WiFi device not found.

After I upgrade my IPhone 4s to ios8.1,  the wifi can't be opened.
And I search 'wifi' in log found something below:
Nov  2 16:44:57 iPhone SpringBoard[43] <Error>: WiFi: "no-sdio-devices" property not found.
Nov  2 16:44:57 iPhone SpringBoard[43] <Warning>: ERROR: WiFi device not found.
Nov  2 16:44:57 iPhone SpringBoard[43] <Warning>: WiFi picker plugin initialized, logging enabled 0

I had the same issue.  Went to Genius bar and they wanted to charge me £170 to replace the phone.  They wouldn't admit it is a common issue - even though this has clearly happened to huge numbers of people after updating to IOS8.  Apple must have know this would happen and clearly see it as a route to more profit when everybody has to upgrade their phone.
I'm disgusted by Apple.  This is not how you treat customers who buy your ridiculously expensive products!

Similar Messages

  • Trying to transfer a video clip from iPhone to iPad using transfer app it says device not found, I have used this before wifi is fine and both  devices are connected ?

    Trying to transfer a video clip from iPhone to iPad using transfer app it says device not found, I have used this before wifi is fine and both  devices are connected ?

    That does not involve iPhoto for the Mac in any way - try the iPad forum
    I will request your post be moved
    LN

  • HP 3050A : Device Not Found on Network

    Hi,
    Laptop Model: MacBook Air
    Operation System: OSx Lion 10.7.3
    Printer Model: HP 3050A
    Router Model: Linksys WAG160N
    WiFi Security Protocol: WPA
    TCP/IP IPv4 Protocol: DHCP
    Firewall Software: None
    I have manage to connect the printer to my WiFi network as the blue indicator is ON and got an IP 192.168.1.104 with Excellent signal strength on the printer. But when follow the HP Setup Assistant I unpluged the USB then I got stuck with the following error message:
    Device Not Found on Network
    The wireless network settings were successfully downloaded to your device. However, your Mac was unable to locate the device on the network.
    Please make sure that:
    • Your Mac is connected to a wired or wireless network that has access to your device.
    • Your device is connected to the wireless network "speedy".
    Click "Retry" to attempt to connect again using the current settings. Click "Go Back" to enter different settings.
    I also tried to ping the printer IP but no success
    Aliss-MacBook-Air:~ ali$ ping 192.168.1.104
    PING 192.168.1.104 (192.168.1.104): 56 data bytes
    Request timeout for icmp_seq 0
    Request timeout for icmp_seq 1
    Request timeout for icmp_seq 2
    Request timeout for icmp_seq 3
    ping: sendto: No route to host
    I am able to print using USB without any problem, but the WiFi never success! Please help!
    Regards

    Hello,
    Thanks for the post.  With this one, we may a couple of issues.  I've included a link below with some excellent information regarding network connectivity.  I might suggest that we start there and try to determine if it's the printer, the MAC or the network.  Good Luck!
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02731071&tmp_task=solveCategory&cc=us&dlc=en&la...
    I worked for HP but my posts and replies are my own....Thank you!
    *Say thanks by clicking the *Kudos!* which is on the left*
    *Make it easier for other people to find solutions, by marking my answer with (Accept as Solution) if it solves your issue.*

  • Time capsule device not found

    I have a recurring problem backup failed and device not found.
    I have been on to apple told pull the plug on time capsule every time.
    now i am told to go into network and take it of automatic and set it to 2.4 to channel 11 and the 5 to channel 44.
    is this now limiting the time capsule to the 2 channels.
    is this the best result for the time capsule or would i be better getting a non apple product.

    the phone has been switched of and unplugged
    just checked my Time Machine and its missed backups again.
    I go into airport utility yet again its missing the time capsule.
    I am sorry, but Yosemite is doing its thing.
    So much for Apple blaming my cordless phone.
    Apple has to find something to blame, since they will never blame themselves.
    have a program from the app store wifi checker.
    running it looking at the wifi signal in my area I have 2 main accounts with 2 different BSSID the last letter different on each.
    I also had for a bit 3 guest accounts 2 with the same BSSID and 1 different BSSID there is another wifi account not mine with the same BSSID as this 1.
    This all sounds normal.
    I am afraid that all you can do is wait for the next Yosemite update to see if it will fix some of these issues.

  • Start-up problem with hp pavilion dv6t-7000‏: "Boot Device Not Found. Hard Disk (3F0)" error

    I started getting start-up problems with my hp pavilion dv6t-7000‏.  It happens intermittently. 
    The boot error is:
       Boot Device Not Found
       Please install an operating system on your hard disk.
       Hard Disk (3F0)
       F2 System Diagnostics
       For more information, please visit: www.hp.com/go/techcenter/startup
    Could a faulty BIOS update cause this problem?
    Anyone else who may have experienced a similar problem?
    I'd appreciate any help about this problem.  Thanks.

    Hi
    Please find the link given below might help you to fix your issue.
    Resolve Boot Device not Found Error Message
    Let us know how it goes!
    "I work for HP."
    ****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    Regards
    Manjunath

  • T410 bluetooth device NOT FOUND

    Hello Everyone,
    I have a t410, product id is 2539AJ6 (bluetooth included), running Windows 8.
    however i can't get bluetooth to work, in addition it seems like there is no trace for a bluetooth device on this computer:
    - Can't install driver ("Device not found").
    - Not Recognized by Windows 8.
    - on BIOS, Security -> I/O Port blah blah -> no mention of bluetooth settings there.
    where do i go from here? anybody ever encountered such an issue with bluetooth?
    btw, im pretty sure there is a bluetooth device on this laptop. 
    appreciate any help

    Here's the Link for the 2539-AJ6, it does indicate that you have Bluetooth.  Dowload and install the latest drivers.
    http://support.lenovo.com/en_US/downloads/default.page?

  • HP Device Not Found Error when trying to print or scan wireless- HP Officejet Pro L7590

    Have had HP Officejet Pro L7590 All-In-One Printer for years.  Always worked fine and I had no issues printing via wireless connection.  Several months ago..  Possibly after a Windows 8 update.  From Windows 8 to Windows 8.1 I have not been able to use the printers wireless feature.  When I try to print or scan it shows the printer as offline.  Also get an error message that tells me "HP Imaging device is not found".  I can still print when connected to USB.  Cannot scan or use features of the HP software suite.  I have tried several times to correct.  Reloading the software and drivers several times, but no success.  I just tried again and was able to print the test page wireless, so got all excited and thought I fixed it.  Then tried to print something and got the same error message I have seen in the past.  I have talked to certain supports saying that it may be a firewall setting within Windows.  Any other suggestions?  Thanks

    Hi @rfjones002,
    Welcome to the HP Support Forums! I see you are not able to print or scan wirelessly to your HP Officejet L7590 and your computer running the Windows 8.1 Operating system. You get a 'Printer offline' or 'HP Imaging device not found' errors.
    I would like you to start with the steps listed below:
    Hold down the Windows Logo key () on the keyboard and the 'R' to open the run box, type %temp%
    Delete all files and folders from the temp folder. Choose skip if any pop ups appear saying any of the files could not be deleted
    Uninstall the software again - Uninstall the Printer Software Instructions
    When the uninstall has completed restart the computer
    Follow these steps to reset the registry settings and options for Windows Installer.
    Hold down the Windows Logo key on the keyboard and the 'R' to open the run box
    In the Open box, type
    msiexec /unregister
    and then click OK.
    Hold down the Windows Logo key on the keyboard and the 'R' to open the run box
    In the Open box, type
    msiexec /regserver
    and then click OK
    *Note: there is a space between the c and the /
    If you have any difficulty with this step, please use this link to perform it another way. Restarting Windows Installer
    Run Disk cleanup from Accessories\ System Tool < How to Delete files using Disk Cleanup
    Download and install the latest version of Adobe flash player http://www.adobe.com/support/flashplayerflashplaye​r/downloads.html
    Perform a clean boot > How to perform a clean boot in Windows
    Download the following SP40669 File Download - if this does not download and or install please proceed to the next step.
    Turn off the Real-Time Scanning and Firewalls; The image below is a McAfee example, if you have a different antivirus program and need help disabling Real-Time Scanning and Firewalls let me know.
    - Image source
    Now you can go ahead and download and install the software here >
    HP Officejet Pro Full Feature Software and Driver
    If you are unable to print a test page, please run the HP Print and Scan Doctor- It was designed by HP to provide users with the troubleshooting and problem solving features needed to resolve many common problems experienced with HP print and scan products connected to Windows-based computers.
    Please let me know if this was successful! I will watch for your reply.
    Thank you,
    HevnLgh
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • Photosmart 7515 connect via USB but not wireless, Device not found on Network

    Purchased a 7515 all-in-one, was able to setup wirelessly to MacPro but has lost ability to connect wirelessly.  This happened with OS X Lion and nor MountainLion.  Have a TimeMachine Airport.  Printer connects to network but during setup from MacPro, repeatedly get "Device Not Found on Network" after stepping through wireless installation setup screens.  I have reset router, printer, firmware updates, software updates.... at wits end.  I have followed the instructions on the below resource page link with no luck.  Use WPA-PSK encryption (Automatic AES or TKIP) on network and diagnostics on printer pass.
    Please help anyone!
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02946597&tmp_task=solveCategory&cc=us&dlc=en&la... 

    It sounds like the Macs and the printer just aren't communicating.
    If you press the network icon on the printer, does it indicate it is connected to the network?
    I recommend two additional steps that are not listed in the linked document.  The printing system of the Mac may need to be reset as it will clear any software that could be interfering (such as corrupted installations).
    Follow the steps as outlined for 10.7 or 10.8 in this document from HP.
    The next step is to install the driver package from Apple.  This can be found here.
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • I'm receiving error Boot Device Not Found and Hard disk not exist when I boot up my laptop

    I'm receicing the error Boot Device Not Found when i power on my HP G60-235DX laptop.  After following HP's recommended troubleshooting steps, I receive error Hard disk not exist.  Hmmmm....that's a little concerning.  My guess is I need a new hard drive?    I have the 17 recovery disks I made when I setup this laptop, however I'm not sure if they will resolve this issue.  Any suggestions?

    One of 3 things has happened, listed from most likely to least likely
    1. Hard drive has died, replace it with one of the same size or larger, then use the HP recovery discs to re-install windows.
    2, The motherboard has serious problems. (Replace the notebook)
    3. The hard drive cable that connects it to the motherboard has somehow failed, not very likely. (replace the cable)
    Replace the hard drive with a new one and use your recovery discs to get Windows back on it.
    Here is your service manual, will show you how to replace the hard drive
    http://h10032.www1.hp.com/ctg/Manual/c02985882.pdf
    Recovery Instructions for Vista
    Recovery Instructions for Windows 7

  • Presario CQ61 - Boot Device not found, Hard dis not exist

    Hi i bought my presario CQ61-405AX 2nd hand roughly a year ago and it was almost new, my laptop was running fine, and then it froze, and so i had to turn it off, after i waited 30min for it to unfreeze, it now, when i boot it up, appears with a black screen, with the error
    "Boot Device Not Found
    Pleae install a operating system on your hard disk
    F2 system diagnostiscs" 
    I went onto hp support and followed the prompts until it did a hard disk test and the error, "Hard Disk Not Exist" appeared
    I have no idea how to fix it, i am running Windows 7 home premium, and i fear i may have to buy another hard drive
    Thank's in advance
    This question was solved.
    View Solution.

    Hi,
    The most likely explanation is that your Hard Drive has failed and will need to be replaced, however as a further test, try the following.
    1.  Create a bootable Ubuntu CD - a guide on creating an Ubuntu CD and the download can be found Here.
    2.  When created, follow the guide on the link below to Try Ubuntu.
    http://www.ubuntu.com/download/help/try-ubuntu-before-you-install
    The 'Try Ubuntu' option runs the OS from the CD without the need to install on your HDD.  If this runs Ok ( it will be slow running from a CD ), this would tend to confirm that the problem is with the HDD.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Boot device not found. "Hard disk not exist". windows not booting

    Product: HP G72-110SA
    OS: Win7
    two days ago, I was installing updates on my computer and when it was about to restart, it froze. After waiting for 10 minutes, I had to turn it off by pressing the off button. From then on, the computer turns on but shows a message "Boot device not found".
    I have tried all the BIOS tests that I could find on the net for the hard disk, eg: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01443465&tmp_task=solveCategory&cc=uk&dlc=en&la...
    This gives me a "Hard disk not exist" error. I tried resetting the BIOS, that didn't work. I tried taking out and putting back in the battery, the memory and the hard disk. Still no luck.
    I then booted ubuntu from cd on the computer. It works just fine, including the internet etc EXCEPT the HDD is still not detected.
    I had some pretty important stuff and no back up, so would appreciate if someone can help me get back the data. If not, even if I know its just a HDD failure and not a motherboard/BIOS problem, it will be a relief as its probably fixable.
    Thanks

    Hi there ,
    Thank you for visiting the HP Support Forums and Welcome! This is a great site to get answers and ask questions. I would be happy to assist you. As there are many models of HP Notebooks, I would need the model number. (How Do I Find My Model Number or Product Number?) When I went to www.hp.com/go/techcenter/startup, it gave me documentation and troubleshooting steps to follow. One of the documents it provided is called Hard Disk Error Displays before the Computer Starts. NOTE: I recommend at this point you make an immediate backup of all important data and files. Here are instructions on how to Backing Up Your Files (Windows 8). Please follow the troubleshooting steps provided, re-post with the results of the troubleshooting in detail. Thank you.

  • Boot device not found, hard disk not exist.... does that mean my computer is dead?

    Suspecting that Im in a world of hurt here. I tried turning on my computer and it says "boot device not found" - run in test failed... when I hit F4 and run a hard disk test it says "hard disk not exist". The memory test passes, but under the boot device not found it says in blue "please install an operating system on your hard disk"... and to make matters worse it's making some funny noises when it tries to boot.
    Is there any hope at all that this computer will work again? Is there any chance that any of the things I had on my hard disk can be recovered?
    This question was solved.
    View Solution.

    You're very welcome, Jonathan.
    dv5 still isn't enough info for me to provide the service manual (in case there are differerent ones for the different dv5 models).
    However here is the link to the service manual I randomly pulled.
    http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c01550108/c01550108.pdf
    Assume it is safe to say all dv5 models come with SATA notebook drives.
    So, if you want to spring for $15, you can get this enclosure which apparently has very good reviews.
    http://www.newegg.com/Product/Product.aspx?Item=N82E16817182138
    From what you are describing (noise and stuff), I would say you don't have much of a chance to recover data but that is up to you if you want to try the enclosure or not.
    Here is what I recommend:
    Yank the hard drive, and power on the notebook.
    If the odd noise you heard is gone, then you can pretty much safely assume the drive was the cause, and that replacing the drive, and reinstalling the operating system will solve the issue.
    If the noise is still there, then there could be another issue, and it might be risky throwing good money after bad.
    Paul

  • Re: Satellite L50-B05D can't load Win 8.1 - bootable device not found

    Hi
    I have a Satellite L50-B05D and I recently downloaded the bios update and I applied it to my system. When I did it said that it contained the update already. After being on the laptop for a while, I closed the lid and it turnt off. When I turnt it back on Windows wouldn't load up and a message of bootable device not found occured.
    Any help is appreciated
    Thanks

    Did you check the HDD status on the first BIOS page?
    If HDD is OK, the first BIOS page should provide the info about the connected HDD (HDD name)
    At the other hand the HDD might be faulty if its not listed on the first BIOS page.

  • Device Not Found

    I have been using a Time Capsule with with Mac Air 13 inch for the last 1.5 years. the Time casule is the main wi-fi router in my network. off late i have started getting a message Device not found, where as the internet is connected. due to this error no data (time machine) back up is available. also this issue leads to internet disconnection on my Mac (where are other devices lice PC's and iphones are connected to the same network without any problem).
    Please help me if anyone has a solution.

    You hidden the most important thing.. the name of the TC. I don't know why as we can certainly not connect to it remotely.
    The name looks wrong though if I am seeing it right.. in terms of being too long and having spaces.. and possibly many of them.
    There is a bug.. if you reboot the TC this issue will go away for a few hours.. or days..
    Have you rebooted btw??
    Do a factory reset of the TC.
    Change all names to SMB standard.. that means universal not Apple only.
    SMB names that work..
    Short.. 2-20 characters
    No Space..
    Pure alphanumeric.
    You need that for TC name.. wireless name/s and hard disk share name.
    Please see C9 for a more apple explanation of what long names do.
    http://pondini.org/TM/Troubleshooting.html
    I would also go back to 7.6.1 firmware.. if not earlier.. 7.5.2 is very stable.. but later Gen4 can only go back to 7.6.x

  • Boot device not found - Please install an operating system on your hard disk

    Trying to boot up this morning gave this error message:
    "Boot device not found
    Please install an operating system on your hard disk
    Hard Disk <3F0>
    F2  System Diagnostics"
    Pressing F2 brings up to  the "HP PC Hardware Diagnostics UEFI" page, where its shown:
    "Version 1.6.0.0 - BIOS
    Fore more info please visit www. ... ...
    Memory Test
    Hard Drive Check
    Language
    Exit"
    Tryied the HD check but it says:
    "SMART Check : Not installed
    Short DST : Not installed
    More details:
    No bios upgrade was made, never, only a big updating of Windows yesterday.
    Could someone kindely help me out please?
    Thanks, Perry G.

    Hi,
              The above error message shows that the Hard disk drive is failed on your unit. You have to replace the Hard disk drive and reinstall the OS.
    To order parts click the below link
    https://h20141.www2.hp.com/Hpparts/Default.aspx?mscssid=FA59F7C7DCAC4237B498C91D0507A761
    To order Recovery disk click below link
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=bph07143&cc=us&dlc=en&lc=en
    "I work for HP."
    Please click the "White Kudos" star to say thanks for helping.
    Please mark "Accept As Solution" if my help has solved your problem.

Maybe you are looking for