Wifi no longer working after downloading BT Fon ap...

I downloaded the new App, but as a result I was losing connection with my home Wifi network.
In the end I uninstalled the App because everytime I tried to surf I ended up on the BT Fon webpage (why?), but it appears to have done something with my Wifi because now I can't connect to my home network at all - it says it's connected but it doesn't load anything. If I switch off Wifi it will load using the mobile connection.
I have rebooted the phone a number of times, disconnected and reconnected the Wifi, and deleted my home network and reconnected it, but it still won't work.
I wish I'd never downloaded the App now!
From reading the reviews it appears this has happened to others as well. Can anyone give me any idea how to rectify this and get my Wifi back, other than a factory reset - I am not a happy bunny!

So the handset browser shows no web pages at all even if you go into bookmarks and select a page?
Have you tried a different browser like Skyfire?
You may have to bite the bullet and reset regardless if all else fails, use HTC Sync to get the important stuff saved.
I have been using the Fon app on the hero and never had any issues with it at all, I have found it to be a handy little app.
Raid

Similar Messages

My Spreadsheet App no longer works after downloading the new ios7 software update.

My spreadsheet app. on my iphone 5 ( that i had been using) is no longer working since the new ios7 update. So how can i solve this problem?

check whether the App is compatible with ios 7, contact the app developer, or wait for the app update.

WiFi no longer working after software update

I have had my iPhone 3g for about 3 weeks. Everything worked fine at first. I was able to connect to my home wifi. After updating the iPhone software - I noticed I could no longer connect. The network shows up and I enter my password but I cannot join. I also noted this at 2 open wifi areas - whole foods and a friends house.
I have rebooted the modem, rebooted the phone, reset my network settings, and restored the entire iPhone. Nothing has worked. I spoke to Apple support and it sounds like they will send me a new phone...but I feel like this can probably be resolved with the phone i have, TIA!

Hi erik,
Does the iPhone have a Wi-Fi address? If not the issue and possible resolutions may be in this article: http://support.apple.com/kb/TS1559
Does the iPhone get an IP address after joining the Wi-Fi network?
Does the iPhone join and get a valid IP if wireless security is disabled?
Jason

Wifi no longer works after update mountain lion

Ls,
I've updated my MacBook Pro to Mountian Lion yesterday.
Ever since the update I've lost the ability to use the internet over Wifi.
The system shows a check mark on the left of my network list, however there is no outside connection.
I have ran the assistant (assist me...) to trouble solve. My modem has been reset.
My iPad, iPod and Apple TV can all connect without a hitch. leaving me no choice but to ask my question here.
I was hoping that this problem had been posted previously so I would not have to expose my nowbness
Looking forward to an answer!
Kind regards,
Reese

I Read this sollution elsewhere on these forums and found that this worked for me.
However, the "load" time in Safari is not as fast as it used to be. Might be due to some router setting.
Solution:
For all the Dutch users that have a KPN Experiabox router:
1) go to http://192.168.2.254
2) Username: KPN Password: leave empty (You might have changed this yourself)
3) Go to Network (at the top)
4) Go to WLAN (at the left)
5) Set as follows:
Enable WLAN: Enable
Mode: IEEE 802.11g Only
Channel: 7
Transmitting power: 100%
Enable WMM QoS: Disable
This fixed my wifi problems. Good luck

Project no longer works after downloading AIR 3.4

My AIR project built using sdk 3.5.0.12683 was all working fine with AIR 3.3, but now I've downloaded 3.4 it won't load. The background AIR window opens and that's it.
Is there a way to reinstall AIR 3.3, while we try to find out what change in 3.4 is affecting our code.
Doug

Wrong, maybe everybody else is not just downloading and instaling AS IS, but rather downloading and saving these AIR Updates so if things do not go like planed they will be able to rectefy the problem! On the other hand if you would use Flex 4.0 onwards and still use the mx as I do then you would have maybe more likely not the problem you encounter right now with Flex 3.5, and as I do use Flex 4,0 with mx only and all my web or AIR Apps (96% with modules) are all working very well with AIR 3.4! regrds aktell2007

Wifi no longer works after 7.1 upgrade

verizon/frontier router. tried multiple fixes got it to work once for 5 minutes. usually says unable to access. i hate upgrading my phone it always something. Samsung coming out next week..... Anyone got any fix that has a good sucess rate? resets, airpplane ode, forget netwrok all fail.

I Read this sollution elsewhere on these forums and found that this worked for me.
However, the "load" time in Safari is not as fast as it used to be. Might be due to some router setting.
Solution:
For all the Dutch users that have a KPN Experiabox router:
1) go to http://192.168.2.254
2) Username: KPN Password: leave empty (You might have changed this yourself)
3) Go to Network (at the top)
4) Go to WLAN (at the left)
5) Set as follows:
Enable WLAN: Enable
Mode: IEEE 802.11g Only
Channel: 7
Transmitting power: 100%
Enable WMM QoS: Disable
This fixed my wifi problems. Good luck

Dreamweaver 4 no longer working after downloading files created with MX

I downloaded files that were created with Dreamweaver MX to
my pc in order to update them for a new client. I've been using
Dreamweaver 4 and now I cannot even open Dreamweaver 4. Luckily I
also have Dreamweaver 8 installed and can view all the files in the
site from there, but what would have caused Version 4 to generate
errors upon trying to open? It starts to open and I can see that
the properties panel is disabled and then I get the error message:
"Dreamweaver has encountered a problem and needs to close. We
are sorry for the inconvenience." I've sent the error report to
MS...
Any thoughts other than to use Version 8 from now on? Since
I'm a designer, I do have quite a few client sites that I'd have to
reset the remote site info for...
Thanks.

a guess- you also downloaded the .mno design note files.
There should be a technote on this-
It talks about contribute 2, but it's same exact issue with
MX and newer
Dreamweaver 4 crashes on Contribute 2 sites
Issue
Dreamweaver 4 crashes whenever it connects to a site that has
recently been
accessed by Contribute 2.0, 2.01 (Windows) and Dreamweaver MX
2004.
Reason
Contribute 2 and Dreamweaver MX 2004 design notes on remote
server or local
site folder are not compatible with Dreamweaver 4.
Dreamweaver 4 tries to
read these files and crashes when it cannot.
steps to fix are next- link below.
Permanent Link:
http://www.adobe.com/go/tn_19048
or
http://kb.adobe.com/selfservice/viewContent.do?externalId=tn_19048&sliceId=1
Alan
Adobe Community Expert, dreamweaver
http://www.adobe.com/communities/experts/

Md5 reborned hasher 0.9.0 no longer works after firefox update to version 20 ,redesigned download box doesn't give option

md5 reborned hasher which has worked previously no longer works after update to FF version 20 . the redesigned download box doesn't give the option to use the hasher.

If you use this add-on a lot, you might want to switch back to the old style download manager until the add-on's author can bring it up to date. This thread describes how to make the switch: [https://support.mozilla.org/en-US/questions/955204 Got new version, want to go back to previous download box, the new one has no history and doesn't show speed of download, how do I go back?]

Wifi on A1427 is no longer working after 7.2 update.

I have model A1427 Apple TV. Once I updated to 7.2 the wifi no longer works. It will not search and find any networks. If I use the Ethernet cable it works fine. Any suggestions? Solutions? I have restored and restarted the device multiple times.

Apple is not here, and downgrading is not supported for a variety of reasons including security updates.
Your device is only 3 weeks old. Take it to the Apple Store and have it looked at.
Provide any feedback you wish to at:
Apple - Feedback
Cheers,
GB

My ImageClass MF4380dn Cannon Multifunction Copier driver no longer works after installing Mavericks. How can I resolve this?

My Image Class MF4380dn Cannon Multifunction Copier driver no longer works after installing Mavericks. I have checked with Cannon and they do not list my partricular machine among their driver updates. Is there another place to download a driver suitable for Mavericks?

Your MF4380dn is supported by the latest UFR2 v10.4.0 driver that supports 10.9. Here is a link from the Canon Australia web site,
http://support-au.canon.com.au/contents/AU/EN/0100491502.html
Before installing this driver, please remove the MF4380 from Printers & Scanners (unless you have already performed the reset that Carolyn mentions which will remove it for you). Then run the v10.4.0 installer and when it has completed, open Printers & Scanners and add the MF4380.

Epson printer driver no longer working after 10.4.11 update

It seems that my original Epson driver for my Stylus Photo 750 is no longer working after my latest Tiger update. The system does recognise it but shows an exclamation mark behind it and refuses to print with it (the document stays in the waiting line forever). Reinstalling as well as repairing permissions didn´t help. Fortunately the Gimp Epson driver is still working but I have no access to my coloursync profiles with this driver.
I know that many printer drivers need to be rewritten for Leopard (one of the reasons I didn´t update yet) but it is not understandable why problems happen with a Tiger update.
Does anyone know a workaround?
Thanks very much
Wolfgang

I just discovered a similar problem. I have an old Epson SC3000 and under 10.4.11 my computer doesn't communicate with the printer. It's an AppleTalk printer, connected via Ethernet. I tried bypassing my network switch and connected it directly to the Mac-- no go. I then rebooted into 10.3.9 and printing works fine.
I downloaded the driver from Epson and installed it in 10.4.11. When I try to add the printer in the Printer Setup Utility, the machine just hangs-- can't force quit the utility and eventually the Finder even stops responding. It takes a hard reboot to clear up.
I can't say whether or not printing worked in earlier versions of 10.4. I haven't been using 10.4 for very long, and I rarely use the SC3000.

Apogee Jam No longer working after 1.1 update?

My apogee jam is no longer working after updating to Garageband 1.1. I have an Ipad 2 with firmware 4.3.3.
Specifically what happens is:
1. I open the garageband app
2. I select the guitar amp
3. I plug the Jam chord into Ipad (guitar is already connected to cord)
4. Jam light goes green, blue, bright green then green
When Jam light goes bright green, the monitor button in garageband goes dim and doesn't work.
I've tried plugging my guitar in first, then starting garageband, no difference in results.
I have tried turning the monitor "on" prior to pluging in the jam, when I do this the monitor/sound gate window stays open until the Jam bright green goes on, then it disappears and the monitor button goes dim.
Outside the garageband app, the ipad does recognize the Jam in settings, general.
What's worse (for me...) is that I backed up the Ipad in itunes thinking that app data would also be backed up (as I read that in a description of backup). I then deleted garageband from the ipad and then restored it from itunes. Guess what, lost all my songs... Bummed out... Why wouldn't my songs be backed up???
Anyway, any ideas on the Jam issue would be greatly appreciated. I'm hoping I am just overlooking a setting?

Unfortunately, I don't believe that Apple keeps prior versions of Apps available at the store. GB was the first app I purchased there day one of my Ipad, incredibly worth the $, and I did actually look to see if you could go back legitimately.This is just one of the many reasons to JBreak your devices, so that you can go backward if you need to. This is a perfect example of why Apple should make prior versions available, but they think they know it all and never make mistakes, so that will never happen. Again, this is why folks take things into their own hands and why the scene exists. There are plenty of abuses, more than not IMO, but here is a perfect example of how people are screwed and can't use their Jams any longer without a JBroken device. They obviously know that this issue exists, they have employees on these forums. It will be months if ever they fix this issue, because the number of owners of Jam, although in the thousands, is small potatoes compared to the Apple owner universe. I believe it will only be fixed if Apogee is able to put enough pressure on Apple. If you see the Jam removed from the Apple store and GB site you know that Apple is choosing not to fix it, because they won't sell or promote it directly and then have to deal with complaints and returns. But even this will happen slowly...
Actually it occurs to me that Apogee may have to redesign the Jam AGAIN in order to get it working with 1.1 on Ipad 2 and Iphone 4s (devices with the newer processor). I wonder if they will recall or replace the Jams for people who now have Jams not compatible with Garageband. Again, Apple should be posting a warning for Jam owners on the Garageband download page, but that will never happen because Apple doesn't care about small potatoes.
Message was edited by: Rickd3333
Message was edited by: Rickd3333

On 2011 iMac, External Altec Lansing speakers no longer work after upgrading to Mountain Lion. They DO work on a lenovo machine but not my imac

On 2011 iMac, External Altec Lansing speakers no longer work after upgrading to Mountain Lion.
They DO work on a lenovo machine but not my iMac. reset Pram - no luck. took speakers from wife's desktop, they
do not work when jack plugged into my iMac - Sys Prefs "SOUND" only lists "internal speakers/ built in" as available options.
I used my altec lansing speakers on 3 macs including this one for 5-6 years.....now with Mountian Lion I can only get internal speakers???
Ideas? Any/All help would be greatly appreciated - been going nuts with this for 2 days now.

Hi,
When you start Messages fro the first time you are asked for an Apple ID
When this is verified and entered it appears in Messages Menu > Preference > Accounts and is Enabled.
The App should have also picked on on those iChat Accounst you had before.
These should be Enabled if they were when you last used iChat.
Exactly which "Accounts" are logged in can be seen in Message Menu > Accounts and will include the iMessage "Account" and Bonjour.
In the Window menu you will see CMD +0 for the Messages window and CMD+1 for the "Buddies" window which is a combined list at this stage.
Go to the Preferences > General Section and Untick the "Collect all accounts into one list".
This will give you separate iChat type Buddy lists.
You can check if that account/Buddy list is set to Invisible or if in the Preferences > Accounts > Security you have settings that will block some people from seeing you as On line.
You are saying Buddies can see you as On Line which implies they are still sending to your AIM based Names (@Mac.com is a valid AIM Screen Name)
I am not sure from your post if you are trying to iMessage their email IDs thinking they are Apple IDs and that they are using Messages as well.
There is no Buddy list for iMessages side
No-one can tell you are "On Line" until they have your details in the "To" spot in Messages with the correct iMessaged contact info (iPhone Number or Apple ID)
Obviously an Apple ID can be an email or look like one.
In some cases they are also valid AIM Screen Names as well.
In the case or the @mac.com name you may have linked this Apple ID to iMessages as well.
11:31 PM Saturday; August 11, 2012
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 iMac 2.5Ghz 5i 2011 (Lion 10.7.2)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

Application Manager no longer works after I got a new computer.

Application Manager no longer works after I got a new computer.
I moved all of my data from one mac to the other, but the Adobe Suite no longer works.
I tried to re-install it, but it says now that Application Manager is damaged, it keeps sending me to the download page, I download, it starts installing then it says it is damaged, and so on... Got any idea?
Thank you!

1)
Click on the Finder and look for the options listed next to Apple Icon located at the top left corner of the Desktop screen and click on "Go" menu button and select "Utilities" option.
(Applications>Utiliites)
Locate Adobe Creative Cloud and Adobe Application Manager folder under Utilities window and trash both folders.
2) Trash Adobe Creative Cloud from Applications well.
3)
Click on the below link and download & run Adobe Cleaner tool :
Select the option "Adobe Application Manager for Mac OS X 10.6" and then click on "Clean up Selected" .
https://helpx.adobe.com/content/help/en/creative-suite/kb/cs5-cleaner-tool-installation-pr oblems/_jcr_content/main-pars/accordion_container_1/accordion-par/accordion-item-1/accord i on-item-par/procedure/proc_par/step_3/step_par/download/file.res/AdobeCreativeCloudCleane r Tool.zip
4) Click on the below link and download Adobe Application Manager and install the same:
Once the installation process is completed , the installation box will disappear. Then open Application folder and locate Adobe application manager icon and double click on it .
It will start update process and gets updated to Creative Cloud .
http://download.adobe.com/pub/adobe/creativesuite/cc/mac/ApplicationManager9.0_all.dmg
Feel free to post , if you need further assistance

My printer (HP Laserjet 2100) is no longer working after upgrading

My printer (HP Laserjet 2100) is no longer working after the upgrade; it just spits out page after page of error codes and blank pages. I've tried using both the HP driver and a generic driver. This is being accessed over a network. Has anyone encountered this problem after upgrading from Lion?

Hi,
Make sure to install the latest HP Printer Drivers 2.11 update as it should resolve a Postscript printing issue and I believe it will resolve the problem.
You may do so by clicking the Apple icon and then Software Update, you should see the update listed.
For any further issue go to Library\Printers and remove the HP folder, then download and install the following package:
http://support.apple.com/kb/DL907
Hope it helps,
Shlomi

Wifi no longer working after downloading BT Fon ap...

Similar Messages

Maybe you are looking for