Will the officejet 6500a plus be ready for printing when the mains supply is turned on

I am considring the purchase of an Officejet 6500a Plus (duplex is a prime reason) it will be used in a home office environment with Win 7 operating system. I can remotely swithch on the mains supply to the printer and router. Will the printer be available to print (after start up checks) without further intervention? eg. do i need to depress the start button on the printer?
Many thanks in anticipation Jimbow

The printer should come up "ready" after a minute or so and accept print jobs without any intervention on the front panel.
That said, it would be much better to leave the printer turned on and let the automatic power management take care of putting the printer into a low power state. If you remove power from the printer remotely there is a risk of having the printheads not properly capped after a print job. This can cause the printheads to dry out, causing print quality issues. It will also result in extra ink being used when the printer power is restored as more servicing will be performed on the printhead.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Similar Messages

Wireless configuration for HP OfficeJet 6500A plus All-In-One printer on Ubuntu 10.04

I have bought a HP OfficeJet 6500A plus All-In-One printer CN557A, which I want to use with ubuntu 10.04 64-bit as a wireless network printer.
Before i bought i checked compatibility on www.hplipopensource.org and www.openprinting.org, and all was in order.
The machine is autodetected and fully functional when connected with a usb cable, but i have not managed to get it to work as a wireless printer.
This is what I did:
I configured the printer on the wireless network (through the printer interface), and it connects. It prints out a "Wireless Network Test Report", and everything works. I can ping to its local ip adress, and access it through the browser. HP eprint also works.
I installed hplip 3.11.10 and dependencies manually. I did this because the default hplip in ubuntu 10.04 did not recognise the device.
I ran 'hp-check', which gave no errors or warnings:
tjoff@mek-403-jakbo-01:~$ hp-check
HP Linux Imaging and Printing System (ver. 3.11.10)
Dependency/Version Check Utility ver. 14.3
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Note: hp-check can be run in three modes:
1. Compile-time check mode (-c or --compile): Use this mode before compiling the
HPLIP supplied tarball (.tar.gz or .run) to determine if the proper dependencies
are installed to successfully compile HPLIP.
2. Run-time check mode (-r or --run): Use this mode to determine if a distro
supplied package (.deb, .rpm, etc) or an already built HPLIP supplied tarball
has the proper dependencies installed to successfully run.
3. Both compile- and run-time check mode (-b or --both) (Default): This mode
will check both of the above cases (both compile- and run-time dependencies).
Saving output in log file: hp-check.log
Initializing. Please wait...
| SYSTEM INFO |
Basic system information:
Linux mek-403-jakbo-01 2.6.32-35-generic #78-Ubuntu SMP Tue Oct 11 16:11:24 UTC 2011 x86_64 GNU/Linux
Distribution:
ubuntu 10.04
Checking Python version...
OK, version 2.6.5 installed
Checking PyQt 4.x version...
OK, version 4.7.2 installed.
Checking for CUPS...
Status: scheduler is running
Version: 1.4.3
error_log is set to level: warn
Checking for dbus/python-dbus...
dbus daemon is running.
python-dbus version: 0.83.0
| COMPILE AND RUNTIME DEPENDENCIES |
note: To check for compile-time only dependencies, re-run hp-check with the -c parameter (ie, hp-check -c).
note: To check for run-time only dependencies, re-run hp-check with the -r parameter (ie, hp-check -r).
Checking for dependency: CUPS - Common Unix Printing System...
OK, found.
Checking for dependency: CUPS devel- Common Unix Printing System development files...
OK, found.
Checking for dependency: CUPS image - CUPS image development files...
OK, found.
Checking for dependency: DBus - Message bus system...
OK, found.
Checking for dependency: gcc - GNU Project C and C++ Compiler...
OK, found.
Checking for dependency: GhostScript - PostScript and PDF language interpreter and previewer...
OK, found.
Checking for dependency: libcrypto - OpenSSL cryptographic library...
OK, found.
Checking for dependency: libjpeg - JPEG library...
OK, found.
Checking for dependency: libnetsnmp-devel - SNMP networking library development files...
OK, found.
Checking for dependency: libpthread - POSIX threads library...
OK, found.
Checking for dependency: libtool - Library building support services...
OK, found.
Checking for dependency: libusb - USB library...
OK, found.
Checking for dependency: make - GNU make utility to maintain groups of programs...
OK, found.
Checking for dependency: PIL - Python Imaging Library (required for commandline scanning with hp-scan)...
OK, found.
Checking for dependency: PolicyKit - Administrative policy framework...
OK, found.
Checking for dependency: PyQt 4 DBus - DBus Support for PyQt4...
OK, found.
Checking for dependency: Python DBus - Python bindings for DBus...
OK, found.
Checking for dependency: Python devel - Python development files...
OK, found.
Checking for dependency: Python libnotify - Python bindings for the libnotify Desktop notifications...
OK, found.
Checking for dependency: Python XML libraries...
OK, found.
Checking for dependency: Python 2.3 or greater - Required for fax functionality...
OK, found.
Checking for dependency: Python 2.2 or greater - Python programming language...
OK, found.
Checking for dependency: Reportlab - PDF library for Python...
OK, found.
Checking for dependency: SANE - Scanning library...
OK, found.
Checking for dependency: SANE - Scanning library development files...
OK, found.
Checking for dependency: scanimage - Shell scanning program...
OK, found.
Checking for dependency: xsane - Graphical scanner frontend for SANE...
OK, found.
| HPLIP INSTALLATION |
Currently installed HPLIP version...
HPLIP 3.11.10 currently installed in '/usr/share/hplip'.
Current contents of '/etc/hp/hplip.conf' file:
# hplip.conf. Generated from hplip.conf.in by configure.
[hplip]
version=3.11.10
[dirs]
home=/usr/share/hplip
run=/var/run
ppd=/usr/share/ppd/HP
ppdbase=/usr/share/ppd
doc=/usr/share/doc/hplip-3.11.10
icon=/usr/share/applications
cupsbackend=/usr/lib/cups/backend
cupsfilter=/usr/lib/cups/filter
drv=/usr/share/cups/drv/hp
# Following values are determined at configure time and cannot be changed.
[configure]
network-build=yes
pp-build=no
gui-build=yes
scanner-build=yes
fax-build=yes
dbus-build=yes
cups11-build=no
doc-build=yes
shadow-build=no
hpijs-install=no
foomatic-drv-install=no
foomatic-ppd-install=no
foomatic-rip-hplip-install=no
hpcups-install=yes
cups-drv-install=yes
cups-ppd-install=no
internal-tag=3.11.10
restricted-build=no
ui-toolkit=qt4
qt3=no
qt4=yes
policy-kit=no
hpijs-only-build=no
lite-build=no
udev-acl-rules=yes
hpcups-only-build=no
hpijs-only-build=no
Current contents of '/var/lib/hp/hplip.state' file:
# hplip.state - HPLIP runtime persistent variables.
[plugin]
installed=0
eula=0
Current contents of '~/.hplip/hplip.conf' file:
[last_used]
printer_name =
working_dir = .
device_uri = "hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW"
[commands]
scan = /usr/bin/xsane -V %SANE_URI%
[installation]
version = 3.11.10
date_time = 2011-11-16 14:30:35
[settings]
systray_messages = 0
systray_visible = 0
[fax]
email_address =
voice_phone =
[refresh]
rate = 30
enable = false
type = 1
[polling]
enable = false
device_list =
interval = 5
| DISCOVERED USB DEVICES |
Device URI Model
hp:/usb/Officejet_6500_E710n-z?s HP Officejet 6500 E710n-z
erial=CN16F2402Q05JW
| INSTALLED CUPS PRINTER QUEUES |
B-403-271-A4-COLOR2
Type: Unknown
Device URI: smb://mek-ps1.win.dtu.dk/403-271-A4-Color
B403-271-A4-BW
Type: Unknown
Device URI: smb://mek-ps1.win.dtu.dk/403-271-A4-BW
HP-Officejet-6500-E710n-z-FAX
Type: Printer
Device URI: hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW
PPD: /etc/cups/ppd/HP-Officejet-6500-E710n-z-FAX.ppd
PPD Description: HP Officejet 6500 e710n-z, hpcups 3.11.10
Printer status: printer HP-Officejet-6500-E710n-z-FAX is idle. enabled since 2011-11-16T01:00:45 CET
Communication status: Good
| SANE CONFIGURATION |
'hpaio' in '/etc/sane.d/dll.conf'...
OK, found. SANE backend 'hpaio' is properly set up.
Checking output of 'scanimage -L'...
device `hpaio:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW' is a Hewlett-Packard Officejet_6500_E710n-z all-in-one
| PYTHON EXTENSIONS |
Checking 'cupsext' CUPS extension...
OK, found.
Checking 'pcardext' Photocard extension...
OK, found.
Checking 'hpmudext' I/O extension...
OK, found.
Checking 'scanext' SANE scanning extension...
OK, found.
| USB I/O SETUP |
Checking for permissions of USB attached printers...
HP Device 0x5412 at 002:005:
Device URI: hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW
Device node: /dev/bus/usb/002/005
Mode: 0664
| USER GROUPS |
lp adm dialout cdrom plugdev lpadmin admin sambashare vboxusers
| SUMMARY |
No errors or warnings.
Done.
I then ran 'sudo hp-setup', chose the device (which was detected), chose my wireless network, entered the wireless security key. On the configuration results dialog I get two messages:
"Your printer has been succesfully configured on the wireless network. You may now unplug the USB cable"
and
"The Ethernet cable is plugged in which will prevent you from connecting to a wireless network. To connect wirelessly, remove the cable and try again. (VSA000)"
There is no ethernet cable plugged in, so i can't remove it. I unplug the USB cable and click 'finish'. This makes the 'hp-setup'-dialog start over again, and the printer has not been installed.
In the terminal i have the following:
tjoff@mek-403-jakbo-01:~$ sudo hp-setup
[sudo] password for tjoff:
HP Linux Imaging and Printing System (ver. 3.11.10)
Printer/Fax Setup Utility ver. 9.0
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Searching on USB bus...
GET /IoMgmt/Adapters HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/WifiNetworks HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/Profiles/Active HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/Protocols HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
error: Missing response key: 'iorotocols-iorotocol-dd:dnsserveripaddress-0'
GET /IoMgmt/Adapters/Wifi0/VsaCodes.xml HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/WifiNetworks/SSID=mVnmXfsu HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/IoConfig.xml HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
I then tried to reconnect the printer usb cable and run 'hp-toolbox' and click "Wireless/wifi setup using USB". Now i get the error:
tjoff@mek-403-jakbo-01:~$ hp-toolbox
HP Linux Imaging and Printing System (ver. 3.11.10)
HP Device Manager ver. 15.0
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
HP Linux Imaging and Printing System (ver. 3.11.10)
Wifi Configuration Utility ver. 1.1
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
error: Channel write error
error: An I/O error occurred. Please check the USB connection to your printer and try again. (Device I/O error)
Done.
I do not how get past this stage, and any help is welcome.
This question was solved.
View Solution.

A friendly soul on ubuntuforums pointed out to me, that the wireless configuration is only necessary when the printer is NOT connected to a (W)LAN. So all I really had to do was to configure the printer in the CUPS administation page, and it worked. Problem solved. Silly me.

How do i print from my ipad to the officejet 6500a plus?

I read there may be something else required. I want to print directly to the Officejet 6500A Plus. Apple says ths is an Air Print printer capable of doing that. I'm not taking this monster out of the box until I know it will do what I want without a lot of trouble. Thanks.
This question was solved.
View Solution.

Ok, so you were talking about needing the update. It's hard to say as it all depends upon if it came with the new firmware or not. It is not really relevent, however, since it will update itself upon enabling Web Services. This process takes only a few minutes. There is no computer necessary for the firmware update as long as the printer has internet access (i.e. connected directly to a router via either ethernet or wireless). Yes, with an ad hoc connection, you will be able to print from the iPad, but you would have to use its 3G connection as opposed to going through your router. It can only support a single wifi connection also. Go ahead and set up the printer and keep me posted as to what happens.
BTW - What is the issue with your PC that it cannot access the internet?
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided.
Although I work for HP, my posts and replies are my own opinion and not those of HP.

HP Officejet 6500A Plus will not maintain wireless connection reliably

For the HP EXPERTS on Expert Day, April 18, 2012:
B.L.A.T. (Bottom Line At Top): We have an HP Officejet 6500A Plus purchased about 5 months ago. We wanted to use it as a wireless-connected printer in another room besides our home office. It is useless to us because it will not maintain its wireless connection, even sitting just a few feet from the router in the same room. Except for numerous hours of troubleshooting, we have left it sitting powered up, but unused and idle, for almost the entire 5 months in our home office. DURING ALL THAT IDLE TIME, IT HAS LOGGED OVER 3,200 DISCONNECTS, at a consistent rate of 24 disconnects every 24 hours, even though it ALWAYS reports that the wireless signal quality is “EXCELLENT” (all this is according to the Wireless Network Test Reports we’ve printed throughout the last 5 months). So our question is, what is it that this printer is trying to do once an hour over a wireless connection that is causing these thousands of disconnects? And how can we stop it?
NOTE! Before you round up the usual suspects (namely our router and our PC firewalls) please note that we also bought an HP Officejet Pro 8600 Plus ON THE SAME DAY as the Officejet 6500A Plus. The 8600 was also installed with a wireless connection, and has worked without a single network issue for the entire 5 months.
NOW, FOR THE REST OF THE STORY…
WHO WE ARE: My wife and I have worked on HP equipment for 33 years, starting in 1979 as corporate customers of HP when we worked for Exxon; then we both worked for HP directly for 17 years; and we’ve now used dozens of pieces of HP equipment in our home during the last 12 years in retirement. We’re primarily software folks, so we’re not exactly experts in hardware and networking, but on the other hand, this ain’t our first rodeo either.
OUR CONFIGURATION:
PC’s – All running Windows 7 x64 with all important patches applied and Norton Internet Security 2012: HPE-270f and HP AIO 200-Quad, each with full 6500A and 8600A drivers installed on wireless connection. These 2 PC’s themselves can connect either wirelessly or via Ethernet to our home network. The 270f has a dual-band wireless board. Both bands work. We also have a new dv7t laptop with only the full 6500A driver installed via wireless connection. The laptop is now upstairs and it’s connected to our home network wirelessly without any issues. (This is where we had hoped to also put the 6500A, but it needs to work reliably via wireless connection.)
ROUTER: Netgear N600 WNDR3700 providing Ethernet and wireless networking. Router provides a very strong wireless signal throughout the house. No wireless problems with any other equipment including an iPod, two Kindle Fires besides all the HP equipment.
PRINTERS: Besides the two HP printers, the HPE-270f PC has a Canon MP960 installed on it. And if we can’t get the 6500A working right or replaced with something that does work right, we may be buying our second Canon printer. By the way, on the 6500A, ePrint and App’s are set to ON, but of course they’re not being used, just like everything else on this AIO.
OTHER: We also have a Sonos music system that connects to our network via Ethernet and has its own proprietary mesh network (on another frequency) for transmitting ripped music wirelessly to speaker units throughout our house. (If you aren’t familiar with this totally cool system, check out sonos.com). We’ve never seen any evidence of interference between these two wireless networks, or our wireless phone sets either.
HP TOOLS AVAILABLE ON ALL 3 PC’s: HPU
UPDATE 5.003.001.001 (reporting everything up-to-date); HPHDU 3.1.0.17; HPPDU 5.0.0.015 and HPNDU 4.3.0.002.
SYMPTOMS: The 6500A Plus installs quickly and easliy, and connects wirelessly just fine during installation. But sometime over the next hour (usually less), it disconnects and won’t print from PC applications. Sometimes the application puts up an “Unable to communicate with printer” screen, even though the PC usually thinks the printer is “ready”. Other times, the PC thinks the printer is offline (but printers don’t have “offline” buttons anymore!). Often, if you just leave everything alone, the 6500A will somehow reconnect and print out the spooled file 5-30 MINUTES later. So it does usually seem to be able to recover given some time, but that doesn’t always fit our schedule! Occasionally, turning the wireless radio on the printer off and back on will fix it right away. But usually, you have to power the printer completely off, and then back on. As far as we know, that always fixes it…..until the next disconnect a few minutes later!
PREVIOUSLY TRIED: After reading some of HP’s wireless network support websites, I manually assigned a fixed IP address to this printer. It didn’t seem to matter; according to the wireless network test report, it still logs disconnects at the rate of one per hour, and all the failure symptoms were the same.
We also dabbled a bit with setting this printer as “trusted” to the Firewall, but that didn’t seem to matter either.
Next, we connected the printer via Ethernet. The printer immediately started to work, even though it had just been in its “failed” state over the wireless connection. As far as we know, it never failed while connected via Ethernet. This seems to point to a purely wireless hardware/firmware problem on the printer itself.
Late last year, I tried two different chat sessions about this with the inter-continental AIO support teams, each one lasting several hours. Unfortunately, none of their optimistic solution scripts seemed to fit our problem. They both seemed determined to reconfigure the 6500A as a TCP/IP printer, which of course worked fine initially, just like everything else. At this point, they would understandably want to close the chat. But 20-30 minutes later, we could no longer print to it. During the second chat, they got into one of our PC’s remotely and effectively turned off the spooler (by selecting “Print Directly” or something like that). After that, all was well again (as usual) UNTIL the printer disconnected, at which time attempting to print from that PC would HANG the application (since the spooler was no longer buffering) and eventually hang the whole PC. One giant leap backwards. That’s when I gave up on the multi-hour chat sessions.
The three diagnostic utilities (HDU, PDU, NDU) have been tried over and over. When the printer is in its disconnected state, the DU’s usually don’t detect the 6500A at all, or if they do detect it, they are unable to fix anything. Frankly, it’s easier to just power the printer off (which takes about a minute) and power the printer back on (which takes more than a minute) and then wait for the spooler to kick in (usually about 30 seconds). BUT WE DON’T CONSIDER THAT A SOLUTION!!
B.L.A.B. (Bottom Line At Bottom): We have used up nearly the entire black ink cartridge and at least a ream of paper troubleshooting this brand new printer, to no avail. This printer is useless to us unless it can maintain a wireless connection reliably. Please help!
Thanks –
Bob and Jane
(Note: we have an appointment from about 11:20 am EDT – 1 pm EDT, 8:20 am PDT till about 10 am PDT)

I bought the Officejet 6500A Plus about one month and have experienced the very same problem. I tried to remedy this problem following suggestions in a number of different posts (static IP, router, firewalls etc), all to no avail. Last week I called support. The support I received by the tech over several hours and different days for a week was very good. However none of his suggestions corrected the connection issue. After today's recommended fix failed, he advised HP is aware of this issue with the 6500 and other affected printers. He claimed HP was working on a firmware upgrade. He did not know when the update would be provided. The tech also claimed HP acknowledged this problem in a written announcement. He agreed to email the announcement to me. I haven't received it. This has been the only problem I've had with the 6500

Windows Folder icon instead of Officejet 6500a Plus E710n icon in Devices and Printers

Can anyone help me to get the OfficeJet 6500a Plus e710n printer icon to display properly in Devices and Printers?
I recently reinstalled Windows 8.1. However, when I installed my printer, instead of the printer icon appearing in Devices and Printers I get a generic yellow Windows folder icon. The Fax icon is OK, just the printer icon is wrong.
If I double click on the icon, I get a mostly blank page with a message near the top saying: "Updated information is available about your device. Click here to download or learn more." If I click on the notice, a dropdown menu appears with "Download updated information" or "Learn more". If I choose downloaded update information, a new printer window appears which is mostly blank except for a message at the centre of the window which says, "No tasks are available on this page" The Learn more option just gives me info about updating drivers.
The printer icon on the Start menu is fine.
I've used HP Print and Scan Doctor to uninstall and reinstall my printer but this hasn't helped. The program found a problem with the printer driver and fixed it, but that hasn't changed the icon either.
I am running Windows 8.1 Pro 64bit fully up to date, and used the latest full version of the HP installation program for the printer (not the basic version) and HP Print and Scan Doctor v4.6.
This question was solved.
View Solution.

Hi,
Try following these steps and let me know if that may help:
From the control Panel select Network and internet and open the Network and Sharing Center.
Click on Change Advanced Sharing Center.
Ensure that Network Discovery is trned on but uncheck the box next to "Turn on automatic setup of network connected devices".
From devices and printer right click the printer and select Remove Device, repeat the for the Fax icon.
Note: if no such option exists for the printer follow the next steps.
Right click the background area and select Device Mahager.
Remove any instance of the printer from Imaging Devices, Printers, Print Queues, Multifunction Adaptors, Other Devices (if a such exists).
Once you are done the printer should no longer appear under Devices and Printers...
Open teh HP Officejet 6500 E710 software, select Connect a new Printer and check for any differnce.
Hope that helps,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Photoshop Elements 12 no longer see's my scanner. So I cannot scan my pictures, help. Windows 8.1 with HP Officejet 6500A Plus printer. Scanner works with other programs in my PC. Problem is PS12

So I cannot scan my pictures, help. Windows 8.1 with HP Officejet 6500A Plus printer. Scanner works with other programs in my PC. Problem is PS12

I bought the Officejet 6500A Plus about one month and have experienced the very same problem. I tried to remedy this problem following suggestions in a number of different posts (static IP, router, firewalls etc), all to no avail. Last week I called support. The support I received by the tech over several hours and different days for a week was very good. However none of his suggestions corrected the connection issue. After today's recommended fix failed, he advised HP is aware of this issue with the 6500 and other affected printers. He claimed HP was working on a firmware upgrade. He did not know when the update would be provided. The tech also claimed HP acknowledged this problem in a written announcement. He agreed to email the announcement to me. I haven't received it. This has been the only problem I've had with the 6500

HP Officejet 6500A Plus

My HP Officejet 6500A Plus all in one printer recently stopped functioning and printing. First the Wireless network stopped working (Wireless Status Disconnected) and the Wireless Netwok Test Report advice was “contact HP support”. Then I started getting endless errors and flashing print screens with numerical references like 83C00009, 00729C98 etc. Any attempt to turn off the printer using the “off button” resulted in another error message. The following are examples of the stream of new error messages that appeared each time the “off button” was pressed: B0000A16; B03DA14A; B811DEB6; B8383184; B03E3B66; B83D99B8 etc. To finally “turn off” the printer it became necessary to disconnect the power. I have consulted the manual and queries on the HP site using the numerical references as search criteria, does not return any useful results / strategies. I found a video about how to do a partial “reset” (turn on using # + 3) but while this did allow me to access the print screen, it did not resolve anything and the numerical errors and flashing lights reappeared. I downloaded the HP diagnostic tools, but they came up with nothing – i.e. could not communicate with my printer. I read on some post that there may be a problem with the printer head, so I ran the Printer Status Report, but it seemed OK. Regardless I ran the clean the PrinterHead tool, and again this seemed OK, so I didn’t run the 2nd stage. My printer is out of warranty. It is 1.5 years old, but hasn’t been used that much. According to the Printer Status Report it has printed 1534 pages and scanned 290.
What can I do? Most of the "internet searches" suggest that if the printer is out of warranty the only option is landfill.

Thank you. Thesole reason I bought this printer was to use its wireless “Airprint” functionality to print from an iPad and when it worked it was a fabulous product. The start of these constant alphanumeric errors seemed to coincide with the wireless function ceasing to work (it went offline, HP Network Configuration Report – Network Status “Offline”, and Wireless status “Disconnected”). Maybe that was just a coincidence. Running the “Wireless Network Test Report” the recommendation is “Contact HP support***”. I.e. The Wireless is on (blue light good) PASS, but the Wireless Working status is FAIL.
I have only tried using the USB in an attempt to get around the wireless not working, i.e. still able to do some basic printing and perhaps upload firmware updates etc. I have tried different USB ports on my laptop computer but only with the same USB cable that came with the printer. This original printer cable has only been used a couple of times and it has on two occasions allowed me to print successfully from the laptop (i.e. initially it worked although . Surely it should be OK. I am reluctant to go out and buy another cable in the hope that it might resolve something and I don’t really have access to another computer to test.
Thank you I have previously seen that article. It was somewhat useful. My errors messages (mostly 83C0009, and sometimes just a black and white striped screen or B0525DAE, B866A570 etc) however do not include system ink failure and the article basically therefore simply recommends switching the computer off at the same time the ink cartridges are removed. This has in the past provided some improvement in the frequency of the error messages but it is usually short-lived and the error message returns. The error message can however become entrenched and at that point the print cartridges don’t move when the printer door is open and therefore can’t be removed. At this point I've tried turning the printer on while holding down #+3 to try and get back to a home screen, rather than an error screen.
On the upside, I can occasionally still make photocopies and the print quality is good.
Any guidance on what I should do next?

I cannot get my HP Officejet 6500A Plus 710N to print in color. I have reinstalled the drivers..

I cannot get my HP Officejet 6500A Plus 710N to print in color. I have reinstalled the drivers. It used to print in color and just stopped. I think it may be a settings issue? I have checked the ink levels and they are all fine. When I print a diagnostic report on print qualify, the black prints well, but there is no color printing.

Okay, I had the same problem. It's most likely your printhead. All you have to due is clean it.
Note: I was sceptical of this approach but can fully attest to it's sound results as it restored my printer back to full functionality. Prior to this the printer only would print Black ink.
The print head is the carriage that holds all of your ink cartridges in the printer. On the 6500A it's super easy to remove. Opent your lid like your changing your ink cartridges. Remove all of your ink cartridges. Once they're out. There is a lever on the left side of the carrier that holdes your ink cartridges. Lift it up and the print head comes right out. Net take your print head to the sink and run it under hot water aiming towards the the four cirles were the ink flows into. Keep running it under the hot water until it is coming out clear. It's okay to run it under the bottom part too infact you'll need to inorder to get it completely rinsed out. Also don't touch the computer metal strips with your hand thought you can run water over them. Once your done rinsing use a blow dryer or a can of compressed air (thats what I did) to dry every thing out. I was able to get everything dry in about 5 minutes or so. Let it sit for a few minutes and check it again for water. I recommend moving it around to get full exposure to insure it is dry. Also if you use a hair dryer try to put it on a cold setting since there ar rubber grommets the surrount the inlet ink ports you wouldn't want to melt them with the hot air etc.. Like I said I used a can of compressed air. It's important to use a quick method of drying as mentioned otherwise mineral particles could become deposited on the unit. This won't happen with the methods as I've described because the molecules won't be able to bond since your blowint them off. Oh yeah, you'll want to place a clean peice of paper down as your blowing because at first you'll end up with a few black jet marks as your blowing. Also don't wear your favorite white shirt lol.
Okay once it's dry replace the print head carriage back in push the lever down install the ink cartridges. Close the lid then unplug the printer. Wait 5 seconds plug it back in then it will reboot and start its set up procedure kind of like whet you first bought the printer except you won't have to change any of your network or setup setting since they are saved in memory. Also be patient about the set up procedure it seemed very slow for me. Once it finishes you will be prompted to run the printer alignment process. Run the alignment process and you should be all good. If not at least you gave it a shot. If this doesn't work your going to have to pay $60 for a new printer head. Which is not that big of a deal but hey if you can fix it for free why not. If you do decide to buy a new printer head you might find deals online or ebay just make sure it's an Genuine HP print head. And lol use the Genuine HP ink cartridges. Finally make sure you print at least on colored page per month to make sure the ink doesn't clog up in the future.
Remember this suggestion is after you have run the HP clean ink cartridge procedure twice. Sometimes the clean procedure will correct the problem first. Also there is video I watched on YouTube about this just search for "Clean HP 6500 print head. Hope that helps
Once it's all dry just reinstall the printer head carriage

How to set Default COPYING for HP Officejet 6500A Plus to DRAFT Quality?

How do I set to Default COPYING quality to DRAFT for HP Officejet 6500A Plus?
This question was solved.
View Solution.

Hi,
Tap Copy on the printer front panel, then tap the Settings button.
Tap Quality and select Draft / Fast.
Tap Set as New Defaults and then select Yes to confirm the changes.
From now on draft quality will be used for copying unless any other quality will be selected.
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Can't use the feeder of a Officejet 6500a plus

I just bought a new iMac (os x 10.9) and with the use of the os x 10.8 driver I could install my Officejet 6500A Plus. Now I want to use the feeder to scan some documents and I want to send it to my iMac but the following notification is shown: "you can start a scan from your computer or scan to your computer from the printer. make sure the HP printer software is installed. Windows only - Network connection in the hp printer software, enable the activate scan to computer function."
Can someone tell me what I'm doing wrong?

Hello Tim_Aelbrecht,
Welcome to the HP Support Forums! I see you are using the new Mavericks 10.9 OS with your HP Officejet 6500A Plus, you would like to scan from the front panel, but you are not given the option. With the newer 10.9 OS, there were no full featrue software and drivers made, this is why you are getting the error message. To get a better understanding, continue below.
Seeing as there are no full feature software and drivers you cannot scan from the printer control panel without a Full Feature driver, you can still scan without the Full Feature HP software installed on your computer by using a basic set of scanning drivers. These drivers enable scanning from Apple Preview or Apple Image Capture. You can also scan from the Print & Scan window. Find out how here: How to Scan: OS X v10.9
I hope this helps!
Thanks,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Is there a software update for Apple's Lion OS and my Officejet 6500A Plus?

Has HP released a software update for Apple's new Lion OS (10.7.2)? My HP OfficeJet 6500A Plus can't find my computer most of the time. scan to computer no longer works since I installed Lion. Now the printer is not recognizing an HP-brand yellow ink cartridge--I've installed TWO new ones already! What a waste. HELP!
Thanks,
Jim

Had a text from Nokia on my 3 N8 today saying keep your N8 up to date.
Couldn't find an update through 3, but went to the UK Nokia website and managed to update from software version 011.012 to 013.016 which takes the release from PR1.0 to PR1.1
Update went very smoothly.
Still trying to track down specific details of the fixes and improvements in this update.
However, I have read that in April 2011 there will be a Release PR2.0
I am particularly interested in this as I understand that it will allow user-defined bookmarks to be added to the Home Screen with their particular "icon" rather than the generic icon, so that you can see in a sort of (dare I say it here?) iPhone way which webpage you are going to access...
We'll see.

Email/code for Officejet 6500A Plus

I can not find the printer email/code on my Officejet 6500A Plus. I'm trying to sign up for ePrint.

Hi David
For Officejet products
- Ensure that your printer is connected to the internet either wirelessly or through an ethernet / LAN cable
- On the printer's front panel display, touch Setup>Web Services Setup>Printer Email Address to reprint the information sheet. The email address of your printer will be the code on the information sheet
eg [email protected]
A full FAQ on setting up your printer can be found at
http://h30495.www3.hp.com/about/eprint#a1-3
Say Thanks by clicking the Kudos Star. Please mark the post that solves your problem as an Accepted Solution so other forum users can utilize the solution.
(Although I am an HP employee, I am speaking for myself and not for HP) I am not a expert on all our products, but I'll do my best to help you.

Does apple make a printer for iPad if not how dow I get it to work with a HP Officejet 6500A Plus printer?

Does Apple make a printer for the iPad and if not how do I get it to work with a HP Officejet 6500A Plus printer? Thanks

Apple don't make any printers, but there are a number of the printers that are AirPrint-enabled, which you should be able to print to just by the printer and the iPad being on the same wifi network - the models that support AirPrint are listed on this page (the page also includes a bit of troubleshooting at the bottom of it) and it includes :
HP Officejet 6500A e-All-In-One E710a
HP Officejet 6500A Plus e-All-In-One E710n
If your's isn't one of those then you could see if HPs own ePrint app works with it, or there are third-party printer apps such as PrintCentral Pro and Print n Share which might work it

Officejet 6500A Plus, trying to download driver for Win 7

Officejet 6500A Plus, trying to download driver for Win 7, but won't work on HP's site. Any ideas where I can get the driver?

Hello,
Please download and run the HP Printer Install Wizard from www.hp.com/go/tools
Regards,
Jabzi
Give Kudos to say "thanks" by clicking on the "thumps Up icon" .
Click "Accept as Solution" if it solved your problem, so others can find it.
Although I am an HP employee, I am speaking for myself and not for HP.

I have a new HP Officejet 6500A plus. I cannot get it to connect to my Airport Extreme V5.6. It see the wifi signal but Fails on "Filtering" and possibly the channel. Does anyone know how to reset or reconfigure filtering

I have a new HP Officejet 6500A plus. I cannot get it to connect to my Airport Extreme V5.6. It see the wifi signal but Fails on "Filtering" and possibly the channel. Does anyone know how to reset or reconfigure filtering and channel on the old airports?

This is a part of the larger MacBook Pro connectivity issue. There are several related threads dealing with the MBP's networking problems. If your unit is suffering from this type of difficulty, good luck ... (or a long ethernet cable)
(PS Everybody please make noise on this one so apple comes up with a solution.)
< Edited by Host >

Will the officejet 6500a plus be ready for printing when the mains supply is turned on

Similar Messages

Maybe you are looking for