Will a Quicksilver cpu work in a Sawtooth?

I have a chance to get a Quicksilver processor (733) with heatsink and all for pretty cheap, but I don't know if it will even work in my Sawtooth.
Also, what about a cpu from a MDD G4?
Thanks in advance,
Matt

Hi Matt
A CPU from a MDD won't work due to the architectural differences (DDR RAM etc). A CPU from a QuickSilver can be made to work although I believe there are a number of issues. I expect Hussein could provide much more information, but the CPU daughter card from a QuickSilver requires a 12 volt feed to one of the securing screws. Also the bus multipler for the QuickSilver 733MHz processor will be set to 5.5 (5.5 x 133MHz = 733MHz). On a Sawtooth with a 100MHz bus, this would presumably cause the processor to run at only 550MHz. You could change the bus multiplier, but this involves adding and/or removing resistors. I believe there may also be issues with the larger QuickSilver heatsink not fitting properly, although I'm sure Hussein could provide you with more details.
I hope this helps a little.

Similar Messages

Will T7700 intel CPU work in a T61?

Will CPU work without any major upgrades? Also, what is the max mem RAM
alllowed in T61? Seller is telling me only 3gb but web says upto 6(?)
Thanks all!
Solved!
Go to Solution.

Welcome to the Forum!
yes, T7700 (2.4GHZ) CPU is a Merom processor and compatible with any T61 or T61p. If you encounter a blank screen upon installing the T7700 CPU, then you may need to update your BIOS. However, I would not recommend updating BIOS unless absolutely necessary as a failed BIOS update can brick your computer.
As for maximum memory, T61 can definitely take 2x 4GB= 8GB total DDR2 RAM despite the outdated documentation, (see here for example), which may lead some to believe it is limited to 6GB or 4GB. If you install a 32-bit operating system you will be limited to a little over 3GB. You will need a 64-bit operating system to access the full 8GB.
Have a great day. (I do not work for Lenovo)

To The Above Post: Will this CPU work with this MOBO.....

Just a FYI the Link for the CPU compatibility checker 404s when I click on it.

he means that sticky topic "Will this CPU work on my board?" ==> "https://forum-en.msi.com/index.php?topic=129204.0"
some of the links there are invalid
EDIT: I've corrected them

Will these work on a Sawtooth G4?

Would a 733 Mhz G4 processor pulled from a Power Mac G4 (Digital Audio) work on a sawtooth? My only concern was the bus speed. I know the 733 Mhz G4s have a 133 Mhz system bus and my sawtooth only has a 100 Mhz frontside bus. Would it matter?

Hi! If it were to work, you are looking at only 550mhz. Given the fact that your machine is a sawtooth, I highly doubt its possible to install successfully that large CPU in there. You would have to get rid of the IDE controller by desoldering it in order to make it fit..
You have two options though.. I would goto www.otherworldcomputing.com and get yourself a nice dual processor, or you could put the sawtooth on ebay and use the money from that(older computers, esp mac hold value nicely) and put it towards a nice Mirror Drive Door dual 1.25 or dual 1.42 system for less than what it would cost for the upgrade processor.
With the mirror drive door models, make sure you get one that has a quiet power supply and if you plan to use classic OS, one that boots directly into OS 9.2.2 - Also, make sure the seller has the actual restore/install cd package, as without this, there is no other way to install OS 9.2.2 successfully.
If you don't use classic, nor have a use for OS 9.2.2, then get a FW800 mirror drive door, or if you need more power for pro apps, a low end G5.

Quicksilver CPU upgrade question

Hi, I've got a 733mhz quicksilver G4. I'm looking into upgrading to a dual 800mhz quicksilver cpu. Sound like a plan? I know not to get an mdd cpu as I've heard they won't work in the quicksilvers. Does this sound like a plan, the dual 800mhz?....is it worth it/ do you think I'll see a difference? The only thing this computer is mainly used for is online...it's a clean system, yet with all the moving ads they keep putting on yahoo, weather.com, etc...the single 733mhz is seeming a bit slow...even with a good amount of ram I have in there. Will this swap be a simple one 'pop out, pop in'....or is there anything I need to do since it's a double on mb with originally a single cpu? Thanks for your advice! How do you calculate the cpu speed...i know that this dual 800mhz is not the same as a 1.6ghz, but what would you call it equivalent to? Thanks for your advice-
Message was edited by: funylinks2004

Hi-
Any of the Quicksilver CPUs are plug and play/ interchangeable in the QS.
Just get the heatsink with it, as they vary. Dual processors must have a dual processor specific heatsink.
A dual 800 is equivalent to a 800 Mhz processor,except that there are two of them, that's all.
It is better than the QS single 800 MHz processor in that the single doesn't have a L3 cache.
What a dual does for you is to help with multitasking in OS X, speed up dual processor aware software and boost graphics and video handling ability.
A single 933 MHz processor is quite a bit faster than a 800 MHz processor, and way better than the 733 MHz processor due to L3 cache.
However, the dual 800 also has the L3 cache, so it will feel a bunch faster than the 733.

Quicksilver cpu fan replacement question

Hi,
I have 2001 quicksilver 867. The cpu fan had stopped moving. I got it going again by taking it out and moving the fins around, but i'm looking for a replacement.
I found the "OEM" versions but the idea of spending $60 for a fan isn't that appealing.
So i'm considering just getting a standard 3 pin fan, and using an adapter to make it 2 pins.
I was thinking of getting this fan:
http://www.performance-pcs.com/catalog/index.php?mainpage=product_info&cPath=51&productsid=133
and I noticed they have several "2 pin" fan adapters here:
http://www.performance-pcs.com/catalog/index.php?cPath=289&main_page=index
So my questions are:
(1) Will that fan above work well enough for the quicksilver cpu?
(2) Do you know which 2 pin adapter would fit the logic board, as they have several types. Type A would be my guess but it's hard to tell from the small pictures.
Thanks!
David Kiley

I would remove the fan and take it to a local PC store. You should be able to find a reasonably priced replacement at most PC parts retailers.

After installing yosemite on my laptop, once I open the internet through Safari, it at times will freeze or discontinue working causing me to close the wifi and turn it back on then reload the internet page to get it to work again. How to fix please?

After installing yosemite on my laptop, once I open the internet through Safari, it at times will freeze or discontinue working causing me to close the wifi and turn it back on then reload the internet page to get it to work again. Is there any way to fix this?

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
The test works on OS X 10.7 ("Lion") and later. I don't recommend running it on older versions of OS X. It will do no harm, but it won't do much good either.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of it have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message. See, for example, this discussion.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. Try to test under conditions that reproduce the problem, as far as possible. For example, if the computer is sometimes, but not always, slow, run the test during a slowdown.
You may have started up in "safe" mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(1310 ' 0.5 0.25 50 1000 15 5120 1000 25000 6 6 5 1 0 100 ' 51 25600 4 10 25 5120 102400 1000 25 1536 500 40 500 300 85 25 20480 262144 20 2000 524288 604800 5 1024 25 50 );k=({Soft,Hard}ware Memory Diagnostics Power FireWire Thunderbolt USB Bluetooth SerialATA Extensions Applications Frameworks PrefPane Fonts Displays PCI UniversalAccess InstallHistory ConfigurationProfile AirPort 'com\.apple\.' -\\t N\\/A 'AES|atr|udit|msa|dnse|ax|ensh|fami|FileS|fing|ft[pw]|gedC|kdu|etS|is\.|alk|ODSA|otp|htt|pace|pcas|ps-lp|rexe|rlo|rsh|smb|snm|teln|upd-[aw]|uuc|vix|webf' OSBundle{Require,AllowUserLoa}d 'Mb/s:Mb/s:ms/s:KiB/s:%:total:MB:total:lifetime:sampled:per sec' 'Net in:Net out:I/O wait time:I/O requests:CPU usage:Open files:Memory:Mach ports:Energy:Energy:File opens:Forks:Failed forks:System errors' 'tsA|[ST]M[HL]' PlistBuddy{,' 2>&1'}' -c Print' 'Info\.plist' CFBundleIdentifier );f=('\n%s'{': ','\n\n'}'%s\n' '\nRAM details\n%s\n' %s{' ','\n'{"${k[22]}",}}'%s\n' '%.1f GiB: %s\n' '\n    ...and %d more line(s)\n' '\nContents of %s\n    '"${k[22]}"'mod date: %s\n    '"${k[22]}"'size (B): %d\n    '"${k[22]}"'checksum: %d\n%s\n' );c=(879294308 4071182229 461455494 216630318 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 2636415542 3694147963 1233118628 2456546649 2806998573 2778718105 842973933 1383871077 1591517921 676087606 1445213025 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 3374894509 1051159591 892310726 1707497389 523110921 2883943871 3873345487 );s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[4]} ' s/:$//;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[9]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of|yc/!{ s/^.+is |\.//g;p;q;} ' ' BEGIN { FS="\f";if(system("A1 42 83 114")) d="^'"${k[21]}"'launch(d\.peruser\.[0-9]+|ctl\.(Aqua|Background|System))$";} { if($2~/[1-9]/) { $2="status: "$2;printf("'"${f[4]}"'",$1,$2);} else if(!d||$1!~d) print $1;} ' ' $1>1{$NF=$NF" x"$1} /\*/{if(!f)f="\n\t* Code injection"} {$1=""} 1;END{print f} ' ' NR==2&&$4<='${p[7]}'{print $4} ' ' BEGIN{FS=":"} ($1~"wir"&&$2>'${p[22]}') {printf("wired %.1f\n",$2/2^18)} ($1~/P.+ts/&&$2>'${p[19]}') {printf("paged %.1f\n",$2/2^18)} ' '/YLD/s/=/ /p' ' { q=$1;$1="";u=$NF;$NF="";gsub(/ +$/,"");print q"\f"$0"\f"u;} ' ' /^ {6}[^ ]/d;s/:$//;/([^ey]|[^n]e):/d;/e: Y/d;s/: Y.+//g;H;${ g;s/ \n (\n)/\1/g;s/\n +(M[^ ]+)[ -~]+/ (\1)/;s/\n$//;/( {8}[^ ].*){2,}/p;} ' 's:^:/:p;' ' !/, .+:/ { print;n++;} END{if(n<'{${p[12]},${p[13]}}')printf("^'"${k[21]}"'.+")} ' '|uniq' ' 1;END { print "/L.+/Scr.+/Templ.+\.app$";print "/L.+/Pri.+\.plugin$";if(NR<'{${p[14]},${p[21]}}') print "^/[Sp].+|'${k[21]}'";} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:.+//p;' '&&echo On' '/\.(bundle|component|framework|kext|mdimporter|plugin|qlgenerator|saver|wdgt|xpc)$/p' '/\.dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".","");print $0"$";} END { split("'"${c[*]}"'",c);for(i in c) print "\t"c[i]"$";} ' ' /^\/(Ap|Dev|Inc|Prev)/d;/((iTu|ok).+dle|\.(component|mailbundle|mdimporter|plugin|qlgenerator|saver|wdgt|xpc))$/p;' ' BEGIN{ FS="= "} $2 { gsub(/[()"]/,"",$2);print $2;} !/:/&&!$2{print "'${k[23]}'"} ' ' /^\//!d;s/^.{5}//;s/ [^/]+\//: \//p;' '>&-||echo No' '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[2]}'{$2=$2-1;print}' ' BEGIN { M1='${p[16]}';M2='${p[18]}';M3='${p[8]}';M4='${p[3]}';} !/^A/{next};/%/ { getline;if($5<M1) o["CPU"]="CPU: user "$2"%, system "$4"%";next;} $2~/^disk/&&$4>M2 { o[$2]=$2": "$3" ops/s, "$4" blocks/s";next;} $2~/^(en[0-9]|bridg)/ { if(o[$2]) { e=$3+$4+$5+$6;if(e) o[$2]=o[$2]"; errors "e"/s";next;};if($4>M3||$6>M4) o[$2]=$2": in "int($4/1024)", out "int($6/1024)" (KiB/s)";} END { for(i in o) print o[i];} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/)||(/v6:/&&$2!~/A/) ' ' BEGIN{FS=": "} /^ {10}O/ {exit} /^ {0,12}[^ ]/ {next} $1~"Ne"&&$2!~/^In/{print} $1~"Si" { if(a[2]) next;split($2,a," ");if(a[1]-a[4]<'${p[5]}') print;};$1~"T"&&$2<'${p[20]}'{print};$1~"Se"&&$2!~"2"{print};' ' BEGIN { FS="\f";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1;} ' ' BEGIN { split("'"${p[1]}"'",m);FS="\f";} $2<=m[$1]{next} $1==9||$1==10 { "ps -c -ouid -p"$4"|sed 1d"|getline $4;} $1<11 { o[$1]=o[$1]"\n    "$3" (UID "int($4)"): "$2;} $1==11&&$5!~"^/dev" { o[$1]=o[$1]"\n    "$3" (UID "$4") => "$5" (status "$6"): "$2;} $1==12&&$5 { "ps -c -ocomm -p"$5"|sed 1d"|getline n;if(n) $5=n;o[$1]=o[$1]"\n    "$5" => "$3" (UID "$4"): "$2;} $1~/1[34]/ { o[$1]=o[$1]"\n    "$3" (UID "$4", error "$5"): "$2;} END { n=split("'"${k[27]}"'",u,":");for(i=n+1;i<n+4;i++)u[i]=u[n];split("'"${k[28]}"'",l,":");for(i=1;i<15;i++) if(o[i])print "\n"l[i]" ("u[i]")\n"o[i];} ' ' /^ {8}[^ ]/{print} ' ' BEGIN { L='${p[17]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n    "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n    [N/A]";"cksum "F|getline C;split(C, A);C=A[1];"stat -f%Sm "F|getline D;"stat -f%z "F|getline S;"file -b "F|getline T;if(T~/^Apple b/) { f="";l=0;while("'"${k[30]}"' "F|getline g) { l++;if(l<=L) f=f"\n    "g;};};if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F"\n    '"${k[22]}"'"T;printf("'"${f[8]}"'",F,D,S,C,f);if(l>L) printf("'"${f[7]}"'",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' 's/^.{52}(.+) <.+/\1/p' ' /id: N|te: Y/{i++} END{print i} ' ' /kext:/ { split($0,a,":");p=a[1];k[S]='${k[25]}';k[U]='${k[26]}';v[S]="Safe";v[U]="true";for(i in k) { s=system("'"${k[30]}"'\\ :"k[i]" \""p"\"/*/I*|grep -qw "v[i]);if(!s) a[1]=a[1]" "i;};if(!a[2]) a[2]="'"${k[23]}"'";printf("'"${f[4]}"'",a[1],a[2]);next;} !/^ *$/ { p="'"${k[31]}"'\\ :'"${k[33]}"' \""$0"\"/*/'${k[32]}'";p|getline b;close(p);if(b~/ .+:/||!b) b="'"${k[23]}"'";printf("'"${f[4]}"'",$0,b);} ' '/ en/!s/\.//p' ' NR>=13 { gsub(/[^0-9]/,"",$1);print;} ' ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?'${k[32]}'$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ / [VY]/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' '/^find: /!p;' ' /^p/{ s/.//g;x;s/\nu/'$'\f''/;s/(\n)c/\1'$'\f''/;s/\n\n//;p;};H;' ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */    /;p;' ' s/^.+ |\(.+$$//g;p;' '1;END{if(NR<'${p[15]}')printf("^/(S|usr/(X|li))")}' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' ' $3~/^[1-9][0-9]{0,2}(\.[1-9][0-9]{0,2}){2}$/ { i++;n=n"\n"$1"\t"$3;} END{ if(i>1)print n} ' s/{'\.|jnl: ','P.+:'}'//;s/ +([0-9]+)(.+)/\2'$'\t\t''\1/p' ' /es: ./{ /iOS/d;s/^.+://;b0'$'\n'' };/^ +C.+ted: +[NY]/H;/:$/b0'$'\n'' d;:0'$'\n'' x;/: +N/d;s/://;s/\n.+//p;' ' 1d;/:$/b0'$'\n'' $b0'$'\n'' /(D|^ *Loc.+): /{ s/^.+: //;H;};/(B2|[my]): /H;d;:0'$'\n'' x;/[my]: [AM]|m: I.+p$|^\/Vo/d;s/(^|\n) [ -~]+//g;s/(.+)\n(.+)/\2:\1/;s/\n//g;/[ -~]/p;' 's/$/'$'\f''(0|-(4[34])?)$/p' '|sort'{'|uniq'{,\ -c},\ -nr} ' s/^/'{5,6,7,8,9,10}$'\f''/;s/ *'$'\f'' */'$'\f''/g;p;' 's/:.+$//p' '|wc -l' /{\\.{kext,xpc,'(appex|pluginkit)'}'\/(Contents\/)?'Info,'Launch[AD].+'}'\.plist$/p' 's/([-+.?])/\\\1/g;p' 's/, /\'$'\n/g;p' ' BEGIN{FS="\f"} { printf("'"${f[6]}"'",$1/2^30,$2);} ' ' /= D/&&$1!~/'{${k[24]},${k[29]}}'/ { getline d;if(d~"t") print $1;} ' ' BEGIN{FS="\t"} NR>1&&$NF!~/0x|\.([0-9]{3,}|[-0-9A-F]{36})$/ { print $NF"\f"a[split($(NF-1),a," ")];} ' '|tail -n'{${p[6]},${p[10]}} ' s/.+bus /Bus: /;s/,.+[(]/ /;s/,.+//p;' ' { $NF=$NF" Errors: "$1;$1="";} 1 ' ' 1s/^/\'$'\n''/;/^ +(([MNPRSV]|De|Li|Tu).+|Bus): .|d: Y/d;s/:$//;$d;p;' ' BEGIN { RS=",";FS=":";} $1~"name" { gsub(/["\\]/,"",$2);print $2;} ' '|grep -q e:/' '/[^ .]/p' '{ print $1}' ' /^ +N.+: [1-9]/ { i++;} END { if(i) print "system: "i;} ' ' NF { print "'{admin,user}' "$NF;exit;} ' ' /se.+ =/,/[\}]/!d;/[=\}]/!p ' ' 3,4d;/^ +D|Of|Fu| [0B]/d;s/^ |:$//g;$!H;${ x;/:/p;} ' ' BEGIN { FS=": ";} NR==1 { sub(":","");h="\n"$1"\n";} /:$/ { l=$1;next;} $1~"S"&&$2!~3 { getline;next;} /^ {6}I/ { i++;L[i]=l" "$2;} END { if(i) print h;for(j=0;j<'${p[24]}';j++) print L[i-j];} ' ' /./H;${ x;s/\n//;s/\n/, /g;/,/p;} ' ' {if(int($6)>'${p[25]}')printf("swap used %.1f\n",$6/1024)} ' ' BEGIN{FS="\""} $3~/ t/&&$2!~/'{${k[24]},${k[29]}}'/{print $2} ' ' int($1)>13 ' p ' BEGIN{FS="DB="} { sub(/\.db.*/,".db",$2);print $2;} ' {,1d\;}'/r%/,/^$/p' ' NR==1{next} NR>11||!$0{exit} {print $NF"\f"substr($0,1,32)"\f"$(NF-7)} ' '/e:/{print $2}' ' /^[(]/{ s/....//;s/$/:/;N;/: [)]$/d;s/\n.+ ([^ ]+).$/\1/;H;};${ g;p;} ' '1;END { exit "find /var/db/r*/'${k[21]}'*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom -mtime -'${p[23]}'s"|getline;} ' ' NR<='${p[26]}' { o=o"\n"$0;next;} { o="";exit;} END{print o|"sed 1d"} ' ' {o=o"\n"$0} NR==6{p=$1*$5} END{if(p>'${p[27]}'*10^6)print o|"sed 1d"} ' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab kextfind top pkgutil "${k[30]}\\" echo cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom 'mdfind -onlyin' env pluginkit scutil 'dtrace -q -x aggsortrev -n' security sed\ -En awk 'dscl . -read' networksetup mdutil lsof test osascript\ -e netstat mdls route cat uname powermetrics codesign lockstat lpstat );c2=(${k[21]}loginwindow\ LoginHook ' /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'" 'L*/Ca*/'${k[21]}'Saf*/E* -d 2 -name '${k[32]} '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' -i '-nl -print' '-F \$Sender -k Level Nle 3 -k Facility Req "'${k[21]}'('{'bird|.*i?clou','lsu|sha'}')"' "-f'%N: %l' Desktop {/,}L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message CRne '0xdc008012|(allow|call)ing|Goog|(mplet|nabl)ed|ry HD|safe b|succ|xpm' -k Message CReq 'bad |Can.t l|corru|dead|fail|GPU |hfs: Ru|inval|Limiti|v_c|NVDA[(]|pa(gin|us)|Purg(ed|in)| err|Refus|s ful|TCON|tim(ed? ?|ing )o|trig|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o%cpu,comm,ruid' "' syscall::recvfrom:return {@a[execname,uid]=sum(arg0)} syscall::sendto:return {@b[execname,uid]=sum(arg0)} syscall::open*:entry {@c[execname,uid,copyinstr(arg0),errno]=count()} syscall::execve:return, syscall::posix_spawn:return {@d[execname,uid,ppid]=count()} syscall::fork:return, syscall::vfork:return, syscall::posix_spawn:return /arg0<0/ {@e[execname,uid,arg0]=count()} syscall:::return /errno!=0/ {@f[execname,uid,errno]=count()} io:::wait-start {self->t=timestamp} io:::wait-done /self->t/ { this->T=timestamp - self->t;@g[execname,uid]=sum(this->T);self->t=0;} io:::start {@h[execname,uid]=sum(args[0]->b_bcount)} tick-10sec { normalize(@a,2560000);normalize(@b,2560000);normalize(@c,10);normalize(@d,10);normalize(@e,10);normalize(@f,10);normalize(@g,10000000);normalize(@h,10240);printa(\"1\f%@d\f%s\f%d\n\",@a);printa(\"2\f%@d\f%s\f%d\n\",@b);printa(\"11\f%@d\f%s\f%d\f%s\f%d\n\",@c);printa(\"12\f%@d\f%s\f%d\f%d\n\",@d);printa(\"13\f%@d\f%s\f%d\f%d\n\",@e);printa(\"14\f%@d\f%s\f%d\f%d\n\",@f);printa(\"3\f%@d\f%s\f%d\n\",@g);printa(\"4\f%@d\f%s\f%d\n\",@h);exit(0);} '" '-f -pfc /var/db/r*/'${k[21]}'*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag $ -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f'$'\f''%Sc'$'\f''%N -t%F {} \;' '/S*/*/Ca*/*xpc*' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' /\ kMDItemContentTypeTree=${k[21]}{bundle,mach-o-dylib} :Label "/p*/e*/{auto*,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {/p*,/usr/local}/e*/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*{,/*} .launchd.conf" list '-F "" -k Sender hidd -k Level Nle 3' /Library/Preferences/${k[21]}alf\ globalstate --proxy '-n get default' vm.swapusage --dns -get{dnsservers,info} dump-trust-settings\ {-s,-d,} '~ "kMDItemKind=Package"' '-R -ce -l1 -n5 -o'{'prt -stats prt','mem -stats mem'}',command,uid' -kl -l -s\ / '--regexp --files '${k[21]}'pkg.*' '+c0 -i4TCP:0-1023' ${k[21]}dashboard\ layer-gadgets '-d /L*/Mana*/$USER' '-app Safari WebKitDNSPrefetchingEnabled' '-Fcu +c0 -l' -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' '-F \$Message -k Sender kernel -k Message CReq "'{'n Cause: -','(a und|I/O |gnment |jnl_io.+)err|disk.+abo','USBF:.+bus'}'"' -name\ kMDItem${k[33]} -T\ hfs '-n get default' -listnetworkserviceorder :${k[33]} :CFBundleDisplayName $EUID {'$TMPDIR../C ','/{S*/,}'}'L*/{,Co*/*/*/L*/}{Cache,Log}s -type f -size +'${p[11]}'M -exec stat -f%z'$'\f''%N {} \;' \ /v*/d*/*/*l*d{,.*.$UID}/* '-app Safari UserStyleSheetEnabled' 'L*/A*/Fi*/P*/*/a*.json' users/$USER\ HomeDirectory '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' ' -F "\$Time \$(Sender): \$Message" -k Sender Rne "launchd|nsurls" -k Level Nle 3 -k Facility R'{'ne "user|','eq "'}'console" -k Message CRne "[{}<>]|asser|commit - no t|deprec|done |ect pas|fmfd|Goog|ksho|ndum|obso|realp|rned f|/root|sandbox ex" ' getenv '/ "kMDItemDateAdded>=\$time.now(-'${p[23]}')&&kMDItem'${k[33]}'=*"' -m\ / '' ' -F "\$Time \$(RefProc): \$Message" -k Sender Req launchd -k Level Nle 3 -k Message Rne "asse|bug|File ex|hij|Ig|Jet|key is|lid t|Plea|ship" ' print{,-disabled}\ {system,{gui,user}/$UID} '-n1 --show-initial-usage --show-process-energy' -r ' -F "\$Message" -k Sender nsurlstoraged -k Time ge -1h -k Level Nle 4 -k Message Req "^(ER|IN)" ' '/A* -type d -name *.app -prune ! -user 0' -vv '-D1 -IPRWck -s5 sleep 1' -o );N1=${#c2[@]};for j in {0..20};do c2[N1+j]=SP${k[j]}DataType;done;l=({Restricted\ ,Lock,Pro}files POST Battery {Safari,App,{Bad,Loaded}\ kernel,Firefox}\ extensions System\ load boot\ args FileVault\ {2,1} {Kernel,System,Console,launchd}\ log SMC Login\ hook 'I/O per process' 'High file counts' UID {System,Login,Agent,User}\ services\ {load,disabl}ed {Admin,Root}\ access Font\ issues Firewall Proxies DNS TCP/IP Wi-Fi 'Elapsed time (sec)' {Root,User}\ crontab {Global,User}' login items' Spotlight Memory\ pressure Listeners Widgets Parental\ Controls Prefetching Nets Volumes {Continuity,I/O,iCloud,HID,HCI}\ errors {User,System}\ caches/logs XPC\ cache Startup\ items Shutdown\ codes Heat Diagnostic\ reports Bad\ {plist,cache}s 'VM (GiB)' Bundles{,' (new)'} Trust\ settings Activity Free\ space Stylesheet Library\ paths{,' ('{shell,launchd}\)} Data\ packages Modifications CUPS );N3=${#l[@]};for i in {0..8};do l[N3+i]=${k[5+i]};done;F() { local x="${s[$1]}";[[ "$x" =~ ^([\&\|\<\>]|$) ]]&&{ printf "$x";return;};:|${c1[30]} "$x" 2>&-;printf "%s \'%s\'" "|${c1[30+$?]}" "$x";};A0() { Q=6;v[2]=1;id -G|grep -qw 80;v[1]=$?;((v[1]))||{ Q=7;sudo -v;v[2]=$?;((v[2]))||Q=8;};v[3]=`date +%s`;date '+Start time: %T %D%n';printf '\n[Process started]\n\n'>&4;printf 'Revision: %s\n\n' ${p[0]};};A1() { local c="${c1[$1]} ${c2[$2]}";shift 2;c="$c ` while [[ "$1" ]];do F $1;shift;done`";((P2))&&{ c="sudo $c";P2=;};v=`eval "$c"`;[[ "$v" ]];};A2() { local c="${c1[$1]}";[[ "$c" =~ ^(awk|sed ) ]]&&c="$c '${s[$2]}'"||c="$c ${c2[$2]}";shift 2;local d=` while [[ "$1" ]];do F $1;shift;done`;((P2))&&{ c="sudo $c";P2=;};local a;v=` while read a;do eval "$c '$a' $d";done<<<"$v";`;[[ "$v" ]];};A3(){ v=$((`date +%s`-v[3]));};export -f A1 A2 F;B1() { v=No;! ((v[1]))&&{ v=;P1=1;};};eval "`type -a B1|sed '1d;s/1/2/'`";B3(){ v[$1]="$v";};B4() { local i=$1;local j=$2;shift 2;local c="cat` while [[ "$1" ]];do F $1;shift;done`";v[j]=`eval "{ $c;}"<<<"${v[i]}"`;};B5(){ v="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d$'\e' <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F$'\e' ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`egrep -v "${v[$1]}"<<<"$v"|sort`;};eval "`type -a B7|sed '1d;s/7/8/;s/-v //'`";C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { B4 0 0 63&&C1 1 $1;};C4() { echo $'\t'"Part $((++P)) of $Q done at $((`date +%s`-v[3])) sec">&4;};C5() { sudo -k;pbcopy<<<"$o";printf '\n\tThe test results are on the Clipboard.\n\n\tPlease close this window.\n';exit 2>&-;};for i in 1 2;do eval D$((i-1))'() { A'$i' $@;C0;};';for j in 2 3;do eval D$((i+2*j-3))'() { local x=$1;shift;A'$i' $@;C'$j' $x;};';done;done;trap C5 2;o=$({ A0;D0 0 N1+1 2;D0 0 $N1 1;B1;C2 31;B1&&! B2&&C2 32;D2 22 15 63;D0 0 N1+2 3;D0 0 N1+15 17;D4 3 0 N1+3 4;D4 4 0 N1+4 5;D4 N3+4 0 N1+9 59;D0 0 N1+16 99;for i in 0 1 2;do D4 N3+i 0 N1+5+i 6;done;D4 N3+3 0 N1+8 71;D4 62 1 10 7;D4 10 1 11 8;B2&&D4 18 19 53 67;D2 11 2 12 9;D2 12 3 13 10;D2 13 32 70 101 25;D2 71 6 76 13;D2 45 20 52 66;A1 7 77 14;B3 28;A1 20 31 111;B6 0 28 5;B4 0 0 110;C2 66;B2&&D0 45 90 124;D4 70 8 15 38;D0 9 16 16 77 45;C4;B2&&D0 35 49 61 75 76 78 45;B2&&{ D0 28 17 45;C4;};B2&&{ A1 43 85 117;B3 29;B4 0 0 119 76 81 45;C0;B4 29 0 118 119 76 82 45;C0;    };D0 12 40 54 16 79 45;D0 12 39 54 16 80 45;D4 78 46 91;D4 74 25 77 15&&{ B4 0 8 103;B4 8 0;A2 18 74;B6 8 0 3;C3 75;};B2&&D4 19 21 0;B2&&D4 40 10 42;D2 2 0 N1+19 46 84;D2 44 34 43 53;D2 59 22 20 32;D2 33 0 N1+14 51;for i in {0..2};do A1 29 35+i 104+i;B3 25+i;done;B6 25 27 5;B6 0 26 5;B4 0 0 110;C2 69;D2 34 21 28 35;D4 35 27 29 36;A1 40 59 120;B3 18;A1 33 60 121;B8 18;B4 0 19 83;A1 27 32 39&&{ B3 20;B4 19 0;A2 33 33 40;B3 21;B6 20 21 3;};C2 36;D4 50 38 5 68;B4 19 0;D5 37 33 34 42;B2&&D4 46 35 45 55;D4 38 0 N1+20 43;B2&&D4 58 4 65 76 91;D4 63 4 19 44 75 95 12;B1&&{ D4 53 5 55 75 69&&D4 51 6 58 31;D4 56 5 56 97 75 98&&D0 0 N1+7 99;D2 55 5 27 84;D4 61 5 54 75 70;D4 14 5 14 96;D4 15 5 72 96;D4 17 5 78 96;C4;};D4 16 5 73 96;A1 13 44 74 18;C4;B3 4;B4 4 0 85;A2 14 61 89;B4 0 5 19 102;A1 17 41 50;B7 5;C3 8;B4 4 0 88;A2 14 24 89;C4;B4 0 6 19 102;B4 4 0 86;A2 14 61 89;B4 0 7 19 102;B5 6 7;B4 0 11 73 102;A1 42 86 114;j=$?;for i in 0 1 2;do ((i==2&&j==1))&&break;((! j))||((i))||B2&&A1 18 $((79+i-(i+53)*j)) 107+8*j 94 74||continue;B7 11;B4 0 0 11;C3 $((23+i*(1+i+2*j)));D4 $((24+i*(1+i+2*j))) 18-4*j 82+i-16*j $((112+((3-i)*i-40*j)/2));done;D4 60 4 21 24;D4 42 14 1 62;D4 43 37 2 90 48;D4 41 10 42;D2 48 36 47 25;A1 4 3 60&&{ B3 9;A2 14 61;B4 0 10 21;B4 9 0;A2 14 62;B4 0 0 21;B6 0 10 4;C3 5;};D4 9 41 69 100;D2 72 21 68 35;D2 49 21 48 49;B4 4 22 57 102;A1 21 46 56 74;B7 22;B4 0 0 58;C3 47;D4 54 5 7 75 76 69;D4 52 5 8 75 76 69;D4 57 4 64 76 91;D2 0 4 4 84;D2 1 4 51 84;D4 21 22 9 37;D0 0 N1+17 108;D4 76 24 38;A1 23 18 28 89;B4 0 16 22 102;A1 16 25 33;B7 16;B4 0 0 34;D1 31 47;D4 64 4 71 41;D4 65 5 87 116 74;C4;B4 4 12 26 89 23 102;for i in {0..3};do A1 0 N1+10+i 72 74;B7 12;B4 0 0 52;C3 N3+5+i;((i))||C4;done;A1 24 22 29;B7 12;B3 14;A2 39 57 30;B6 14 0 4;C3 67;A1 24 75 74;B4 1 1 122||B7 12;B4 0 0 123;B3 23;A2 39 57 30;B6 23 0 4;C3 68;B4 4 13 27 89 65;A1 24 23;B7 13;C3 73;B4 4 0 87;A2 14 61 89 20;B4 0 17;A1 26 50 64;B7 17;C3 6;A1 4 88;D5 77 44 89;D4 7 11 6;D0 0 N1+18 109;A3;C2 39;C4;} 4>&2 2>/dev/null;);C5
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. If you don't know the password, or if you prefer not to enter it, just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, a series of lines will appear in the Terminal window like this:
[Process started]
        Part 1 of 8 done at … sec
        Part 8 of 8 done at … sec
        The test results are on the Clipboard.
        Please close this window.
[Process completed]
The intervals between parts won't be exactly equal, but they give a rough indication of progress. The total number of parts may be different from what's shown here.
Wait for the final message "Process completed" to appear. If you don't see it within about ten minutes, the test probably won't complete in a reasonable time. In that case, press the key combination control-C or command-period to stop it and go to the next step. You'll have incomplete results, but still something.
12. When the test is complete, or if you stopped it because it was taking too long, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak for themselves, not for me. The test itself is harmless, but whatever else you're told to do may not be. For others who choose to run it, I don't recommend that you post the test results on this website unless I asked you to.
Copyright © 2014, 2015 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

Will this hard drive work in my iMac G5?

Will this hard drive work in my G5?
http://www.amazon.com/dp/B005CT56XU/?tag=extension-kb-20
Below are the stats for my iMac.
Thanks for any help!
Processor
Memory
Processor speed:
- 2.0 GHz.
Processor Type:
- PowerPC, G5
Number of Cores:
- 1
Bus Speed:
- 667 Mhz
Cache:
64-bit Support:
- No
Turbo Boost:
- No
Installed RAM:
- CTO
Max. Amount:
- 2.0 GB
Amount of Slots:
- 2
RAM Speed:
- 400 MHz
RAM Type:
- PC-3200, DDR, SDRAM
Storage and Media
Graphics
Hard Drive:
- CTO, 7200rpm.
Hard Drive Brand:
- Unknown.
Drive Bus:
- Serial-ATA
Optical Drive:
- CTO.
Optical Bus:
- Ultra ATA/133
Other Media:
Display Size:
- 17-inch.
Graphics Card:
- ATI Radeon 9600
Card Memory:
- 128 MB
Max. Resolution:
- 1440 x 900
BLU / Coating:
- TFT LCD
Networking
Ports and Expansion
AirPort:
- Built-in AirPort Extreme (802.11 b/g)
Ethernet:
- 10/100/1000BASE-T (RJ-45)
Bluetooth:
- Built-in Bluetooth 2.0 + EDR
Infrared:
- None.
Modem:
- 56k v92
USB:
- 3 ports (USB 2.0)
FireWire:
- 2 ports (FW400).
Display port:
- Mini-VGA
Card Slot:
Thunderbolt:
- No Thunderbolt port.
Operating System and Software
Temperature and Cooling
Original OS:
- Mac OS 10.4 Tiger
Maximum OS:
- Mac OS 10.5.8
Recommended OS:
- Mac OS 10.4.11
iLife Supported:
- Coming Soon

Well, there are different versions of Sata. See:
http://en.wikipedia.org/wiki/Serial_ATA#Revisions
I think this is the info someone would need:
You may want to post machine info.
blue apple > about this mac > more info button. Click on the hardware line. It has a little triangle in front of the word hardware.
Leave out the serial number.
Example:
Machine Name: iMac
Machine Model: PowerMac4,1
CPU Type: PowerPC 750 (33.11)
Number Of CPUs: 1
CPU Speed: 600 MHz
L2 Cache (per CPU): 256 KB
Memory: 768 MB
Bus Speed: 100 MHz
Boot ROM Version: 4.1.9f1
Look around & see if you can find the bus speed for the SATA.
Robert

Will Snapz Pro X work in Mavericks?

Will Snapz Pro X work in Mavericks?

Like others, I'm finding that Snapz quits right after taking a screen shot in Mavericks. I'm trying the approach suggested here:
http://mac.tutsplus.com/tutorials/tips-shortcuts/how-to-launch-any-app-with-a-ke yboard-shortcut/
Basically, an Automator script is created and then attached to a keyboard shortcut. By using the same shortcut that used for Snaz, if Snapz isn't running, this keyboard command will launch it. I'm not sure whether this will adequately salvage the Snapz functions pending an update (in case that ever happens).
Another approach might be along the lines suggested by:
http://hints.macworld.com/article.php?story=20060927132601570
The scripts deal with relaunching Quicksilver. It seems that the Lingon app might be able to relaunch Snapz, and maybe someone knows how to rewrite the script to do the same thing without having to purchase Lingon. Any takers?
Rob

Will batman arkham asylum work in my lenovo g570 laptop

will batman arkham asylum work in my lenovo g570 laptop?

Hi
Welcome To Lenovo Community
Please find the system requirement details for batman arkham asylum to work
Minimum System Requirements:
Recommended System Requirements:
CPU:
Intel Pentium 4 3GHz or AMD Athlon 64 3500+
CPU:
Core 2 Duo E6600 (2.4Ghz) or Athlon 64 X2 4600+
RAM:
1GB for Windows XP
2GB for Windows Vista
RAM:
2GB for Windows XP
3GB for Windows Vista
VGA:
nVidia 6600 or ATI 1300
VGA:
nVidia 9800GTX or ATI 3870
DX:
DirectX 9.0c
DX:
DirectX 9.0c
OS:
Microsoft Windows XP or Vista
OS:
Microsoft Windows XP or Vista
http://gamesystemrequirements.com/
HDD:
9GB free disk space
HDD:
9GB free disk space
Sound:
Microsoft Windows XP/Vista compatible sound card (100% DirectX 9.0c -compatible)
Sound:
Microsoft Windows XP/Vista compatible sound card (100% DirectX 9.0c -compatible)
ODD:
Quad-speed (4x) DVD-ROM drive
ODD:
Quad-speed (4x) DVD-ROM drive
Network:
Recommended peripheral:
100% Windows XP/Vista compatible mouse and keyboard / Xbox 360 Controller for Windows
If Your system is having integrated card as intell the game will not work ,
if it is discreat it may work but depending upon if same is matching with the requirement mentioned above
http://gamesystemrequirements.com/games.php?id=826
Hope This Helps
Cheers!!!

Quicksilver CPU

Is it possible to drop the CPU from a newer PowerMac G4 into my Quicksilver 2002? Like the CPU from a Dual MDD, or perhaps the Dual 1Ghz from the last QuickSilver (My current G4 is a single Processor Unit)

I don't believe it's possible to drop the CPU daughter card from a MDD or FW800 PowerMac into a QuickSilver due to the differences in architecture etc. However, I'm sure the CPU card from another QuickSilver would work, including those with dual processors. I expect all QuickSilver 2002s are fundamentally the same in terms of the logic board etc, the only difference being which CPU card happened to be installed at the factory. I've tried looking for one from a Dual 1GHz QuickSilver as well so I could perform a processor upgrade without having to worry about firmware patches etc that many third party processor upgrades seem to need. However, original Apple CPU cards seem much more expensive than third party ones, even second hand. I hope this helps.

I need to upgrade my MacBook 13" white 2008 hard drive. I have found a WD6400BPVT western digital Scorpio blue 640GB (5400rpm) SATA 8MB 2.5" will this fit and work? Many thanks for any help

I need to upgrade my MacBook 13" white 2008 hard drive. I have found a WD6400BPVT western digital Scorpio blue 640GB (5400rpm) SATA 8MB 2.5" will this fit and work? Many thanks for any help

I had a 640GB HDD in my Early 2008 Macbook and it was just too much it would always freeze up the computer a bit for only a few seconds but ya. Then I realized that it was the size of the HDD that was causing it since the Early 2008 Macbook models can only handle a MAX od 500GB while the Early 2008 Macbook Pros could have a MAX of 640GB (Lucked out there!) lol But ya the Early 2008 Mocbooks can only handle a MAX HDD size of 500GB and that's it!! lol

Apple tv viera cast 2008. I want to add apple tv via hdmi connection, viera cast which has Amazon prime is already connected thru ethane port on tv. my network is wifi from APE base and APX. Will this set up work?

I want to add apple tv via hdmi connection , and I already have ethernet input of tv for my viera cast connection, which gets Amazon prime. Wireless connection is APE base and APX, Want to add
apple tv to get Netflix so I can cancel my xfinity premium channels. Will this set up work. p.s as you can tell I am a Mac novice.

Providing you have a free HDMI port on the TV and the location you would put the Apple TV will allow it to connect to your network, you should be good to go.

Will Report Builder 2012 Work with SQL Server 2008???

Simple question really
Will Report Builder 2012 work in conjunction with SQL Server 2008???
Is it worth while upgrading?
The main reason i ask is the ability to export in an xlsx format
Thanks

Hi Gmach,
The version of Report Builder on SQL Server Reporting Service (SSRS) 2012 is Report Builder 3.0. The Report Builder 3.0 manufactures 2010 RDL reports, so it only works with the version of SQL Server 2008 R2 or later. So in your scenario, we can no connect
to SQL Server 2008 Server using Report Builder that on SSRS 2012.
If you have any questions, please feel free to ask.
Regards,
Charlie Liao
TechNet Community Support

Will my ipod classic work with windows 8

I am finally updating my Windows XP desktop to a Windows 8 laptop. Will my ipod classic work with Windows 8? I've seen a ton of problems from other users with regard to compatibility.

Do yourself a big favor. Switch to Windows 7. (Or buy a Mac.)

Will a Quicksilver cpu work in a Sawtooth?

Similar Messages

Maybe you are looking for