Will Airport Extreme extend Belkin router network

I have recently had my network based on a wired D-Link router wired to Airport Extreme and it has worked fine. I have replaced the router with a Belkin Wireless router. Can I use Belkin as hub of network and use the Extreme to extend the network by placing it further down the house and then an express at the far end of the house to use airtunes. I have tried to do this with no luck. Is it possible and how do you do it.
I would really appreciate some assistance.
Thanks
Patrick

Possibly if you have either the Belkin F5D7230-4 or F5D7231 model ... as these are the only Belkins that are known to be WDS-compatible with the AirPorts.

Similar Messages

  • Setting up a WDS with airport extreme and Belkin router

    Hi,
    I had my airport extreme base station set up with a linksys router (the common one everyone has) and it worked fine. I moved and now am trying to set it up with a Belkin F5D7234-4, and have not been able to get it to work. I have tried both the WLAN and the LAN MAC addresses. Is there something I am missing? Thanks

    Unfortunately, most non-AirPort routers are not compatible with Apple's implementation of Wireless Distribution System (WDS)...so it very unlikely that your Belkin router can be extended wirelessly with the AirPort Extreme Base Station (AEBS).
    The few Belkin routers, that are known to work are models: F5D7230-4 and F5D7231

  • Extend Wireless Network using a Telstra technicolor Gateway wireless Router to Airpot extreme but Airport will only except join not extend and I can not get a network on the Airpor Extreme ethernet ports but can ping Airport extreme from Technicolor Rout/

    Extend Wireless Network using a Telstra technicolor Gateway wireless Router to Airpot extreme but Airport will only except "join a wireless network (which it does) not "extend a wireless network" (Led turns yellow and I can not get a network working on the Airpor Extreme ethernet ports but can ping Airport extreme from Technicolor Router.
    Airport gets it address DHCP.

    Funny how I can ping the Extreme but the Hard Ethernet ports dont seem to work correctly.
    When the AirPort Extreme is configured to "Join" a wireless network, the Ethernet ports are not enabled.
    Oddly, the AirPort Express has a special feature that will allow it to to "Join" virtually any wireless network.....and the Ethernet port can be enabled. So, an Express would work for your purpose to provide an Ethernet connection to the media player. This assumes that the Express is located where it can receive a strong wireless signal from your main router.
    Note that the Express will not provide any additional wireless coverage when it "Joins".

  • I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help

    I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help.
    They said I need to change my settings to NAT settings. I haven't been able to figure out or find anything. I have also spoken to Apple Support on the phone for hours without being able to figure out how to do this ( i don't think he knew much either lol.) Please help me because I've got about 15-20 devices in my house that require to be connected to the internet and this is just making things ridiculously slow and painful for me.
    Thanks!

    It is on DHCP & NAT under router mode yet my isp is still the one issuing ip addresses to my devices instead of the router issuing them

  • I am experiencing network failures with my Airport Extremes: the main router is a 2nd Gen, the extension a 5th Gen. The 5th Gen keeps on losing connection with the main router. Any ideas why?

    I am experiencing network failures with my Airport Extremes: the main router is a 2nd Gen, the extension a 5th Gen.
    The 5th Gen keeps on losing connection with the main router and thus with the internet.
    Any ideas why?

    Is the second Extreme configured to "extend" the network created by the first? If so its position must be such that it has a strong wireless connection to the first Extreme. If it is at the limits of the first one's wireless range its connection will be tenuous. Place them closer together and determine if that makes a difference.

  • Airport Extreme off a Router which provides DNS - Guest Networks

    I am sure that I am not alone here.
    I have a BTBroadband wireless ADSLModem/Router which provides DNS for the network.
    Off tyhe router is a Netgear switch which has connected to it an Airport Extreme. Also off this switch I have many other peripherals - such as Time Capsule, iMac etc.
    So the arrangement is simple in logical terms:
    BT Modem------->Wireless Router (which allocates DNS)---------->Switch----------->Airport Extreme  etc.
    IP Settings as follows
    192.168.0.1 for Wireless Router - which allocates DNS in range 192.168.0.2 to 0.150.
    I have allocated a fixed IP on the Airport Extreme of 192.168.0.151
    The devices thart run off this are all having DNS allocated by the router - not the Airport Extreme.
    So - how do I set up (or can I set up) the Guest Wireless Network?
    Let's assume Router Wireless Network is call MainWireless with a Password MainWord, The Airport Extreme is acting in Bridge Mode and has the exact same 'Create a wireless network' called MainWIreless and Password MainWord (as per best practices in using these to provide the best 'network hopping' capabilities for devices (I actually have 2 other wireless devices from TimeCapsules that operate the wireless in the same way).
    All of this works fine.
    However when I set up the Guest Network on the Airport Extreme - simply by enabling it - I provide a new Guest Network name of GuestWireless with a password GuetsPassword. In theory it should all work fine, however the devices connecting to the Guest Network cannot get to the internet (effectively I don't think that the 'iPhone for example' is being allocated a correct IP Address - in fact I know that it isn't as its a 169 range and a different subnet).
    So - the only way I can think of doing this is to go into the Network Settings on the Airport Extreme, Change Bridge Mode Wireless to DHCP and NAT and then go into Network Options. Here I am a bit lost and need help.
    To summarise - Main Router Address 192.168.0.1 allocates range 192.168.0.2 to 150, Airport Extreme Address (static) address 192.168.0.151.
    Airport Extreme DHCP and NAT Network Options has:
    IPv4 DHCP Range - I have set to 192.168.0.152 to 255
    Guest IPv4 DHCP Range 10.0.0 152 to 255
    NAT Port Mapping Protocol is switched Off
    - This won't even save.
    Should be simple I would have thought. Think again...
    Please help - mwhat should I / can I do to enable a guest wireless network?

    Thanks for all that - I suspected as much (and I did mean DHCP not DNS).
    So - if I disable DHCP on the HomeHub3 IP 192.168.0.1, and set the Airport Extreme IP Address at 192.168.0.2, what do I do with DHCP and NAT settings to have a Main and Guest Wireless Network?
    I can easily change the order of things if necessary to be :
    BT Modem (192.168.0.1 with DHCP disabled)--->Airport Extreme (192.168.0.2 (set to get DNS from 192.168.0.1) )--->Switch---->Various wired and wireless devices.

  • Will Airport Extreme Network with Panasonic Viera TC-P50ST30

    Will Airport Extreme Network work properly with Panasonic Viera TC-P50ST30 HDTV?

    I don't have this particular model, but I do have a Panasonic TC-P42GT25 plasma which has no difficulties accessing the Internet through my 4th Gen AirPort Extreme Base Station or 4th Gen Time Capsule.

  • Is a Happy Marriage Possible? New Airport Extreme & ADSL Modem/Router

    Is a Happy Marriage Possible? New Airport Extreme & ADSL Modem/Router
    1. I’m writing from a rural town in Southern Nepal, very close to India. I’m planning to create a new WI-FI network at a small monastery here.  Ideally, we will have two parallel wireless networks: the first network produced by an ADSL router/modem and a second network produced by another router in “repeater” mode.
    2. Earlier, someone suggested that, when I post a question, I should provide as many details as possible about the situation here.  Forgive me if there is “too much information”.  I have to make a trip to the US to buy new networking equipment, so I very much want to get this right.  Once I return here, I’ll be pretty much stuck with whatever I get in the US.
    3. The future routers will live next to each other in an office and could be linked by a cable (if this is the best route to go).  We do not wish to “expand” the network (in the sense of making a larger WI-FI network), but rather wish to simply have two networks, hence one ADSL router/modem and one router with the “repeater” function (out-of-the-box without any jerry rigging).  Both WI-FI signals need to travel approximately 100 (largely unobstructed) feet.
    4. If my dreams come true, the second router would be an Apple Airport Extreme (AX).  An Apple router would be ideal because my experience with Apple routers is happy: they are easy to set up, reliable, and secure. Moreover, we use Apple computers and iOS devices here (and the new AX has the “ac” thing which will be preferable as we replace old machines with new ones).
    5. Yet, from reading posts and having my prior questions answered on this website, it may be that with an ADSL modem/router, all the ease and happiness of the Apple ecosystem is lost: while Apple routers seem to connect with each other easily, problems appear to arise when users try to inter-marry our non-Apple products with Apples.
    6. Our current, super-crappy 2wire 2701hg-t (ADSL modem/router) covers the 100-foot distance without a problem when it is working and there is Ethernet flowing to us.  Frequently, our connection is very bad, and I may be unfairly judging the 2wire 2701hg-t.  But, based on user reviews on the America Amazon.com, the 2wire 2701hg-t is pretty terrible: first it is simply old and second, among other problems, it seems to have a poor quality power supply unit.  I do observe that it frequently seems to be recycling from scratch as if it had turned off and restarted.  In any case, we are replacing it since it may be about 4 or 5 years old.
    7. In previous posts on this forum, “LaPastenague” responded to some of my earlier questions about AX and ADSL.  Among other things, he pointed out that (1) line-attenuation may be contributing to our poor connection and (2) we must choose a modem/router that is suitable for “long lines.”  I’ve looked at our current modem/router statistics page; however, there are no statistics for line-attenuation or noise.  (As you will see below, my strategy is to get the “better” modem/router that is suitable for long lines.)
    8. Concerning our ADSL service, these are the facts I’ve gleaned from looking at the current router’s configuration pages:
    Connection Type: PPPoE
    Currently, the router is configured to use WPA-PSK security.
    Connection Speed: Incoming: 1024 kbps & Outgoing: 509 kbps
    (The following information may be unimportant at this time.)
    Broadband Link Diagnostics:
    DSL Synchronization: UP
    G.DMT Signal: UP
    PVC Connection: UP
    PPPoE Service: UP
    PPP Authentication: UP
    IP Connection: UP
    DNS Communication: UP
    9. The ISP (Nepal Telecom) doesn’t supply a modem/router; however, they do have a list of (at times ancient) hardware and hardware vendors:
    http://www.ntc.net.np/internet/adsl/adsl_vendersConf.php
    10. Concerning what equipment is available here, what I have observed is that generally the ADSL modem/routers for sale locally, and in the far-away capital Kathmandu, and in nearby India are often also available in the United States, but they are the cheaper, older models.  I will have to buy the new equipment in the US this year.  At a different institution nearby, they are using the TP-Link modem/router td-w89016 which they purchased locally, I believe.
    11. Based in part on LaPastenague’s earlier advice, I want to buy the TP-LINK TD-W8980 N600 Wireless Dual Band Gigabit ADSL2+ Modem Router (2.4GHz 300Mbps+5Ghz 300Mbps, IPv6 Compatible). This appears to be the most popular ADSL device on Amazon now.
    Will this modem/router work EASILY with the Airport Extreme in the manner I’ve described?  That is, connecting the two with a cable and creating two WI-FI networks.
    12. Also, is it generally correct that the best way to connect them is with an Ethernet cable: https://discussions.apple.com/message/23759755#23759755 
    13. In fact, does connecting them with a cable help alleviate some of the problems that can occur between the Apple device and the ADSL modem/router?
    14. If this will work, what “mode” will the AX device be in (again, in order to have two separate networks with separate passwords)?  I have heard of the “repeater”, “roaming” , and “bridge” modes.
    15.  Are there two levels of passwords which need to be considered?  Of course, there is the network and network passwords which we create here and which will be different.  But, does the Apple also have to have the ISP password like the principle ADSL modem/router?
    16. To set this up, what information do I need from the ISP (e.g., passwords, IPs…)?
    I think there are a lot of good reasons to use an AX router. Of course, if it is just going to be very cumbersome then, we would be loosing one of the best parts of using Apple products.  So, whoever feels knowledgeable enough to reply to this post, please be sincere if you think it is better to avoid the Apple.   Apple can rest assured that I will buy other things from them!
    In that case, I’d likely buy a second TP-Link device to create a second network:
    TL-Wa801NP [AP Mode Multi-SSID Mode AP Client Mode Repeater Mode (WDS / Universal) AP+ Bridge mode (point-to-point / point to Multi-point)].
    Thank you in advance. Long live Apple!
    Message was edited by: Jess1911

    I am not sure if there are different interfaces but my 2wire does an excellent job with line info.
    I get into this from browser.. using main IP.. in my case 10.0.0.138/MDC
    In your case it should be whatever the IP of the 2wire is, followed by /mdc
    Give it a try.
    As you can see it shows vendor and loads of info about the line.
    I rate it the best domestic modem for line info.
    A good modem actually albeit a lousy router.
    MDC is the diagnostics and Management Console.
    3. The future routers will live next to each other in an office and could be linked by a cable (if this is the best route to go).  We do not wish to “expand” the network (in the sense of making a larger WI-FI network), but rather wish to simply have two networks, hence one ADSL router/modem and one router with the “repeater” function (out-of-the-box without any jerry rigging).  Both WI-FI signals need to travel approximately 100 (largely unobstructed) feet.
    You are not repeating.. you are simply setting up two routers which are interconnected, so one is dependent on the other.. ie one is your adsl modem router and that will take the main router function. Your second router is really not working as a router, but as wireless access point (and switch if you plug things in).
    That is perfectly fine. You are not roaming in this case since both routers are running different wireless names and networks.. but they are actually using same IP range.. all devices are on the one IP network with two different wireless access points.
    4. If my dreams come true, the second router would be an Apple Airport Extreme (AX). 
    Apple router is fine for this. Easy to configure out of the box.
    5. Yet, from reading posts and having my prior questions answered on this website, it may be that with an ADSL modem/router, all the ease and happiness of the Apple ecosystem is lost: while Apple routers seem to connect with each other easily, problems appear to arise when users try to inter-marry our non-Apple products with Apples.
    The problem arises when you try and interconnect using  wireless extend or repeater.. you are not using wireless to extend, you are using ethernet. Wired has no issues.
    11. Based in part on LaPastenague’s earlier advice, I want to buy the TP-LINK TD-W8980 N600 Wireless Dual Band Gigabit ADSL2+ Modem Router (2.4GHz 300Mbps+5Ghz 300Mbps, IPv6 Compatible). This appears to be the most popular ADSL device on Amazon now.
    Will this modem/router work EASILY with the Airport Extreme in the manner I’ve described?  That is, connecting the two with a cable and creating two WI-FI networks.
    It is a good choice.. It should be fine considering how poor your line is.. this modem is proving to have a couple of bugs.. it does not handle torrents well but I would suggest your system is not being used for that purpose. It has some port forwarding issues. Again you are probably not going to overload it. 
    12. Also, is it generally correct that the best way to connect them is with an Ethernet cable: https://discussions.apple.com/message/23759755#23759755
    Absolutely best.. only decent method. 
    14. If this will work, what “mode” will the AX device be in (again, in order to have two separate networks with separate passwords)?  I have heard of the “repeater”, “roaming” , and “bridge” modes.
    Bridge. Although if it gives issues there is another method, although rather complex to setup.. not something to worry about now.
    15.  Are there two levels of passwords which need to be considered?  Of course, there is the network and network passwords which we create here and which will be different.  But, does the Apple also have to have the ISP password like the principle ADSL modem/router?
    Only the adsl modem has the ISP authentication.. it is the box that does the link. The TC just piggy backs.
    The passwords on the TC are for its Admin, wireless and disk access.
    16. To set this up, what information do I need from the ISP (e.g., passwords, IPs…)?
    For ADSL you must have the PPPoE authentication username and password.
    So, whoever feels knowledgeable enough to reply to this post, please be sincere if you think it is better to avoid the Apple.
    hmmm.. I am biased because I see the issues not all the good stories..
    The latest airport and Time Capsule seem to have a few pretty severe bugs.. if they happen to hit you, they are extremely hard to fix if you are in the middle of Nepal. And Apple service centre is a long long way away.
    I cannot answer your question from the point of view of a person on the ground in remote area. If the economics of the purchase works for you, great. Go for it.
    In terms of wireless coverage.. the Asus AC models or Netgear R7000 kill the Apple. Sorry but it is just fact.
    See reviews here.
    http://www.smallnetbuilder.com/lanwan/router-charts/bar/113-5-ghz-dn-c
    That is average.. if you look at the apple router in the worst location by changing the filters, it comes out worse again.
    I cannot post the URL to our local forum here.. (apple doesn't allow it). But in testing with apple clients the asus still beat Apple router soundly.
    Pure wireless range is not the only consideration.. but in a mixed environment and since the wireless on the 8980N is not too bad.. then buy Apple router for apple client devices makes good sense.
    Maybe the older Gen5.. or two of them.. would do a better job.. with a bit more tested and known hardware.
    One thing you do need to check.
    Routers from every other brand allow you to select country. Any country from anywhere in the world. Apple routers do not.
    If you buy an airport in North America it is coded to North America and offers just a few countries.. USA, Canada I suppose.. what else is North America??
    You cannot change it to Nepal.
    To get the one for Nepal you must buy the model that covers, South Asia I guess.. I am not sure which it is.
    See what the license information is for wifi in Nepal as it might be very different to US and therefore illegal for you to run it in Nepal.
    If only the whole world would just bow to America.. we could all follow the FCC regs..
    http://en.wikipedia.org/wiki/List_of_WLAN_channels
    This only applies to the Apple.. the TP-Link etc allows you to choose Nepal or correct country regulations for wifi.
    Buying modems has one tricky bit.. that the actual adsl ATM channel is different in different parts of the world. No modem is usually impossible to setup but some can be difficult if it is pre-configured for US.. this is easy to overcome generally as you can download a firmware for another locality, so you can have local settings.

  • I have Verizon FiOS service for phone, internet and TV but I only have one TV hooked up for it for just basic cable service with no DVR and no need for widgets.  Can I use an Airport Extreme as my router and not use the FiOs router?

    I want to use an Airport Extreme as my router.  I currently have a Verizon FiOS router.  I have Verizon for phone, internet and TV.  However, TV-wise, I just have a basic service for one TV with just a regular box.  No HD, no DVR.  Don't need access to a menu, widgets, on-demand.  Can I eliminate the FiOS Router and just use the Airport Extreme and still have phone and internet?

    I know that it will increase my wireless coverage in my house but will it increase the speeds?
    Not sure what you are asking here.  The AirPort Extreme is only going to be as fast as the Internet connection that it receives.....which is 75/75. It cannot take a 75/75 connection and make it go any faster.
    If you locate the AirPort Extreme in an area where you need more wireless signal coverage, the AirPort Extreme would deliver 75/75 in that area.  But, keep in mind that the AirPort Extreme must connect to the FIOS router using a permanent, wired Ethernet cable connection.
    If you are asking if the AirPort Extreme can wirelessly connect to the FIOS modem router, and extend the FIOS wireless network, the AirPort Extreme would not be compatible with a FIOS product for that purpose.

  • Can AirPort Extreme join a wireless network and share the connection to ethernet connected devices?

    Can AirPort Extreme join a wireless network and share the connection to ethernet connected devices?

    Yes, if the AirPort Extreme is joining a wireless network that has been created by another Apple router. In this case, it will be extending the wireless network and the Ethernet ports are enabled on the "remote" AirPort Extreme.
    No, if the AirPort Extreme will be used with another router from another manfacturer.
    Ironically, the less expensive AirPort Express can do what you ask about with virtually any wireless network using a special feature called ProxySTA. It won't extend the wireless with a non-Apple router, but the Ethernet port will be enabled.

  • How can I set up an Airport Extreme as a router, in conjunction with my AT&T modem/router?

    I am trying to set up an Airport Extreme as my router, and I am currently using an AT&T modem/router combo. I am wondering what would be the easiest way to do this. Any help would be appreciated. Thanks!

    Connect an Ethernet cable from one of the LAN <-> ports on the ATT modem/router to the WAN "O" port on the AirPort Extreme. This cable must remain in place permanently.
    Open Macintosh HD > Applications > Utilities > AirPort Utility on your Mac
    Click on Other WiFi Devices
    Click on AirPort Extreme xxxxx
    The utility will take a moment to analyze the connection, then a screen similar to this will appear with your AirPort Extreme instead of an AirPort Express
    Type in a short simple name that you want to use for the wireless network
    Type in a device name for the AirPort Extreme
    Enter a password that will be used for both the AirPort Extreme and wireless network
    Verify the password
    Click Next
    The utility will setup everything for you. When the message of Setup Complete appears, click Done and close AirPort Utility.
    The AirPort Extreme wireless network is now available.

  • Will airport extreme card work on other wireless systems

    will airport extreme card work with other networking systems such as time warner cable with a router?

    Note, Airport Extreme on PowerMacs is limited to 802.11g.  If you find you get a router that is 802.11n, and have devices that need 802.11n speed, they should be on a different wireless network.  Otherwise you can set the network to be 802.11n and 802.11g for both 'n' and 'g' devices to hook up to it from the router in question.  Be sure the PowerMac in question does support Extreme, and not just the original Airport by visiting this article:
    http://support.apple.com/kb/ht1621
    And identifying your Mac in this article:
    http://support.apple.com/kb/HT3082
    If you can't find your Mac on the article, go to Apple menu -> About This Mac and tell us the Machine ID. If it is a notebook, the name of the machine is on the screen frame. If it is a machine with a display and a built-in optical drive that has no name, it may be an iMac.  That is significant as well.  Since you posted in the PowerMac forum, without telling us your machine, we can't help you further until you do.

  • Does Airport Extreme support Static Routes?

    I have client using an Airport Extreme as their Router. They currently connect to another device outside their network using AppleTalk.
    It is planned to put this device onto TCP/IP but on a different subnet (e.g. their subnet is 192.168.5.X and the device will be on say 192.168.25.X). Does Airport Extreme support (like other Routers) the ability to set up a static link to a device on a different subnet (can’t find any information in a doco or the utility) or do they need to replace this with a “real“ router?

    Sure, I could do something like route add -net 10.100.10 192.168.0.100 on every client machine on the subnet, but there is no such way to configure a web cam and similiar devices
    Any idea, Apple?

  • Installing airport extreme after a router

    when connecting an airport extreme to a router (AE after the router), should the wire from the router go into the WAN or LAN port of the AE?

    It won't matter which port you use if you configure the AirPort Extreme in Bridge Mode, which is the correct setting when you have another router ahead of the AirPort Extreme.
    All the ports become LAN ports in Bridge Mode.
    AirPort Utility >  Manual Setup
    Internet icon > Interner Connection tab > Connection Sharing = Off (Bridge Mode)
    Be sure to restart the entire network after you change the Extreme to Bridge Mode.

  • USB External HD Connected to Airport Extreme - access from outside network?

    Hi,
    Is there any type of software that I can get that would allow me to access my shared external hard drive w/ my airport extreme from outside the network, like some type of ftp server or anything that would allow me to access it from outside my home?

    A simple way would be to share it via Apple File Sharing and FTP...
    You'll need a static Ip and a hostname, although it is easy to set up if you have a dynamic Ip too...
    Creat a free hostname on "www.dyndns.com" (for example), open your AFP and FTP ports on your router, and then use sotware such as "Rumpus" for the FTP service and tell it what drive you want to share (it can be a network drive). For AFP, all you have to do is connect to the server from the finder, hitting "Go...Connect to Server.."
    I've got my extreme drive shared globally and it works fine...just need some time and patience to set up the ports and hostnames...
    If you need help on the setup just email me... [email protected] and i'll be happy to answer any questions...

Maybe you are looking for