WiFi User associating with far AP not with near AP

Hi,
We have two WLC 4402 and around 20 APs model1252G, I have manually distributed between both WLCs.
Problem which I am describing is only associated with single user. User have three APs in its surrounding, AP "One" is placed near by 10 feet, AP "Two" is placed on above floor (with same location) and AP "Three" is placed on below floor (on same location). I am using 1, 2, 6, 11 non-overlapping channels and did not assign same channel on two floor continous.
Problem:
User associating with far AP but not with near AP, due to this user faced low strength. I have increased AP "One" power but it does not worked out.
Need help.
Many thanks in advance.
Regards,
Arsalan

Hi Arsalan,
Thanks for the reply!!
Yes we can configure that!! This feature name depends on the WLC software that you are running..
If ur WLC is running 4.2 WLC code and below.. then thisfeature is called WLAN OVERRIDE , here is the link to do it.. (find for WLAN override 2nd search you will find the feature info and config as well)
http://www.cisco.com/en/US/products/ps6366/products_qanda_item09186a00808b4c61.shtml
if ur WLC is above 4.2 or later, then its called AP-Grouping. here is the link..
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008073c723.shtml
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

Similar Messages

Slow email send/receive for user associated with beehiveonline

It takes hours to send/receive an email to/from the user associated with my beehiveonline workspace. Also, the number of emails that we receive has decreased, it may be not related at all, but there is no way for me to check if that's just due to low customer activity or to timeouts.

Hi,
If you have issues then let us know the date/time of the issue and the degree of delay you are seeeing and we can check if there may be a reason for the delay.
Phil

Where in BAT for "Users Associated with Line" field......

Hi All,
I am trying to find where I can export all user lines via BAT to see if they have an assignment for “Users Associated with Line”.
Basically, I have administered approx 1000 phones (some UDP and some not) however I was unaware that I needed to administer this field for CUPC etc….
I have looked at other posts that explain to update line appearance under the “Users” in BAT however this does no contain the field that I am looking for.
In essence, I need to export all user lines, wash the data for who is not administered for this, then BAT in a change to associate users with line.
Any help much appreciated!

Hi,
I use phones first and than the users option to upload using BAT.
In th phone's tab, edit the the Maximum number of phone lines according to your requirement and click on the Create file format and select Directory Number in the Line field as shown below.
And create your phones with MAC, Description,Phone lines and upload it, make sure it gets uploaded successfully.
Now come to Users tab in the Bat.xlt file, here click on the Number of Controlled Devices as 1 (we are basically making phone as the controlled device to the users, phone already has lines as mentioned in the above step). And fill rest of the other details and upload it.
Note: You can mention the Primary extension and IPCC Extension as part of this operation only.
Hope it helps.
Anand
Please rate helpful posts by clicking on the stars below the right answers !!

Users Associated with Line CUCM9

Our wonderfull HR Staff ran a script that wiped out our IP phone field in AD over the weekend. All of the user accounts got wired out by th e garbage collector before anyone knwe that this has happened . I have afull export from a month ago and was able to get the Owner User ID added to the devices, and the primary and IPCC phone extensions restored. I'm trying to find a way to get the Users Associated with Line filed populated using bulk Admin. I cannot find where to do that. We are running CUCM 9.1
Thanks for any help.

Hi Michael,
You can try the following steps and let me know how it goes.
Create a .txt file format with the following headers, comma separated:
    User ID,Device,Directory Number,Partition
In the lines below the headers, add the corresponding information, comma-separated.
Example, assuming you want to associate user1 to directory number 1001 and user2 to directory number 1002:
        User ID,Device,Directory Number,Partition
        euser1,SEP001122aabbcc,1001,PT-A
        euser2,SEP002211aabbcc,1002,PT-B
You can use Excel to create the file. Save as a .csv file, then rename the file to .txt. Open it to make sure the format matches the one above.
Then got to CallManager Admin Page -> Bulk Administration -> Upload/Download Files, hit "Add new", browse to your file, then select the following targets:
Target: User Line Appearance
Transaction type: Update Line Appearance - Custom File
Verify that the file has been uploaded, then go to Bulk Administration -> Users-> Line Appearance -> Update Line Appearance.
* Under "File name", drop down and select the file you uploaded.
* Do not add any of the checkmarks below, leave empty.
* Click the "Run immediately" radio button.
* Click "Submit"
HTH
Manish

How can I get all users associated with my VSO

I see here: https://www.visualstudio.com/en-us/integrate/api/shared/profiles that I can get my profile info from the API, but can I get all users associated with an account?

Hello!
If you want to see all of that in a single mailbox, you can create a Smart Mailbox from the "file" menu in the top left corner of your screen. It's a bit of trial and error before you get the rules correct, perhaps, but that will work.

ISupport - register a person as a user associated with his/her Person Party

Hi,
iSupport 11.5.10.2
I have a situation in my organisation where I would like to register an individual as an iSupport User associated with his / her Person Party Number.
For example: John Doe has been set up in the system as a Person Party, and has an Account Number generated. He has certain Service Contracts and Install Base records associated with the Account Number. John Doe would like to register through the iSupport portal and be associated with the above Party / Account Number and be able to update his IB, check Orders and Invoices.
Can this be done using any of the existing (seeded) Usertypes, Enrollments etc.?
Thanks and Regards.

This cannot be done in 11.5.10.
But we have this feature in R12.

Users Associated with Line

We will be integrating our UCM 6.1.2 with CUPS 6.x with MOC as the client. On the DN page of the UCM right at the bottom is a button titled 'Associate End Users'. As per the documentation this is required but I still am wondering if this association is really necessary as I will need to update all of our users via BAT csv which will be a lot work provided it can be done via BAT? The users page has an entry under device associations and the primary extension under directory number association has an entry as well so hopefully this will suffice.

Hi
I have User Device Profile and I need to associate Users with Line. I have created file with format
User ID
Device
Directory Number
Partition
ADOUGLAS
UDP_Alexandra_Douglas
22847
PA_POV_OnNet
When I run it I keep on getting the error
user id Error Code Error Description
ADOUGLAS On row 1: bad device name
Result Summary :
Update for 0 Line Appearance passed.
Update for 1 Line Appearance failed.
End Time : 06/29/2010 15:33:20
Thanks

Running BAT to create ADP on users associated with two devices

Problem Details: I have a couple question about behavior of the Bulk Administration Tool that allows you to automatically generate Device Profiles.
1) If a user is associated to a 7941 and a IP Communicator and you run the tool and select to use the personal profile as the logout profile will it set the user as the logout profile for both of the associated devices?
2) Does it port Speed Dials as well as lines?

When you select the logout profile for the user, it will be applied to all the associated devices for that particular user.
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a008087416c.shtml

I would like to change users associated with my imovie project

I'm thinking this is simple but I can't figure out how to do it (I'n new to Macs). I downloaded a movie from my camera and worked on a couple projects before realizing that I was logged in under my sons account. When I log into my account I can't find the movie or the projects. How do I transition the stuff over?

It is simple if you have an external drive. Do you?

Can I change the Apple ID associated with a serial number?

I just purchased an iPad 1 used. The previous owner had its serial number registered under his Apple ID. Does anyone know how to change the apple ID associated with a serial number? On my iPad I am the apple user associated with the device. I am not the associated Apple ID on the Apple website.

Here is the Apple product registration web site.
https://register.apple.com/cgi-bin/WebObjects/GlobaliReg.woa
If you have the receipt for the device, it really doesn't matter to whom the device is registered. The warranty is tied to the device, not the owner of the device so the warranty effectively transfers when you buy the iPad from the previous owner.
Here is the site where you can check to see how long the warranty is still good for.
https://selfsolve.apple.com/agreementWarrantyDynamic.do
Actually, I think all you need is the serial number if you need warranty service and it doesn't matter who owns the iPad at the time that service or warranty issues arise.

Reading a user associated to a particular Lookuptable value in project server 2013

Hello guys,
Please help me out how will i be able to read a user associated with a particular RBS value. and one more thing how can i group the resources and their corresponding RBS value through PSI.
Any sample and suggestion would be appreciated.

Hi
You can use the Resources and Lookup table web services to get these information
few pointes
--Reading all the resources
resourceDS = SResource.ReadResources(string.Empty, false);
            Guid cdval;
            Guid newcdval;
            Boolean fd = false;
--Going though each resource
            foreach (SVCResource.ResourceDataSet.ResourcesRow rsd in resourceDS.Resources)
                SVCResource.ResourceDataSet ResData = SResource.ReadResource(rsd.RES_UID);
                fd = false;
--Checking Custom field value for each resource
                foreach (SVCResource.ResourceDataSet.ResourceCustomFieldsRow rsrow in ResData.ResourceCustomFields)
--Checking the RBS custom field
                    if (rsrow.MD_PROP_UID == <CustomFieldID for RBS>)
--Check the code value(you can read the lookup table and get the code value for each lookup table value)
                        cdval = rsrow.CODE_VALUE;
   --your code for storing the resources to a variable
--Hope this helps
Thanks --Ajith

Login failed for user '(null)'. Reason: Not associated with a trusted SQL Server connection

"[DBNETLIB] Login failed for user '(null)'. Reason: Not associated with a trusted SQL Server connection"
After patches applied on patch Tuesday the database reports the above error.
All accounts are domain accounts and SQLServer uses Windows auth.
DCDIAG show no errors
All servers and DC have been restarted,
Message in db log confirms the connection is being denied due to trust.
Event log shows same rejection
Protocols enabled: named pipes, tcpip, memory
TESTS:
PortQry: "
TCP port 1433 (ms-sql-s service): LISTENING"
Connect with domain admin accounts works from multiple clients systems to DB.
Cannot connect with newly created domain admin account
Can connect if new admin account connect to server in terminal server session and uses UDL wizard or any other tool including isql.
New standard user also fails to connect.
NOTES:
I removed the SSL patch and the IE security update to see if that was an issue.
¯\_(ツ)_/¯

Has someone left the company or has an account of some nature been dropped/replaced?
Please click "Mark As Answer" if my post helped. Tony C.
Hi Tony,
Srry but No. We just installed the monthly updates.
I went back and found I had missed removing a patch. I missed the rollup for Windows Server 2003:
Event Type: Information
Event Source: NtServicePack
Event Category: None
Event ID: 4382
Date:  3/12/2015
Time:  12:26:04 PM
User:  NETTEST\admin
Computer: DATA1
Description:
Windows Server 2003 KB954920 was removed from your computer, and the previous Windows Server 2003 configuration was restored.
After I removed that is still didn't work but after about five minutes it started working.
I guess I ned to report that to MS after I research what might be changed to make the patch work.
Every time I get stuck and ask for help it seems to be just before I stumble on the solution.
Thanks for replying.
Well - maybe this will help someone else.
Thanks again for replying Tony
¯\_(ツ)_/¯

Lync 2013 Error - Certificate could not be published in the database associated with User Services Cluster

Hi Lync gurus,
I have a weird issue:
Just installed a Lync Standard 2013.
Everything works except I keep getting this error in Log: every 30 minute or so.
First an Error: Event 47067
A server did not respond to HTTP request
Server lyncserver.domain.local did not respond to HTTP request PublishCertRequest targeted at
https://lyncserver.domain.local:444/LiveServer/UserPinService.
Cause: Server might be down or the network path between servers might not be properly configured.
Resolution:
Please ensure that the server can be connected on the target port using telnet and then re-try.
Then I get a Warning: Event 47068
GetAndPublish web service failed.
Certificate could not be published in the database associated with User Services Cluster [lyncserver.domain.local ]. Request Details - Entity: [[email protected]], Device Id: [6BB30A3E-2923-553A-8E5F-0B2FB2CEA330], Authenticated User: [sip:[email protected]].
Additional Context: [Publish_Failure: OtherFailure;HttpNoResponse:"lyncserver.domain.local "]
Cause: This could be due to network connectivity issues with the remote server, or because the database is down.
Resolution:
Please ensure that the user services is reachable and the database is up and running.
Thanks for any help

Please check you can telnet port 443 and port 444 on Lync Front End Serve from client.
Try to regenerate a new certificate for Lync Front End Server.
Check all the services on Lync Front End Server are started.
Check the option “Enable all purposes for this certificate” is checked for the trusted root CA certificate.
For the detailed steps:
Run MMC--Add\Remove Snap-ins--certificates--Local Computer--Trusted Root Certificate Authorities--Certificates, find the Root CA certificate you installed--Properties--General, check the "Enable all purposes for this certificate".
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

HT5622 My wife and I shared an Apple ID, have closed out iTunes on her iPhone and iPad but will not allow her email address to be associated with a new account even though it does not appear anywhere in my information. Any suggestions.

My wife and I shared an Apple ID, I have closed out the iTunes on her iPhone and her iPad. While trying to set up a new iTunes account when I enter her email address it says we have to select a new email address. I have checked and her email is not associated with my iTunes account and really do not want to establish another email account. Any suggestions?

Hi Stateler74,
Thanks for using Apple Support Communities. You might be able to find the Apple ID that her email address is associated with by following this article's instructions:
Apple ID: Finding your Apple ID
http://support.apple.com/kb/HT5625
Cheers,
- Ari

Accessing a shared mailbox for users that do not have a mailbox associated with their AD account.

is it possible to give just AD users access to a shared mailbox via webmail in an exchange 2010 environment when those users do not have mailboxes associated with their AD account? They do have full access rights to the shared mailbox.

Hi Shmaxolin,
According to my experience and research, we can use AD account access to shared mailbox, as long as set properly permission.
We can use IMAP application to access it, please try following steps:
1. Make sure you have enabled IMAP and POP3 protocol.
2. Change IMAP4’s authentication to “Plain test logon (Basic authentication). No…..”(open EMC--->Server Configuration--->Client Access, switch to POP3 and IMAP4, right-click IMAP4 and select Properties, then switch to Authentication)
3. Use the following user format DomainName\Username\MailboxAlias (e.g. DOMAIN\John.Doe\Shared.Mailbox1) to log into the shared mailbox.
More details about Access shared/delegate mailbox of Exchange Server, please refer to:
http://www.limilabs.com/blog/access-shared-delegate-mailbox-exchange-server
Best Regards,
Allen Wang

WiFi User associating with far AP not with near AP

Similar Messages

Maybe you are looking for