WiFi MBSSID and MAC filtering

Dear Sirs!
I use Cisco AiroNet and have multissid WiFI
What can I filter users by MAC address only on specific SSID?
Thanks!

Mac address-table xxxx.xxxx.xxxx static
vlan ### drop
In this sring, xxxx.xxxx.xxxx it is allowed MAC?
and vlan ### drop it is entered in global config?
Thanks!

Similar Messages

  • AP1242AG WPA and MAC Filtering problem

    Hello,
    Presently I managed some AP1242AG in ofiice area
    I need implement WPA and MAC filtering.
    I found what :
    In IOS 12.2(13)JA branch IOS and before, MAC authentication was supported
    in conjunction with WPA.
    In 12.2(15)JA and above, configuring MAC authentication with WPA does not
    work. MAC Authentication passes everyone through.
    I can't found IOS 12.2(13) in Cisco site.
    Can anybody help me and give link to download 12.2(13)JA ?
    Thanks.

    Also when I acivete MAC filterring
    access-list 700 deny   0024.d7ed.2204   0000.0000.0000
    access-list 700 deny   0000.0000.0000   ffff.ffff.ffff
    dot11 association mac-list 700
    dot11 ssid zero!v
       vlan 390
       authentication open eap eap_methods
       authentication network-eap eap_methods
       authentication key-management wpa
       wpa-psk ascii 7 14531708030A2E1A3108212127015644
    The WPA is working but MAC filtering not reject
    IOS Ver.
    Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.3(11)JA1, RELEASE SOFTWARE (fc2)

  • E1200 - Ports not working and mac filtering problem

    If there was a way to give negative stars to this router, I would. As it is, the minimum rating I can give this product is one star, and that's one star too many.
    I was upgrading from the WRT54G, which is an ugly thing to look at, but a reliable workhorse nonetheless. I turned that in to a downstream switch in my comms hub.
    On the E1200, I flashed the latest firmware, used different Cat5 cables, and different laptops before committing to hating this product.
    The first time I reached out to Amazon, the Amazon rep gave me a Cisco number to call. Turns out, that's some shady mortgage refinance hotline. Try it for yourself! 1-800-666-1771.
    Now, the rant -
    1. Two out of four wired LAN ports don't work: What can be the fix for this?! The activity lights on ports 3 and 4 blink and suggest data transfer is taking place, but the wired laptop simply can't acquire an IP address and access the internet. Same result when I connect my Panasonic Blu-Ray player to ports 3 and 4. None of the Viera Cast features load.
    2. MAC filtering unreliable: The wireless routing works somewhat reliably, if and only if, one settles for the most basic security. If I only choose a password and WPA2 protocol, things work fine. If I add another layer of security (in my case, enabling MAC filtering and only PERMITTING gateway to listed MAC IDs), things break down. As soon as I disable MAC filtering, wireless access to authenticated clients is restored.
    3. Cisco customer service: The censored world we live in, compels me to criticize politely. TERRIBLE. Cisco website is unintuitive, and frustrating. There's no easy way to register your purchased product. The Cisco "registration" is intentionally misleading and deceptive. For all intents and purposes, it's just an information gathering tool for Cisco. Don't bother registering there, unless you love the idea of storing your personal information on their servers. Their phone-based customer service is apathetic and uninterested. My rep was so distrusting of my intelligence and motor control, that he simply wouldn't believe that I had selected "PERMIT" and not "PREVENT" as the option under MAC filtering. After he asked me the same question for the fourth time, I raised my voice, and he gave up the idea of checking for the fifth time.
    However, this review is a tale of two companies. I reached out to Amazon again. This time, I got a rockstar in the shape of Leanne C! She was incredibly helpful, and understanding. What's more, she set up my return without any hassle and this Cisco dud is on its way back. I'm a big fan of Leanne's and my confidence in Amazon is restored.
    I'm sure that i received a lemon. I've never had problems with Linksys products. Maybe others' experience is different from mine.

    In your case as port numbers 1 and 2 does not work, what you could have done a loop back test. To perform a loop back test you need to take an ethernet cable, connect one end of that cable to internet port and the other end to the non-working port on the router. If you get the led to glow on both internet and the respective ethernet port that indicates that the port is working fine.
    It could also be a sychronization issue between the above mentioned lan ports and the lan card of your computer. As a part of trouble shooting you can try to reduce the card speed of your lan card. Following are the steps to reduce the speed of your lan card.
    START--> right-click My Network Places and click Properties
    right-click on the device manager and click properties
    Click on the CONFIGURE button
    Select the ADVANCED tab and in the box under the header property select "speed and duplex" and change the value on the right to 10 mbps half duplex. A restart would be recommended after performing these steps.
    In the second half you said that after enabling the mac filter option the internet breaks down. Here, do you mean to say that the computer
    gets disconnected from the wireless network or it stays connected with a valid IP address but without an internet connection.
    Well, it is an unusual issue however you could have reset and reconfigure the router as you got the latest firmware upgraded on it.
    Steps to reset the router:
    Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. Power light should blink when you perform the reset process.

  • Mobility groups and MAC filtering

    We have a 4402 controller and we are doing MAC filtering. We have reached the default number of MAC addresses, 512. It has been recommended that we add an additional controller instead of increasing this past the default. Three questions:
    1. Is there an increased (enough to impact performance) load placed on the WLC if the limit of MACs is increased, say to the max of 2048?
    2. If we add an additional controller, configured in a mobility group, how do we configure the MAC filter to load balance? Or do we have to configure the same MAC table on both controllers? Which leads to....
    3. Is there a benefit to adding another controller as far as MAC filtering is concerned?

    As it stands, you would need to manually replicate internal mac filtering database between two controllers, so you're not gaining much with the second controller. As regards to increasing database size and what effects it will have, I don't have an educated answer for you, sorry.
    Regards,
    Roman

  • Smart Wifi iOS App - MAC Filtering defaults to DENY!

    So, the issue I'm having is pretty simple and it's an inherent design issue in the iOS app because it doesn't happen with the web inteface for my router.  I have an EA6500 router and when using the iOS app with an iPhone5s, once you "add a device" to the MAC filtering list it automatically turns off the MAC Filtering when the new device is added.  Then when you turn the filtering back ON, it automatically defaults to "DENY" thus kicking all wireless devices from the router, including the iPhone!!!!!
    So I have to go to the router in the basement with my laptop and connect to it with an Ethernet cable to simply change the checkbox to say "ALLOW" devices instead of "DENY" devices.  PLEASE FIX THIS ASAP!!!!  I use this feature at least once a week and it's a pain in the A$$ when you have to go to use a laptop each time you want to modify the filtered list.
    Thanks!
    My devices:
    EA6500 Smart Wi-Fi Dual-Band AC Router with Gigabit and 2x USB
    Firmware version:       1.1.28 (Build 146072)
    iPhone5s
    iOS 7.0.4
    Linksys Smart Wi-Fi 1.4 149827 (app)

    There could be a problem with the app perhaps. You can uninstall the app and reinstall it. That could help.

  • Mac can't see new printer-told to Disable Airport Extreme Firewall and Mac Filtering...

    I have a new Epson WF-3520 AIO printer. I run Mac on OS X 10.5.7.  The printer appears to be properly set up to run wirelessly but it doesn't show up as a choice to be added to my list of available printers.  My Mac just doesn't see it.  After trying many things Epson's tech support told me to call Apple and find out how to disable the Airport Extreme's firewall as well as Mac Filtering.  I went into the Airport's utility and just got lost in knowing exactly what steps I need to take to do this.  Also, I'm somewhat dubious that this is really what needs to be done in the first place and I'm wondering if he simply wanted to get off the phone....  All advice welcome!  Thanks. Stephanie

    Forget it.... My suspicion was correct.  I was talking to an idiot.  Problem resolved by me.  Unrelated to Airport.
    Forgot to install a piece of software... duh!!!

  • WAG54GS CD and MAC Filtering

    Hello,
    1)  Where can I obtain a Install CD for my WAG54GS Router?
    2) I have had the WAG54GS in use for some years now, and more and more computers and devices are to the router.
    Recently my Printer (HP 6500) often tells me that it cannot obtain an IP address  but it does t "see" the SSID Router name.)
    Error roughly translates (German) to
    Your Router uses MAC Filtering. So a Connection the HP Printer may fail.
    I must either deactivate the MAC filer or add the Printer MAC Address to the allowed list.
    I am unsure how to do this.
    Any help on both of these comments.??????
    NT

    OK, thank you.
    I keep losing IP addresses now fron my PC's as well a my printer. Usually a router re-boot helps.
    The thing  I did not like about this WAG54GS  is that there is no power fail re-start.
    Have you any idea why losing the IP address occurs. Note that the SSID is being recogonised and with a healthy
    signal level.
    However
    A am sending on Channel 1 but there is a TP-LINK 504132  Router in my neighbourhood that is on channel 1
      (2,412 GHz) and is sending 802.11n and seems to be tranmitting a much higher speed than me.
    I wonder if this could be causing problems.
    Regards

  • EA2700 bridging and mac filtering

    I have a EA4500 as a main router and a EA2700 router connected to it (wire) in bridging mode.
    On the EA4500 I use mac filtering for the wireless connections.
    My problem:
    If a device connects wireless to the EA2700, the EA4500 see this as a LAN connection and thus the MAC filter is bypassed.
    Can this be solved?

    You can try this, bridge the 2700 router and use the following LAN-to-LAN configuration to see if the 4500 sees the device correctly:
    http://www.northshore-it.com/tips/how-tos/cascade_linksys/#LAN_to_LAN
    It's possible that the design and detection behavior of the 4500 with the use of a wired 2ndary AP maybe how it's detecting the client devices since it's connected wirelessly to the 2700 however when it goes thru the 2700 to the 4500, it's over a LAN wired connection and thats what the 4500 is seeing. 

  • Guest networking and mac filtering

    I have a dual band airport extreme that I've purposfully kept at an old firmware revision because I have mac filtering enabled and also want to have guest network enabled. Somewhere around version 7.5 a bug was introduced that applied the mac filtering to both the private and guest SSID's. I found a number of posts from back then about it, but can anyone tell me if it has since been corrected in the more recent releases?
    Thanks
    Matt

    Somewhere around version 7.5 a bug was introduced that applied the mac filtering to both the private and guest SSID's. I found a number of posts from back then about it, but can anyone tell me if it has since been corrected in the more recent releases?
    No.  For what it's worth, Apple Support does not call it a "bug". They call it a "feature".

  • Wifi Sync and mac sleep

    My 2011 Mac Mini is usually asleep. Will wifi sync wake it up and then shut it down after? I am using a time capsule for the router and the mini is wired. Would it work any different if the mini was on wifi?

    Are you running Lion on the Mini?
    If so, perhaps try having "Wake for network access" selected, as per the following document:
    OS X Lion: Share your computer’s resources when it’s in sleep

  • Connect wifi vista and mac to internet

    moving to MAC platform and looking phase windows out of my life. problem is wife uses vista laptop and want to keep her connected to internet.
    current setup is Linksys wireless router. 1 Toshiba laptop running vista home premium and 1 dell laptop running XP. I am looking to buy macbook and not sure if I can just connect to wireless router and have it work?

    *"I am looking to buy macbook and not sure if I can just connect to wireless router and have it work?"*
    Sure you can. Why not?

  • Wifi macbook and mac pro desktop

    Hi, not sure if this is the right place to post this. I have a Macbook that can see my router and connect no problem. My Mac Pro desktop computer is far from the router and I want to connect wirelessly, but the Mac Pro can't see the router, even though it has an airport card and is right next to the Macbook. I'm not too wireless savvy — any help would be appreciated. Is it possible for the Macbook to share it's connection with the Mac Pro? I need a quick fix that doesn't involve running a network cable across the house...
    Thanks!

    OK, so now you know the wireless card is working, or appears to be working because you can see other networks.
    The next task is find out if it will connect to your network, and to do this, you'll need to move the desktop maybe half the distance to the router and see if you can get a connection.
    If you can, the area where you had the desktop will need a stronger wireless signal. You don't mention what type of router you are using, so using an AirPort Express to extend the wireless signal can't be recommended..yet..since it may not be compatible with your router.
    If you don't want to move the desktop and have to have a connection in the next few hours, get a pair of ethernet powerline adapters. This will be almost as good as a straight ethernet cable and far better than wireless. The adapters (one at the router end and the other at the computer end) use the wiring within your house to transport an ethernet signal.
    Best Buy will have a selection or look under "ethernet powerline adapters" in google.

  • WLC 4402 Web Authentication, Mac Filtering and Layer 2 Seciruty

    Hi All,
    I have configured web authentication and Mac filtering on WLC 4402 for my wireless network and its working fine. I wants to configure layer 2 security for the same Wireless network without pre shared key. Could you please advice how to configure layer 2 security with web authentication withour preshare key.
    Is there any security issue with web authentication and Mac FIltering only? My concern in my wireless network shows open.
    Thanks,
    Kashif

    Hi,
    if you have a ACS, then you can do Web auth Splash page!!! Please refer to the below doc!!
    http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a0080956185.shtml
    Lemme know if this answered ur question!!
    Regards
    Surendra

  • BT Homehub 3 - MAC Filtering

    I can't seem to find any MAC filtering options on the router. The only way i can currently block devices is once they have already connected which is inconvenient. I have a list of wireless devices MAC addresses which i want to block, is there any way to do this or shal i ditch the home hub and buy something else?

    You must have a lot of people in your house
    The only other option is to use a different router, or use a separate wireless access point, and turn the home hub wireless off.
    I use a TP-Link WA701ND, which has full MAC control, and even multiple SSIDs, each with their own key and MAC filtering.
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • WLC Flexconnect with AAA and MAC authentication

    hi,
    i am having cisco WLC with 7.4.121 version and i am having remote side access points to be connected to this controller and remote access point will have different vlan on the remote side itself.
    my question is i am having  Radius authentication for the clients who are all connecting from all the access points and MAC filtering also.
    My radius server is placed in the HQ where we have WLC. which method of flexconnect switchign will give be both AAA and MAc filter options to be working.
    one more question,
    is it possible to make each AP seperate MAC filters On the WLC.
    thanks
    cyril

    If you are planning on doing machine authentication i.e authentication of machine with username password by the AAA server at then this is possible using flexconnect local switching enabled provided you have your AAA server accessible via the local VLAN at the remote site.
    In case you are planning on doing mac-filtering using WLC and username/password authentication using AAA server then this cannot be achieved when you enable Flexconnect local switching as you do not get an option to configure the mac-filtering on Flex-connect groups.Hence you would need to use central authentication.
    Actually the best option for you is that you either deploy a local site AAA server and do both the authentications via your radius server or use Central authentication with Flexconnect APs incase this is not feasible.
    Hope this clears you doubts!!!
    Note: Please do not forget to rate and accept as solution incase the post is valid.

Maybe you are looking for

  • Photoshop CS5 on Macbook Pro 10.6.8 Crashes

    All of a sudden, since this morning, my Photoshop has been crashing and I cannot figure out why. Could a file I'm using on photoshop be corrupt? Please help! I have reinstalled, deleted preferences, gotten rid of MM fonts. I do not know what to do an

  • Programs will not open up

    I installed a new hard drive a Hitachi T1. i installed the OS Tiger to this hard drive then copied over the data from the 160gb hard drive during installation. I cannot get applications to open up. The one I can get is Opera. Safari or Firefox and It

  • HT2493 I have a problem with the 3rd step of the Guide for personalizing icons

    I have a problem with the 3rd step of the Guide for personalizing icons: when i click on the little image of the icon in the Get Info window it doesn't come out any command to choose in order to copy it.. is that a problem with mountain lion? where i

  • Unable to convert swf files into fla files

    Hi,   I tried using Dreamweaver to convert a SWF file into a FLA file so I can edit it in CS 5.  But when I right clicked the placeholder for the file, it doesn't have an "Edit in Flash"  option. What am I doing wrong? Thanks very much, Rosemary    

  • Load runner11.5 cant be able to replay with large URL request

    Hi I have recorded the application and when replay we are facing the below error  Action.c(259): Error -32993: Internal Error - Invalid mpsfzUrl=07372120->0x68 / mnUrlLen=2646 (max is 2048) in LrwiUrlCrack::_fvConstruct. mbRedirected=1   [MsgId: MERR