Will the 1tb and larger notebook drives work in my X60?

I am out of space on my hard disk and see now that notebook drives are available in 1tb and larger sizes. Someone told me that these drives, while still called 2.5" drives, are actually thicker than the 640gb and smaller notebook drives, and may not fit my computer.
Will one of the 1tb+ drives work in my X60?

you would need a 2.5 inch sata drive with 9.5 mm thickness, the max capacity you can get in that profile is 750 gigs. The 1 tb and anything larger are all 12.5 mm thick drive, and won't fit.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Similar Messages

Early 2009 Mac Pro - Will the 1tb Western Digital VelociRaptor (WD1000DHTZ) work?

I'm looking to upgrade my drive, but my Mac has 3G SATA and this drive says 6G. I'm confused as to wether or not it will work, but only at 3G speed. I'd prefer to get the 6G so when I upgrade my mac pro I can take the drive with me. Thanks.

SATA 3 (actually 3.1) 6G is a specification!
And like any SATA drive (spindle, not SSD) they can't saturate the controller chip's bandwidth (less than and shared by all four drives).
The drive is rated like the others in the new series for 200MB/sec, less than the 250MB/sec that each port theoretically gets.
So you only have to "worry" when talking about SSD with 6G - and there they have 8-12-16 channels and push (sustained I/O) up to 500-550MB/sec (max, not writes, rarely achieved except in benchmarks) and it is the I/O per sec and near zero seek latency that matters with those.
The 500GB $200 and is a nice compromise. $200 will also get you into a Crucial m4 256GB SSD.
What does matter is that the SATA 3.x specification improves on and has better cmmand queue feature and support, 64MB cache, dual (DSP) processors inside..
Same goes for any SATA like WD Black Caviar 1TB ($119).
There is no reason to be confused. And of course not everyone has motherboard with SATA3, and they are backward compatible.
For an SSD you can buy a 6G PCIe controller, even ones that have SSDs on them for 700MB/sec.
No one makes new drives that are not SATA 3.x compliant - that is the new standard.
there is also 250GB model $154 that makes a nice system drive, or throw 4 of those together to get 700MB/sec with 1.8TB storage.($620)

Will the fire wire western digital drive work on a new imac

I am now using 3 3 WD My Book Studio FireWire External Hard Drives on my older iMac. I am thinking of getting a new iMac and see that they do not have a firewire plug. Is there a way to use these drives with a new iMac?

bpf1947 wrote:
I am now using 3 3 WD My Book Studio FireWire External Hard Drives on my older iMac. I am thinking of getting a new iMac and see that they do not have a firewire plug. Is there a way to use these drives with a new iMac?
My configuration is:
>>> is a Thunderbolt cable connection
---> is a FW800 cable connection
Thunderbolt on iMac >>> Thunderbolt Drive 1 >>> Thunderbolt Drive 2 >>> Apple Thunderbolt to FW800 adapter ---> Nitro 8-Port FW800 Hub ---> 3 FW800 drives (I don't like chaining FW drives thus the hub).
The above configuration works like a champ. No problems at all.

Suddenly in the middle of editing a large project the cropping and other tools stopped working. Did i hit some key or something accidently?

suddenly in the middle of editing a large project in Aperture the cropping and others tools stopped working. Did I accidently hit something to do that?

Maybe you hit the "p" key?
Then "Quick Preview" will be turned on and prevent editing. Hit "p" again or use the "View" ->"Quick Preview" menu entry.

HT3529 I am currently deployed and was using my iMessage to be able to talk to family back in the states and my iMessage stopped working. It will no longer select my number to use as the send/receive. How do I fix this so I can continue to talk to family?

I am currently deployed and was using my iMessage to be able to talk to family back in the states and my iMessage stopped working. It will no longer select my number to use as the send/receive. How do I fix this so I can continue to talk to family?

Read here:
http://support.apple.com/kb/TS2755

Hi i want to send an ipad of a gift to a friend in italy, can it be done? will the wifi and 3g still work? also how does it work for a warrenty?

hi i want to send an ipad of a gift to a friend in italy, can it be done? will the wifi and 3g still work? also how does it work for a warrenty?

WiFi will work, cellular will work but they may not be able to access LTE, they will have to send it back to you for the warranty work.

Will the Power BI Analysis Services Connector work if AD and AAD UPN suffixes don't match?

We are using Azure Active Directory, AD FS, and DirSync with
Alternate Login IDs, which means that our on-prem usernames have a different UPN suffix from our AAD usernames.
Will the Power BI Analysis Services Connector work in this setup? Or do the AD and AAD UPN suffixes absolutely have to match?

Hey Adam,
From SSAS, we simply query AD by passing the UPN we receive from AAD. As long as AD can find a match, it'll work.
So if there is a way in AD to map a particular UPN to another value, it'll work.
For example: For a user A, her on premises UPN is
'[email protected]' but she uses '[email protected]' as her email address. From AAD we'll receive
'[email protected]' & since AD knows that this is same as
'[email protected]' effective user name will work.
Hope this clarifies! let me know if you have more questions.
-mini

I am using Numbers app for the ipad and it has been working absolutely fine but now, when I want to email a spreadsheet as a PDF via the 'share and print' option, the file now doesn't appear as an attachment to the recipient. Any ideas please?

I am using Numbers app for the ipad and it has been working absolutely fine but now, when I want to email a spreadsheet as a PDF via the 'share and print' option, the file now doesn't appear as an attachment to the recipient. Any ideas please?

Hi mafiose15,
Thanks for visiting Apple Support Communities.
Restoring your iPod to factory settings is the best way to try and get it back to working order. You can use the instructions below to restore it:
How to restore iPod
Verify that you have an active Internet connection, because you may need to download new versions of the iTunes and iPod Software.
Download and install the latest version of iTunes if necessary.
Open iTunes. Connect your iPod to your computer using the USB or FireWire cable that came with your iPod.
After a few moments, your iPod will appear in the Source panel in iTunes.
Select your iPod in the Source panel. You will see information about your iPod appear in the Summary tab of the main iTunes window.
Click Restore.
If you are using a Mac, you will be asked to enter an administrator’s name and password.
A progress bar will appear on the computer screen, indicating that stage one of the restore process has begun. When this stage is done, iTunes will present one of two messages with instructions specific to the iPod model you are restoring.
Disconnect iPod and connect it to iPod Power Adapter (typically applies to older iPod models).
Leave iPod connected to computer to complete restore (typically applies newer iPod models).
During stage two of the restore process, the iPod displays an Apple logo as well as a progress bar at the bottom of the display. It is critical that the iPod remain connected to the computer or iPod power adapter during this stage.
Note: The progress bar may be difficult to see, because the backlight on the iPod display may be off.
After stage two of the restore process is complete, the iTunes Setup Assistant window will appear. It will ask you to name your iPod and choose your syncing preferences, as it did when you connected your iPod for the first time.
You can find the instructions in this article:
Restoring iPod to factory settings
http://support.apple.com/kb/ht1339
All the best,
Jeremy

After updating to 8.1.2 my iPad continues to restart. I tried resetting all the settings and this didn't work. I tried rebooting by holding the start button & power button and it didnt work either. The problem has actually worsened. I can no longer u

After updating to 8.1.2 my iPad continues to restart. I tried resetting all the settings and this didn't work. I tried rebooting by holding the start button & power button and it didnt work either. The problem has actually worsened. I can no longer use my iPad.

You need to restore the iPad.
Use iTunes to restore your iOS device to factory settings - Apple Support
If that will not work, you will need to use Recovery Mode to restore.
If you can't update or restore your iPhone, iPad, or iPod touch - Apple Support

Will the lightning to 30 pin adapter work with the irig midi interface?

will the lightning to 30 pin adapter work with the irig midi interface? Want to record guitar with garage band on ipad mini. need quick/easy way to connect USB to ipad mini

From both? Interesting. I like that though. I am looking for the controls to be on the iPhone rather than the stereo as it ***** finding songs this way. And yeah, $39.00 is a lot for this, and it is only roughly 8" long. Oh well, I will need it, so I will have to buy it. Thanks for the message back!

Ipad displays "ipad is disabled connect to itunes", I have tried putting the ipad into recovery mode and then restoring but that does not work. I have also tried doing a hard reset of the ipad and that does not work either. Any ideas?

Ipad displays “ipad is disabled connect to itunes”, I have tried putting the ipad into recovery mode and then restoring but that does not work. I have also tried doing a hard reset of the ipad and that does not work either. Any ideas?
My son let one of his friends use his ipad. The next time he tired to use it he could not get it unlocked, I tired to unlock it but it kept telling me that I had the wrong pass code. With out me knowing my son continued to tire until it completely disabled it self.

How can I unlock my iPad if I forgot the passcode?
http://www.everymac.com/systems/apple/ipad/ipad-troubleshooting-repair-faq/ipad- how-to-unlock-open-forgot-code-passcode-password-login.html
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
You may have to do this several times.
Saw this solution on another post about an iPad in a school environment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just canceling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
 Cheers, Tom

My phone fell down on the floor and shutt off not working again

my phone fell down on the floor and shutt off not working again

what i should do to know the phone has damaged,
Try the steps here for the appropriate symptoms.
http://support.apple.com/kb/TS2802
If you are unable to get the iPhone working, it's almost certainly damaged. Take or send it to Apple for a definite diagnosis.
how much fees for replacement ??
If you have AppleCare+ coverage, the cost will low; in the US it's $49. If you do not have AppleCare+ on your iPhone, see the Service Pricing section here:
http://www.apple.com/support/iphone/service/faq/
Regards.

Will the new final cut pro x work with my Final cut pro version 6.0.6 data

will the new final cut pro x work with my Final cut pro version 6.0.6 data

Thanks Tom.
So I will need upgrade to FCP 7 first, then convert to an XML file in 6.0.6, then convert to another file that FCP X can read? I have a lot of half done projects that need finishing. Is this process very complex and time consuming?
Maybe I should be approaching this from a different angle. The reason I am asking is that I now need to upgrade to a new Mac book pro and have been told that I cant run final cut pro 6.0.6 on the new models using maverick. Is this true?
Roger

Will the New iTunes 11 for Windows work on Windows 98???

Will the New iTunes 11 for Windows work on Windows 98???
A. True.
B. False.

My opinion is no. Apple has no plans updating version 11 to meet the needs of Windows 98 being that #1 - Windows is pushing forward with their Windows 8 operating system launching in a week and iTunes 11 would have needed to be re-written from scratch to accomodate the Windows 7 and Windows 8 systems. It is a known issue that iTunes is bloated and most Windows users will use other media players to manage their music rather than iTunes. #2, Windows 98 is so old that even Windows does not recommend anyone using anything past XP as you are exposing your PC to viruses or anything that no longer can be patched. I highly recommend upgrading to atleast to Windows 7 and this is of course if your PC matches the bare minimum of hardware to use iTunes 10.7 and 11. You are actually doing more harm than good by using an outdated OS.

After installing windows 7 on my hp pavilion dv4000, the audio and vga caase to work. help me

after installing windows 7 on my hp pavilion dv4000, the audio and vga case to work. help me with a recommended sound and audio drivers for windows 7 operational system. Please
This question was solved.
View Solution.

Hi:
Please click on the devices in the device manager. Then click on the details tab. In the properties drop down list, select the second item (Hardware ID's). Post the top string of characters you see for each device.
Those will identify the model devices you have and I can try and find the drivers for them. Is it Windows 7 32 or 64 bit you have installed?
Paul

Will the 1tb and larger notebook drives work in my X60?

Similar Messages

Maybe you are looking for