WiFi Throughput worse since upgrading to latest TimeCapsule

I'm using my Time Capsule as NAS to stream movies from. I recently upgraded from a 2nd to a 4th gen TimeCapusle but since then I have problems streaming movies. They constantly need to buffer . I guess the throughput is not as good as before even though the WiFi reception seems to be a bitter better (accoding to the icon in the menubar)
Here's my setup:
4th gen Time Capsule 2GB, Firmaware 7.6, WPA network
2 Airport Express (all "-n") extending the WPA network
HD Movies stored on the TimeCapsule and are streamed to iTunes on my MacBook
This all worked without problems using my old 2nd gen TimeCapsule. My first attempt to solve the problem was to manully define the WiFi channel after looking at all the 55 network in range but this has not changed anything.
Any ideas who I can solve/ look deeper into this problem?
Thanks!
sven

I have tried this however it did not make a difference. I found another user on the support pages that has the same issue.

Similar Messages

Can not sync iPhone 4 since upgrading to latest software release. Keep getting a message that required file can not be found. I've tried restoring several times. I am using Mac PC with the latest software release.

My iPhone 4 will not sync since upgrading to latest software release. I keep getting the error message "required file cannot be found". I've tried restoring several times with no success. I am using a MacPro notebook with the latest software release.

My iPhone 4 will not sync since upgrading to latest software release. I keep getting the error message "required file cannot be found". I've tried restoring several times with no success. I am using a MacPro notebook with the latest software release.

Since upgrading to latest iOS, my WLAN can not see many wifi networks, my friends iPhones pick them up easily. What should I do?

Since upgrading my 4s iPhone to the latest iOS , I now can not see many wi-fi locations beyond my home network. Friends can find and connect to many wifi networks yet my iPhone does not even see them. I can not recall prior to the upgrade whether in the settings whether turning on the wifi was shown as wifi or WLAN however the on/off is now WLAN. Not sure what the difference is. I totally reset the phone but no improvement. Can any body help me?

I have tried this however it did not make a difference. I found another user on the support pages that has the same issue.

Flash error since upgrading to latest Safari

Hi everyone,
Since upgrading my browser a couple of weeks ago (Safari 6.1.2) on my Mountain Lion, I have two very infuriating problems:
The first is a persisitant error message that pops up on most web pages I go to - telling me that www.facebook.com detects that my flashplayer might be out of date. (I do not even have a facebook account - so this is looking a bit dodgy?) I get 3 popups for each page I open, which I then have to acknowledge to proceed. Upgrading Adobe Flash player & restarting has not fixed the problem.
The second problem is that I can no longer do a google search from the address bar - it gives me a cannot connect to the server error - I have to go to google home to do all my searching now....(google is still ticked as default search in preferences)
Any ideas? Is this a problem with Safari software, or is something malicious going on?
Thanks for your help!!

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) on the advice of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
Copy a line of text in this window to the Clipboard.
Paste into the window of another application.
Wait for the test to run. It usually takes a few minutes.
Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin; clear; Fb='%s\n\t(%s)\n'; Fm='\n%s\n\n%s\n'; Fr='\nRAM details\n%s\n'; Fs='\n%s: %s\n'; Fu='user %s%%, system %s%%'; AC="com.autodesk.AutoCAD com.evenflow.dropbox com.google.GoogleDrive"; H='^[[:space:]]*((127\.0\.0\.1|::1|fe80::1%lo0)[[:space:]]+local|(255\.){3}255[[:space:]]*broadcast)host[[:space:]]*$'; NS=networksetup; PB="/usr/libexec/PlistBuddy -c Print"; A () { [[ a -eq 0 ]]; }; M () { find -L "$d" -type f | while read f; do file -b "$f" | egrep -lq XML\|exec && echo $f; done; }; AT () { o=`file -b "$1" | egrep -v '^(A.{16}t$|cann)'`; Ps "${1##*/} format"; }; Pc () { o=`grep -v '^ *#' "$2"`; l=`wc -l <<< "$o"`; [[ l -gt 25 ]] && o=`head -n25 <<< "$o"`$'\n'"[$((l-25)) more line(s)]"; Pm "$1"; AT "$1"; }; Pm () { [[ "$o" ]] && o=`sed -E '/^ *$/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/(\/Users\/)[^/]+/\1-/g' <<< "$o"` && printf "$Fm" "$1" "$o"; }; Pp () { o=`$PB "$2" | awk -F'= ' \/$3'/{print $2}'`; Pm "$1"; }; Ps () { o=`echo $o`; [[ ! "$o" =~ ^0?$ ]] && printf "$Fs" "$1" "$o"; }; R () { o=; [[ r -eq 0 ]]; }; SP () { system_profiler SP${1}DataType; }; id -G | grep -qw 80; a=$?; A && sudo true; r=$?; t=`date +%s`; clear; { A || echo $'No admin access\n'; A && ! R && echo $'No root access\n'; SP Software | sed -n 's/^ *//;5p;6p;8p'; h=(`SP Hardware | awk '/ Id/{print $3}; /Mem/{print $2}'`); o=$h; Ps "Model"; o=$((h[1]<4?h[1]:0)); Ps "Total RAM (GB)"; o=`SP Memory | sed '1,5d;/[my].*:/d'`; [[ "$o" =~ s:\ [^O]|x([^08]|0[^2]|8[^0]) ]] && printf "$Fr" "$o"; o=`SP Diagnostics | sed '5,6!d'`; [[ "$o" =~ Pass ]] || Pm "POST"; p=`SP Power`; o=`awk '/Cy/{print $NF}' <<< "$p"`; o=$((o>=300?o:0)); Ps "Battery cycles"; o=`sed -n '/Cond.*: [^N]/{s/^.*://p;}' <<< "$p"`; Ps "Battery condition"; for b in FireWire Thunderbolt USB; do o=`SP $b | sed -En '/:$/{s/ *:$//;x;s/\n//;/Apple|SMSC/d;s/\n.*//;/\)/p;};/^ *(V.+ [0N]|Man).+ /{s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;}'`; Pm $b; done; o=`pmset -g therm | sed 's/^.*C/C/'`; [[ "$o" =~ No\ th|pms ]] && o=; Pm "Thermal conditions"; o=`pmset -g sysload | grep -v :`; [[ "$o" =~ =\ [^GO] ]] || o=; Pm "System load advisory"; o=`nvram boot-args | awk '{$1=""; print}'`; Ps "boot-args"; fdesetup status | grep -q On && o=on || o=; Ps "FileVault"; a=(/ ""); A=(System User); for i in 0 1; do o=`cd ${a[$i]}L*/Lo*/Diag* || continue; for f in *.{cr,h,pa,s}*; do [[ -f "$f" ]] || continue; d=$(stat -f%Sc -t%F "$f"); [[ "$f" =~ h$ ]] && grep -lq "^Thread c" "$f" && f="$f *"; echo "$d ${f%%_2*} ${f##*.}"; done | sort | tail`; Pm "${A[$i]} diagnostics"; done; grep -lq '*$' <<< "$o" && printf $'\n\t* Code injection\n'; o=`syslog -F bsd -k Sender kernel -k Message CReq 'caug|GPU |hfs: Ru|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|Roamed|rror|ssert|Thrott|timed? ?o|WARN' -k Message Ane 'SMC:' | tail -n25 | awk '/:/{$4=""; $5=""};1'`; Pm "Kernel messages"; o=`df -m / | awk 'NR==2 {print $4}'`; o=$((o<5120?o:0)); Ps "Free space (MiB)"; o=$(($(vm_stat | awk '/eo/{sub("\\.",""); print $2}')/256)); o=$((o>=1024?o:0)); Ps "Pageouts (MiB)"; s=( `sar -u 1 10 | sed '$!d'` ); [[ s[4] -lt 85 ]] && o=`printf "$Fu" ${s[1]} ${s[3]}` || o=; Ps "Total CPU usage" && { s=(`ps acrx -o comm,ruid,%cpu | sed '2!d'`); n=$((${#s[*]}-1)); c="${s[*]}"; o=${s[$n]}%; Ps "CPU usage by process \"${c% ${s[$((n-1))]}*}\" with UID ${s[$((n-1))]}"; }; s=(`top -R -l1 -n1 -o prt -stats command,uid,prt | sed '$!d'`); n=$((${#s[*]}-1)); s[$n]=${s[$n]%[+-]}; c="${s[*]}"; o=$((s[$n]>=25000?s[$n]:0)); Ps "Mach ports used by process \"${c% ${s[$((n-1))]}*}\" with UID ${s[$((n-1))]}"; o=`kextstat -kl | grep -v com\\.apple | cut -c53- | cut -d\< -f1`; Pm "Loaded extrinsic kernel extensions"; R && o=`sudo launchctl list | awk 'NR>1 && !/0x|com\.(apple|openssh|vix\.cron)|org\.(amav|apac|calendarse|cups|dove|isc|ntp|openld|post[fg]|x)/{print $3}'`; Pm "Extrinsic daemons"; o=`launchctl list | awk 'NR>1 && !/0x|com\.apple|org\.(x|openbsd)|\.[0-9]+$/{print $3}'`; Pm "Extrinsic agents"; o=`for d in {/,}L*/Lau*; do M; done | egrep -v 'com\.apple\.(CSConfig|server)' | while read f; do ID=$($PB\ :Label "$f") || ID="No job label"; printf "$Fb" "$f" "$ID"; done`; Pm "launchd items"; o=`for d in /{S*/,}L*/StartupItems; do M; done`; Pm "Startup items"; sys=`pkgutil --regexp --only-files --files com.apple.pkg.* | sort | uniq | sed 's:^:/:'`; b=`sed -E '/^.+Lib.+\/Contents\/Info.plist$/!d;s/\/Info.plist$//;/Contents\/./d' <<< "$sys"`; l=`egrep '^/usr/lib/.+dylib$' <<< "$sys"`; [[ "$b" && "$l" ]] && { o=`find -L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo}* -type d -name Contents -prune | grep -Fv "$b" | while read d; do test -f "$d/Info.plist" || continue; ID=$($PB\ :CFBundleIdentifier "$_") || ID="No bundle ID"; printf "$Fb" "${d%/Contents}" "$ID"; done`; Pm "Extrinsic loadable bundles"; o=`find /usr/lib -type f -name *.dylib | grep -Fv "$l"`; Pm "Extrinsic shared libraries"; :; } || echo $'\nReceipts missing'; o=`for e in INSERT_LIBRARIES LIBRARY_PATH; do launchctl getenv DYLD_$e; done`; Pm "Inserted dylibs"; o=`find -L {,/u*/lo*}/e*/periodic -type f -mtime -10d`; Pm "Modified periodic scripts"; o=`scutil --proxy | grep Prox`; Pm "Proxies"; o=`scutil --dns | awk '/r\[0\] /{if ($NF !~ /^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./) print $NF; exit}'`; i=`route -n get default | awk '/e:/{print $2}'`; I=`$NS -listnetworkserviceorder | sed -En '/ '$i'\)$/{x;s/^$.+$ //p;q;};x'`; n=`$NS -getdnsservers "$I" | awk '!/^T/{printf "not "; exit}'`; Ps "DNS (${n}from DHCP)"; o=`$NS -getinfo "$I" | awk '/k:/{if ($3 !~ "(255\.){3}0") print}; /v6:/{if ($2 !~ "A") print}'`; Pm "TCP/IP"; R && o=`sudo profiles -P | grep : | wc -l`; Ps "Profiles"; f=auto_master; [[ `md5 -q /etc/$f` =~ ^b166 ]] || Pc $f /etc/$f; for f in fstab sysctl.conf crontab launchd.conf; do Pc $f /etc/$f; done; f=/etc/hosts; Pc "hosts" <(egrep -v "$H" $f ); AT $f; Pc "User launchd" ~/.launchd*; R && Pc "Root crontab" <(sudo crontab -l); Pc "User crontab" <(crontab -l); R && o=`sudo defaults read com.apple.loginwindow LoginHook`; Pm "Login hook"; LD="$(`find /S*/*/F* -type f -name lsregister | head -n1` -dump)"; o=`for ID in $AC; do [[ "$LD" =~ $ID ]] && echo $ID; done`; Pm "Application check"; Pp "Global login items" /L*/P*/loginw* Path; Pp "User login items" L*/P*/*loginit* Name; Pp "Safari extensions" L*/Saf*/*/E*.plist Bundle | sed -E 's/(\..*$|-[1-9])//g'; o=`find ~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $ | wc -l`; Ps "Restricted user files"; cd; o=`find .??* -type d -name *.app -prune`; Pm "Hidden apps"; o=`SP Fonts | egrep 'id: N|te: Y' | wc -l`; Ps "Font problems"; o=`find L*/{Con,Pref}* -type f ! -size 0 -name *.plist | while read f; do plutil -s "$f" >&- || echo $f; done`; Pm "Bad plists"; d=(Desktop L*/Keyc*); n=(20 7); for i in 0 1; do o=`find "${d[$i]}" -type f -maxdepth 1 | wc -l`; o=$((o<=n[$i]?0:o)); Ps "${d[$i]##*/} file count"; done; o=; [[ UID -eq 0 ]] && o=root; Ps "UID"; o=$((`date +%s`-t)); Ps "Elapsed time (s)"; } 2>/dev/null | pbcopy; exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste (command-V). The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Terms of Use of the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

Wifi & Battery Problem since upgrading to ios 8.0.2

me upgraded my iPhone 5s to iOS 8.0.2 but I have a problem about Wifi and Battery !!! my wifi disconnect every 1 minute and when i turn it Off then On it will work for 1 minute and will disconnect again and i have to turn it Off then On again ! And my battery is getting low very faster since upgrading to ios 8.0.2 while i installed just 3 Program (Line-Viber-Clash of Clans) !!! please heeeelp me

Hi there Mehrdad Nofar,
It looks like there may be a few resources for you. For the Wi-Fi issues, I would recommend taking a look at troubleshooting steps in the article below.
iOS: Troubleshooting Wi-Fi networks and connections
As far as the battery concerns, there several things you can do to isolate the cause of the issue. The page below outlines tips to maximize your battey life and isolate any background activities.
Apple - Batteries - Maximizing Performance
Hope that helps,
-Griff W.

Problems with firefox since upgrading to latest software

Since upgrading to the latest Firefox when I go to open my web page details from a usb key my index page appears as a blank page with a background colour, no text pictures, i cannot access any of my other pages. no toolbar including the refresh button, help

I also have a sound issue with fast track pro and posted this on m-audio forum today to see what turns up...
Periodically the sound through my FastTrack Pro crackles then dies.
I think this is more prevalent, albeit I don't understand why, when changing sound 'sources' e.g. if last use was via Ableton and next was from youtube, or visa versa - I can't replicate this at will, it seems to be random.
I can resuscitate things things by going in to the driver settings and changing a setting e.g. the output channel, saving (Applying), then changing back and saving again.
Model: iMac 27" (Mid 2011)
OS: Mountain Lion 10.8 (12A269)
CPU: 3.1 GHz Intel Core i5
Memory: 8Gb 1333 MHz DDR3
M-Audio Products: Fast Track Pro (software 1.8.1, firmware 1.00)
Ableton Live 8.3.3 - 32bit

Wifi constantly crashing since upgrade

OK this is getting unusable ... every 10 maybe 15 minutes at the most i get the spinning wheel and my whole system freezes for 15 / 20 seconds and then it comes back to life but the wifi is hunting.
This has only happened since upgrading tonight.. Tips anyone ?

OK i just managed to watch the log as it happened
02/09/2009 23:24:14 kernel AirPort: Link Down on en1. Reason 4 (Disassociated due to inactivity).
02/09/2009 23:24:14 kernel vmnet: bridge-en1: interface en is going DOWN
02/09/2009 23:24:15 configd[13] network configuration changed.
02/09/2009 23:24:15 vmnet-bridge[164] Examining network configuration.
02/09/2009 23:24:15 vmnet-bridge[164] Intf: en2
02/09/2009 23:24:15 vmnet-bridge[164] Turning off bridge for: en1
02/09/2009 23:24:15 vmnet-bridge[164] Turning on bridge for: en2
02/09/2009 23:24:15 configd[13] setting hostname to "Lee-MBP.local"
02/09/2009 23:24:15 kernel vmnet: VMNetDisconnect called for port 0x133f0b00
02/09/2009 23:24:15 kernel vmnet: bridge-en1: filter detached
02/09/2009 23:24:15 kernel vmnet: bridge-en1: down
02/09/2009 23:24:15 kernel vmnet: bridge-en1: detached
02/09/2009 23:24:15 kernel vmnet: Freeing hub at 0x8d13000.
02/09/2009 23:24:15 kernel vmnet: VNetUserIf_Create: created userIf at 0x133c6e00.
02/09/2009 23:24:15 kernel vmnet: VMNetConnect: returning port 0x133c6e00
02/09/2009 23:24:15 kernel vmnet: Hub 0 does not exist, allocating memory.
02/09/2009 23:24:15 kernel vmnet: Allocated hub 0x8d13000 for hubNum 0.
02/09/2009 23:24:15 kernel vmnet: VMNETSOBINDTOHUB: port: paddr 00:50:56:f1:02:e3
02/09/2009 23:24:15 kernel vmnet: Hub 0
02/09/2009 23:24:15 kernel vmnet: Port 0
02/09/2009 23:24:15 kernel vmnet: bridge-en2: got dev 0x8d98c04
02/09/2009 23:24:15 kernel vmnet: bridge-en2: up
02/09/2009 23:24:15 kernel vmnet: bridge-en2: attached
02/09/2009 23:24:15 kernel vmnet: VNetUserIfFree: freeing userIf at 0x133c6e00.

Why have file sizes in Pages increased since upgrading to latest version?

Hi, I use Pages to compose a monthly newsletter for my yacht club. For that purpose I preferred it to Word because it was so easy to add, resize and position photographs. Before circulating the newsletter to club members, I convert the file to PDF format using the print as PDF option. Last year I was able to put 25 or so photos along with text over 5 pages and finish with a file size of less than 5 MB, which is about as big as I can send without dozens being bounced by members' email filters. Since upgrading my Mac to "Mountain Lion" (and then to "Mavericks") and upgrading Pages, I can't include more than 7 or 8 photos on 2 pages without going over my 5 MB limit. The finished file size seems to be two or three times the combined file sizes of the photos that I include.
Any suggestions for reducing file size? I already use as low a photo resolution as I can.

Peter - thank you so much for this very helpful reply. I had assumed that having "upgraded" I would be condemned to putting up with the Pages 5. I would never have thought of looking in the iWork folder for an older version. Needless to say I can't use Pages 09 to open documents written in pages 5 - but that's no loss. I note that January's newsletter was a hefty 15.5 MB in size, whereas December's, which contains more pages and many more photos was only 2.5 MB.
Thanks again.
Fruhulda - I look forward to reading more of the discussion of the last few months. Being new to the forum it may take me some time to find it.

TS3274 Since upgrade to latest version my screen is very slow to show on the screen . IT IS impossible to put in a password as it seems to time out out

There is a ime delay with everything I type . THIS SINCE upgrade to os7. Can anyone suggest why?

If the above doesn't work, try a reset.
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected.

WiFi not working since upgrading to IOS 7.1.1 on iPhone 4

Can't connect to any WiFi since the IOS upgrade. Ive reset networks, turned airplane mode on/off and powered phone off and on. Nothing works!
Is this a known bug? Any fixes available?

No, it's not a bug. It is most likely an issue with your specific device.
Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new). Try each of these in order until the issue is resolved.
If the issue persists, take the device to Apple for evaluation.

Wifi connection bad since upgrade to 10.4.10

I have been using my MacBook now for a month. Since I had it connected to my network without any problem. A WDS based wifi network with 4 nodes. Since I upgraded the macbook to 10.4.10 the connection gets unreliable.
after some time I notice that Google Notifier shows an exclamation mark. The available SID's are not shown, than just the one shown as being connected to. Turning airport off and on again shows my list anymore. And trust me, there should be at least 5 available SID's in this location of use. The only way to resolve it is by restarting the system. Even once, the system crashed when turning the airport off.
Does anyone have the same problems???
My VAIO SZ2 does connect properly to the wireless network, just like phone and pda (E60 and 770). The network uses is a WPA personal with a preshared key. Based on linksys routers with DD-WRT and OpenWRT.

Me too.
-Macbook/Z0ES
-wrt54gs/dd-wrt
-10.4.10 upgrade
Kernel panics causing "shutdown required.." message.
Two so far today. Panic log shows both from the Atheros (Airport) driver. I'm calling applecare tomorrow..
panic.log:
Mon Jun 25 18:38:51 2007
panic(cpu 0 caller 0x001A4A55): Unresolved kernel trap (CPU 0, Type 14=page fault), registers:
CR0: 0x8001003b, CR2: 0x269aff14, CR3: 0x01eb7000, CR4: 0x000006e0
EAX: 0x00000006, EBX: 0x13931107, ECX: 0x269aff14, EDX: 0x13642a5c
CR2: 0x269aff14, EBP: 0x150f3bf8, ESI: 0x269aff1a, EDI: 0x136422c8
EFL: 0x00010206, EIP: 0x00198d64, CS: 0x00000008, DS: 0x3f9a0010
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x150f39f8 : 0x128d08 (0x3cc0a4 0x150f3a1c 0x131de5 0x0)
0x150f3a38 : 0x1a4a55 (0x3d24b8 0x0 0xe 0x3d1cdc)
0x150f3b48 : 0x19aeb4 (0x150f3b60 0x1 0x1 0x1)
0x150f3bf8 : 0x9a0e1e (0x269aff14 0x13931107 0x6 0x3f9a0900)
0x150f3dd8 : 0x9a3059 (0x136422c8 0x0 0xeda7000 0x0)
0x150f3f08 : 0x39b3c3 (0x13642000 0x3b79080 0x1 0x36e84c4)
0x150f3f58 : 0x39a595 (0x3b79080 0x135eb4 0x0 0x36e84c4)
0x150f3f88 : 0x39a2cb (0x3b788c0 0x0 0x8000 0xf0b)
0x150f3fc8 : 0x19ad2c (0x3b788c0 0x0 0x10 0x0) Backtrace terminated-invalid frame pointer 0x0
Kernel loadable modules in backtrace (with dependencies):
com.apple.driver.AirPort.Atheros(230.8.5)@0x96f000
dependency: com.apple.iokit.IONetworkingFamily(1.5.1)@0x7c4000
dependency: com.apple.iokit.IOPCIFamily(2.2)@0x577000
dependency: com.apple.iokit.IO80211Family(160.2)@0x7da000
Kernel version:
Darwin Kernel Version 8.10.1: Wed May 23 16:33:00 PDT 2007; root:xnu-792.22.5~1/RELEASE_I386
Mon Jun 25 21:19:20 2007
panic(cpu 0 caller 0x001A4A55): Unresolved kernel trap (CPU 0, Type 14=page fault), registers:
CR0: 0x8001003b, CR2: 0xa0000094, CR3: 0x01eb7000, CR4: 0x000006e0
EAX: 0x00000006, EBX: 0x138d0107, ECX: 0xa0000094, EDX: 0x13642a5c
CR2: 0xa0000094, EBP: 0x15133bf8, ESI: 0xa000009a, EDI: 0x136422c8
EFL: 0x00010206, EIP: 0x00198d64, CS: 0x00000008, DS: 0x03c80010
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x151339f8 : 0x128d08 (0x3cc0a4 0x15133a1c 0x131de5 0x0)
0x15133a38 : 0x1a4a55 (0x3d24b8 0x0 0xe 0x3d1cdc)
0x15133b48 : 0x19aeb4 (0x15133b60 0x4b8010 0x15133b88 0x19a319)
0x15133bf8 : 0x9a0e1e (0xa0000094 0x138d0107 0x6 0x3f864e10)
0x15133dd8 : 0x9a3059 (0x136422c8 0x1 0x4b285c 0x4bb070)
0x15133f08 : 0x39b3c3 (0x13642000 0x3b78300 0x1 0x36e8160)
0x15133f58 : 0x39a595 (0x3b78300 0x135eb4 0x0 0x36e8160)
0x15133f88 : 0x39a2cb (0x3b85c80 0x0 0xee6ae98 0x13818b)
0x15133fc8 : 0x19ad2c (0x3b85c80 0x0 0x19e0b5 0x382cd90) Backtrace terminated-invalid frame pointer 0x0
Kernel loadable modules in backtrace (with dependencies):
com.apple.driver.AirPort.Atheros(230.8.5)@0x96f000
dependency: com.apple.iokit.IONetworkingFamily(1.5.1)@0x7c4000
dependency: com.apple.iokit.IOPCIFamily(2.2)@0x577000
dependency: com.apple.iokit.IO80211Family(160.2)@0x7da000
Kernel version:
Darwin Kernel Version 8.10.1: Wed May 23 16:33:00 PDT 2007; root:xnu-792.22.5~1/RELEASE_I386
Macbook Z0ES Mac OS X (10.4.10)

Imac will not connect to Internet via wifi or Ethernet since upgrade.

since the upgrade to Yosemite I am unable to connect to the Internet via wifi or Ethernet. All my other devices ipad/IPhone 6 work fine so issue is not with ISP.
Any help would be greatly appreciated.

I Have tried starting in safe mode and my internet works fine. But I lose all connectivity after reboot into normal mode.

Since upgrade to latest ios, everything is sooooo slow. Why has this happened?

In Japan, using softbank.
Since an upgrade to 7.0.4, everything, and I mena everything, I try to do on the iPad, is sooo slow. It's taken overy 20 minutes to download a 13.2mb app from the iStore.
There is at least one hour a day where the internet simply doesn't connect at all.
And before people chime in with 'this is a carrier issue', it wasn't ever a problem before the upgrade, and has been a consistent problem since the upgrade.

How to Fix a Slow iPad
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-A-Slow-iPad.htm
iPad running slow? How to speed up a slow iPad
http://appletoolbox.com/2012/07/ipad-running-slow-how-to-speed-up-a-slow-ipad/
If You Think iOS 7 Feels Slow Here’s How to Speed It Up
http://osxdaily.com/2013/09/23/ios-7-slow-speed-it-up/
You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
 Cheers, Tom

Why is my battery life worse since upgrading to ios7

After upgrading to IOS7, my iphone 5 battery life is 3-4 hours of standby use, not the expected level. It worked fine for 8 months, then since the upgrade it is pathetic. any ideas why?

http://osxdaily.com/2013/09/19/ios-7-battery-life-fix/

Since upgrading to latest version I cannot open Skype

I upgraded Firefox and ever since, when I turn on the PC I get a message that Skype has encountered a problem and cannot open. The sam happens when I go to the desktop Skype icon. I seem to recall that whenI was upgrading Firefox there was a message about two applications being disabled?? One was a Kodak thing and the other a Windows Net???

Update Java via http://www.java.com/en/<br><br>
See also: http://heartbeat.skype.com/

WiFi Throughput worse since upgrading to latest TimeCapsule

Similar Messages

Maybe you are looking for