Wild Card Cert

Is there a way to use a wild card cert in the CSS SSL Proxy list ?
Looks like you can request a cert such as ABC*.xyz.com from Verisighn.
Can you use that in a CSS for URLS like
ABC1.xyz.com
ABC2.xyz.com
ABC3.xyz.com
and only use one VIP ?
Thanks
Steve

the domain will be used to get a destination ip address.
So, the CSS does not really control the domain<->ip resolution.
If you can configure your DNS server to point all domains to 1 ip, then you only need 1 vip on the CSS.
However, if you have 1 ip for each domain, you will need the 1 vip per domain on the CSS.
I know working with a single vip sounds easier, but this could be a big limitation for you in the future.
If your number of domain increases or if the traffic load increases, the CSS performance could slow down as it will require to inspect all data to identify the domain name.
Playing with more vip will allow you to identify the domain with just the ip and increase performance.
Regards,
Gilles.
Thanks for rating this answer.

Similar Messages

HTTPS hostname wrong - wild card?

I have a simple https client that produced the following error message -
" java.io.IOException: HTTPS hostname wrong: should be <test.cat.com>, but cert says <*.cat.com> "
I thought that the * is the wild card,thus test.cat.com should be accepted. Any ideas?
Thanks, Jack

ok I did exactly that and it's good. However I suggest that you don't return true automatically since it bypass completely the protection. You can easily implement the check for the domain name (which is the current implementation in jsse) and then add the wildcard special cases.
Have fun
Francois

Using wild card with Captivate 5 ( fill in the blank)

I am training software package that requires many fill in the blanks besides the login screeen. If I were to recording the actions using Captivate 5 record, I think, I can only use a demonstration recording as oppsed to having my students interact with the product by filling in the blank. For example, my product asks for a login. When I login to demonstrate how it should be done, the product reponds correctly. By my student is limited to watching as opposed to interacting. While login is not such a big deal, there are several other areas where the same concept applies. Ideally, I wish to use wild cards in fill in the blank so that any name or information can be used to interact with Captivate and move the slide along. Is this possible, and if so, how?

I think Lilybiri may be misinterpreting your use of the term "wildcards" to mean using them in the programming sense.
Perhaps you are referring to the characters that appear in a typical Password field to hide what the user is actually typing?
If so, the text field object in Captivate has an option to use these password characters so that the user's typing characters are hidden. The characters used are asterisks, which are what some people refer to as wildcard characters.

File adapter wild card not working

Hi Gurus,
My file adapter seems to have issues with me
This adapter do not obey me when I specify wild cards. I have tried * , ? and also "Adavnced selection of source file" but no use. Although, he is a perfect gentleman when I specify complete file names.
Could you please suggest how to tame him?
Regards,
AV.

Hi,
this is what SAP Help says about it:
file.sourceFileName=<filename>
Specify the name of the file that you want to process.
The name can contain a placeholder (*) at any point, so as to be able to select a list of files for processing.
The following are valid examples for filename:
myFile.txt
my*.txt
*.txt
File.
File.*
myle.
Names that comprise more than two parts are also permitted.
Hope it helps.
Regards
Patrick

Wild Card as key field value in Content Conversion

Hi,
Can any one please tell me that can a wild card such as '*' be used as key field value.
Thnx,
Pravesh Puria.

Hi Pravesh
For the file name in the sender file adapter you can use the '*' or '?'(as a placeholder for exactly one character)
You can also enable the "Advanced Selection for Source File" in the sender file adapter, where you can do two things:
a)you can specify an exclusion mask for the file name specified above.
b)you can specify/lits multiple directories with a file name and an associated exclusion mask, e.g. in file name you put ".txt" and in the associated exclusion mask "a". The every file with ".txt" except "a" will be fetched from that directory.
Try it out.
Regards,
Goekhan

Characteristic wild card in report painter

Dear experts..
I am developing a report painter for PS cost element report with structure CCSS.
I want to create rows with dynamic characteristic and I am thinking of using wildcard in the characteristic variable.
What I am trying to achieve is basically to filter WBS only for those which consist "ABC" in the project number (ABC in POSID). I know it can be achieved in the selection screen but I want the selection screen to be as generic as possible and only filter it at row level.
In the normal functional report we can use '*' as the wildcard but it can not be used in characteristic variable.
Appreciate any enlightenment on how to use variable or set to be able to do this.
Thanks in advance

Hi Alexei,
Welcome to SDN.
You need to give the exact file name. System can not determine file name with wild card.
Hope this will help.
Regards,
Ferry Lianto

How to use wild card character in input field

Hi
I'm creating model in which the Purchase Order information need to be entered in Input Field.
My requirement is search using wild char char as '*'
Let say in input field i gave PO order as 20* then it'll search for all the PO's which starts from 20.
Could you please share some documents/guidelines, for this issue
Thanks and Regards
Puneet

Hi,
You can use the wild card char in the input box.please try below steps.
1.Check whether the input string has ' * ' char using "CONTAINS(text,pattern)" operation.
2.If yes, Replace the ' * ' with space by "REPLACE(text,pattern,repstr)" operation.->consider this result as input2
3.Now , Have a Filter from ur webservice(which gives your Purchase Order information )
and filter it by the condition " BEGINS(WSField,input2)"
the Final expression in the filter will be "_=IF(CONTAINS(input,""),BEGINS(HelpWSField,REPLACE(input,"\","")),true)_"
Hope it helps.
Regards,
Priya
Edited by: priya on May 20, 2009 12:49 PM

When using rabbitmq-jms for vFabric RabbitMQ javax.jms.Message.getJMSDestination does not return the actual destination when it is received from a consumer listening on a Topic with a wild card

When using rabbitmq-jms for vFabric RabbitMQ javax.jms.Message.getJMSDestination does not return the actual destination when it is received from a consumer listening on a Topic with a wild card. I have tested with both 1.0.3 and 1.0.5 clients with RabbitMQ 3.1.5.
I was wondering if the community was aware of this problem and if there are any workarounds? If not what is the proper channel to file a bug report. An example code snippet is below. The test fails because the TextMessageMatcher expects the destination passed in on construction (second parameter) to equal the desination on the message received (aquired from getJMSDestination).
        Mockery context = new Mockery();
        final MessageListener messageListener = context.mock(MessageListener.class);
        final Latch latch = new LatchImpl();
        final String prefix = "test" + System.currentTimeMillis();
        context.checking(new Expectations() {
                oneOf(messageListener).onMessage(with(new TextMessageMatcher("MSG1", prefix + ".1234")));
                will(new CustomAction("release latch") {
                    @Override
                    public Object invoke(Invocation invocation) throws Throwable {
                        latch.unlatch();
                        return null;
        final Connection connection = createConnection(null, null);
        Session session = connection.createSession(false, Session.AUTO_ACKNOWLEDGE);
        connection.start();
        Topic wildcardTopic = (Topic) getInitialContext().lookup(prefix + "." + "#");
        Topic destination = (Topic) getInitialContext().lookup(prefix + ".1234");
        final MessageConsumer consumer = session.createConsumer(wildcardTopic);
        consumer.setMessageListener(messageListener);
        MessageProducer producer = session.createProducer(null);
        producer.send(destination, session.createTextMessage("MSG1"));
        latch.await(5000);
        connection.close();
        Thread.sleep(5);
        context.assertIsSatisfied();

Check where your MDB sends the [response] messages to.

Wild card search in existsNode function

Hi,
How can i do a wild card search for the below data?
I have a table as follows:
ID VARCHAR2(32 BYTE),
MESSAGE_TYPE VARCHAR2(64 BYTE),
MESSAGE_CONTENT XMLTYPE,
REJECTED_REASON VARCHAR2(256 BYTE)
And Sample XML as:
<?xml version="1.0" encoding="US-ASCII"?>
<MessageEnvelope>
<Header>
<Partner>Renault</Partner>
<MessageType>Release</MessageType>
<PartnerMessageType>S74</PartnerMessageType>
<MessageTime>2001-12-17T09:30:47.0Z</MessageTime>
<LinkToRawMessage>String</LinkToRawMessage>
</Header>
<Body>
<Release>
<Addresses>
<DealerDestAddr>ABCD</DealerDestAddr>
<DestAddr>ABCD</DestAddr>
<NextDestAddr/>
<StartAddr/>
</Addresses>
<Assignment/>
<ClientStatus/>
<Dates/>
<HoldInfo>
<HoldCode>HoldTest</HoldCode>
</HoldInfo>
<Message/>
<Partner>
<OrderGiverCode>CMR00BCV</OrderGiverCode>
</Partner>
<ToDo/>
<Transport/>
<Vehicle>
<VIN>W0LGDM9A_Ran11115</VIN>
</Vehicle>
</Release>
</Body>
</MessageEnvelope>
I am executing the foll query:
select * from t_xml x where x.message_type='DBLVEH' and x.MESSAGE_CONTENT.existsNode('//*[*="Release"]')=1;
This gives me correct result.
But i need to search *Rel and it should give me the desired result. How can i accomplish that?
I tried the foll and it did not work:
select * from t_xml x where x.message_type='DBLVEH' and x.MESSAGE_CONTENT.existsNode('//*[contains(*,"Re")]')=1;
Regards,
Sprightee

sprightee wrote:
Hi,
How can i do a wild card search for the below data?I am not sure how this can be achieved using existsNode function but does following work for you?
SELECT *
FROM t_xml
WHERE
    XMLExists(
      'declare namespace ora = "http://xmlns.oracle.com/xdb"; (: :)
       $d//*
         [ora:matches(text(), "Re*")]'
      PASSING MESSAGE_CONTENT AS "d");

Wild card search in a FM

Hi experts,
I have a FM in which there is one table customer_name
It has fields as SIGN (type SIGN), OPTION (type OPTION), LOW (type name1_gp), HIGH (type name1_gp).
Now the user can give single value, or a range of values for the customer name.
I am familiar with the wild card search for a select option, but not sure how to apply that funda here.
For ex: If a customer enters the customer name as MG*, then all the names starting with MG should appear
in the output.
Similarly, if the user enters AP* in LOW and MG* in high, the corresponding output should be displayed.
Can you please help me out?
Thanks,
Ajay.

Hi,
Do like this
t_table-sign = 'I'.
t_table-option = 'CP'.
t_table-low = 'AB*'.
t_table-high = 'MG*'.
append t_table.
Use this in your select query.

Wild card usage in standard F4 help - issue

Hi Friends,
i want to list a function module which - second character should be 'Z' .........HOW TO DO THAT ...
usually we will put : in se37 - IN THE FIELD VALUE COLUMN : %z*
but wild card % or ? is not accepting ....give me your help on this.
regards
raaj

thanks for your response.
if we use z* or *z.....
please not that only second character of my listing should be "z"
If you give *z - it will list out all values which ends with "Z" ....
HOW TO USE THE WILD CARD : %

Alert Rule - not working. Wild Card character issue

Hi All,
I have a requirement where I need to trigger alerts for mapping failures
of all the interfaces whose namespace is urn:abc.com:odna* or urn:abc.com.odna*. (in the first instance, there is dot before odna and int he second instance, a colon before odna )
So to suit both the cases, I gave urn:abc.comodna in the Alert Rule.
It worked before. But now its not working.
Then when i changed it to urn:abc.com:odna* it works again. i really dont understand how it worked before and why it fails now.
What is the reason for the unpredicatable behaviour of WildCard Character based Alert Rules?
Should Wild Card Characters be avoided completely?

Hey
Just create two separate alert rules for the same alert category
one for urn:abc.com:odna* and another for urn:abc.com.odna*.
but before that please make sure that "Suppress multiple alerts of this rule" box is unchecked.
Also please check SAP Note 913858
Thanx
Aamir
Edited by: Aamir Suhail on May 20, 2009 9:16 AM

How to use wild card with variable in powershell

HI
i am trying to use wild card with variable but getting an error message, "You cannot call a method on a null-valued expression."
$src = 'C:\Temp'
$TabletzipPath = $src + "tab*.zip"
i would like to copy the tablet zip file which is placed in in $src to be copied in $TabletzipPath.
i am using tab* because this file name changes continuously. so if i give a fix name for example tablet1.zip than it works fine.

Not sure if the wildcard will work without seeing how you're using the variable.
That said, I can say that it looks like you're missing the backslash between the $src path and the wildcard filename. As-is the above code assigns a value to $TabletzipPath of "C:\temptab*.zip" instead of what you are likely expecting ("C:\temp\tab*.zip")
Jason Warren
@jaspnwarren
jasonwarren.ca
habaneroconsulting.com/Insights

Case Sensitive problem in Select Option for wild card search

Hi,
Can anyone please let me know how to make the wild card search in any select-option non case-sensitive. What I mean by this is for eg. we want to find out all the POs with short text containing the word 'process', what we do we populate a range with OPTION = 'CP' and LOW = 'process' and select EKPO with short text in this range. This select is however case-sensitive and POs with short text containing 'Process' is not retrieved. But my requirement is that this should be non case-sensitive and both the POs should be in the result set.

Hi,
Hope this helps you
CS:
You can select characters in operand2 for a direct comparison by adding the escape symbol "#" before the required characters. For these characters, upper/lower case is taken into account, wildcard characters and the escape symbol itself do not receive special treatment, and trailing blanks in operands of type c are not cut off.
Covers Pattern: True, if the content of operand1 fits the pattern in operand2. Wildcard characters can be used for forming the operand pattern, where "" represents any character string, and "+" represents any character. Upper/lower case is not taken into account. If the comparison is true, sy-fdpos contains the offset of operand2 in operand1, whereby leading wildcard characters "" in operand2 are ignored if operand2 also contains other characters. If the comparison is false, sy-fdpos contains the length of operand1.
Regards
Krishna

How to prevent the use of wild cards in select-option

Hello experts,
Is it possible to prevent the use of wild cards in a select-option? If yes, how is it done please?
I have a
SELECT-OPTIONS: o_comp FOR dbtab-field OBLIGATORY DEFAULT 'FI'.
and, I want to prevent the users for giving in some thing like FI* with the wildcard bc it would lead to dump.
I want an error message to display and prevent the users for making such entry.
Please I need your help and I would be very grateful.
Thanks
Nadin

You have to use SELECT_OPTIONS_RESTRICT to restrict input allowed. Call this FM in INITIALIZATION or SELECTION-SCREEN OUPUT sections.
Sample :
TYPE-POOLS: sscr.
INITIALIZATION.
* Restrict SELECT-OPTIONS
PERFORM restrict_select.
FORM restrict_select.
DATA: restrict TYPE sscr_restrict,
        opt_list TYPE sscr_opt_list,
        *** TYPE sscr_***.
* Défine select-options modes (aka option list)
* - ALL standard - all options allowed
CLEAR opt_list.
MOVE 'ALL' TO opt_list-name.
MOVE 'X' TO: opt_list-options-bt,
               opt_list-options-cp,
               opt_list-options-eq,
               opt_list-options-ge,
               opt_list-options-gt,
               opt_list-options-le,
               opt_list-options-lt,
               opt_list-options-nb,
               opt_list-options-ne,
               opt_list-options-np.
APPEND opt_list TO restrict-opt_list_tab.
* - EQU only equality allowed (list of values)
CLEAR opt_list.
MOVE 'EQU' TO opt_list-name.
MOVE 'X' TO opt_list-options-eq.
APPEND opt_list TO restrict-opt_list_tab.
* Affect modes to parameters or block of parameters
* ALL by default
CLEAR ***.
MOVE: 'A'          TO ***-kind,
        '*'          TO ***-sg_main,
        'ALL'        TO ***-op_main.
APPEND *** TO restrict-***_tab.
* EQU to internal material number
CLEAR ***.
MOVE: 'S'          TO ***-kind,
        'S-MATNR'    TO ***-name,
        'I'          TO ***-sg_main, " no exclusion
        'EQU'        TO ***-op_main. " only value list
APPEND *** TO restrict-***_tab.
* Call FM
CALL FUNCTION 'SELECT_OPTIONS_RESTRICT'
       EXPORTING
            restriction = restrict
       EXCEPTIONS
            OTHERS      = 1.
ENDFORM.                    " restrict_select
In the sample, only select-options for matnr is restricted to single value list.
For your request build a mode with all options except "pattern" ones : CP and NP.
Regards

Wild Card Cert

Similar Messages

Maybe you are looking for