Will not boot any harddrive

hi all,
i just installed an 80gb harddrive into my ibook, i installed OS x 10.5.1, and the installation was successful. but when it reboot afterword, it just sits at the gray apple and the wheel spins forever. same thing happened when using my old harddrive with 10.5.8 (Via firewire). the computer does however boot the install DVD for tiger and leopard. but i cannot get any HDD to boot. i also tried using safeboot while holding down shift..
i am stumped, this has never happened before.

i reinstalled leopard and it seems to be fine now.

Similar Messages

  • Phone will not boot, any hope to Recover Data?

    Is there a way to get data off a phone that will not boot up?
    My phone is constant rebooting. It reboots over and over and hangs on the eyeball screen, never getting to the home screen. (I plan to do a Factory Reset.)
    I hadn't done a back up recently, and had been saving photos on the phone memory rather than the SD card (lesson learned.)
    Is there any way to recover any of the data before doing a Factory Reset?
    I am aware of the "Volume Down, Power button" start up to do the reset - is there anything there that will allow it to be connected to the computer to copy files off?
    ... By the way, I have started the phone using Volume Down / Power start up and selected "Recovery" and I get the icon of a phone with a red triangle with an "!" inside it, but my computer does not recognize the phone when it is plugged in via USB.
    Thanks.

    I regret to hear that Safe mode is not working correctly. Below I have provided the instruction just in case.
    Safe mode
    http://support.vzw.com/clc/devices/knowledge_base.html?id=31062
    If the device will not go into Safe mode, I would agree with Budone and complete a hard reset
    Hard reset
    http://support.vzw.com/clc/devices/knowledge_base.html?id=30946

  • I have a MacBook Pro 15" and my warranty just ran out! I partitioned my harddrive into two partitions, one with Snow Leopard and the other with microsoft.This morning I turned on my Macbook Pro and it will not boot into Snow Leopard.

    Good Morning,
    I have a MacBook Pro 15" and my warranty just ran out! I partitioned my harddrive into two partitions, one with Snow Leopard and the other with microsoft.This morning I turned on my Macbook Pro and it will not boot into Snow Leopard. I shut it off took out the battery, reinstalled the battery. Then I put in the Snow Leopard CD and booted up to disk utility and The Snow Leopard partion would not show up?? I do see the microsoft partion.
    I also rebooted holding down the shift key and still no Snow Leopard
    Could you please tell me what I can do, what keys do I press on restart any advice to get Snow leopard back.
    thank you.

    Have you restarted holding down the Opt key?  That procedure should give you a gray screen with all of the partitions that exist.  Then select the SL partition for boot.  Also go to System Preferences and Startup Disk, unlock the lock and select the SL partition as the default boot partition, then relock.

  • Power mac g5 will not boot to dvd at all any ideas?

    Power mac g5 2.3 late 2005. Leopard 10.5 installed on drive and boots ok to hhd.
    how ever i need to go back to tiger 10.4.4 or later for my music hardware to work correctly..
    Sooo i purchased a Tiger 10.4 black retail disk and it will not boot to it in any way all I end up with is a kernal report screen.
    I have tried everything.. taking the drive out. adding a new formatted drive to install to.. no joy..just does not even look to be installing nothing..not even a spinning wheel thingy . if the disk was too early eg before late 2005 would it act like that and not install?
    I'm lost here lol.

    Hmmm, something else is going on I guess...
    The dvd is black with the X on it and has this number on it - 2Z691-5305-A
    Apple Mac OS X 10.4 Tiger (Full Install) DVD Retail Version
    Item #:
    MA453Z/A 1005166
    Compatible with eMac (2005), iBook G4 (Late 2004), iBook G4 (Mid 2005), iMac G5 17-inch (ALS), iMac G5 20-inch (ALS), iMac G5 (17-inch iSight), iMac G5 (20-inch iSight), iMac (Early 2006 17-inch), iMac (Early 2006 20-inch), Mac mini, Mac mini (Late 2005), Mac mini (Early 2006), MacBook Pro, Power Mac G5 (Early 2005), Power Mac G5 (Late 2005), PowerBook G4 (15-inch Double-Layer SD), PowerBook G4 (17-inch Double-Layer SD).
    Also...
    Mac OS X Tiger 10.4 Drop-in Install Hardware Bundle (CDVersion)
    Item #:
    2Z691-5306-A 1002481
    Compatible with eMac (2005), iBook G4 (Late 2004), iBook G4 (Mid 2005), iMac G5 17-inch (ALS), iMac G5 20-inch (ALS), iMac G5 (17-inch iSight), iMac G5 (20-inch iSight), iMac (Early 2006 17-inch), iMac (Early 2006 20-inch), Mac mini, Mac mini (Late 2005), Mac mini (Early 2006), MacBook Pro, Power Mac G5 (Early 2005), Power Mac G5 (Late 2005), PowerBook G4 (15-inch
    MA453Z/A 
Disc 1 - 2Z691-5306-A 
Disc 2 - 2Z691-5307-A 
Disc 3 - 2Z691-5308-A 
Disc 4 - 2Z691-5420-A 
Disc 5 - 691-5145-A, Ver 2.0 

The iwork cd is 603-6242.
    http://www.welovemacs.com/2z6915306a.html

  • My father's iphone will not boot. We live in Barbados but the phone was bought in the US. Is there any way to fix this, or does he need a new phone, and is this covered by warranty?

    My father has owned his iphone for almost exactly 9 months. The phone was purchased in the US when he was on holiday. We live in Barbados, but the phone should still be under warranty. (please correct me if I'm wrong). He says the phone will not boot, it is inconsistent with showing how much battery life it has and it keeps looping because it's always trying to reboot. He treats his electronics very well and the phone is in perfect condition. Is there any way that this can be fixed without him losing all the information on the phone? Or can he get a replacement phone (due to the warranty issue)?

    Have you tried any basic troubleshooting
    restart
    reset
    Restore
    See user guide
    http://manuals.info.apple.com/en_US/iphone_ios5_user_guide.pdf
    assuming iPhone is still using iOS 5.0.1

  • G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD

    We have a DP 1ghz Quicksilver PowerMac G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD that came with the machine.
    We were in the process of installing 10.4 Tiger before placing it for sale.
    The Mac was originally OSX Server 10.1 that we later converted to a worksation running 10.3 Panther.
    It has 1 GB of memory, 80GB hardrive, 250MB Zip Drive and a Radeon 7500 video card.
    Since this machine only has a CD-R drive and not a DVD-R, we installed Tiger using another Mac via Target Disk Mode. The installation process went well, but when I tried to reboot I got a Kernel Panic right after startup screen with the grey Apple logo.
    On some reboots we get to the blue startup screen, others it stops at the grey Apple logo, others a black box like the a Kernel Panic - but with no text. Twice it went directly into Open Firmware.
    We have done the following during our troubleshooting:
    - Reseat RAM, Video Card, Hard Drive, Zip & CD-R connections
    - Remove RAM 1 stick at a time and reboot
    - Replace RAM with RAM from another working Quicksilver
    - Replace Video Card with one from another working Quicksilver
    - Zap PRAM
    - Reset CUDA switch
    - Unplug the MAC and remove everything (RAM, Battery, etc) for 30 minutes and try to reboot
    - Tried booting from the Macintosh Server G4 Software Restore CD
    - Tried booting from Mac OS X Server CD
    - Tried booting from AppleCare Protection Plan CD with TechTool
    - Tried booting from Diskwarrior CD
    - Tried booting from an external FireWire drive with a disk image of Tiger OS Install
    - Tried booting with the hard drive disconnected
    The Mac WILL boot from the Apple Hardware Test CD and will pass ALL of the extended tests.

    Conventional wisdom says that any Mac that will not boot up from a System/Install CD OS 9 or an Install CD Mac OS X, has a Hardware problem.
    The diagnostic CD is a red herring because it uses a very primitive method of reading the CD, and so does not properly represent the machines general ability to read CDs.
    I would look at the CD drive cables, etc, and see if another drive gives different results.
    You have not mentioned using the Startup Manager (option key at Startup) to do any checking:
    HT1310- Startup Manager: How to select a startup volume

  • IMac will not boot from any mode except Target Disk

    I have an Early 2008 Penryn iMac 24" MB398LL/A running OS X 10.7.4 (see specs below) that will not boot from ANY mode, It also has several strange vertical bars from top to bottom on the screen. They are about 10 px wide, with some pixels empty and looks a bit like a barcode if you squint at it.
    I have tried Safe Boot, Force Boot, DVD Boot, FireWire/USB Boot,  and it always gets to the same point. It gets to the apple screen with the spinning gear and then after about 8 seconds it freezes. The only way it works at all is in Target Disk Mode. It pops right up on my Macbook Pro and I was able to grab all my info!
    I have run Disc Utilities and Tech Tool on it many times from my MBP and it passes every test.
    I reformatted the HD and installed 10.7 again, it still freezes up at the same point. 
    I have tried using Single User mode and every time have had to run /sbin/fsck -fy twice because it always says the disk is ok but it was modified on the first pass.
    I thought maybe it had a bad video card or logic board but and I ran the Apple Hardware Test on many occasions and it always passes. Recently I was told about Loop Mode and just completed running the AHT for just over 30 hours without any errors at all.
    UPDATE...
    Strange Part… I tried installing Mountain Lion in Target Disk Mode and everything went smoothly. When it restarted on its own the lines on the screen were gone for the moment, but the Mac still freezes up on the spinning gear and immediately restarts on its own.  I have run every thing listed above on it and still nothing. Sometimes the lines reappear then in two more starts they are gone.
    I did manage to have it start one time got a copy of the  the error report (its at the bottom too) The Mac ran for at least 30 minutes with no problems, then the screen went crazy a few seconds and it became unresponsive. The mouse moved but that was all it could do. Now my iMac continually restarts itself, I don't have any more ideas, HELP!
    Specs...
    The iMac "Core 2 Duo" 3.06 24-Inch Aluminum (Early 2008/Penryn) features a 3.06 GHz Intel "Core 2 Duo" processor (E8435), with two independent processor "cores" on a single silicon chip, a 6 MB shared level 2 cache, a 1066 MHz system bus, 2 GB of RAM (800 MHz DDR2 SDRAM, PC2-6400), a 500 GB (7200 RPM) Serial ATA hard drive, a vertically-mounted slot-loading DVD±R DL "SuperDrive", NVIDIA GeForce 8800 GS graphics acceleration with 512 MB of GDDR3 memory, a built-in iSight video camera, and built-in stereo speakers underneath the 24" glossy TFT Active Matrix LCD (1920x1200 native) display.
    Error Report…
    Sat Sep  1 17:13:12 2012
    panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
    CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
    RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
    RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
    R8:  0x0000000000000000, R9:  0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
    R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
    RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS:  0x0000000000000008, SS:  0x0000000000000010
    Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0

    Here is the complete error log...
    Sat Sep  1 17:13:12 2012
    panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
    CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
    RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
    RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
    R8:  0x0000000000000000, R9:  0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
    R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
    RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS:  0x0000000000000008, SS:  0x0000000000000010
    Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0
    Backtrace (CPU 0), Frame : Return Address
    0xffffff80602db800 : 0xffffff801a41d5f6
    0xffffff80602db870 : 0xffffff801a4b7b95
    0xffffff80602dba40 : 0xffffff801a4ce4ad
    0xffffff80602dba60 : 0xffffff7f9bab8654
    0xffffff80602dbb60 : 0xffffff7f9baa218c
    0xffffff80602dbbb0 : 0xffffff7f9baa20e2
    0xffffff80602dbbd0 : 0xffffff7f9ba73554
    0xffffff80602dbc00 : 0xffffff7f9aa8d470
    0xffffff80602dbc40 : 0xffffff7f9aa8d3df
    0xffffff80602dbc60 : 0xffffff7f9aa926ec
    0xffffff80602dbcf0 : 0xffffff7f9aa8af20
    0xffffff80602dbd20 : 0xffffff7f9aadacc7
    0xffffff80602dbd70 : 0xffffff801a833b9b
    0xffffff80602dbdc0 : 0xffffff801a862d57
    0xffffff80602dbe30 : 0xffffff801a497cef
    0xffffff80602dbe80 : 0xffffff801a420abd
    0xffffff80602dbeb0 : 0xffffff801a410448
    0xffffff80602dbf00 : 0xffffff801a4195fb
    0xffffff80602dbf70 : 0xffffff801a4a5ad6
    0xffffff80602dbfb0 : 0xffffff801a4ced13
          Kernel Extensions in backtrace:
             com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000->0xffffff7f9aab8fff
                dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
             com.apple.NVDAResman(8.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aad8 000->0xffffff7f9addafff
                dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
                dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
                dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
             com.apple.GeForce(8.0)[4B9BE287-5251-398E-96B0-BB16C9BFB2D9]@0xffffff7f9ba72000 ->0xffffff7f9bb34fff
                dependency: com.apple.NVDAResman(8.0.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aa d8000
                dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
                dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
                dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
    BSD process name corresponding to current thread: WindowServer
    Mac OS version:
    12B19
    Kernel version:
    Darwin Kernel Version 12.1.0: Tue Aug 14 13:29:55 PDT 2012; root:xnu-2050.9.2~1/RELEASE_X86_64
    Kernel UUID: 3005059E-270B-3B9F-940D-7A66C05DDC9D
    Kernel slide:     0x000000001a200000
    Kernel text base: 0xffffff801a400000
    System model name: iMac8,1 (Mac-F227BEC8)
    System uptime in nanoseconds: 26349024446
    last loaded kext at 22534854703: com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2 (addr 0xffffff7f9c489000, size 12288)
    loaded kexts:
    com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2
    com.apple.driver.AppleHDA          2.3.0f2
    com.apple.driver.AppleTyMCEDriver          1.0.2d2
    com.apple.filesystems.autofs          3.0
    com.apple.iokit.IOBluetoothSerialManager          4.0.9f8
    com.apple.iokit.IOBluetoothUSBDFU          4.0.9f8
    com.apple.driver.AppleLPC          1.6.0
    com.apple.driver.AppleMuxControl          3.2.6
    com.apple.driver.AppleBacklight          170.2.3
    com.apple.driver.AppleUpstreamUserClient          3.5.10
    com.apple.driver.AppleMCCSControl          1.0.33
    com.apple.GeForce          8.0.0
    com.apple.driver.AppleSMCPDRC          1.0.0
    com.apple.iokit.IOUserEthernet          1.0.0d1
    com.apple.Dont_Steal_Mac_OS_X          7.0.0
    com.apple.driver.ApplePolicyControl          3.2.6
    com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
    com.apple.driver.AppleIRController          320.15
    com.apple.iokit.SCSITaskUserClient          3.5.1
    com.apple.driver.AppleFileSystemDriver          3.0.1
    com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
    com.apple.BootCache          34
    com.apple.driver.XsanFilter          404
    com.apple.iokit.IOAHCIBlockStorage          2.2.1
    com.apple.driver.AppleFWOHCI          4.9.5
    com.apple.driver.AppleUSBHub          5.1.6
    com.apple.driver.AirPortBrcm43224          600.36.17
    com.apple.iokit.AppleYukon2          3.2.3b1
    com.apple.driver.AppleAHCIPort          2.4.0
    com.apple.driver.AppleIntelPIIXATA          2.5.1
    com.apple.driver.AppleUSBEHCI          5.1.5
    com.apple.driver.AppleUSBUHCI          5.1.5
    com.apple.driver.AppleEFINVRAM          1.6.1
    com.apple.driver.AppleRTC          1.5
    com.apple.driver.AppleHPET          1.7
    com.apple.driver.AppleACPIButtons          1.6
    com.apple.driver.AppleSMBIOS          1.9
    com.apple.driver.AppleACPIEC          1.6
    com.apple.driver.AppleAPIC          1.6
    com.apple.driver.AppleIntelCPUPowerManagementClient          196.0.0
    com.apple.nke.applicationfirewall          4.0.39
    com.apple.security.quarantine          2
    com.apple.driver.AppleIntelCPUPowerManagement          196.0.0
    com.apple.driver.DspFuncLib          2.3.0f2
    com.apple.iokit.IOAudioFamily          1.8.9fc9
    com.apple.kext.OSvKernDSPLib          1.6
    com.apple.kext.triggers          1.0
    com.apple.iokit.IOSerialFamily          10.0.6
    com.apple.driver.AppleSMBusPCI          1.0.10d0
    com.apple.driver.AppleBacklightExpert          1.0.4
    com.apple.driver.AppleSMBusController          1.0.10d0
    com.apple.nvidia.nv50hal          8.0.0
    com.apple.NVDAResman          8.0.0
    com.apple.iokit.IOFireWireIP          2.2.5
    com.apple.driver.AppleHDAController          2.3.0f2
    com.apple.iokit.IOHDAFamily          2.3.0f2
    com.apple.iokit.IOSurface          86.0.2
    com.apple.iokit.IOBluetoothFamily          4.0.9f8
    com.apple.driver.AppleGraphicsControl          3.2.6
    com.apple.iokit.IONDRVSupport          2.3.4
    com.apple.iokit.IOGraphicsFamily          2.3.4
    com.apple.driver.AppleSMC          3.1.3d11
    com.apple.driver.IOPlatformPluginLegacy          1.0.0
    com.apple.driver.IOPlatformPluginFamily          5.2.0d16
    com.apple.iokit.IOUSBHIDDriver          5.0.0
    com.apple.driver.AppleUSBMergeNub          5.1.5
    com.apple.driver.AppleUSBComposite          5.0.0
    com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.5.1
    com.apple.iokit.IOBDStorageFamily          1.7
    com.apple.iokit.IODVDStorageFamily          1.7.1
    com.apple.iokit.IOCDStorageFamily          1.7.1
    com.apple.iokit.IOATAPIProtocolTransport          3.5.0
    com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.1
    com.apple.iokit.IOFireWireFamily          4.5.5
    com.apple.iokit.IOUSBUserClient          5.0.0
    com.apple.iokit.IO80211Family          500.15
    com.apple.iokit.IONetworkingFamily          3.0
    com.apple.iokit.IOAHCIFamily          2.2.0
    com.apple.iokit.IOATAFamily          2.5.1
    com.apple.iokit.IOUSBFamily          5.1.6
    com.apple.driver.AppleEFIRuntime          1.6.1
    com.apple.iokit.IOHIDFamily          1.8.0
    com.apple.iokit.IOSMBusFamily          1.1
    com.apple.security.sandbox          220
    com.apple.kext.AppleMatch          1.0.0d1
    com.apple.security.TMSafetyNet          7
    com.apple.driver.DiskImages          344
    com.apple.iokit.IOStorageFamily          1.8
    com.apple.driver.AppleKeyStore          28.18
    com.apple.driver.AppleACPIPlatform          1.6
    com.apple.iokit.IOPCIFamily          2.7
    com.apple.iokit.IOACPIFamily          1.4
    com.apple.kec.corecrypto          1.0
    Model: iMac8,1, BootROM IM81.00C1.B00, 2 processors, Intel Core 2 Duo, 3.06 GHz, 2 GB, SMC 1.30f1
    Graphics: NVIDIA GeForce 8800 GS, NVIDIA GeForce 8800 GS, PCIe, 512 MB
    Memory Module: BANK 0/DIMM0, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
    Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
    AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.131.36.16)
    Bluetooth: Version 4.0.9f8 10405, 2 service, 18 devices, 1 incoming serial ports
    Serial ATA Device: WDC WD5000AAKS-40YGA1, 500.11 GB
    Parallel ATA Device: MATSHITADVD-R   UJ-875
    USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd400000 / 2
    USB Device: BRCM2046 Hub, 0x0a5c  (Broadcom Corp.), 0x4500, 0x1a100000 / 2
    USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x820f, 0x1a110000 / 5
    USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x5d100000 / 2
    USB Device: Hub in Apple Extended USB Keyboard, apple_vendor_id, 0x1002, 0x1d100000 / 2
    USB Device: Trackball, 0x046d  (Logitech Inc.), 0xc404, 0x1d120000 / 4
    USB Device: Apple Extended USB Keyboard, apple_vendor_id, 0x0204, 0x1d110000 / 3

  • Computer will not boot up correctly in any mode.

    Hello,
    I have a Compaq Presario CQ62 with Windows 7 that will not boot up to my log in screen and it does not matter what mode I put it in..safe..etc. I have tried everything I know to do ...like system recovery in the recovery manager. I have no recovery disk or anything. Any help

    That means the internal drive has failed, or there's some other hardware fault. What backups do you have?

  • IMac G5 will not boot and if it does, it does not display any logo

    Hi everyone, any assistance with this issue would be greatly appreciated. This is my godmothers iMac G5 that my family gave her a few years ago, it is the 2.0GHz model with no iSight camera but has the built in WiFi and Bluetooth.
    I went to start it today, after it being off for a week and a half and it will not boot. I start it up and it displays the solid white LED light on the front and revs its fans until I stop it. I got it to get past this once by resetting the SMU but all it did was make the Apple hardware test sound noise and get a blank white screen. No Apple logo or anything. Entire time it rev'd its fans.
    Thank you! If it is broken I will most likely sell it for parts and either buy her an older unibody MacBook or wait for the next-gen iPad with FaceTime and a buy a keyboard dock.

    HI and welcome to Apple Discussions...
    If you have the install disc that came with this G5, try checking the startup disk for errors.
    Insert your install disk and Restart, holding down the "C" key until grey Apple appears.
    Go to Installer menu and launch Disk Utility.
    (In Mac OS X 10.4 or later, you must select your language first from the installer menu)
    Select your HDD (manufacturer ID) in the left panel.
    Select First Aid in the Main panel.
    (Check S.M.A.R.T Status of HDD at the bottom of right panel. It should say: Verified)
    Click Repair Disk on the bottom right.
    If DU reports disk does not need repairs quit DU and restart.
    If DU reports errors Repair again and again until DU reports disk is repaired.
    When you are finished with DU, from the Menu Bar, select Utilities/Startup Manager.
    Select your start up disk and click Restart
    While you have the Disk Utility window open, look at the bottom of the window. Where you see Capacity and Available. Make sure there is always 10% to 15% free disk space
    If it won't boot from an install disc, try booting in Safe Mode Launch Disk Utility (Applications/Utilities). It's possible to do a live verification in Safe Mode to check the startup disk for errors, but not repair disk but at least you might get some insight as to the problem.
    Carolyn

  • My imac will not boot up, any answers?

    My imac will not boot up.
    It froze so I turned it off. Now it won't boot up at all.
    Any ideas

    Thanks for your help.
    i don't know how to do a hardware Test when it won't boot up.
    I tried to boot it from the original disc but it wouldn't recognise the hard drive at all
    Ditto from backup Hard drive.
    Any ideas??

  • HT201412 My iPad will not boot up, has a think logo running but will not start. Any ideas?

    My Ipad will not boot up, has a think logo running all the time...any ideas. Also had trouble upgrading to ios.6 the computer is not the original one I synved my ipas too. It started OK then failed. Now it will not connect at all to computer...comes up with an error.!!!

    Try DFU Mode Restore. Open iTunes on computer, connect iPhone to computer. Hold both Home and Power buttons for exactly 10 seconds, release Power button, keep holding Home button until iTunes recognizes iPhone in Recovery Mode. Usually about 20 seconds time. Restore iPhone Firmware.

  • HT3964 I have a MacBook Pro that will not boot up. The apple symbol   Read more: I have a MacBook Pro that will not boot up. The apple symbol is there and a spinning wheel continues to spin. Any options??

    I have a MacBook Pro that will not boot up. The apple symbol is there and the spinning wheel keeps spinning. Any idea how I can fix this?

    Reinstall OS X.
    Reinstalling Lion/Mountain Lion Without Erasing the Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
    OR
    Reinstall Snow Leopard without erasing the drive
    Do the following:
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.

  • Mac Pro will not boot from Leopard or any CD or DVD install disk

    My Mac Pro wont boot from my Leopard install DVD. It never gets by the gray screen, then after several minutes the screen scrolls down black and says I need to restart my computer. I tried my Tiger install disk and it still wont boot from that DVD. Held down the "C", used "option" and selected DVD and still no boot. I can boot from one HD that has Leopard 10.5.8, but another HD with Snow Leopard 10.6.3 will not boot. The HD with Snow Leopard shows up as "EFI Boot" not the name I gave that HD when I startup using the "option" key. Any help would be appreciated.

    At first I was just going to say it sounds like you have a bad optical drive, but then you had to go and say that it also won't boot from a HDD.
    That just makes things a whole lot worse.
    Start by removing the side cover and checking the RAM to see if any of the LEDs are lit up indicating bad RAM. Usually if there's any bad RAM found, it will just automatically disable that stick, but maybe yours isn't for some reason.
    Look for any other LEDs that may be lit. Generally speaking, the only time you should see an LED (outside of the power LED) lit consistently is if there's a problem.
    You should also see if you can get Apple Hardware Test to run, which may or may not find some problem.
    But sorry to say, it's sounding very suspiciously like a bad logic board.
    One other thing to try, is putting the SL drive into a different slot. So if you were putting it in slot 2, try slot 3 or 4. If you just have a bad SATA port, you might be able to just work around that until you get a new system.
    If by chance this system is still under warranty, do not walk, do not pass go, do not collect $200, RUN to the nearest AASP or Apple store to make it THEIR problem to sort out.

  • BIOS update, then will not boot from any drive

    This old laptop, 3000 C200 8922 was acting very clunky when on wireless.
    Downloaded Bios Version 63ET62WW and flashed it into the bios.
    Now, even though I can get to the bios screen, and it shows the hard drive, DVD/CD drive, it will NOT boot from either.
    It will also "see" a usb installed, but will not boot from it.
    I have removed all power and cleared the CMOS several times and I still have nothing. Tried two different hdd's which have been in the machine and same results. 
    HELP!! I should have never messed with it......

    hi k4pew,
    One rule after a BIOS update is to Load optimize deafults after updating.
       Try that go inside BIOS Hit F9 to load defaults then F10 to Save and Exit.
    If not
    Try turning on the computer and start hitting F1 to load the Recovery Menu and see if that will push then Try Reseting the PC.
    If still the same Im afraid that the BIOS needs to be reflashed.
    Im not aware of any flash tool or a your Previous BIOS Version Firmware available for download.
    You can try calling Lenovo Technical Support for any options available for repair.
    Im sorry to hear what happened
    Regards
    Solid Cruver
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • I have a mid-2010 27" Quad Core i5 iMac running 10.8.3.  Startup disk recognizes the primary hard drive as a startup volume but will not boot from it.  Have tried zapping PRAM, ran disk utility.  No errors reported  Any thoughts?

    I have a mid-2010 27" Quad Core i5 iMac running 10.8.3.  Startup disk recognizes the primary hard drive as a startup volume but will not boot from it.  Have tried zapping PRAM, ran disk utility.  No errors reported  Any thoughts?

    My bad Eric. The startup preference recognizes the primary as a 10.8.3 startup volume but when u select it the system does not boot. I can only boot from my external backup drive

Maybe you are looking for