Will not go beyond amber ATT greet screen

Battery, memory card, n sim card removed 2 manually reboot phone. Phone goes thru blackberry reboot mode that has a white progression bar (completes this mode), it proceeds to amber ATT greet screen and will not go beyond amber ATT greet screen. Stays at this screen until battery dies.

Lets try safe mode:
Battery pull, insert battery and when the red light goes off, hold down the back key through the entire boot process. It will give you a message about safe mode.
If you did install something, remove that app and do another battery pull.
http://btsc.webapps.blackberry.com/btsc/search.do?cmd=displayKC&docType=kc&externalId=KB17877
If something was installed / updated recently, then remove it and try another battery pull.
Only other option is to do a software reload:
http://supportforums.blackberry.com/t5/Device-software-for-BlackBerry/How-To-Reload-Your-Operating-S...
Please click the Thumbs Up icon if this comment has helped you!
If your issue is resolved, please click the solution button on the resolution!
Every BlackBerry should have BlackBerry Protect, get it now! | Follow me on Twitter | Bring Back BBM Music!

Similar Messages

Macbook pro will not advance beyond grey screen at beginning of boot

macbook pro will not advance beyond grey screen at beginning of boot

Try performing an SMC reset. I am having this problem also.
To perform an smc reset:
1. Shut down your Mac, leave the MagSafe charging in.
2. Push three buttons: shift + control + option and the power button. Push and release together.
3. Wait a few seconds then turn on your Mac as normal.
Hope that works out for you!

I have a CC Photography License and tried loading the new Lightroom cc but it will not open (only flashes the welcome screen for a split second) then goes blank. I tried uninstalling it, rebooting, etc. several times and it will not work on my Mac with Y

I have a CC Photography License and tried loading the new Lightroom cc but it will not open (only flashes the welcome screen for a split second) then goes blank. I tried uninstalling it, rebooting, etc. several times and it will not work on my Mac with Yosemite. Please help!

Check out this thread: Downloaded Lightroom CC but only get a quick flash of the startup screen then nothing, Lightroom 5 still working.

Pages 2.0 will not get past the "getting started" screen

i just updated pages to 2.0 on ipad 2 retina (ios 7.0.2) and now i cannot open pages, it will not get past the "getting started" screen
has anyone else experienced something similar?

Had the same problem. This sovled it for me:
Just let it load.
In Keynote, I didn't have so many documents, so the freeze didn't take too long- that's how I noticed it's just a freeze while loading.
For pages it took much longer. You can also turn off iCloud in settings for Pages, Keynote, etc. open it, re-enable iCloud in settings app again and quick switch back to pages (double-click home button). It will freeze up again, but after a while after all documents have been pulled from iCloud, it will be back to normal.

Will not boot up to log in screen

will not boot up to log in screen when powered up, all I get is a grey screen with apple logo in middle and spinning timer
I have tried resetting SMC
I have tried starting up in Safe Mode (it won't do that either)
I have gotten into disk utility to repair disk
I have tried resetting PRAM
nothing... we are on a network in a school district so my next step is to re-image it but wondering if there is something else I should try first
if not then how do I backup files that are needed before I re-image
thanks, Cindy

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
     a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

My 06' Macbook Pro crashed with vertical, green pixelated lines and now will not advance past the turn-on screen with the apple filled with green lines as well. Then, it says to hold down the power button to restart. Help?

My 06' Macbook Pro crashed with vertical, green pixelated lines and now will not advance past the turn-on screen with the apple filled with green lines as well. Then, it says to hold down the power button to restart. I have tried several times to get it past this point but tnothing helped.
I have an appointment at the Apple store today, but was wondering : will all of the information and files on my desktop be lost? Or is this a logic board problem?
Any help is much MUCH appricated.

I'm not sure, if you're out of warrenty it'll cost quite a bit for the replacement of the logic board replacement...unless you have apple care. you could ask apple to try and recover your hard drive but i'm not sure.

Angry Birds Friends on Facebook will not load in Firefox, just white screen. Will load using Chrome, etc?

Angry Birds Friends on Facebook will not load in Firefox, just white screen. Will load using Chrome, etc? Checked for malware, cleared cache, re-installed Firefox, disabled add ons, enabled java, updated flash and shockwave, etc.

Hello,
Try disabling graphics hardware acceleration. Since this feature was added to Firefox, it has gradually improved, but there still are a few glitches.
You might need to restart Firefox in order for this to take effect, so save all work first (e.g., mail you are composing, online documents you're editing, etc.).
Then perform these steps:
*Click the orange Firefox button at the top left, then select the "Options" button, or, if there is no Firefox button at the top, go to Tools > Options.
*In the Firefox options window click the ''Advanced'' tab, then select "General".
*In the settings list, you should find the ''Use hardware acceleration when available'' checkbox. Uncheck this checkbox.
*Now, restart Firefox and see if the problems persist.
Additionally, please check for updates for your graphics driver by following the steps mentioned in the following Knowledge base articles:
[[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]]
[[Upgrade your graphics drivers to use hardware acceleration and WebGL]]
Did this fix your problems? Please report back to us!
Thank you.

TS3694 I tried to download the ios updates yesterday morning and not my phone will not work. I get a screen the appears to instruct me t connect t I Tunes. When I do that I received a message telling me that i need to restore factory settings. when I try

I tried to download the ios updates and now my phone will not work. I receive a screen that instruct me to connect to itunes. When I connect to itunes, i am told that i must restore factory settings. When i attempt to restore factory settings, i receive an error message that an unknown error has occured (3194)

There's only one thing you can do: make an appointment with Apple genius at the Apple retail store for a out of warranty replacement.

Adobe reader will not install beyond stage 2, o

Adobe reader will not install beyond stage 2, on my vista computer.

Download the installer (10.1.4) from http://get.adobe.com/reader/enterprise/ then update it to 10.1.9.

Hello I have 2 seperate airport express systems on my network, each connecting to a stereo in a different room. suddenly, the one in the living room will not stop flashing amber, but the one in the bedroom works fine. I have already tried resetting it

Hello
I have 2 seperate airport express systems on my network, each connecting to a stereo in a different room. suddenly, the one in the living room will not stop flashing amber, but the one in the bedroom works fine. I have already tried resetting it with a pin, resetting it while plugging it in, and trying to find it in airport express setup (the setup assistant can't find it at all).
What am i doing wrong?

How do I configure the AX to connect to the hub's wireless network? It will only scan one base station Airport Express at a time in the Airport Utility. I think what I am trying to do is use the hub as a router to the two AX's. Is there a specific way to set this up?
To set up the AX to join a wireless network as a "Wireless Client," using the AirPort Utility, either connect to the AX's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, try these settings:
Launch the AirPort Utility.
Select the AX.
If not already connected to the AX's wireless network, go ahead and switch to it when prompted.
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <type in the network name/SSID of the wireless network that you want to join or select it from the pop-up menu>
Wireless Security: None OR, if you are using security on your wireless network:
Wireless Security: <Select the appropriate level of security for the existing wireless network: WPA/WPA2 Personal | WPA2 Personal>
Password: <enter your wireless network security password>
Verify Password: <re-enter the same security password>
Click Update to write the new settings to the AX.

Macbook pro will not wake up and shows black screen

Purchased a MBP three weeks ago. After putting the MBP to sleep it will not wake up. Shows black screen and makes fan sound but will not start unless power off and then on again and at times this does not work.

Hi a,
Try an SMC Reset: http://support.apple.com/kb/HT3964
If no luck, you have 90 days of free AppleCare phone support and a one year warranty. Contact AppleCare or make an appointment at an Apple Store "genius" bar.

HT204406 I attempted to download iTunes match w/o success. Step 1 was fine. Step 2 gets stalled and will not move beyond 80%... Any suggestions for a solution? Why is iTunes stalling on step 2?

I attempted to download iTunes match w/o success. Step 1 was fine. Step 2 gets stalled and will not move beyond 80%... Any suggestions for a solution? Why is iTunes stalling on step 2?

Hi folks,
I found a solution in case your MATCH is still buggy...
JUST BOOT YOUR MAC HOLDING THE SHIFT KEY (until you see a progress bar).
Then in itunes disable and re-enable iTunes Match.
It should rescan all your library and eventually works.
At the end just reboot your Mac normally.
Best regards from Paris.
Nico

Sign in to itunes store will not disappear and the whole IPad will not let me go into other screens till this pop up goes away. I have entered the password several times and still will not disappear. Turned the IPad on and off but the pop up remain

sign in to itunes store will not disappear and the whole IPad will not let me go into other screens till this pop up goes away. I have entered the password several times and still will not disappear. Turned the IPad on and off but the pop up remain

FIrst try a soft reset by holding down the home & sleep/wake buttons until the Apple logo appears then let go & let the iPad boot up normally.
If that doesn't help then to make sure you have a strong internet connection.
Try resetting Network Settings
Settings->General->Reset->Reset Network Settings,
You won't lose any data but will have to log back into your wifi networks.
Once logged back in and when the pop-up appears, try entering your password again.

HT2188 i have an ipad 1; software will not update beyond ios5.1.1

i have an Ipad 1, it will not update beyond ios5.1.1. How do I update to latest version of software?

It's not supposed to. That iPad isn't capable of running iOS 6 or 7.
(103286)

Tried to open an app and my iPad gen one froze. It only shows the apple on black screen and will show the operating wheel sometimes and while plugged in it will beep every few minutes. Will not load one show anything on screen but the small white apple.

Tried to open an app and my iPad gen one froze. It only shows the apple on black screen and will show the operating wheel sometimes and while plugged in it will beep every few minutes. Will not load one show anything on screen but the small white apple.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Will not go beyond amber ATT greet screen

Similar Messages

Maybe you are looking for