Wifi loses connection when sleep

why does my wifi lose conection after sleep mode on Lion 10.8.5

Try the basics first:
Change your router channel number. Most times this works & is all you have to do.
Disconnect & reconnect your modem. unplug it for about 10 seconds. Plug it back in. Do the same for Apple’s routers. Wait for everything to reboot.
System Preferences>Network
Click the Assist Me button.
In the next window that pops up, click the Diagnostic button & do the necessary.
Research Knowledge Base for network problems that pertain to the OS that is currently installed on your computer. See these basic networking KB Articles: http://support.apple.com/kb/HT1401 AirPort troubleshooting guide
http://support.apple.com/kb/HT4628 Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT2712 Using network locations in Mac OS X
Manually provided DNS server addresses are higher priority than DHCP's
http://support.apple.com/kb/HT1714 Solutions for connecting to the Internet, setting up a small network, and troubleshooting
============================
What to do when you can't connect to the Internet
Also, run the Airport Utility app which is located inside the Utilities folder.
=====================
If using a Linksys router, contact LinkSys Customer Support and/or post in their forums.
If using Apple's Airport, please re-post over in one of the AirPort Forums.
================
Lion 10.8.5
No such animal.
Lion = 10.7.x
Mountain Lion = 10.8.x

Similar Messages

I have an iMac (Mid 2010) and am running 0sx 10.8.5 and the WiFi always loses connection during sleep mode. I have seen numerous different solutions none of which seem to work. Can anyone help?

I have an iMac (Mid 2010) and am running 0sx 10.8.5 and the WiFi always loses connection during sleep mode. I have seen numerous different solutions none of which seem to work. Can anyone help?

Test after taking each of the following steps that you haven't already tried. Back up all data before making any changes.
1. Make sure the network is on the preferred list by following these instructions. It's important to read the article carefully, as it's the starting point for any further efforts to solve the problem. If you skip any of the steps, the problem may not be solved. Make sure the box marked
          Remember networks this computer has joined
is checked.
2. Follow the instructions in this support article under the heading
          Symptom: After restarting or waking from sleep, my computer might not connect to the Internet
3. Reset the PRAM.
4. Make a note of all your settings for Wi-Fi in the Network preference pane, then delete the connection from the connection list and recreate it with the same settings. You do this by clicking the plus-sign icon below the connection list, and selecting Wi-Fi as the interface in the sheet that opens. Select Join other network from the Network Name menu, then select your network. Enter the password when prompted and save it in the keychain.
5. From the Location menu at the top of the Network preference pane, select Edit Locations. A sheet will drop down. Click the plus-sign button to create a new location. Give it any name you want. In the new location, set up the Wi-Fi service with the same settings you used before. Click Apply and test.
6. Launch the Keychain Access application. Search for and delete all AirPort network password items that refer to the network. Make a note of the password first.
7. Repair permissions on the startup volume.
8. Turn off Bluetooth and test.
9. Reset the System Management Controller.
10. This step shouldn't be necessary, but has been advised by Apple Support in some cases, apparently as a workaround for a bug. Open the Energy Saver pane in System Preferences. If applicable, click the padlock icon in the lower left corner to unlock the settings. Enter your administrator login password when prompted.
Select the Power Adapter tab and uncheck the boxes marked
          Wake for Wi-Fi network access
and
          Enable Power Nap...
if present. Then, if the computer is a MacBook, select the Battery tab and uncheck
          Enable Power Nap...
11. Reinstall OS X.

BT Keyboard Loses Connection When Waking from Sleep Mode

I'm running Windows 7 on a late 2009 27" iMac and my Bluetooth keyboard keeps loses connection when I wake my computer from sleep mode. Usually the only way I can get it back is my resetting. Anyone know of a way to fix this? Any help would be great appreciated.

If the MBP doesn't wake when you open the lid but does when you press any key afterward, do this:
Applications > Utilities > Terminal
Copy and paste the following text in the Terminal window:
*sudo pmset lidwake 1*
You'll be asked for your admin password. Type that in (Note: the password will not be displayed as you do so). Press Return, and quit the Terminal. Close the MBP, wait for it to sleep, and open it again. Does it wake now?
If you want to change it back so the system doesn't wake when you open the lid, repeat the procedure, but this time type or paste:
*sudo pmset lidwake 0*

My magic mouse loses connection during sleep

My Magic mouse loses connection during sleep mode. I also get error message my external usb storage drive was disconnected improperly. I have to unplug and plug in drive generally, sometimes it is still present. For the mouse I generally turn it off and on and allow it to be found again.

This is a late 2009 imac.

My trackpad loses connection when left idle

My trackpad loses connectivity when left idle - anyone know why this is happening & how I can rectify? Grateful for any advice.

Nothing else I can think of to try.
You might want to take everything in for testing.
Barry

IPad WiFi/3G dropping WiFi connection when sleeping

Just recently, my IPad just started dropping it's wifi connection when it goes ton sleep, and it isn't automatically reconnecting. This is my home network, and previously it did reconnect on wake. I have open preferences and manually reconnect every time I wake the iPad.

OrganicHippy wrote:
Ok. I am surprised I haven't heard this from you smart people:
*The wifi problems are specific to certain types of routers!!!*
Example: My Pad works like a champ at work. The router there is an old Linksys G.
It works like crap at home. At home I have a newer Belkin N/G.
That's why some people have problems and some don't: It depends on the router.
So...My question is: What is the best router for an iPad?
I'm willing to go out an buy it; I just want someone to tell me the best one!!
Is it really necessary to spam so many threads with this?
Message was edited by: Joe5150

My Photosmart Plus printer seems to lose connectivity when in sleep mode, how can I fix this?

My new photosmart plus appears to loose it's connection when it goes to sleep. At least the printers status page online says it's not connected, even though it is visible in my router and the blue light next to the antenna of the printer is on. It also appears to be connected when I poke around in the printer's settings, but if I want to print something from an app or via e-mail I have to run the wireless wizard again, select my netgear and enter the password. Once connected I get a screen where I supposedly can skip printing a report, but that does not work either, it prints no matter what I select, waste of paper and ink.
I searched around but found no solution that would work for me.
Tech info:
wireless conection to my cable modem with Netgear router
Macbook pro and an older HP laptop are in use.
Security is WPA2-PSK [AES]
I like the machine a lot, but this is rather anoying, what can I do to keep the connection when the printer sleeps?
(edited to add security info)
This question was solved.
View Solution.

Does the printer not wake from sleep for both the Mac and PC?
You may want to try setting a static IP address for the printer:
- Print a Network Config Page from the front of the printer. Note the printer's IP address.
- Type that IP address into a browser to reveal the printer's internal settings.
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. Enter the current IP address.
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Leave the gateway and DNS blank. Click 'Apply'
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you may need to redo 'Add a Printer' using the new IP address.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

My wifi loses connection to my phone and laptop at the same time every 30 mins or so.

Hey all.
I have a WRT160 V2 router with firmware v2.0.02. I have had the router for years without any problems. A few months ago I have started to see an issue where I lose connection to my internet on my laptop, and wifi on my phone at the same time. I have wifi calling on my phone and it disconnects also at the same time. All of a sudden, everything will stop working, then about 40 seconds later, it all works again. I lost the connection maybe every 30 to 60 mins
Does anyone have an idea what can be causing this issue? Thank you.
It is really annoying because I rely on wifi calling for my primary phone, and I end up getting cut off when talking to people. BTW wifi calling is for all tmobile phones, but also normal wifi to surf the web on my laptop and phone drops too at the same time.

I would suggest that you isolate the problem. You may start the isolation by connecting a computer directly to the router (hard wired connection). Observe the connection for couple of hours. If the connection is stable, problem might be on the wireless settings of the rotuer. If the connection is not stable, do further isolation. Connect the computer directly to your modem. Observe the connection for couple of hours. If the connection is not stable, call your internet service provider. If the connection is stable, problem might be on the router itself. Upgrade the firmware first (firmware available in the website: Ver.2.0.03 Build 9). After the upgrade, reset and reconfigure your router.

Apple TV loses connection after sleeping

My Apple TV had virtually no problems with a connection when being used, but has this curious quirk of losing it's connection after an extended sleep period. It seems as if it sleeps for more than 8 hours, it will no longer be connected to my network. Viewing the settings for the Apple TV, it shows that my connection should be working and has full strength, but doing a test results in nothing happening. My options are restart or drop connection and input my network password again. This gets really annnoying, because almost everytime I want to use it, I have to do either of those things first. Are there any internet settings I can chnage so that this stops happening?

Actually same goes for the iPhone after charging it when I sleep, next day, have to turn wifi on and off to get the connection to work properly.

Magic Mouse Losing Connection When Sleeping

My magic mouse loses its connection when my iMAC goes to sleep. I have the preferences setup to allow my iMAC to be awakened by bluetooth devices... Any suggestions?

Let me add, that this happens when the machine is asleep and all user are logged out... I have to use the wired key board to wake the machine up and then I can log in at the user log in prompt.

This may sound dumb, but is there an app or a monthly subscription to carry wi-fi or internet connection. so i dont lose connection when i leave my house. want internet connection at all time

I have an ipod touch 5th gen. storage capacity is 27.9 / 23.3 available. IOS 7.1.2 model # ME978LL/A. My question is, now this may sound dumb. But i was wanting to know if there is a app or a monthly subscription to have internet connection or wi-fi at all times instead of just shutting my ipod off very few apps work without internet connection almost dosen't seem worth 300 dollars. THANK YOU FOR YOUR INFO.

Your internet connection depends on access to a wifi network. When you leave your house you go out of range of your own network, so the only way to connect is to find a free or paid public wi-fi service in the location you are in at the time; the alternative is to use your iPhone for what is called 'tethering' (providing a wifi signal you iPod can connect to) but it you have an iPhone you would want to use that anyway (and many service providers don't allow it - in any case it comes expensive as you are using a mobile data connection).

Extreme Base Station Loses Connection When Slept

To improve overall system security, I recently changed my account from an Administrator to a Standard Account, and created a separate Administrator's Account. Now whenever I or another user start up from sleep mode, enter our standard user password, the airport connection is lost and an admin password is required to get it going again.
Is there any way to ensure that the connectivity is not lost when sleeping, or it is automatically reconnected when awoken from sleep, without the use of an Administrator's password?
2GHz dual G5, ATI X800 XT, 2 X 500Gb HD, LaCie D2 1Tb, 3.5Gb RAM , 23" HD Panel Mac OS X (10.4.9) Airport Extreme 802.11 (n) / 802.11 (g) on on G5 Mac Pro

djeddy, Welcome to the discussion area!
When switching the cable modem's Ethernet connection from the MacBook to the AirPort Extreme base station (AEBS), you should power off the cable modem for a minute or two (often longer).

Discoverer Plus loses connection when COLLAPSING in Hierarchy!

I am getting an error saying that' Discoverer connection is lost. Please contact your admin" when I am collapsing hierarchies. Did you ever encounter this kind of error ever? I have like 6 levels of hierarchies(date hierarchy, like yr,season, quarter etc)...So one hierarchy is Company ->Year and other one is Year->Season->Quarter so on.... So when I collapse one by one level its ok... but when i do it all at once from the top, i.e Company, it loses connection!!
Is it some kind of a bug???
Thanks a lot,
rocky

Hi
Well it does sound like the hierarchies are to blame, although to be honest with you I've seen Discoverer losing its connection for something far less trivial than that. The most common reasons for losing a connection are network issues and being out of memory either on the Discoverer client or on the server. I'd suspect that memory is an issue.
Now, your second issue relates to the use of those hierarchies. Are they perhaps date hierarchies as opposed to item hierarchies? If so, whilst they are really quite clever, they do tend to cause more problems than they solve. Personally, if you are using date hierarchies, I would create a materialized view or table of your fiscal time and then create one folder for each date in your folder. I'd drop the Oracle date hierarchies in a heart beat but this is easier said than done.
Does this help?
Regards
Michael

Does WiFi stay connected when charging iPhone

I've noticed lately that when I wake my iPhone from standby when it is plugged into a power source (charger or usb on my computer) that the WiFi connection is already there (the phone has been on standby overnight in the case of the charger). I get the impression that the iPhone is maintaining the WiFi connection when it has external power, but have not seen any references to this behavior. I have noticed this since at least 3.1, don't remember if earlier or not.
My iPhone is up to date with OS 3.2.1.
This is not a problem, just curious if anyone else is seeing this behavior?

Just wanted to throw what I have seen in. I have an AEBS in my house. When my phone is in low power mode with screen dark and I wake it up, the symbol moves from 3G to Wi-fi symbol. When I open my Airport Utility, it shows me the number of users. Unless I actually have Safari on the iphone open and running, it only shows one user (my MBP). When I open Safari on my iphone, then I show 2 users. If I close Safari, it moves back to one user...

HT1365 just installed a new wireless router (cisco linkseys E1200) and our apple laptops connect fine on one floor but lose connectivity when moved to another. Other non apple laptops & Ipad connect with no problem no matter what floor they are on

We just installed a new wireless router to our main PC. It's a Cisco Linkseys E1200. All other wireless devices were able to connect without a problem, including my Ipad. We have 2 Macbook Pro laptops. They both connect just fine when on the same floor of our house as the router, but when we take them upstairs to the 2nd floor of the house, they lose connectivity and it states the wireless password is not the correct password. All other 2nd floor laptops have no problem at all with connectivity no matter where they are in the house. Please help- my husband is on the verge of selling Apple if that cannot be remedied.

This would not be a security issue symptom. I would consider checking for sources of wireless interference HT1365
Trying changing the radio channel on your wireless network.

Wifi loses connection when sleep

Similar Messages

Maybe you are looking for