Wifi disconnect wen The display turns off

Hi,
i have
asus t100
There is a problem Power settings sleep and display off, is not separated as a laptop or PC.
Should be three plan settings (as pictured).
I have only one option,
sleep.
*exmp
after changing the advanced power settings
That the display will turn off after 2 minutes
Sleep mode is also changed to 2 min!!
I tried resetting, does not help.
And brightness rises after
resuming from sleep.

Hi,
It seems that there are several similar issues happened on ASUS computer.
Please check the solution in following links:
http://superuser.com/questions/545057/why-does-this-monitor-go-to-sleep-but-wont-wake-up-event-though-all-related-po
http://superuser.com/questions/516188/how-to-turn-off-the-display-in-windows-8-without-locking-or-making-computer-go-t
http://social.technet.microsoft.com/Forums/windows/en-US/7e08ba03-4ac3-4af7-8bba-6cbff5ff864e/turnoff-the-display-without-letting-the-device-to-go-into-sleep-in-windows-8?forum=w8itprogeneral
Hope these could be helpful.
Kate Li
TechNet Community Support
It also does not help

Similar Messages

TS3700 My ipod stills pauses when the display turns off, even though, my headphones are correctly attached (or flushed)

My ipod stills pauses when the display turns off, even though, my headphones are correctly attached (or flushed)

Does this happen still when you use another set of headphones? Have you check to make sure the headphone jack is clean and clear of debris? If so, the jack may be faulty or damaged meaning you'll need to take or send your iPod in for service/repair.
B-rock

How do I restore a MBA with a broken screen if the display turns off during the restart?

I have a MBA running OSx 10.7.5. The monitor is broken; can't see anything. I'm attempting to restore it completely, but every time I go to restart it, the VGA connected secondary display goes black. Any ideas? Do I need to buy another cable or is there another way?

You can go to Settings>General>Auto-Lock and switch it to "Never"
Of course this will keep your screen active and never lock your phone, but it will be using battery more.
You can still lock the phone yourself in the normal way (Hold the Sleep button)

W520 - now changes to "projector only" whenever display turns off in power save mode

I have my W520 in a dock with an external monitor. The display is configured to Extend - the external monitor is primary, and the desktop extends onto the W520 screen. I don't have a screen saver. I turn off the display after 30 minutes of inactivity. Until recently both the laptop and monitor screens would turn off after 30 minutes, and then both resume when I moved the mouse or pressed a key.
Recently, the system has started changing to "Projector Only" when the display turns off. After resuming from power save mode, only the external monitor activates, and the W520 screen is disabled. I have to use Fn-F6 to switch back to "Extend" to re-activate the laptop screen.
I have rebooted and re-saved the power plan.
Why has this happened, and how do I fix it?

Hi, timg11
I have a few questions so that I may gain a better grasp of this issue:
1) What is your machine type and model? You can find this information on the bottom of your machine. It should be in format XXXX-XXX.
2) What is your operating system?
3) Does this issue occur is the computer is not in the docking station? (Please try if you haven't already).
Thanks in advance,
Adam
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it.

L305D-S5935 Unresponsive After Display Turns Off

I have a L305D-S5935 running Windows Vista and it becomes unresponsive after the display turns off as set to do so in the power settings. I cannot push any key or button or move around on the mouse pad to get it to turn back on. This is very frustrating and the only way to get it to come back on is to to a hard restart.

Turn off your laptop, unplug all wires, remove the battery, and hold the power button for thirty seconds. Afterwards, reattach the battery and connections.
Then reinstall TVAP.
Toshiba Value Added Package for Windows Vista/7 (32)(v1.2.33; 11-09-2009; 43.67M)
- Peter

Windows 8.1 Screen Locking at Display Turn Off (instead of only at Sleep)

Hi All,
I am having this issue with clients running Windows 8.1 Enterprise, which we are planning to deploy later on this summer.
We currently have a GPO setup for managing the power settings on our staff computers:
This GPO sets computers to sleep after 1 hour, but turn off the monitor after 5 minutes of inactivity
On our Windows 7 systems, the policy applies correctly and if our staff uses their computer before 60 minutes of inactvity (before they go to sleep),
the screens will just turn back on without prompting for login.
I have noticed however on our Windows 8.1 test computers, in the same OU, which receive this policy, that after 5 minutes when the screen goes off, if a staff member attempts to use their computer they will be prompted for a password even though the
unit was not in sleep mode.
Further more, I've noticed that on the Windows 8.1 Systems, I am able to override the "Require a Password on Wakeup" setting using the metro interface, as pictured below (the setting does change in power options as seen below), and does stay in
the No setting even if I run gupdate and reboot.
Any idea how to keep the Require Password for waking up, but not just for computer with the screen powered down?
(I should also not screen savers are not being used)

Hi,
You can tried also set the item Sleep: After 60 min to see what's going on.
On my laptop, once I configure this, the display turns off without lock the computer.
Kate Li
TechNet Community Support

Macbook pro 15" and 17" display turns off whilst working then.......

I have 2 macbook pros. One 17" and the other 15" both are the non unibody ones. The 15" had this problem a while ago but my 17" never did it until today and then it did about 5 mins ago.
Whilst I am working (never seems to happen when I am not using it) the display turns off whilst working. The power light remains constant (ie:- not fading in and out when asleep). But here is the strangest thing. The mac repetitively makes the same noise as if it was ejecting a disk. Has anybody else had this? Know a cure? I recently upgraded to snow leopard but don't think this is a software issue.

I got the same problem with mine, 15". I bought it refurbished from apple store. I had this problem when i bought it then nothing happened for 4 months. But now my MBP has started doing it again. And i don't think it's a software issue. My display switch on after few sec, or 1-2 mins it's depends, and it's pretty random. i'm a bit of worry

Mac display turns off?

Hello everyone,
I don't understand why my Mac display turns of automatically when another electronic device is brought near it. The system is still running but the display just goes black and Mac logs the user out. The other day I got off the phone while working and I put the phone on the left side of the Mac just above the speakers and display went black. I pressed the keys but in vain. I removed the phone and put it back in the dock. The display comes back to life with me logged out.
The happened many times after it and before the incident but the thing I observed it, the display turns off when an electronic device is brought near it. The weird thing, it turned off when I put the Mag Safe pin on the speaker noticing that the power is full. Is it due to some kind of interference of the Mag Safe's(other devices) magnetic field with Mac's power ciruits? I also noticed that this happens only when the device in context is on or plugged in. I just want to make sure that thats the reason or my Mac has some problem!!

You should call Apple service number they will surely help you. You should find it in your computer's documentation. Good luck!

Macbook display turns off when booting Snow Leopard DVD

I have mid-2009 Macbook Pro and I hate Mountain Lion. I want to do a clean install of Leopard using the DVD (grey) that came with my computer. I loaned it to a friend recently and he had no issues. But everytime i try to boot from the SL DVD (hold C at startup) it behaves normally, until about the time it would go into the DVD startup screen. At that point the display turns off (not the whole computer, just the display) as if it has gone to sleep. And I can't get it to turn on again. I've also tried booting and holding Option and choosing the DVD as the boot drive. No dice.
Awhile back I created a Lion install DVD. I can boot to it just fine. But i don't want Lion either. Any ideas why this is happening? Thanks!

Press control shift eject, then any key to toggle the display from sleep/wake.

T42 Display turns off after moving

Hello everybody!
I´ve got a problem with my Thinkpad T42 (2373fwg), XP prof. with the latest updates running. After installing the latest drivers for display (ati) and for "ThinkVantage Active Protection System " the display turns off immediately after moving the Thinkpad. I can turn the display on again only by reboot. The error appears even in a second after reboot, so it doesn´t concern to windows. The system doesn´t crash, it´s only the display. The problem might concern to the shock sensor, but I don´t know how to solve it.
Does anyone of you has an idea?
Thank you and kind regards
Bill
Message Edited by billyflinn on 01-26-2009 09:29 AM

I have a similar problem: T42 (2373-5wg) Screen blanks. At first screen blanking was rare and seemed to happen when moving the pc, but now the screen blanks within 1-3 minutes after turning on the laptop, even if the computer is left untouched after being turned on.
It is not OS related as the blanking appears even when in BIOS setup or booted on a liveOS CD.
I can't tell for sure if the system crashes or not as the display goes blank (doh!), however, I have seen no reports of registered crashes in the visible part of the boot process.
The screen blanking appears quicker (or even instantly) if the computer is warm (e.g. turned off just before being turned on).
Blanking appears simultaneously on the LCD and on any attached external monitor, so I believe this rules out a defective LCD, backlight or inverter board.
I'm thinking it's a failing graphics adapter or system board, or maybe a loose connection that causes a component to overheat and fail. But I don't know which or how to fix it.
It IS out of warranty, of course. Any ideas?
Thanks in advance,
Niels
EDIT: It seems this could be yet another case of badly soldered BGA chips that seems to be troubling the T4x series:
http://forum.thinkpads.com/viewtopic.php?f=2&t=33952&sid=99545e4d13d9a94ce7496a5022690ed8&start=30
http://www.technotaste.com/blog/thinkpad-t42-ati-radeon-9600-driver-and-the-blue-screen-of-death-bso...
Message Edited by NielsCN on 01-26-2009 12:11 PM
Message Edited by NielsCN on 01-26-2009 02:25 PM

IMac display turns off automatically.

Hi everyone!
I have a problem with my iMac. The display automatically turns off while using the computer and I can't continue using it without forcing it going to sleep. The display turns off when the screen brightness is NOT at maximum level. If I reduce the brightness, the screen turns off. If the display it's at the maximum level, no problem, works perfect. No matter if the computer is just turned on from a cold start or if it's running since hours with high temperatures. In System Preferences there's only one option selected in the Enegy Saver section (Allow power button to sleep the computer).
Any ideas? It's really annoying working with this problem (especially at night with the brightness at maximum).
Hope somebody can help me!
(Sorry for my english).

Hi everyone!
I have a problem with my iMac. The display automatically turns off while using the computer and I can't continue using it without forcing it going to sleep. The display turns off when the screen brightness is NOT at maximum level. If I reduce the brightness, the screen turns off. If the display it's at the maximum level, no problem, works perfect. No matter if the computer is just turned on from a cold start or if it's running since hours with high temperatures. In System Preferences there's only one option selected in the Enegy Saver section (Allow power button to sleep the computer).
Any ideas? It's really annoying working with this problem (especially at night with the brightness at maximum).
Hope somebody can help me!
(Sorry for my english).

I've lost my iphone with passcode lock and find my iphone lock on but the wifi n cellular data was turned off so no way i can trace it so the only question remains is will the person who finds it be able to unlock it and use it as his own ?

i've lost my iphone with passcode lock and find my iphone lock on but the wifi n cellular data was turned off so no way i can trace it so the only question remains is will the person who finds it be able to unlock it and use it as his own ?
is it possible to change imei number?
i've tried for so many times n still the phone is offline so i've set it to offline mode with my message but it never shows the last location why?

If the device is found, nobody can use it without knowing your Apple ID and password.
The phone will only show it's location if it is connected to cellular network or Wi-Fi. If those options are switched off, you can't locate the phone.
With iOS 7, Find My iPhone includes a new feature called Activation Lock, which is designed to prevent anyone else from using your iPhone, iPad, or iPod touch if you ever lose it. It starts working the moment you turn on Find My iPhone in iOS 7. With Activation Lock, your Apple ID and password will be required before anyone can:
Turn off Find My iPhone on your device
Erase your device
Reactivate and use your device
This can help you keep your device secure, even if it is in the wrong hands, and can improve your chances of recovering it. Even if you erase your device remotely, Activation Lock can continue to deter anyone from reactivating your device without your permission. All you need to do is keep Find My iPhone turned on, andremember your Apple ID and password.
What steps should I take if I misplace my device?
If you ever misplace your device—whether it’s just lost or you think it may have been stolen—you should put it into Lost Mode immediately using Find My iPhone.
Lost Mode locks your screen with a four-digit passcode and lets you display a custom message with your phone number to help you get it back. You can also remotely erase your device if needed, and your custom message will continue to display even after the device is erased.
While Activation Lock works in the background to make it more difficult for someone to use or sell your missing device, Lost Mode clearly indicates to anyone who finds your device that it still belongs to you and can’t be reactivated without your password.
To put a device into Lost Mode, sign in to icloud.com/find from a Mac or PC or use the Find My iPhone iOS app.
For more information, read what to do if your device is lost or stolen.
copied from iCloud: Find My iPhone Activation Lock in iOS 7

In my ipad mini sound is there but somehow display turned off....please help...how to turn on the display

In my ipad mini sound is there but somehow display turned off....please help...how to turn on the display

Frozen or unresponsive iPad
Resolve these most common issues:
    •    Display remains black or blank
    •    Touch screen not responding
    •    Application unexpectedly closes or freezes
http://www.apple.com/support/ipad/assistant/ipad/
iPad Frozen, not responding, how to fix
http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
Black or Blank Screen on iPad or iPhone
http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
Home button not working or unresponsive, fix
http://appletoolbox.com/2013/04/home-button-not-working-or-unresponsive-fix/
Fixing an iPad Home Button
http://tinyurl.com/om6rd6u
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
 Cheers, Tom

Did the most recent update and now my TB Display turns off randomly on both my air and mini. I running TB Firmware Version: 23.6

did the most recent update and now my TB Display turns off randomly on both my air and mini. I running TB Firmware Version:
23.6

When did you get this firmware version? My TBD is at 22.2 and the TBD bus is at 23.4. I thought I had the latest firmware.

Since upgrading my phone to 6.0.1, I'm using way too much data. I believe it's the podcast app that's not loading shows while I'm connected to wifi. I have the 3g turned off for podcasts??? also after a phone call or an alert it starts playing a podcast?

since upgrading my phone to 6.0.1, I'm using way too much data. I believe it's the podcast app that's not loading shows while I'm connected to wifi. I have the 3g turned off for podcasts??? also after a phone call or an alert it starts playing a podcast?

I've also had the same issues, after upgrading to IOS 6.0, the apps in my iPhone 4 were crashing and the battery life run out very fast.
The only solution worked for me was to remove all mail accounts (Exchange/Gmail) from my iPhone (in settings) and then add them back.
The crashing were stopped! also the battery was back to normal.
I found the solution by first looking at the crash logs (in IOS 6). you can find them at Settings -> General -> About (at the bottom of the About menu you will find the option that opens the logs).
There i saw many logs about Low Memory crash. 99% of the logs were pointed that the largest process (use the most memory) during the crashes is "dataaccessd".
I search in the web and found that this process is a deamon process that reponsible the Mail accounts (like Exchange/Gmail) and contancts list.
I've installed the app "System Status - activity monitor" which shows important system info like CPU usage, Memory usage and running processes.
Before apply my solution (deleting the mail accounts) i saw that the CPU usage was very high which consume the battery very fast. Also i saw that the memory (RAM) was run out.. which probably what cause the crashing..
After deleting the mail accounts (at Settings -> Mail, Contacts, Calendars) i check again with the System Status app, and saw that the memory and CPU were back to normal.
Adding the mail accounts back, still everything work ok
Hope this solution will help you too,
Enjoy!

Wifi disconnect wen The display turns off

Similar Messages

Maybe you are looking for