Wifi Signal Strength related issue

Hello.
My Hp latop shows only a signal of a bar
or two when placed in the same room as
my wifi router.
It shows a signal of 3-4 bars when placed
very close to wifi router.
Can someone please help with this issue.
This has been a small problem in my home
but now I am moving to a new place and
wifi there is too far from my room. My
laptop doesn't even connect to the internet
over wifi there.

Hi , Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!
I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your HP Pavilion 15-p033tx Notebook and the Wireless connection signal dropping and only giving you a few bars. I would change the Channel on the router. Routers are capable of communicating to your Notebook on several different channels and sometimes this helps. You could turn off IPv6 for the notebook. This has helped others. Fix this problem Microsoft Fix it 50413. Here is a link to help as well. I hope something here helps. Please let me know how this goes. Thanks.

Similar Messages

IPhone 4 wifi signal strength meter not displaying

Please forgive me if there is already a post on this but I've been searching around and haven't found anything exactly like my problem. I'm connected to wifi with my iPhone 4. I know this because in the settings it says I am, as well as I have wifi speeds and the YouTube on my iPhone isn't compressed. However, the wifi signal strength isn't showing up and I just have the 3G icon. If I put the phone into airplane mode and then turn on the wifi it then shows up, but goes away when I turn the airplane mode off. It appears to be a software issue, anyone else having this problem?

Yes, I am having this problem as well.
I have tried the airplane mode 'fix' you tried as well and have the same issue.
I have also noticed that by going into Settings > General > Network and turning off 'Cellular Data' my wifi turns on, I'm at work and I can access the itunes account on our music server (which is usually only available via wifi - to que up tracks in itunes dj etc) however i cannot browse via Safari as it tells me i'm not connected to the internet.
If I turn 3G on and off as well the bars will appear, however it's the same symptoms, and after a minute or so the wifi drops again.
In my wifi settings it shows the wifi as ticked and in use.
I can browse the internet via Safari fine without wifi.
I'm not sure what's going on to be honest, my 3G on iOS4 worked fine yesterday at work....today I'm on my new iphone 4 and have encountered this problem.

TS1559 wifi signal strength problem

my ipad 3 wifi signal strength is very (increase or decrease) and some time its appear one bar
please tell me what i do for its solution
thanks

Could be a router problem or settings problem.
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Wifi signal strength on 2012 Macbook Pro

Well after extensive diagnostic testing with other computers, ipad 2 and 3 generation ipad the Wifi signal strength needs some tweaking on the 2012 13 in macbook pro. The signal and download speed is 1/2 the speed of other devices I own the same distance from my home router. I get 10MB/s typically and my ipad gets close to that using Speedtest.net. When the same distance away from the router on the new 2012 macbook pro I get 3MB/s-4mb/s. Way off from what I should get. I have tried several times at different locations. An older MBP gets similar strength and readings close to 10MB/s.
Is there a tweak or does Apple need to tweak somehow?

BB623 wrote:
yes it got better closer to the router. It's signal strength. Bring back?
I would and keep bringing back until I got one that worked like the other WiFi devices you have.

I seem to have very poor wifi signal strength,is there any way to boost my signal

I seem to have very poor wifi signal strength,is there any way to boost my signal

If you gave some information on what network equipment you are using (make, model, version) and where you are experiencing signal problems it would help in giving advice.

Sudden Decreased Wifi Signal Strength

I recently "upgraded" my internet from 35 to 50, and since then have noticed that my wifi has been absolutely terrible. I can't even use my Galaxy S4 because unless I'm no further than about 50 feet away, it disconnects so many times that I want to throw it through a wall. And now I'm about to go over my monthly data allowance because it never allows me to be connected to wifi.
I walk my dog daily and noticed that before I could make it all the way down the block, a good 100 yards, and still be connected to my home wifi. Now it doesn't even kick in until I'm literally walking in the front door. I've been reading all of the blogs and have seen tons of similar complaints from other customers, but am just wondering if by some miracle someone on here would have some advice for me that will actually work. I've reset the router, changed the channels, turned off my phone's bluetooth....nothing has worked.
Anyone out there have the miracle cure? I'll owe you one!

Since nobody has jumped in with a miracle cure, let me start a dialog with this.
It seems unlikely that your wifi range would change just because you changed speed plans. Do you have another WiFi device, a laptop, etc., that you can check your WiFi signal strength with? As a troubleshooting step, I would want to eliminate the possiblity that it's your Galaxy S4 that has developed a problem receiving WiFi signals.
If you can confirm that your phone is not the problem, my suggestion would be add a 3rd party wireless access point to your network, Netgear, Linksys, etc. While I've had no problem with my Actiontec router, I (and others) have found that its WiFi coverage doesn't measure up to other manufacturers' WiFi devices.

Mid 2010 iMac Wifi signal strength issue

I am having issues maintaining a robust Wifi signal on my 21.5 inch 2010 iMac with 10.6.5 installed.
my symptoms are very similar to what is described in this post:
http://discussions.apple.com/thread.jspa?threadID=2596933&tstart=0
in addition to that I am experiencing the following symptoms:
can't print to HP wireless printer
remote app for iphone doesn't find the iMac
mobile mouse remote app doesn't find the iMac
can't ping the iMac from Windows laptops on the same subnet or from the router itself
accumulation of send and receive errors in Network Utility
these symptoms occur after the machine has been connected to wifi for 30 minutes or so. Turning off Airport and turning it back on temporarily fixes the issue. the Mac firewall is turned off.
as reported in the post mentioned above, signal strength for my Windows laptops and other devices is consistently -25 but the iMac signal strength fluctuates wildly.
One more troubleshooting step that I have taken is to install Windows 7 on a boot camp partition to rule out the iMac hardware and physical location as the issue. While booted into Windows the iMac did not exhibit any of the above symptoms and held a steady -25 strength signal.
Lastly I am using a TrendNet Wireless N Access Point but have also tried an Apple Extreme and Express (both N). I've tried 2.4Ghz and 5Ghz on various channels. I've even tried dialing down to G mode.
I've read other posts about DNS settings, Static instead of DHCP addressing, etc. and none of these has solved this issue.
Thoughts anybody? TIA

Update concerning additional troubleshooting steps that I have taken.
1) did a clean install of OS 10.6.3 onto an external drive and managed to replicate the issue....so that rules out apps, preference files, etc.
2) managed to get a little bit more stability by setting up an Airport Express in 5Ghz mode with Interference Robustness turned on and the multicast rate set at 9Mbps....of course ios devices don't do 5Ghz so I still have to run another AP...so not an acceptable solution.
What else do I need to do to prove that it's a Mac OS software issue?

2g Touch's Wifi signal strength

Ok, about a week ago i posted about getting strange behaviour with my 2g Ipod touch's wifi signal meter: http://discussions.apple.com/message.jspa?messageID=8098190#8098190
I finally downloaded Wifinder (which measures the signal strenght) and find im getting really low readings in comparison to my Imac's wifi. Standing right infront of the router i get a reading of 60 (the scale being from 1 to 100) and in the next room i get a reading of 35-45 where my imac gets around 75. Im not having problems connecting or surfing (the routers if tested are all WEP) but I am concerned with the signal strength. Can anyone give me any reference of the signal with Wifinder on their Ipod Touch? Is the touch's wifi reception significantly lower than other wifi devices?
I might just go back to the apple store tomorrow, still thinking about it though (i hate having to prove to the guys at the store that my unit has an issue).
Thanks in advance
Adrian D

I haven't actually used that app, so I can't speak to its reliability. However, I can tell you that when I visit my parents' house (they live in suburban NJ - tons of houses about a driveway apart from each other) my Toshiba notebook picked up on a bunch of networks, my MacBook picks up on a few less networks, and my iPod touch finds only the one I created with my AirPort base station. So the iPod touch's Wi Fi antenna is certainly not as strong as what one would find in a computer.
CG
Message was edited by: CasperGemini (typo)

Two iPad 2s (Black and White) side by side - diff wifi signal strength

Why would two wifi-only iPad 2s sitting side by side, connected to the same router, have different signal strengths? The 32gb black shifts between 1 or 2 bars and the 16gb white has 3 bars consistently. Both have the same version of iOS (5).
Thanks!

Why would two wifi-only iPad 2s sitting side by side, connected to the same router, have different signal strengths? The 32gb black shifts between 1 or 2 bars and the 16gb white has 3 bars consistently. Both have the same version of iOS (5).
Thanks!

Any apps to measure wifi signal strength?

Want to assess signal strength in various locations. Is there an iOS app or a Mac app to do this?

Where did you get that from? It displays signal strength and noise!!!
iStumbler does display signal strength and noise. I said that it does not display a reading for SNR. Maybe you do not understand SNR? Do you see a column heading for SNR in iStumbler?
SNR is the raw signal data minus raw noise displayed in dBm. The percentages that iStumbler displays are not very useful, but fun to look at.
It appears that you might be able to calculate the actual SNR by using the Inspector feature of iStumbler under the Edit menu, then do the math. Let us know if this works for you. Post back if you do not know how to do this. WiFi Explorer does this for you right on the main page.
SNR Signal Quality Chart
40+          Superior
35            Excellent
30            Very Good
25            Good
20            Fair
15            Low
10            Very Low
5              Not reliable

Problems with reconnecting and WIFI signal strength

Three problmes
1) Weaker signal strength
2) Ipad doesn't connect to wifi after wake up
2) apple.com takes forever to load. Shame.

What kind of AP do you have? What is the FW Version? Is it the latest? What is your network configuration? If you are looking for help you may want to provide more information.

Problems with poor wifi signal strength, need help?

Any suggestions would be greatly appreciated? This is a lengthy explanation. Thanks in advance.
I have a 3rd generation Airport Extreme wirelessly bridged to a 4th generation Time Capsule. I have noticed only mild increase in signal strength. Surprisingly I have only 1 – 2 bars of signal strength when standing next to the bridged Airport Extreme. There are areas of the house that continue to have very weak coverage ranging from 0 – 2 bars depending on the day and others that continue to have no wifi coverage.
The house has Cat 5 cable in all rooms. Most rooms only have a phone jack wired to the end of the Cat 5 cable but two rooms have data ports. All the wires (phone and data) run to the same junction box and are connected to, what appears to be, a simple parallel bridge. (There are a couple unused access points on the bridge. A few years back, I ran an additional line for a phone by simply pressing the colored wire into the corresponding site and the phone works fine)
It was suggested to plug the two routers directly into the data ports rather than have them communicate wirelessly. When doing this, I had no signal at the other end and the phone stopped working.
What is the best way to fix the weak wifi signal problem?
1.     Do I need to tweak my current wireless set up? (FYI, In the Airport Utility, both devices are listed and have green dots)
2.     Do I need to buy an additional Airport Extreme to bridge to the Time Capsule to cover the current dead areas? (unless there is something I should do different in the set up, hesitant to do this, since I have only seen a marginal boost with my current bridge)
3.     Would it be better to use the existing cat 5 cable and create a functional “hard wired” network that I can use to connect the two wireless routers? (If this is the answer, is this something relatively simple that I can do myself or should I hire a professional?)
Thanks again.

The house has Cat 5 cable in all rooms. Most rooms only have a phone jack wired to the end of the Cat 5 cable but two rooms have data ports. All the wires (phone and data) run to the same junction box and are connected to, what appears to be, a simple parallel bridge. (There are a couple unused access points on the bridge. A few years back, I ran an additional line for a phone by simply pressing the colored wire into the corresponding site and the phone works fine)
It was typical awhile back, where you have "whole-house" Ethernet running back to a patch panel to use the cable runs for both data and phone service. This works fine as long as you only wanted 100 Mbps Ethernet (or Fast Ethernet) connections for data. Gigabit Ethernet requires all of the twisted pairs in the CAT-5 cable and cannot share any of those pairs for phone lines.
So any wall outlet that is wired for both phone & data will not provide Gigabit Ethernet ... unless there are at least two CAT-5 cables going to that outlet. I am only mentioning this as to the potential for reduced bandwidth on some of your connections as all of your AirPort base stations are Gigabit capable.
As far as "weak" signals, I am assuming that you have configured all of your AirPort base stations for a roaming and NOT an extended wireless network ... correct? Even if you already have, please review the following Apple Support article to make sure you didn't miss anything. Please post back your results.

"No Service" signal strength related

So I got my iPhone and went through the set up on iTunes. I am porting from Verizon so it told me that they are working on my activation. Anyway, My phone says "No Service" up in the signal strength area. I walked around my house and it did not change. Then I got in my car and drove around and it still say's "no service". Does it say this because the phone has not been activated or do I actually have no signal strength? If so will ATT be able to activate my phone?

I'm wondering that myself. I've been an AT&T/Cingular customer for several years, but recently moved to a location where the signal is weak to the point that I often have to go outdoors to make a call. I'm still not activated, but I've been seeing either "No Service" or - occasionally - a sliver of one bar. Even outdoors. Yikes!
iMac 1.8GHz Intel CD Mac OS X (10.4.10) iPhone?

Why is it "illegal" to write an app that lists WIFI signal strength?

I would be very useful to be able to see which wifi signal near me has the strongest signal and what channel(s) have wifi. I have heard that apple will NOT allow anyone to create an app with those features. Can someone please tell me why?
Thank you
Bruce

Bruce Lomasky wrote:
I would be very useful to be able to see which wifi signal near me has the strongest signal and what channel(s) have wifi. I have heard that apple will NOT allow anyone to create an app with those features. Can someone please tell me why?
Fact:
Several apps in the Apple iTunes app store at one time provided this service.
Fact:
They ALL used a third party library that was not approved by Apple.
Fact:
They ALL disappeared from the Apple iTunes app store.
Fact:
The requisite features are not available in an Apple approved API, Apple's or anyone elses.
Why:
Who knows and who really cares? iOS is Apple's platform and Apple make the rules.
If you don't agree with the rules you can always express your discontent at Apple's feedback site.
As others have said, speculation concerning Apple's past, present, or future decisions is against the TOS.

1.1.1 improves WiFi signal strength?

After upgrading to 1.1.1 last night, I noticed that my iPhone was picking up my WiFi signal in my house in places where it did not pick it up prior to the update.
Is this an unpublished improvement? Anybody else notice this?

mine has gotten worse also and so has my wireless signal , use to have 5 bars now all i get is 3 or 4 and once in a while there is no signal in a spot that i just had 4 bars ????????

Wifi Signal Strength related issue

Similar Messages

Maybe you are looking for