP products purchased in the US.
Outside of US support link to contact options for HP products purchased outside the US.
I would like to thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Zen stone , Wierd Problems. !!!!

Hey ,
I have a Zen stone , i was happy with its performance. but now its got some wierd problems which make it completely useless.
Its not getting charged. When i plug in it to a PC , it gets detected & i can do all the transfering.
But when connect it to a charger, it automatically starts playback ..!!!
After disconnecting the charger if i try to switch it ON, it won't power up.
What could be the possible problem?
If the problem is with battery, Is there any option to change it's
Regards,
Jerin George.

Did you charge your player before you used it's Even if you charged it when you first got it, 30 days would probably be enough time for the battery to discharge quite a bit...

Wierd problem, monitor no signal.

Similar Messages

Maybe you are looking for