Will a CanoScan LIDE 210 scanner work with OSX 10.11 beta?

I am testing OSX 10.11 Beta release and happen to need a scanner.  I am asking to find out if the CanoScan Lide 210 will work with this version of OSX?

Any luck? I upgraded to OSX 10.11 and sometimes it works sometimes it doesnt.

Similar Messages

  • Will an epson photo 2400 scanner work with OSX 10.7?

    Will an epson photo 2400 scanner work with OSX 10.7?
    If so where do I get the drivers/software to run it?
    I have used it with aquire, but only in flat bed scanning.
    I am not able to use the film/slide mode anymore because the software that came with it is for 32 bit macine code.
    Any ideas?

    I realize this isn't a direct answer to your question, but I have an Epson Perfection 1670 flatbed scanner.  I plugged it into a USB port after installing Lion, and it works fine with both the Image Capture and Preview applications.  ("FIne", for me - I don't have a need for slide/transparancy scanning.  Image Capture recognizes the scanner can do it, giving two modes for transparancy scanning, but in a quick and dirty test a minute ago it didn't seem to work.  Since I don't need the capability, I'm not going to struggle with it to see what I've done wrong.)
    Good luck
    srb

  • Will an HP Mini 210-1212NR work with a HP Mini 110-1212NR? Screen?

    I accidently purchased an HP mini 110 screen for hp 210 netbook. I'm wondering if it will still work if I install it? Will i need to install drivers...first?

    Hello Fiona6,
    I use iMac (Snow Lep) and 2011 Mini (Lion) and from both systems my results are:
    Wired keyboard & mouse - work ok, I don't like or use wireless types.
    My LaserJet 1010 - works ok (Your 1012 should also work, same series of printer).
    If your display works ok now, cannot see why it would not work. My mini works with various vga and DVI displays I have at various times attached to it.
    Don't know about your scanner though, with my all in one printer/scanner I have had to use OS X Image Capture program to scan. Might be worth a look at Epson's site to check on any software updates.
    Roy.
    Edit: Regarding display if you are getting a new mini you will need a new display adapter, minidisplayport to vga or dvi, assuming your display is one of these. This can be plugged into the Thunderbolt port on the new Macs.
    Message was edited by: royfromchatteris

  • Getting Canon CanoScan Lide 20 to work with 10.4.10 and 10.4.11

    When I upgraded to the latest version of Tiger 10.4.10 and .11 ... My Canon Lide 20 which had been working perfectly for years just stopped working. I tried to download the latest driver from canon but kept getting errors. After several different attempts I found this posting on version tracker did what it said and it worked!
    "Problems Installing CanonScan Software - Version: 4.1.3, 2/5/2007 06:30AM PST
    (3 of 3 users found this comment useful)
    robert.loney
    For Macintosh OSX users (including intel Macintosh computers) who have problems installing Canon scanner software, including older models. Please try the following steps to successfully install your scanner driver software:
    Short Fix:
    1. Use the "Deldrv" program to remove previously unsuccessfully installed driver(s). The "Deldrv" uninstaller can be found on the Canon website at the bottom of the Canon scanner driver pop up window that you access to get the drivers for your scanner.
    2. Use the "Find?" under the File menu (command-F) or use Spotlight (command spacebar) to find the folder "CFMSupport". Select this folder (don't open it), and use the 'Get info' command in the File menu (command-I) to open information about the Ownership and Permissions of the folder. Click on the arrow beside 'Ownership and Permissions' so it points downwards, then click on the arrow beside 'Details' so you can see the details. Click on the padlock icon so it is unlocked. Then set owner to your user name, set the Group to admin, and set access for all users to Read & Write.
    3. Reinstall the CanoScan Toolbox first, then the scanner drivers from the Canon website or your CD, restart your computer."
    Uninstalling I think made all the difference. I hadn't done that before. Thanks to Robert Loney for this. I was about to purchase VueScan which also worked... but he saved me $49 buckswhich is more than I paid for the Lide 20 5 years ago.
    I also lost my external hard drivers when I upgraded to 10.4.10. never fixed that problem... just went and returned my Western digital Mybooks (both premium and pro additions) (I had been dealing with customer service and returning the ones they kept shipping me for months). I got a Maxtor 750 GB one from Circuit city and it has worked like a charm! I wonder if there was something I needed to uninstall to get that to work as well.
    I hope this is helpful to everyone else out there.

    To add to Ryan's posting, anyone in the UK/Europe may need to access the Canon US website (http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=DownloadDet ailTabAct&fcategoryid=351&modelid=6624) to obtain the latest version of the scangear driver 7.0.1.1X and Canoscan software 4.1.3.0. Judging by their file dates these versions appear to have been released in 2007. The Canon Europe site has the older version 7.0.1.0 of the driver.
    The tips should may also apply to the LIDE 30 and N670 and other scanners which appear to use the same software.
    On my system the permissions on the CFMsupport folder allowed update of the software without changes so you may also find that updating the drivers to these versions is sufficient, and you don't need to bother with the permissions changes.
    I have experienced problems with the scan gear software not setting the folder to receive the images correctly. At one point in the scan process - after clicking the scan button - it offered an open file dialogue box rather than a choose folder dialogue. I found that if selected any file in the folder and clicked open the problem seemed to go away.

  • Which home scanner works with windows 8. I have a N676U Cano Scan that will not with 8. Walt.

    Which home scanner works with windows 8? I have a N676U Cano Scan that will not with Windows 8. Is there a fix for this? Thanks: Walt.

    Hello Walt.
    Unfortunately, the CanoScan N676U is not compatible with Windows 8.
    For more information, please call us at 1-800-OKCANON.
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • Will my printer and scanner work with the new intel mac?

    My first post.. so I hope i am in the right place! (was in wrong place last attempt!)
    I want to buy the new intel...but I would like to know for sure if it will work with my scanner and printer.
    Printer is Epson Stylus Photo 2100 and the scanner is Microtek ScanMaker 4900.
    I have emailed both Epson and Microtek... phoned Epson.. and I still do not know the answer.
    The responses were
    "At this point in time with have been given no information on whether our printer drivers will work or not....".
    "Yes it will work with OSX 10.4"
    "As you know this new intel chip has just hit the market. This particular configuration is in the alpha stage of testing. As of now there has not been any reports or customer correspondence of any concerns."
    I have been scanning these posts and it seems that only the operating system is relevant? If anyone could help I would appreciate it. I am finally able to replace my old, old, well loved G4 but am worried I will make the wrong decision.

    Thanks all for the helpful comments. I am getting closer to going out and buying the intel. As for the Canon printer... its not really an option for me, since the Epson cost me more than the computer will! But I will keep it in mind for the future. And do you think this applies to digital cameras as well Tomzo? I have been considering buying my first digital.. and thought the pentax might be best, since it apparently can use the lenses from my film camera.
    Thanks again all..I will keep checking the apple site list and the web sites as suggested by you.
    Power Mac G4 (AGP graphics)   Mac OS X (10.4.4)  

  • Re: Trouble with peripherals (CanoScan LIDE 30 Scanner & HP LaserJet 1020)

    The Canon CanoScan LIDE 30 scanner didn't have any autodetection, so I want to the Canon Web site to look for drivers. I grabbed the drivers, packaged in a .dmg file, from Canon. Running the setup file, I was a bit perplexed what it wanted me to do, so I installed the drivers in the Applications directory and rebooted the system when prompted.
    That did nothing - I still couldn't access the scanner. I tried a couple other places - root of the hard drive, /Library/Image Capture... nothing.
    I'm at a complete loss here, and couldn't figure out how to do it.
    And the printer.
    I hooked up the HP LaserJet 1020 to the Mac. Nothing happened, so I went into the Print & Fax System Utility to set it up. The printer browser was able to detect it, but there was no listing for the HP LaserJet 101 in the driver selections. Hewlett Packard doesn't offer Mac drivers for the printer.
    Anything I can do to get these two peripherals working?
    Feel free to CC responses to [email protected]

    The Canon CanoScan LIDE 30 scanner usually installs a file "N124u-buttonmanager" in your Login items (actually the standard install used to put the "buttonmanager" for both the LiDE 20 and LiDE 30 scanners, see this User Tip: kmosx2: Looking for devices matching vendor..).
    Their more recent software is better behaved: I have an all in one, and there are no Login items, everything is installed in a "Canon Utilities" folder inside "/Applications".
    So, if the software you downloaded includes a "buttonmanager", make sure you choose the right one (see the User Tip) and put it in your login items (System Preferences > Accounts).

  • CanoScan Lide 210 Help

    Hi,
    Just purchased the 210 to go with my new iMac 10.9 OS and are having problems. I don't have a CD drive. 
    I downloaded from the Canon website the following,
    ICA Driver Ver.3.1.0
    LIDE 210 Scanner Driver Ver. 17.7.1a
    Software : MP Navigator / Quick Menu / Solution Menu
    Documents scan okay but nothing happens - can't print / e-mail / PDF etc.
    I've obviosly mucked something up and not being tech savvy I would appreciate someone pointing me in the right direction.

    Thank you, Paul, for looking into my issue. The canon support person did have me to install the latest ICA driver from their site and it didn't help the problem. I really like the canoscan lide 210, even using it in mp navigator. I would love to be able to use it from image capture & preview and print & scan...without having to either restart the computer or unplug the usb cable, or as I mentioned, using the scanner in navigator first, and then switching over to the other applications, it works fine. For me, the issue is the scanner is D.O.A. after coming out of sleep. I removed the twain driver to see if the image capture would work on the ICA driver. No good. I truly believe that this scanner will just not "wake from sleep" in the aforementioned applications. I asked another Canon tech guy if I got a "powered" scanner would it work after sleep on my iMAC lion 10.7.3. He just didn't know. My hp printer works fine, after sleep, from its usb port, using the hp driver. My scanner works fine, after sleep, using the mp navigator driver, on the usb port. My problem is the ica driver won't work on the usb port for my scanner, after sleep.
    Thank you again, for looking into this issue. Hopefully, you will have a good suggestion, even if it means purchasing an epson scanner, which is AC powered.
    Ronnie

  • Canon LiDE 210 insufficient memory with Lion

    My LiDE 210 scanner which has worked in the past using OSX10.7 but it now says "insufficient memory" each time I launch MP Navigator EX 4.0.
    Canon advised me to open MP Navigator and select 'View and Use', where it says 'Specify the scanned location', select a different scanner location to see if this resolves the issue. I am unable to do this as I get the "insufficient memory" message immediately I double click on the Canon software. If this did not resolve the issue, they recommended uninstalling and re-installing the latest drivers, which I have done but with no solution to the problem. I haved repaired permissions, checked printers in the library and there does not seem to be anything missing or conflicting. I cannot find any reference to TWAIN in the Library and finally the basic scanner functions are available using Image Capture.
    Any ideas most welcome. Thanks

    The scanner driver file is installed in HD > Library > Image Capture > TWAIN Data Sources. Here you will see the LiDE210.ds file. This package file contains information used by the scanner and removing the scanner entry in Print & Scan does not remove this file. You could trash this file (make sure you remove the entry from Print & Scan first) and then run the v17.7.1 scanner driver installer again.
    If MP Navigator still fails it could actually be this application rather than the scanner driver at fault. Note that Image Capture uses a different driver called an ICA. So to test that the TWAIN scanner driver is okay you would need a TWAIN compatible application. And one such application is VueScan. Install this and see if you can scan without any error. If you can then it indicates the issue is with MP Navigator. If VueScan also fails then you do have a scanner driver issue.

  • Upgraded to OS X 10.9 and now cannot connect to Canoscan LIDE 90 Scanner. Cant find a new driver anywhere. Any ideas??

    I have upgraded to OS X 10.9 and now I cannot connect to my Canoscan LIDE 90 Scanner. Cant find a new driver anywhere. Any ideas??

    Like Dan White, I have found that I can still run the Lide 90 under Mavericks. As Dan says, the buttons on the front of the scanner don't work but I rarely if ever used them.
    I have just tested the scanner using Acrobat Pro and it loads up the Scangear software to capture the scan, with no problems at all. I didn't have to reinstall anything as it was all there already and working in Mountain Lion. Photoshop CS 5.1 is different; it does not recognise the scanner, presumably because it can't find a TWAIN driver for it. Image Capture does not recognise the scanner either, but I don't have the latest (10.8) Canon MP Explorer and Explorer Opener software installed.

  • CanoScan LiDE 700F Scanner not opening up

    Whenever I try to scan anything with CanoScan LiDE 700F scanner my computer gives the message "scanner reported an error. An error ocurred while communicating with the scanner." I have to unplug and plug back the USB port and only hten it opens up.  When I try to open the scanner with System Preferences, scanner opens up, but as soon as I hit "scan" the same error message pops up.  I uploaded the latest driver from Canon website, but the problem persists.  I also deleted and re-installed the sanner in system preferences, but it didn't help.
    It used to work fine when I initially installed it (on Leopard), but then suddenly this problem arose.

    This same error message was first noticed on 10.6. It would only occur after waking the Mac from sleep. Prior to the sleep state you could scan using Image Capture without error. But if the Mac entered a sleep state with the scanner connected, after waking it and then trying to scan, the error message would appear. And as you have found, the quick solution is to unplug the USB cable and then reconnect it.
    This problem only occurs with Canon scanners that use USB power. The models that have their own power supply, or the All In One devices with scanner, do not suffer the same fate. Apple Engineering is aware of this and have told me that it is up to Canon to fix.
    Note that the same problem does not occur when using Canon's MP Navigator application. This application uses the full TWAIN-based scanner driver, whereas Image Capture and Preview use the ICA driver, and works fine after waking the Mac from a sleep state.

  • CanoScan LiDE 60 scanner driver problems

    I'm usually pretty good at troubleshooting software issues on my iMac, but this scanner problem has me absolutely stumped!!! My old Canon CanoScan LiDE 60 scanner stopped working the other day...out of the blue. I have been using the ScanGear software without a hitch, and now every time I open the program, I get a "Failed To Open Driver" message. I figured out that I obviously needed to upgrade my software and drivers. I did some research online and was told I needed to install the new CanoScan software and driver from the Canon website. This scanner model is technically not supported by Snow Leopard, but some people got it to work!! Well...I tried that, followed all instructions correctly, then restarted my Imac and replugged my scanner USB cord. I opened the ScanGear software again, but I still have the missing driver message!! I've been trying several little tricks to get it work, but still nothing. I'm at the point where I need to start from scratch and uninstall everything related to the scanner, but I'm not sure how to do that correctly either, removing all the orphaned data! Can someone please give me a step-by-step process what I need to do?

    Guys, thanks for this. I've had similar problems but with your help and others solved both issues for the Toolbox and Driver (OS X10.6.8):
    Make sure all previous drivers downloads etc are deleted, inc the DMG files etc and disconnect the scanner.
    You can then download the latest Toolbox from the UK site [dated Feb 2011] (it doesn't require you to reboot, for some strange reason??). Then download the latest driver from the Australian site. You have to reboot then.
    Everything seems to work fine. No preview as before unfrotunately but goes a treat. Hope that helps guys.

  • Will the HP LaserJet Pro P1102w Printer work with OSX 10.9.5?

    I am looking for an affordable LaserJet printer for home. I want to know if the HP LaserJet Pro P1102w will work with OSX 10.9.5. Their website only goes up to OSX 10.7 for compatible OSX systems.

    OS X- Printer and scanner software available for download

  • Will Office Web Apps Server 2013 work with SharePoint 2013 sites hosted in SP2010 compatibility mode?

    We are planning a upgrade of a SP2010 farm to 2013. There has been a bit of customization so we wish to run the old sites on the new SP2013 platform in SP2010 compatibility mode.
    So my question is will Office Web Apps Server 2013 work with the old sites hosted in compatibility mode?
    I found a similar query from March 2014 found here 
    http://sharepoint.stackexchange.com/questions/93101/office-web-apps-2010-running-on-sharepoint-2013-for-compatibility-mode-sites/116281#116281 
    Has there been an update released to resolve this
    Cheers D

    Hi  ,
    According to your description, my understanding is that you need to know whether Office Web Apps 2013 is working with SharePoint 2013 sites which is in SharePoint 2010 compatibility mode.
    For my test, Office Web Apps 2013 with SharePoint 2013 sites which is in SharePoint 2010 compatibility mode is working fine.
    Thanks,
    Eric
    Forum Support
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
    [email protected]
    Eric Tao
    TechNet Community Support

  • My iPad Mini with retina display suddenly will not connect to the Internet. It shows full wifi bars, yet no web pages will load. My Internet is working with all other apple devices in my house. The iPad also no longer works with celluar data.

    My iPad Mini with retina display suddenly will not connect to the Internet. It shows full wifi bars, yet no web pages will load. My Internet is working with all other apple devices in my house. The iPad also no longer works with celluar data. I'm not sure what has happened. It was working fine a few hours ago. I have tried resetting it, ive restarted my browser etc. I tried to erase all data from my Ipad but I can't do that because it needs to sign into my Apple ID and use the Internet!

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are drooping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    Fix WiFi Issue for iOS 7
    http://ipadnerds.com/fix-wifi-issue-ios-7/
    iOS 6 Wifi Problems/Fixes
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    iPad: Issues connecting to Wi-Fi networks
    http://support.apple.com/kb/ts3304
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h Mt
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    10 Ways to Boost Your Wireless Signal
    http://www.pcmag.com/article2/0,2817,2372811,00.asp
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
    You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
    Wi-Fi or Bluetooth settings grayed out or dim
    http://support.apple.com/kb/TS1559
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

Maybe you are looking for