Will Dell 2005FPW work with my Radeon 9000 Pro?

I have a ATI Radeon 9000 Pro with 64 MB VRAM in my Quicksilver and I am looking to purchase a Dell 2005FPW. Will my old 9000 Pro drive it? Will it look okay? Or do I need to upgrade my card?
Thanks!

Hi,
Welcome to the Apple Forums!
Yes.... it has one ADC and one DVI connector. As long as the Dell is DVI, no problem. If it's VGA, get an adapter for the DVI on the card.
Regards,
Dave

Similar Messages

Will Compressor 4 work with my Final Cut Pro 7 in Final Cut Studio?

I decide to use Final Cut Pro 7 instead of Final Cut Pro X to use the Apple Color. But I wonder if the Final Cut Pro 7 can render video or work with Compressor 4 instead of the Compressor 3. Any ideas of what to do?
Thank you for the answer.
Steve

This recently came up in another thread. on FCP6.
I'd say pretty much the same applies to FCP7 as FCP 6 – except that the features for C3.5 are even more comparable to C4 than are C3.0. No interoperability between the new Compressor and the legacy versions of FCP, but many of us have always just exported QT movies fron FCP and used those as source fies. That can obviously still be done "working with" C4.
Is it worth the $49 for those who own FCS3? IMO, it's doubtful unless you do a lot of Web hosting work.
Good luck.
Russ

G4 1.25GHz with ATI Radeon 9000 Pro ready for Motion?

Hi there,
I'm looking into an unexpensive way to give Motion 2 a trail, since it won't install on my old faithful G4 dual 500. Should the above configuration be enough? I have an opportunity tu buy the single processor, Airport Extreme equipped version (there were several versions produced the same year).

FYI the 9000 is a AGP (the 9200 is the PCI card)
the 9000 is lacking pixel shaders (where Motion gets it power)
I ran Motion 1 and Motion 2 since it came out on my dual 1.25 with a 9800 and it FLEW
better then a G5 with a 5200 or 9600
with this card (under $260)
http://eshop.macsales.com/item/ATI%20Technologies/100435058/
you can run motion very well for now on your system
(that page BTW pat is talking about the Standard video card not after market ones)
DAVE

Will this RAM work with a Mac Book Pro?

http://www.eworldsale.com/crucial-2gb-kit-match-pair-pc2-5300-667mhz-cl5-240-pin -ddr2-dimm566415062.html
I found that RAM, which seems like it's correct, except that further on down the page it says something about it being "SDRAM." The picture doesn't look like SDRAM, so I'm not sure. Anyone know anything about this particular RAM? Thank you.

It does NOT say ECC or Mac Pro.
It also needs to say "Fully Buffered" DIMMs (FB-DIMM).
use the crucial memory selector or www.macsales.com "TechWorks"

Radeon 9000 Pro AGP - will it work in PM G5?

Hello,
just like in my topic. I have just acquired G5 2x2 GHz (PCI-X) but with faulty graphics card. I have a spare Radeon 9000 Pro 64 MB AGP, which was pulled from G4 MDD. Will it work in G5? In theory it should as it has AGP 2x/4x 3.3 V connector, which AGP 8x is compatible with. What do you think? I'd like to use it temporarily, before I get radeon 9800 or nvidia 6800 for this G5 Thanks!

japamac wrote:
Hi-
I am aware of the AGP specs.
There is one other factor, that you have failed to consider.
Apples use of the ADC port also included use of pins in the connector that later became needed for the 8x AGP standard.
*ADC port is not a part of AGP 8x standard.* G5 uses AGP Pro port, which has somewhat longer slot, but additional pins are at the back of the card rather than front like ADC connector.
In the 4x AGP cards, the ADC port uses pins that are designated for other use in 8x.
Apple had to change the ADC port pin configuration for the G5. G4 ADC cards are not wired correctly.
I'm pretty sure, the machine will just not boot, like a 4x machine with an 8x card.
If it works, please let us know. It will be the first.
If you short out your AGP slot, you were warned.
Here you're right - ADC connector on G5-aware cards is slightly different. But keep in mind, that it is still used for ADC voltage supply, so in theory it should be enough to tape out ADC connector on 9000 Pro to not harm either mainboard or graphics card. After all, flashed Radeon 9800 boards do not have ADC connector at all
The AGP bus is 1.5 V only and is not backward compatible. Older AGP cards will not work in the Power Mac G5 computer.
This is quoted from the Apple Developer Notes for the G5.
Of course, but rv250 GPU used in 9000 pro card is 1,5 V compatible, so basically it should work...
Tough decisions. On the one side - I could wait for proper G5-aware card and install through this time system and applications using my old PCI Matrox card. On the other - seller claims that only Nvidia 6800 got faulty in this G5 when its fan stopped working. But if this is AGP port that is fired and I can't check it right away, when I get the computer... What would you do in my place?

Final Cut Pro with a ATI Radeon 9000 Pro

I have an older Power Mac G4 that I have upgraded from 400Mhz to 1.4Ghz and a ATI Radeon 9000 Pro video card. I recently bought Final Cut Pro 2.0 and do not want to upgrade the video card yet again. Does anyone know of any work around to get Final Cut Pro to work on this computer?
Details are as follows:
Error message -
The installed graphics card does not support the OpenGL features recommended by Final Cut Pro.
ATI Radeon 9000 Pro:
Chipset Model: ATY,RV250
Type: Display
Bus: AGP
Slot: SLOT-A
VRAM (Total): 64 MB
Vendor: ATI (0x1002)
Device ID: 0x4966
Revision ID: 0x0001
ROM Revision: 113-99703-107
Card # 109-99700-00
Model ATY,RV250
Vendor $1002 (4098)
ROM ATY, Radeon9000i_A
ROM# 133-99703-107
FCode Version 1.87
NDRV 1.1.0f53
VRAM 64
Any work around at all would be great. ATI told me to upgrade to 9600 AGP or 9800 AGP. I am not even sure the 9800 AGP will work on this vintage Power Mac.

It looks like http://www.apple.com/finalcutstudio/specs.html you will be able to run the basic Final Cut Pro program but, obviously, its not going to scream. Many of the individual elements of the suite i.e. Motion, Color, are not going to function as they should without a significant boost in several things, memory, processor speed, video card.
In all honesty, you should be running FCP 4.5 or 5.0 which will run very well with your hardware. But since you already have FCS2, (I assume that's what you mean, not really Final Cut 2) hang on to it for when you decide to do what all of us eventually will have to do; buy an Intel based box.
My G5 is fast approaching obsolete, and I'm just waiting for the next version of Final Cut Suite to see how much box I need to go to. Didn't think this time 19 months ago I would be saying that... but time does roll on.
You'll enjoy FCS2 (FCP6)

ATI Radeon 9000 Pro video card is conflicting with additional memory

I have a ATI Radeon 9000 Pro video card. I have a 645E Max motherboard (MS-6547). I recently purchased a 512MB dimm of Kingston PC2700 Cas 2.5 memory (KVR333X64C25/512) to go with the the 256MB dimm of the same model # above. I installed the memory and my screen stays blank. When I remove the new dimm it runs fine. I did get the memory and the motherboard tested at the store where I got the motherboard and they work fine. I came to the conclusion it was my video card when I removed all my components except the memory and the video card, and turned on the machine,nothing. I did try swiching dimm location and changing any bios settings I thought would make it work. I tried updating the video card drivers and motherboard AGP drivers. If anybody had this problem in the past could you tell me how you got it to work.

I took the board and the 2 dimms to the store where I bought them. They hooked up both dimms and a video card to the board. When it was powered up, both dimms were recognized. After I got home I proceded to determine if another component it conflicting with the memory. I started with both dimms and my video card the Radeon. I powered up with no other hardware connected and the screen remains blank. I remove the 512MB dimm and leave the 256MB dimm in, and powered up and pc booted up normally.

I have a ibook G4 which has become redundant as my phone will no longer work with the version of itunes installed (latest it can use), how can I back up my phone to transfer to a new computer (a PC now)?

My iphone 4s (7.1.1) will no longer work with my ibook G4 which is running 10.5.8. I have a PC which i'm now going to have to use, I've manually transferred my music and photos, but how do I go about transferring my contacts and calenders. What does itunes on PC sync to in terms of contacts and calenders?
Thanks!

Hi there BDempster,
You may find the information in the articles below helpful.
iOS: How to transfer or sync content to your computer
http://support.apple.com/kb/HT1296
iTunes 11 for Windows: Sync contacts, calendars, and other info with iPod, iPhone, or iPad
http://support.apple.com/kb/PH12317
You can use iTunes to sync the contacts, calendars, notes, Safari bookmarks, and email account information on your computer with your iPod, iPhone, or iPad. iTunes also syncs this information from your device to your computer—for example, if you add contacts on your iPad, syncing adds those contacts to Windows address book or Outlook Express on your computer.
-Griff W.

Will itunes 11 work with windows xp, I have ended up with this neqw version and it doesn't work , I can look at my library ,but not play and since synching my ipod it is now empty. Apple support is useless, they treat me like I'm on a Mac not a PC .

will itunes 11 work with windows xp , I have ended up with this new version after accepting an update and now although I can view my library I can't play anything and since synching my ipod it is empty. Apple support can't seem to get it's head around the fact I'm on a PC keeps asking for an apple serial number, Help!!!

Morning gedeye,
Thanks for using Apple Support Communities.
System Requirements
Windows XP Service Pack 2 or later
32-bit editions of Windows Vista or
32-bit editions of Windows 7, and Windows 8
For more information on this, take a look at this article:
http://support.apple.com/kb/DL1614
Best of luck,
Mario

Will Ipod Touch work with Windows 8

Will IPod Touch work with Windows 8? Why is that not even a listed option in the help feature?

Apple has just not got around to revising the documentation to reflect Win 8. Just use instructions for Win 7

What are the settings in Aperture to work with a Canon 9000?

What are the settings in Aperture to work with a Canon 9000? Canon website says Aperture is not supported. Is it True?

Do you mean the Canon PIXMA Pro9000 printer?
If so, does this help?
https://discussions.apple.com/thread/3681934?tstart=0

I like the idea of auto back-up for my new iMac, Ipad and PC Netbook, particularly if I can access all files and data stored on any device. But I have a Conceptronic router. Will Time Capsule work with this and how?

I like the idea of auto back-up for my new iMac, Ipad and PC Netbook, particularly if I can access all files and data stored on any device. But I have a Conceptronic router.
1. Will Time Capsule work with this and how?
2. Can my printer USB be plugged in and then shared between the devices?
3. Can I create a network and how?
4. What happend when a visitor logs onto my existing wireless router?
I'm new to Macs (well a returning user having started with Mac Plus!!) and not very technical. Any help / advice will be much appreciated.
Ray

The key to what you seem to want to do is to be able to get Apple's Time Capsule router to "join" the network that your Conceptronic router. I believe that works with some third-party routers, but I've never seen a list of those that work in such a configuration and I have no experience with Conceptronic equipment.
You might be better off with a Network-Attached Storage (NAS) device instead of a Time Capsule.

Can I connect my iPad mini to a data projector using a lightning to 30-pin adapter connected to a 30-pin to VGA connector? Or will this only work with a lightning to VGA connector.

Can I connect my iPad mini to a data projector using a lightning to 30-pin adapter connected to a 30-pin to VGA connector? Or will this only work with a lightning to VGA connector?

The lightning to 30 pin adapter does not support video as per the item description in the Apple online store:
http://store.apple.com/us/product/MD823ZM/A/lightning-to-30-pin-adapter
This adapter lets you connect devices with a Lightning connector to many of your 30-pin accessories.* Supports analog audio output, USB audio, as well as syncing and charging. Video output not supported.
You will need to the Lightning to VGA adapter directly
http://store.apple.com/us/product/MD825ZM/A/lightning-to-vga-adapter?fnode=3a
Or the Lightning Digital AV Adapter
http://store.apple.com/us/product/MD826ZM/A/lightning-digital-av-adapter
If the projector supports HDMI input.

Will apple tv work with a hdmi splitter of some kind ? TV only has 2 hdmi ports and both are in use

will apple tv work with a hdmi splitter of some kind ? TV only has 2 hdmi ports and both are being used .
If splitter will work any recomendations as to best type to use

The Hatter,
I am a novice at Mac so I read all I can. From what I understand the NEC monitors I bought require Display Port for their maximum performance. The GTX 680 only has DVI outputs. Difference from what I understand is larger bandwidth with the DP.
You said I have the 4000 for CUDA. I am not all that familiar with CUDA and when I do read about it I do not understand it.
A concern I have is, that if I connect the 2 high end NEC monitors via the 5770, using it's 2 Display Ports I would have nothing connected to the 4000. Is the 4000 doing anything with nothing connected? I read where in a PC system the 2 cards would interact but in a Mac system they do not.
Bottom line, as I see it, the 4000 will not be useful at all to me, since I want a dual monitor set-up.
So far the 5870 seems the best choice, higher band width than the 5770, and it has 2 Display Ports to optimize the NEC monitors.
I'm not sure how fine I am splitting hairs, nor do I know how important those hairs are. I am just trying to set up a really fast reliable system that will mainly be used for CS6 and LR4. Those NEC monitors are supposed to be top notch.

Will my LED 27 Cinema Display work with the new Mac Pro?

Will my LED 27 Cinema Display work with the new Mac Pro?

Mini DisplayPort (like 27" LED Cinema Display) is a direct subset of ThunderBolt (like Mac pro late 2013). It plugs right in and the display portion "just works", no adapters required.

Will Dell 2005FPW work with my Radeon 9000 Pro?

Similar Messages

Maybe you are looking for