WIll my MP drive a dell U2711

I ordered a Dell U2711 as I'm tired of waiting for Apple's new monitor offerings and I never checked if my MP will drive it ok. It has the ATI 4890 HD and the Dell the following inputs : VGA, DVI, Composite, Component, HDMI, DisplayPort.
I believe the Apple card has a mini display port and dvi out but whcih input to the Dell is used ? Will the DVI work or must I get a mini displayport to displayport cable ?
Anyone provide comments on this monitor..anyone here using it ?
Thanks

Another option is to get a mini display port to display port adapter from monoprice.com for about $10 and you can use the mini display port to drive the monitor if you need the DVI for something else on the card.

Similar Messages

Will an X220 drive a Dell UP2414Q 4K 3840 x 2160 Monitor via Display Port?

I've not been able to find any information about this on the web and there is definitely some confusion about DisplayPort versions - could some one answer the question will an X220 drive a Dell UP2414Q 4K IPS Monitor at it's native resolution of 3840 x 2160 Monitor via Display Port? Would that be at 30Hz rather than 60Hz?
Many thanks, Mark.
Solved!
Go to Solution.

The X220 will drive the Dell UP2414Q 4K resolution through Displayport. I have tested this on the Pro2840m LCD which has the same resolution. But only on 30 hz refresh rate.
The X220 with the Series 3 Workstation Dock will drive 2 of the Pro2840m through 2 separate displayport.
The X201 will also drive this 4K resolution, as long as the LCD's 4K can accept Displayport 1.1 standard (on the 1.2 standard, the LCD will stay blank).
https://www.flickr.com/photos/lead_org/14671257827/in/set-72157645860787090
the above image confirms the 4K resolution and my X220 driving that resolution @ 30 hz.
For 60 hz refresh rate on the 4K resolution with integrated Intel GPU, you need Haswell CPU with the HD5000 graphics card, anything below that will only drive the 4K resolution at 30 Hz.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

How to Dual Display with Dell U2711

Hi,
I am looking to connect my iMac (late 2013) to a Dell U2711 in a dual display configuration. I'd like to be able to use all 2560x1440 pixels of the Dell.
the Dell has DVI-D (dual channel), Displayport (not mini displayport), HDMI and VGA.
which port will give me the cleanest picture and best performance and what cable do I need to buy ? (obviously thunderbolt to something...)
thanks !

stqn wrote:
Expi1 wrote:Thanks, I'm mostly struggling with how to partition for Arch and then how to do the bootloader. I'm using Win8 64-bit and from what I understand a Legacy BIOS bootloader. I'm not entirely sure what I should be partitioning the C: into, I've done partitions before, just not for Arch and then I'm not sure whether to use GRUB or syslinux, or if I even need those. Or if I need to use GPT or MBR?
Your disk is already partitionned so you don’t have to choose between GPT or MBR, the choice is already made.
You don’t partition “C:”, that is the name of a Windows partition. You partition a drive.
Grub or syslinux, use whatever the beginners guide tells you to. Personally I think syslinux is simpler which is why I’m using it (but I’m not dual-booting, if that matters).
You’re not saying what your problem is with partitionning, so it’s hard to help.
Thanks for getting back to me, I'm not sure if I just create one large partition for Archlinux or if I have to create multiple? Where I'm also confused is with the Creating Filesystems part of the guide. I don't understand how I'd do this in Windows, or what /dev/sda1 is referring to.
As for the bootloader part, the Beginner's Guide gives you a choice between syslinux and grub, what I'm not sure about is which to use considering I'm dualbooting. How it will affect my windows bootloader, do I disregard that and use GRUB now? I'm unclear on how that works.
I'm also aware I need to disable Secure Boot, I just searched my BIOS options and couldn't find anything remotely relating to that, so I'm assuming it's not an issue since this computer was originally on Windows 7 anyway?
Thanks again, Expi.
Last edited by Expi1 (2014-03-06 19:54:30)

Using Wide Gamut (Dell u2711) With Lightroom

I have just completed an upgrade of my computer system to include 2 Dell U2711 27" monitors. I am using LR 3.5. My system is running with Windows 7 64 bit and a ATI Firepro graphics card running the displays.
Before purchasing these, and listening to the chatter on various forums I was led to belive that I was going to get garish coloration on all applications except Adobe LR and CS5. This does not seem to be the case. LR and CS5 are fine and the other applications IE and Windows Office seem to be OK as well.
These displays are calibrated at the factory.
Does anyone have any experience with these and can share any "gotchas" with me.
Henry

Well I am glad that I am taking my time on this calibration process. I thought I had it understood correctly. I am making my dialog with Dell a part of this message so you can see the exchange I had with their 2nd level of support and I am also a document from Dell engineering. Please take a look at these and I will call Dell again if necessary.
Sorry For The Long Post
Otrman
FROM MY EXCHANGE WITH DELL:
It would be excellent if I could use a calibrated “custom” present on the monitor for LR and CS5 and simply select one of the presets (sRGB or Adobe RGB) when I am not using LR and CS5.   I am not running with any monitor profile and a generic PNP driver now and I am getting much better results than I expected. I would just un-select the profile when I did not want to use the calibrated “custom” preset.
Based on the data engineering provided me in the document I sent that is correct( Yes).
From: Henry Morse [email protected]
Sent: Monday, October 31, 2011 4:30 PM
To: Glickman, David
Subject: RE: PremierColor FAQ_SVC.doc Case 844545167
David, Please just say yes or no to this:
Are you telling me that ONLY the “custom” preset will be altered and that the other presets will remain at the “factory” settings.
Yes or No, believe me it is very important and will increase sales of this monitor if this statement gets passed along as true. Is this worth a conversation between you and engineering to verify? It would be to me and the rest of us photographers. Sorry, but this statement in the documentation is not the way I used to word my writings as an electrical engineer back in the day.
Henry
From: [email protected] [email protected]
Sent: Monday, October 31, 2011 4:47 PM
To: [email protected]
Subject: RE: PremierColor FAQ_SVC.doc Case 844545167
Based on the data engineering provided me in the document I sent that is correct.
David
From: Henry Morse [email protected]
Sent: Monday, October 31, 2011 3:22 PM
To: Glickman, David
Subject: RE: PremierColor FAQ_SVC.doc Case 844545167
Importance: High
David,
I still need clarification here.
“My personal suggestion is that since you are doing custom photo/video work that these LCD are being used for, I would calibrate them for your business purposes and leave as such. With the enhanced video settings normal internet browsing and such will have better clarity.”
Are you telling me that ONLY the “custom” preset will be altered and that the other presets will remain at the “factory” settings. This is an important question for all of us who want to use this monitor for photographic work. If we photographers can have one of the presets, namely, “custom” calibrated, and the others left as shipped then we can choose the customer preset for our work and switch back to sRGB or Adobe RGB for routine office and billing functions.   If this is true, and the photography world learns of this, Dell will sell a lot of U2711s, especially considering that the U2711 is an excellent price performer. an
I have been doing research on this for myself and to share with a number of user forums on photography. I want to get right for my own use and for sharing with the photography community.
Henry
From: [email protected] [email protected]
Sent: Monday, October 31, 2011 8:26 AM
To: [email protected]
Cc: [email protected]
Subject: RE: PremierColor FAQ_SVC.doc Case 844545167
Henry,
Per the documents as with any calibration you must be careful and aware of settings you change. Use the setting CUSTOM COLOR if you want to calibrate using your own equipment as per document.
In regards to your question on your video card as the manufacture /forums recommends you should disable any color managements since you are using your own color/video calibration tools.
My personal suggestion is that since you are doing custom photo/video work that these LCD are being used for, I would calibrate them for your business purposes and leave as such. With the enhanced video settings normal internet browsing and such will have better clarity.
Have a good day.
David
From: Henry Morse [email protected]
Sent: Friday, October 28, 2011 6:08 PM
To: Glickman, David
Cc: [email protected]
Subject: RE: PremierColor FAQ_SVC.doc Case 844545167
Good Evening David,
Thank you for taking the time to discuss color management for my recently acquired U2711 monitors.
According to what we discussed when I use calibration hardware and software you mentioned that I should use only the “custom” setting and that once I calibrated the monitor “all” factory setting would be overwritten and cannot be restored. When I read the word document you sent me I believe I am seeing something that needs clarification:
Question 7 from the word document:
7.         Is it possible to revert to factory pre-tuned settings after I color calibrated my unit with my equipment?
The customer should not re-calibrate and save your result in sRGB and AdobeRGB preset modes. Once overwritten, it is not possible to revert back to factory pre-tuned setting. The customer is advised to use the "Custom Color" preset mode to do their own calibrations.
Does this mean that only the “custom” preset is altered from the factory setting to store the results of my calibration?   Does this mean that if I use the “custom” preset only for calibration that sRGB and AdobeRGP will not be changed from the factory setting? Does this mean that each of the U2711 presets have its own LUT table? Can you please clarify?
If this turns out to be the case I can use the sRGB preset, with no profile as it is now, for routine processing with non-color aware applications, and then select the newly calibrated “custom” preset when doing photo processing. Is this the case? After reading the attachment I believe I have to be very careful not to negatively affect my monitors as they cannot be reverted to factory settings.
I have done some additional research that includes the relationship between monitors and some high end graphics cards such as the ATI Firepro V5800 card I am using. This research indicates that I should disable any efforts by the graphics card to do color management lest I interfere with the efforts to calibrate the monitors.
I am probably being a bit picky but having more than 50 years in the technical end of computers I have been burned more than once having two elements of a computing system fight each other.
Again, thank you for your help on this.
Henry
From: [email protected] [email protected]
Sent: Friday, October 28, 2011 9:20 AM
To: [email protected]
Cc: [email protected]
Subject: PremierColor FAQ_SVC.doc
Good Morning Henry,
Just to follow up on our phone conversation. I have attached a word document regarding some of the question on the U2711 settings and calibration. I also have a couple of hyperlinks one to the Dell support on the monitor. Based on our conversation I believe I have answered your questions regarding the calibration of the LCD. Please let me know later or over the weekend if you still have questions and I will follow up with you on Monday if needed.
Dell manual link:
http://www.support.dell.com/support/edocs/MONITORS/U2711b/en/index.htm
I have included a couple of non-Dell support links for you to do some testing
http://www.gballard.net/psd/go_live_page_profile/embeddedJPEGprofiles.html#
http://www.lagom.nl/lcd-test/
http://yfrog.com/3u100percentrampp
Have a great weekend
David Glickman
Advanced Technical Analyst| Executive Escalations | MCP,MCDST, MCITP,MCSE
Dell | Client Resolution Expert Center, Global Services
phone +1 512 513 6078; 800 289 3355, ext. 5136078
Office hours: 7:00 am - 4:00 pm Central, Monday - Friday
Customer feedback | How am I doing? Please contact my manager, [email protected]
Confidentiality Notice | This e-mail message, including any attachments, is for the sole use of the intended recipient(s) and may contain confidential or proprietary information. Any unauthorized review, use, disclosure or distribution is prohibited. If you are not the intended recipient, immediately contact the sender by reply e-mail and destroy all copies of the original message.
FROM THE ENGINEERING DOCUMENT: (SEE QUESTION 7)
Service & Support:
1.         Can I request Dell to re-calibrate my monitor during the warranty period?
Calibration is done for only new monitors shipped from factory.
Each unit is factory-calibrated as part of the production process.
Dell will not be able to re-calibrate the monitor during warranty
Period as calibration is done only for new units.
2.         Can I request Dell to provide another Color Calibration Factory Report in the event of the loss of or damage to the report?
Each Color Calibration Factory Report is unique to each Dell monitor and cannot be reprinted.
We would recommend that the customer takes care to retain the Color Calibration Factory Report if required.
3.         Is there a specification for color accuracy? If so, how do I check if my monitor meets the specification?
Dell calibrates the U2410/U2711 according to the DeltaE(1931) standard using equipment that can accurately measure high color gamut panels.
4.         Will Dell guarantee all replacement units are also color calibrated?
The color calibration is only done for new units shipped from factory; thus, replacement units will not be color-calibrated.
5.         In the event of warranty exchange, will the replacement unit come with a similar Color Calibration report?
Dell does not do the color calibration on the replacement units, as such, there will not be a Color Calibration Factory Report or similar attached to replacement units.
In cases where a brand new unit from factory needs to be shipped as a replacement unit, a Color Calibrated Factory Report will be shipped with it.
6.         Why does Dell only provide the Color Calibration Factory Report for new factory units of U2410/U2711?
The color calibration is done at factory to ensure color is accurate for each unit of U2410/U2711 when it reaches the customer.
7.         Is it possible to revert to factory pre-tuned settings after I color calibrated my unit with my equipment?
The customer should not re-calibrate and save your result in sRGB and AdobeRGB preset modes. Once overwritten, it is not possible to revert back to factory pre-tuned setting. The customer is advised to use the "Custom Color" preset mode to do their own calibrations.
8.         How do I use this Color Calibration Factory Report?
The Color Calibration Factory Report is provided for customer’s reference that Dell does color-calibration on the U2410/U2711 to ensure color accuracy and consistency for each unit of U2410/U2711 shipped.
9.         My own measurements of sRGB, gamma or AdobeRGB are not meeting the values stated in the report. Why is this so and can I get an exchange?
One of the reasons could be the different type of color calibration equipment used. There are many types of color calibration equipment in the market.
Dell ensures Color Accuracy based on the Dell approved Color-Calibration equipment at Dell’s factory.

Bluetooth Driver for dell(Inspiron N5110(ST: 3v82np1 ) is still not working well.

Hi,
I have tried installing "Dell Wireless 1701
802.11 b/g/n, Bluetooth v3.0+HS Driver "
But I saw neither wireless nor Bluetooth was defined.
As the drivers listed below are only the driver for wireless and bluetooth, I almost tried all of them, except the last three.
File TitleImportanceRelease DateVersionActions
Intel Centrino Wireless-N 1030 WiFi Driver
(Driver)
Other Formats
Description
Intel 6230/N1030/N1000 WiFi Driver for win7 64-bit This package provides the driver for the Intel Centrino Wireless-N 1030 WiFi Driver and imore…
Intel Centrino Wireless-N 1030/Advanced-N 6230
Bluetooth Adapter Driver
(Driver)
Description
This package provides the Intel Centrino Wireless-N 1030/Advanced-N 6230 Bluetooth Adapter Driver and is supported on Inspiron N5110 and Vosmore…
Dell Wireless 1701 802.11 b/g/n, Bluetooth v3.0+HS
Driver
(Driver)
Description
This package provides the Dell Wireless 1701 802.11 b/g/n, Bluetooth v3.0+HS Driver and is supported on Inspiron N5110 and Vostro Notebook 3more…
Dell Wireless 1702 WiFi + Bluetooth Driver
(Driver)
s
Description
This package provides the Dell Wireless 1702 802.11 b/g/n, Bluetooth 3.0+HS Driver and is supported on Inspiron and Vostro Notebook models tmore…
Intel Centrino Wireless-N 1000, Centrino Advanced-N
6230, Centrino Wireless-N 1030, v.14.2.0.10, A01
(Driver)
Recommended
Description
This package provides the Intel Centrino Wireless-N 1000/1030, Advanced-N 6230 Driver and is supported on Inspiron N5110 and Vostro Notebook more…
Intel Centrino Advanced-N 6230/Wireless-N 1030
Bluetooth Adapter Driver
(Driver)
Description
This package provides the Intel Centrino Advanced-N 6230/Wireless-N 1030 Bluetooth Adapter Driver and is supported on Inspiron N5110 and Vosmore…
Add to My Download List
Dell Wireless WLAN 1502 Half Mini-Card Driver
(Driver)
Description
This package provides the driver for Dell Wireless WLAN 1502 Half Mini-Card and is supported on Inspiron Notebook and Vostro Notebook modelmore
Intel WiMax Link 6150 Driver
(Driver)
Description
This package provides the Intel WiMax Link 6150 Driver and is supported on Inspirion and XPS Notebook models that are running the following
Realtek RTL8111E-VB Gigabit and RTL8105E-VB 10/100
Ethernet Controller Driver
(Driver)
Description
This package provides the Realtek RTL8111E-VB Gigabit and RTL8105E-VB 10/100 Ethernet Controller Driver and is supported on Inspiron N5110 amore…
I had to install Dell Wireless 1702 WiFi +
Bluetooth Driver
The wireless adapter was defined by this driver, however, the Bluetooth still has an exclamation mark in front of it, and when the Dell WLAN and Bluetooth client installation finished, a pop up message said that Windows couldn't install the device
well, although there was a folder added in documents folder named 'Bluetooth Folder'
Yes, the Bluetooth was named with 'Generic Bluetooth adapter' before installing 'Driver above'. However, after installing the driver above, the Bluetooth adapter named with ' Dell wireless 1702 Bluetooth v3.0". But as you see it's
still not working will.
The sceen shot shows the device manger before installing Dell
Wireless 1702 WiFi + Bluetooth Driver
These screen shots shows the device manger after installing Dell
Wireless 1702 WiFi + Bluetooth Driver
I've lit windows detect the operating program for this device on the internet, it said "Windows has detected that the operating program of this device is up to date. As this screenshot shows.
What should I do because nothing lift to try? If you have a look at the ninth drivers in my previous message, you will see that no other drivers for Bluetooth lift.
Also, I have tried to install Intel
Centrino Wireless-N 1030 WiFi Driver
But I have been told that "the installation is blocked', This package of installation cannot be installed on your system' I don't know what this
means, is it because Dell Wireless 1702 WiFi +
Bluetooth Driver is being installed
Could you please take some of your preciout time out to read carefully my points below to finish this problem?
first:
Yes, if you had a look at my first post, you would have seen that I really have downloaded and installed the drivers suitable for bluetooth, which was only Dell
Wireless 1702 WiFi + Bluetooth Driver, which made the bluetooth recognized by Windows 7(64Bit). However, the bluetooth in the device manager still has an exclamation mark as it is shown in the device manager.
I don't have any other drviers which can do more than the what Dell
Wireless 1702 WiFi + Bluetooth Driver did because I have tried all the drivers listed under 'Network', exept the what are for Etherent.
Yes, when I have tried adding the bluetooth between two laptops(Mohammad and Nasreen). the bluetooth was added for both laptops as you see in these screenshots below:
The Bluetooth devices of Nasreen's laptop whose bluetooth is having some problems in Device mangage.
The Bluetooth devices of Mohammad's laptop whosse Bluetooh is defined well in device manager.
But there is still problem in the device managre as shown in the screenshot listed before.
Second: (Important) That when I want to send files or recieving between two bluetooth added in either laptop, I could send them. Also, when I open the Mohammad's bluetooth added in Nansreen's laptop( screenshot
below), I can show what is inside it.
However, when I open the the Nasreen's bluetooth addd in Mohammad's laptop, I noticed no reponse at all because as you see that disconnected is written in fornt "Nasreen-Pc" as this screenshot:
Although sometimes Nasreen-Pc gets connected as screenshot below, but I am still not able to open the Bluetooth folder of Nasreen-pc from Mohammad-pc. When trying to do that, no response is there.
In other times, Nasreen-pc gets connected for a while, but it comes back disconnected.
Third:: I noticed that the name of Laptop whose Bluetooth was added listed in 'My computer' for the laptop whose Bluetooth is having some problems in the device manager.(First Screen shot below) However,
the name of the laptop whose Bluetooth is having problems wasn't listed on other laptop's "my computer"(Second Screen shot below)
Finally: : when I clicked "right-click" on "Nasreen-PC" and then clicking on "detecting and troublshooting issues", I found that windows informed me that :
But which driver should I reinstall because I have already installed the Dell
Wireless 1702 WiFi + Bluetooth Driver almost twice?
A man should convert his anger and sadness into strength to continue living in this life.

Certain driver packages contain drivers from some of the essential services only and for additional services, separate drivers must be installed. Additionally, the service is installed only if a compatible device is installed (or paired).
Therefore, you are seeing the error.
If you are using the Bluetooth L2CAP Interface and Bluetooth Remote Control services and not able to install the services, you can try unpairing the device, restart the PC, pair the device and then check. If that too fails, you need to install a suitable
driver, sometimes even other OEM drivers solve the issue. You can Bing/Google about this. You can also contact Dell Support for more information.
Balaji Kundalam
Thanks a lot,
I really didn't understand what you mean with in your first part the service is installed only if a compatible device is installed (or paired).
The Bluetooth is integrated with
the laptop, then where other services will come from, all service are related to Bluetooth.
If there are some additional services not related to Bluetooth,
then how can I either let them functioning well or disable them in order to get rid of the yellow exclamation mark
on the name of my laptop in the Device and printers.
Also, I really have installed a
BCBT7(Broadcom Bluetooth) for HP which really defined the same Bluetooth issue,
Device manager after installing the entire setup of driver BCBT7(Broadcom Bluetooth) on HP laptop
but when trying to install the same
BCBT7(Broadcom Bluetooth) on Dell, I faced the error below, although there is an icon for Bluetooth in
the system tray. Also, the Bluetooth is integrated as
you have seen in the device manager.
You didn't answer me: Third:: I noticed that the name of Laptop whose Bluetooth was added listed in 'My computer' for the laptop whose
Bluetooth is having some problems in the device manager.(First Screen shot below) However, the name of the laptop whose Bluetooth is having problems wasn't listed on other laptop's "my computer"(Second Screen shot below)
A man should convert his anger and sadness into strength to continue living in this life.

Lenovo ThinkPad X1 and Dell U2711 / HDMI?

Hello,
I plan to purchase the Dell U2711 monitor, it has a resolution of 2560 x 1440.
Will my Lenovo ThinkPad X1 handle this over the HDMI port?
Thanks in advance,
Simon

Not thru HDMI, but it will thru the mini-display port. You simply need a mini-display port to full size display port cable, something like this.
http://estore.circuitassembly.com/products/Mini-Displayport-to-Displayport-Adapter-Cable.html
| X220 i7-2620M | 12.5" IPS | Intel 520 Series 180GB Main SSD | Mushkin 120GB mSATA SSD | 8GB RAM | Intel 6205 WiFi | BT | Win7 Pro 64 SP1 |

Considering a Dell U2711 for MacMini Server

Hi All,
I am planning to buy a MacMini Server to go with my Dell U2711 Display.
I am a bit confused regarding the means of connecting the Display to MacMini for running at 2560 x 1440 resolution.
Apple tells on MacMini specifications page, that output through HDMI is limited to 1920-by-1200.
That said, I am left with the "Thunderbolt" way to achive the native resolution of 2560 x 1440, right?
So, what cable should I use to connect the display through thunderbolt port?
Some articles suggest using the so called "Mini DisplayPort to Dual Link DVI" Cable to do that, but then isn't is a misleading naming for a thunderbolt cable?
I would expect something like a "Thunderbolt to Dual Link DVI" cable.
Thanks!

Iam buying this model, have tou tried 1080p videos external monitors anf full hd flash videos from vimeo?
please let me know
siaco wrote:
Just though I should fill in a bit here, as I have now bought this laptop and running Arch 64bit on it. So if any other users are considering this laptop, here are a few lines about it:
I have it up and running with LUKS disk encryption, everything works fine so far. I'm running XFCE with just a minor problem that the bottom panel is kinda blinking 3 or 4 times right after boot. Havn't tested webcam nor bluetooth, but sound and everything else seems to work fine.
Two of my biggest problems were to get the wifi up and running and to get an acceptable performance when viewing videos in full screen. As for the wifi; just me not understanding that I needed a kernel module AND a firmware.. (If someone wants to fill me in on why we need a firmware AND a kernel module/ driver, I'd be glad.) I installed the iwlwifi-5000-ucode without knowing I also needed the iwlagn module too. After that was fixed, I am now using network manager with no problems.
I have also had some problem with the Radeon 3670. The performance was bad in full screen videos when I used the xf86-video-radeonhd. (I followed arch wiki). It didn't help to use vide-ati neither, and no settings in the xorg.conf did fix my problem. I also noticed that DRI was failing in xorg.log. After alot of trying I decided to try the git-versions which are found in the AUR. I'm happy to say that I can now watch 720 (the only video resolution I have tried yet) with acceptable quality
All in all, I'm quite happy with the computer so far. A bit warm maybe. Oh, and the screen (full HD version) is SOO nice :-)

Dell U2711 black screen when connected to Mac via DisplayPort

I currently have a Dell U2711 27" monitor connected to my Mac Mini through DVI (it uses a DVI to mini-DVI adapter at the PC end). However, I cannot get the full resolution of the monitor 1920 x 1080 maximum is offered were the monitors maximum resolution is 2560 x 1440.
I did some Googling and seemed it required DisplayPort connection to achieve this. No dramas. I ordered a Mini-DisplayPort to DisplayPort cable.
I plugged this in and all I get on the Dell is a black screen. The monitor doesn't go into power save mode or anything like that, just displays nothing - an illuminated black screen.
I pulled out my MacBook and connected the cable to that, same deal. The Mac recognises that the cable has been connected (as the laptops LCD goes blue for a second or two while it detects the new monitor).
Any ideas?
I also had a DisplayPort to DisplayPort cable here which was included with the monitor from Dell, which I will test aswell when my miniDisplayPort to DisplayPort adapter arrived.

Yes, that is one means, but...
However, HDMI 1.3 can also carry resolutions higher than 1920 x 1080 - check out http://en.wikipedia.org/wiki/HDMI - not really an option on the Dell monitor though, as it only supports up to 1080p on the HDMI connection. However, there is a thread elsewhere on the internet of a user who forced his Windows laptop to use 2560 x 1440 resolution via the HDMI output and the Dell monitor accepted it!
In addition, so can DisplayPort - as per my original post.
The Apple Dual-Link DVI adapter is plagued with issues and has a lot of faults, so I'd rather avoid it. It is also significantly higher priced than the above option of DP.

External Monitor (Dell u2711) problems

Hi all,
I'm an editor and just bought a Dell u2711 to hook up to my MacBook Pro (2.53 GHz, 4GB Ram, NVIDIA GeForce 9400M). The DVI would only support up to 1920x1280 so I bought a mini DisplayPort to DisplayPort adapter and that got me up to my full resolution for the monitor.
HOWEVER... my computer seems to be too slow or the graphics card isn't good enough to support such a monitor. Is this true? When I use the external monitor as extra desk space and put all my FCP windows in it I get this banding on my subjects when they move. It just looks like very slight glitches and the movement isn't displayed so smoothly. I'm working with 1080p ProRes 422.
When I try and use the Dell u2711 as an external video monitor (display all frames) it lags pretty bad and the motion is stuttery and not showing in smooth motion.
Please help. Would I have been better off with the 27" Cinema display? I thought they were pretty similar monitors. Is my laptop or graphics card not up to the task? Just last Nov. or so I got this laptop with what I thought was the best available graphics card Apple had at the time for this laptop.

Go to your Audio / Video Settings >> A/V Devices tab and turn of "Mirror on desktop" for Playback ... this will reduce the load on your system as it will not be trying to decode the video for two separate (and different) playback streams simultaneously ie when using Digital Cinema Desktop Preview to display All Frames then you will not see playback in the Canvas window as well, just on the external preview monitor.
And/Or you could also try setting FCP's System Preferences >> Playback Control >> Gamma Correction to "Approximate" ... according to the manual this can offer a little performance boost (but to be honest I haven't ever tested this).
Choosing Real-Time Playback Gamma Correction Options
Whenever you watch your video on a computer display (such as video displayed in the Canvas, the Viewer, or via Digital Cinema Desktop Preview), Final Cut Pro applies gamma correction to the video to more closely approximate the way it would appear on a video monitor.
Note: Gamma correction is not applied to external video outputs such as DV or third-party interfaces because this correction is inherently applied by external video monitors.
If your computer’s graphics card supports gamma correction, Final Cut Pro automatically uses the card for accurate gamma correction. If your computer has an older graphics card that does not support gamma correction, you have two gamma correction options in the Playback Control tab of the System Settings window.
Accurate: High-quality gamma correction. This option is the most accurate but also requires the most processing power.
Approximate: Lower-quality gamma correction. This option leaves more processing power available for real-time effects but results in less accurate color and brightness rendition.
Tip: If your real-time performance is limited, try changing the gamma correction setting to Approximate (if available).
Hope it helps
Andy

Problem with Dell U2711

Hi there
I just took delivery of a new Dell 27" monitor and there's something wrong with the image at 2560x1440
I have it connected to my ATI Radeon HD 3870 Graphics card via a DVI cable
The image is all pixelated
Can anyone help?
Dell support is useless and keep asking me for a number that is not on the monitor
Thanks
Rob

Robert. I am in the process of procuring my first iMac. Stron preference toward the 27" iMac as it has teh dual Thunderboly ports. I already have 2 Dell U2711 monitors which I will connect to my iMac to give me a 3 screen setup, but the show stopper is the resolution being limited on the Dell U2711's. Did you manage to solve the resolution limitation with the screens being limited to 1920x1080 or did you manage to get them to run at 2560x1440?

Can X1900XT power Dell U2711 resolution

I'm thinking of getting the new Dell U2711 LCD monitor. Will my old X1900XT be able to run the 2560x1440 resolution?
Someone says it requires a dual-link DVI-D compatible graphics card here:
http://en.community.dell.com/forums/t/19319486.aspx
I read the X1900XT page it says it has Dual-link DVI, but not Dual-link DVI-D. Does that make a difference?
Here's the Dell U2711 specification page:
http://accessories.us.dell.com/sna/products/Monitors/productdetail.aspx?c=us&l=e n&s=bsd&cs=04&sku=224-8284
Here's the X1900XT specification page:
http://ati.amd.com/products/radeonx1900/radeonx1900xt/specs.html

The ATI 1900 has two dual-link DVI-I ports. These ports have both analog and digital video, so can be used for any display using DVI-A, DVI-D, or DVI-I plugs, single-link or dual-link.

Will the X1 drive multiple monitors?

I currently have a 2-monitor setup (Dell 30" monitor that requires dual-link DVI, and Dell 24" monitor that requires single-link DVI).
I realize that I'd need to get HDMI-to-DVI and mini-DP to DVI adapters, but if I did so, would the X1 drive the two monitors simultaneously?
As another way of asking, does the X1 drive monitors hooked to the mini-DP and the HDMI ports simultaneously?
Thanks for any help!

you can drive the Dell 30 inch using the mini DP port (you would need couple of adapters) and the 24 inch using the HDMI port simultaneously.
But the internal LCD will be switched off.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

TS3354 I have an Nvidia GTX 580 and a Dell U2711, which has HDCP support. Why do I get the message in itunes that my hardware does not support it?

I have an Nvidia GTX 580 and a Dell U2711, which has HDCP support. Why do I get the message in itunes that my hardware does not support it?
I downloaded 1080p content, not sure why this would not work with the hardware I have.
Bryan

Updated first post with dmesg output. I added all of it, but here's a quick snippet of the tail (which is right after booting up and attempting to autostart SLiM)
[ 13.426857] NVRM: API mismatch: the client has the version 310.19, but
NVRM: this kernel module has the version 304.60. Please
NVRM: make sure that this kernel module and all NVIDIA driver
NVRM: components have the same version.
Why is the kernel getting 304.60 ? That's got to be the issue, but I don't why the kernel is getting 304.60 ...
Output of pacman -Qs nvidia:
local/conky-nvidia 1.9.0-2
An advanced, highly configurable system monitor for X based on torsmo
local/lib32-nvidia-utils 310.19-1
NVIDIA drivers utilities and libraries. (32-bit)
local/libvdpau-git-flashpatch 20120825-1
Nvidia VDPAU library from git with patch to fix flash blue tint and bleed through
local/libxnvctrl 304.51-1
NVIDIA X Ctrl library
local/nvidia 310.19-2
NVIDIA drivers for linux.
local/nvidia-utils 310.19-1
NVIDIA drivers utilities and libraries.

Problems with MBP late 2009 + Dell U2711 + DVI Dual-Link

Hi!
I'm new to Apple Communities. I've been using for quite a long time my MBP with my Dell U2711 monitor. Sometimes it works perfect. But other times, just after bootup or reasume the display doesn't work properly.
Some times it doesn't detect the signal of the MBP and doesn't start.
Other times it displays the right image but with something like "noise" in every color.
The only solution I found is to turn off and on the display or if it doesn't start, forcing it touching the menu button to start up. If it appears noise and I just change the source and put it back again it works fine.
It has only happened me with this computer. I have also used it with a custom made computer with a GTX280 and never had a problem with it.
I tried to boot up with the 2 different graphics cards my MBP has, and with both I have the problem. I even had the problem using the "normal" DVI adapter. I suppose it must be something of the computer firmware. Some times, if I restart the computer using only the U2711 display. The bootup logo and loading is displayed fine. But when it displays the login window the noise starts.
I've always had this problem. It isn't something that started happening one day. I even reinstalled Mac OS X.
I'ts really strange and I found nobody who has the same problem. I hope someone has a solution.
If someone doesn't understand what I call "noise", please, tell me and I will post a photo of it.
Thanks in advance (and sorry for my English)

Double posting. Everyone, ignore this here and follow that one instead.

Is it posible to connect dell u2711 with display port to thunderbolt display.

I want to buy a macbook pro 15 2011 and thunderbolt display.
But I got a dell u2711 and I want to use this screen.
my question. Can I connect macbook pro to thunderbolt to dell u2711. for dual 27 screen

Yes, you can.
I have a similar configuration : same monitor but my macbook pro is late 2013. use a displayport cable for best results. you will be able to get 2560 x 1440 resolution.

WIll my MP drive a dell U2711

Similar Messages

Maybe you are looking for