Will a Presario V5120NR accept ECC (vs non-ecc) memory modules?

I cannot find anything down to that that particular level in the specs on the HP website for this particular model. I know it is DDR PC2700 333, but that is a much as I can find/glean. The original memory modules currently installed in the machine (2 256mb) don't indicate either on their stickers.
Thanks!

Non-Ecc only. Max 2GB.
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

Similar Messages

Upgrade Memory on 2009 4 core Mac Pro - Max? Non-ECC?

I've been doing research on what I can do to upgrade my RAM on my Mac Pro and I think I did something I wasn't supposed to do a while back.
During my last upgrade adventure, I apparently purchased and installed a 2GB stick of Non-ECC (PC3-8500 1066MHz) RAM to fill the one empty slot. The computer shipped with 3 bars of 1GB ECC memory.
Now, as I scan the web for info on what kind of memory I can get away with, everything I'm seeing says that you should not mix ECC and Non-ECC. But I've been running both for about a year now.
So my questions:
1. Should/can I use Non-ECC Memory?
2. If so, should I not be mixing?
3. What is the Max amount of memory my Mac Pro can handle? I'm seeing some info that says 4x2GB, and I'm seeing other info that says 4x4GB. Which is correct?
Thanks.

When you get a lot of memory in a computer, it is more likely so suffer an occasional memory error. This can cause serious problems that can lie hidden for months. It can take a very long time to isolate the problem and find the bad component and remove it, and the damage may have propagated throughout the files on your Hard drive.
Use System Profiler \[About this Mac > More Info] and click the "Memory" category. You will see an indication of whether each DIMM is ECC, and also a main status of "ECC ON" or "ECC OFF".
You are very lucky to own a Mac that has additional Hardware to support Error Correcting Code ECC Memory. IF ECC is active, you get enormous peace-of-mind. Any single-bit errors will be corrected, and double bit errors will stop your Mac immediately -- long before the problem can contaminate anything else.
I suggest you use only ECC memories, and make certain ECC is always ON.
Apple does not currently sell 4GB DIMMs, but others do, as noted above. Most sellers of 4GB DIMMs also warn you that you cannot mix 4GB DIMMs with 1GB or 2GB DIMMs.

Mixing ECC and NECC (Non-ECC) RAM Modules

Hi,
I have a G5 Dual Core 2.0 with a pair of 512Mb Non-ECC (NECC) RAM installed and I want to upgrade to 3Gb. I'm thinking of getting 2Gb ECC modules and discarding the 1Mb NECC installed. But I came across a phrase in the Apple Manual of my G5 that states "DO NOT MIX ECC and NON-ECC Memory Modules WITHIN A PAIR." Does that mean I can mix ECC and NECC within Memory Banks and NOT within a PAIR? Because in that case I won't have to discard my NECC 1Gb and have a mixed 3Gb Memory!? I'm afraid to actually try it so I would appreciate your insights. Thanks much.
G5 Dual Core 2.0 Mac OS X (10.4.7)

Yes. You can mix ECC and nonECC as long as you don't pair the ECC with the nonECC. The computer will just treat all RAM as nonECC.
You can keep the original memory as long as the two 512MB DIMMs are always paired with each other.

Mixing ECC & non-ECC memory

I just inherited the care of a Dual G5 server. I noticed that there are 2-256 sticks of ECC and 2-256 sticks of non-ECC memory.
Is this an issue? Or will they work fine together?

Hi, lobsang-mack, and a Warm Welcome to Apple Discussions and the G5 Power Mac forum!
It should not cause problems. Presumably the server is working...? ECC is intended for servers and "mission-critical" applications.
Some explanation of ECC here
http://www.crucial.com/crucial/pvtcontent/memorytype.asp?model=&memtype=CHOOSE#e cc

Fireworks cs4 will not launch after accepting license agreement

fireworks cs4 will not launch after accepting license agreement

<user_name> = Your User Name:
in XP:
Application Data Path:
C:\Documents and Settings \<user_name>\Local Settings\Application Data
Fireworks CS4 Preference Folder Path:
C:\Documents and Settings \<user_name>\Local Settings\Application Data\Adobe\Fireworks CS4
Delete the Preference folder and re-launch FW.
Note: They are hidden folders, you need to uncheck the 'Show Hidden Files' and "Hide System Protected File" in Folder Options > View.
-- Sag-e-Attar Junaid Atari

I cannot send a message to a non-apple phone and an apple phone in a group message. Both of the names will turn green as though they are non-apple phones, even when one is an apple user.

I cannot send a message to a non-apple phone and an apple phone in a group message. Both of the names will turn green as though they are non-apple phones, even when one is an apple user. I am on iPhone 6. It also happens on my mom's iPhone 5s.

Send messages with your iPhone, iPad, or iPod touch - Apple Support
iOS: Troubleshooting Messages - Apple Support
Send a group message with your iPhone, iPad, or iPod touch - Apple Support

Can't access my video meetings after Lion install Flashplayer will not let me accept or deny

I can't access my online meetings after installing lion. Flashplayer will not let me accept or deny.

Yes I have tried everything. Talked with support on the phone and all they could say was it is adobe Flash players fault. They had no idea how to fix it.

If spell check in ibooks author is wrong will apple review not accept it?

In my book I mention the Chinese energy and movement art chi gung. It is also known as chi kung or qigong. It seems ibooks spell checker recognizes chi kung and qigong. But it doesn't recognize chi gung which is the correct spelling from the teaching I learned it from. And it puts a red line under it. If I leave it as chi gung will apple review not accept it? And will they send the book back for correction? If so should I just accept the fact and go with the other spelling of it. Or is there a way to mark it,say with parenthesises to show I know it is misspelled (according to them)?

I think there have been reports of books being rejected when the spelling was poor for much of the content. If the quality is low, there may be a need to do better, etc.
I don't think your example is a problem, but that is just my opinion. Only the reviewers know what they will or won't approve
Ken

Can anyone advise me when Lightroom 5 will be update to accept RAW images from Nikon D750?

Can anyone advise me when Lightroom 5 will be update to accept RAW images from Nikon D750?

Jim
Thanks just opened up Lightroom and got the update message, I'm certain when I opened up on Monday it wasn't there.
Fingers crossed just downloading now.
Thanks for the response.

Disk drive will not click or accept disks ?

Disk drive will not click or accept cd's or DVD's

What I did was I kept putting it in until it accepted it. I don't know if yours will do this. With any disc, my iMac and my mom's MBP accepted discs after about 20 tries.

My ichat will let me send video chats requests, but it will not let me accept them. What should i do? Also, sometimes it tells me i cannot add a 2nd or 3rd person to an existing chat because it is connected to AOL's relay servers. What does this mean?

my ichat will let me send video chats requests, but it will not let me accept them. What should i do? Also, sometimes it tells me i cannot add a 2nd or 3rd person to an existing chat because it is connected to AOL's relay servers. What does this mean?

Unfortunately, most of my advice is in the "hindsight is 20-20" category.
First off, I would never have purchased the peripheral accessories until the 14 day return period had expired. Second, you learned the hard way what the "14 days" really means.
Too bad you didn't do any homework, reading this and other forums and tech sites. Even word of mouth from others. That, more than anything could have steered you towards different phone choices from the get-go and I will leave that there with no further comment other than to say most of the issues you described have been discussed in this forum, ad nauseam.
Once you got into the refurbished phone exchanges, that is where things really went haywire. What someone tells you over the phone is a sketchy proposition, and when it comes down to it, it's your word against theirs.
I think Verizon tried to make it right, though. Remember, they don't make the phones. Don't throw the baby out with the bathwater.
You stated yourself you were a satisfied Verizon customer before this. Had the first two phones performed as they should, you would still be a satisfied Verizon customer.
Doubt any of that will make you any happier, but after you went through the effort of writing such a long post, I thought I'd try.

Ipad3 will not let me accept terms and conditions after software update

I downloaded the new software and had forgotten my password so had to ask for it.Now when I turn on my ipad it goes to the terms and conditions page but will not let me accept them and has a screen behind that that says create a password but I cannot get to that without accepting terms and conditions!!!! My Ipad is a brick! Help please!

It had not turned off all the way....now that it has been off ALL the way and turned back on after a minute it let me pass.

ICAL will not let me Accept or Decline new Invites from outlook users

Hi using Ical with mobileme new calender. Ical will not let me accept or decline any new meeting invites or change and updated invites sent to me.

So as the owner of a 140 year old brand who appreciates just how important it is to continue satisfying your customers, I have to wonder just how long will it take for Apple to lose the loyalty of its raving fans?
I love my iPad . . . except that it won't work with Adobe Flash which makes it kind of useless for many sites that I visit.
I love my iPhone, unless I actually want to use it outside of my home (Cincinnati is always 10 years behind, and our AT&T network is all but downtown for large parts of the day).
And I love my iMacs, so much so that I paid big bucks to integrate it into my office network (I am the CEO, so I can do that) and convinced my wife, mother and mother-in-law to switch from PCs.
Life was grand, integrated, happy!
And now, the MobileMe upgrade, which tried (unsuccessfully) to force me to Snow Leopard (I was able to complete the upgrade manually); then refused to work with Google Calendar (annoying, but I switched my wife's calendar to MobileMe and eliminated the need for Google Cal); but now, I cannot get Outlook notifications to work. Really?
If Apple is going to now be **** bent on making sure that their products are completely incompatible with Microsoft and Google, then I may have to switch back. I understand that Windows 7 is much better than the old XP that I gladly left behind. My cousin has an Android phone which appears to work great. There are now a plethora of new tablet PCs running Android that all appear to be great. And my wife was happy with Google calender and Google Docs, so maybe technology has finally evolved to the point that we no longer need Apple, Steve Jobs or his arrogant my way or the highway brilliance any more.
It is a sad day. I loved Apple. I admired Steve Jobs. But frankly, I feel that my loyalty is being taken for granted by an arrogant company that no longer gives a **** about its customers wants and needs. I NEED Apple devices that can work and play nice with Google, Outlook and Adobe Flash. And Mr. Jobs, if you are too **** proud to deliver this kind of functionality to your customers, the day is fast approaching (and may already be here) when I can find other companies that are willing to do whatever it takes to make my life just a little bit easier. My loyalty is not free, but comes at a price: namely, that you respect me as a customer. The Apple that I knew AND LOVED is fast losing its shine. Does anyone care?
Richard Graeter

Will my macbook 401 accept 8500 ram upgrade?

will my macbook 401 accept 8500 ram upgrade?

The model 5,1 (Late 2008,Aluminum Unibody), the model 6,1 (Late 2009, WhiteUnibody) and the model 7,1 (Mid 2010, White Unibody) can use up to 8gb of 1066mhz PC3-8500 RAM. These are the only MacBooks that can use PC3-8500 RAM.
To see which model you have go to the Apple in the upper left corner and select About This Mac, then click on More Info. When the System Profiler comes up check the Model Identifier.

What is the difference between ECC 5 and ECC 6.0

Dear Experts,
Can any one tell me in detail the difference between SAP R/3 versions ECC 5 and ECC 6 functionality wise in MM mdoule?
To be specific what are the new features in MM being added in ECC 6.0 when compared with ECC 5.
Request your help in this regard.
Rgds,
Uzair
Edited by: Mohd Uzair Hussain on Jul 23, 2008 5:35 PM

Hi,
Refer following link;
[SAP ERP Solution Browser|http://solutionbrowser.erp.sap.fmpmedia.com/]
Following are the basic differences as far as MM Module is concerned;
Pickup list - Batch where-used list display in transaction MB56
u2022 Until release 4.7, the top-down and bottom-up analyses in the function pickup list for batch where-used list (transaction MB5C) were displayed only in the form of simple output lists. As of release 6.00 of SAP ERP Central Component, the function pickup list for batch where-used list branches to the batch where-used list itself (transaction MB56).
u2022 In addition, user can define how the data in the batch where-used list is displayed, in the initial screen.
u2022 User can use all the settings available in the batch where-used list. For example, he can expand transfer posting or display vendor batch. However, it is not possible to limit the selection to valid plants in the initial screen of the pickup list.
Usability enhancements for transaction MIGO for the posting of goods movements
u2022 For goods movements that refer to purchase orders as reference documents (for example, goods receipt, goods issue, subsequent adjustment), user can specify the ordering plant as an additional selection criterion directly next to the purchase order number and the item number.
u2022 There is a new default value: "copy account assignment fields." When entering other goods receipts, user can copy existing account assignment data from the previous item to use as the default values for a new item. To do this, user has to set the copy account assignment fields indicator in the default values.
u2022 User changes the default values in the menu path "Settings -> Default Values."
u2022 Goods movement is monitored with reference to a material document. When you enter the following goods movements, it is possible to specify a material document, such as the following, as the reference document:
- Goods receipt
- Goods issue
- Transfer posting
- Remove from storage
u2022 Note that these material documents must be documents that have arisen from a goods movement without reference ("Others") and that are not reversal documents.
New report : display list of invoice documents (MIR5)
u2022 Logistics invoice verification offers a new report display list of invoice documents (RMMR1MDI), w hich user can use to display such a list (Transaction is MIR5).
u2022 As an addition to the existing program invoice overview (transaction code MIR6), user have extended selection criteria and display options. For example, on the initial screen user can make selections by one-time customers, invoice gross amount, and entry date.
u2022 User can also show an expert mode, which enables him to select at plant level by FI document, GL A/c posting, and Material Posting.
u2022 In the output list, the report shows both posted and held invoices.
u2022 It does not show invoices without a corresponding FI document; such as invoices planned for verification in the background or which the software has already verified as containing errors.
Requirement prioritizations in materials management
u2022 With Requirement Prioritization functionality user can assign requirement urgency at item level in purchasing and reservation documents.
u2022 The software determines the relevant requirement priority (overall priority) of a material requisition from the combination of requirement urgency group and organizational priority.
Mass maintenance of outline agreements
The following two transactions available:
u2022 Mass maintenance for contracts: transaction code MEMASSCONTRACT
u2022 Mass maintenance for scheduling agreements: transaction code MEMASSSA
Commitment plan for purchase contracts
u2022 With the function of the commitment plan for purchase contracts, it is possible to pre plan value consumption for a purchase contract.
u2022 To this end, a commitment plan is generated for each document item of the relevant contract.
u2022 This commitment plan itself can have any number of items.
u2022 User can define a value and a validity date for each commitment plan item.
u2022 This enables user to pre plan different values for different periods of time.
u2022 The software generates an earmarked fund document for a defined commitment plan item.
u2022 This earmarked funds document can in turn contain several different items with different account assignments.
u2022 The software adopts these account assignments from the item account assignments of the commitment plan.
u2022 If a purchase requisition or purchase order references this contract, the earmarked funds document is copied into the purchase order, and the account assignment is adopted from that document.
u2022 Account assignment to a different account assignment object is then no longer allowed.
Availability check in "Enjoy purchase order and requisition"
u2022 Display and checking of availability are invokable separately in the "Enjoy purchase order and requisition" function, in line with the software behavior on the sales side.
u2022 User invoke the display and checking of availability in the "Enjoy purchase order" function (transaction code ME21N) and the "Enjoy purchase requisition" function (transaction code ME51N) as follows:
- To display the availability overview, choose the menu path "Environment -> Availability." - To check availability, choose the "Check Availability" icon.
- Until this release, if user carried out the availability check for an item of a stock transport order, the software adopted confirmations as per the desired date/time only.
u2022 Two settings are possible with availability check:
- Confirmation as per desired date/time (this is the standard setting and corresponds to previous software behavior)
- Delivery proposal - Full confirmation
External services: putting service items in the purchase order on hold (changed)
User can put purchase orders with service items on hold if these items do not contain any errors. Purchase orders with service items can also be put on hold if errors occur only at header level or as a result of the availability check.
Customizing transactions OX18 replaced by view
The assigned customizing transactions have been replaced by the following view in the following implementation guide activity in customizing for the enterprise structure: Assign plant to company code: transaction OX18 replaced by view V_T001K_Assign. One will find this activity in the implementation guide under the menu path "Enterprise Structure -> Assignment -> Logistics General -> Assign Plant to Company Code."
Goods receipt: new movement types in inventory management
The following new movement types are available in inventory management:
- 107: Goods receipt to valuated goods receipt blocked stock
- 109: Goods receipt from valuated goods receipt blocked stock
Prepayment of invoices
This functionality is characterized as follows:
u2022 User can trigger prepayment of vendor invoices in logistics invoice verification.
u2022 User use the prepayment function for vendors with whom organisation has a good, long-standing relationship.
u2022 The function enables payment soon after issue of the invoice and full exploitation of the date of required payment and existing cash discounts, by posting the vendor liabilities, taxes, and cash discounts in financial accounting in advance.
u2022 The software executes the payment of the invoice regardless of the relevant goods receipt and the outcome of the invoice verification check.
u2022 Most logistics invoice verification standard functions are not affected by the prepayment function.
u2022 When the software posts invoices, it continues to execute the standard checks.
u2022 If the software has already posted the prepayment document, user can make only restricted changes to the header fields of the invoice.
u2022 To ensure adequate and orderly financial accounting postings, a prepayment clearing account has been added to SAP ERP Central Component.
u2022 Upon prepayment, the software debits this account and then settles the account again after executing the check.
Purchasing accounting information to the former SAP Business Information Warehouse
u2022 With the transfer of the purchasing account information to the former SAP Business Information Warehouse component (whose functionality is now part of SAP Net Weaver), it is now possible to maintain Info Cubes, reports, and queries that can determine how and where the costs from purchasing documents have been assigned and controlled.
u2022 As part of the software, a new data source (2LIS_02_ACC) has been created and the purchasing extraction process extended to cover the account information for purchasing orders, schedule agreements, and contracts.
Automatic settlement of planned delivery costs with evaluated receipt settlement (MRDC)
u2022 A new report (RMMR1MDC), available within the logistics invoice verification, can be used to automatically settle planned delivery costs.
u2022 To invoke the report, from the SAP easy access screen, choose the menu path "Logistics -> Materials Management -> Logistics Invoice Verification -> Automatic Settlement -> Automatic Delivery Cost Settlement" (transaction code MRDC).
u2022 Functionality for report RMMR1MRS is enhanced.
u2022 User can use the report RMMR1MRS, "Evaluated receipt settlement with logistics invoice verification (LIV)" (transaction code MRRL), to settle planned delivery costs in addition to goods and service items within logistics invoice verification.
u2022 To do so, set the relevant indicator on the initial screen of the report.
Parking service items
It is now possible to put service orders without errors or with commitment errors on hold.
Report MB5B : Stock on Posting Date
u2022 This Report is available with u201CNon-Hierarchyu201D display option which provides details of Opening, Receipt, Issue and Closing balances of Stock with quantity and value both for a given period.
u2022 This functionality is not available in Release 4.7.
Stock Transfer Between Storage Locations
u2022 Function of stock transport orders between storage locations is available from ECC 6.0 onwards.
u2022 As a result of which user can input issuing storage location with supplying plant.
u2022 Facility of using different delivery types for different issuing storage locations is available.
u2022 Shipping Point data can also be determined based on the issuing storage location

Will a Presario V5120NR accept ECC (vs non-ecc) memory modules?

Similar Messages

Maybe you are looking for