Will the X-Fi Fatal1ty run on the MSI K8N Neo4 platinum SLI Bo

Hi there i was just wondering becasue i have heard some things that it wont run together very well and some people say that it works sometimes and then kicks out. Feedback would be greatly appreciated. Thanks Aaron

Hi Aaron,
The problem described in the "X-Fi Problem (rebooting)" thread does not affect the cards that have X-RAM.
I have a slightly different version of that board at home (MSI K8N SLI Platinum, not Neo4 model) and I'm running an X-Fi Fatalty FPS card on it, with no problems whatsoever.
Cat

Similar Messages

  • Anyone get 2gb Memory to run at 1T in K8N Neo4 Platinum SLI MB?

    I recently upgraded to 2 GB Geil memory in my new K8N Neo4 Platinum SLI system (not the system listed in my signature).  I cannot get it to boot if I set Ram to 1T.
    Has anyone been able to run 2GB at 1T in this MB?
    Thanks.
    fafner

    Thanks all for your comments.
    I have the Geil Value 2x1gb dual channel kit. It is rated at 3, 4, 4, 8.  I can get it to run fine at 3,3,3,8 at 2T.  I cannot get it to boot at 1T with either the rated settings or the faster settings.  It will boot at at 2.5, 3,3,8, but is not stable.
    I can exchange this kit for a higher quality kit, but I don't want to do that unless someone else has had success with runing 2x1gb in this Neo 4 Platinum SLI board.
    The memory I have runs at 1t in my K8Neo2 system as my does my Kingston Value RAM (2x512).  It so happens that I have 2 Kingston value kits (total of 4x512), which I could try but everything I have read says it will run at 333mhz with four stix.
    My experience has been that the K8N Neo2 Platinum is more accepting of value memory in general than the K8N Neo4 Plat/SLI.  I have also read that getting any 2x1gb kit to run at 1T in the Neo4 Platium/Sli board is impossible or at least nearly so.  That is why I am looking for soneone who has success (or no success) with 2x1gb sticks at 1T in the same mb as mine.
    Net I want to get the best 2gb configuration possible but onle one that someone already has experience with (since I can only exhange the Geil kit once).

  • Considering the MSI K8N Neo4 Platinum

    Hello,
        I'm currently deciding whether or not to get the MSI K8N Neo4 Platinum, and I just have a few questions.
    1) How beginner friendly is it?
    2) Does it take a lot of work to make it run or can you just plug everything up and the system will run fast and stable?
    3) How stable is this board? I've heard that MSI boards were unstable, so how stable is this specific board?
    4) I know this board is good at gaming, but how about office work like using Microsoft Word, Excel, Powerpoint, etc.?
    5) I plan to keep this system for at least four years, will this motherboard give a lot of trouble? And how reliable is it?
    5) Can ya'll share your experiences with MSI?
    Thanks for any help.

    Quote from: ExpertNovice on 30-June-05, 03:43:00
    Is the MSI website http://www.msicomputer.com/product/p_spec.asp?model=K8N_Neo4_Platinum/SLI&class=mb where MSI names the board as "K8N Neo4 Platinum/SLI" incorrect?  It wouldn't be the first time a typographical error occurred.
    If not then the OP may simply have not had enough room to enter a complete description.
    No it is not incorrect, I am staring at the box mine came in.  It says Platinum Edition-K8N Neo4/SLI, there is also a the non platinum version K8N Neo4/SLI and the non-SLI K8N Neo 4
    anyway,
    Quote
    Maybe I'll get the Platinum SLI edition instead so that I can upgrade later to SLI without having to buy a new card. If I do get the SLI I'll use a single card for now and put in the second card later when it's needed. Does the MSI K8N Neo4 Platinum/SLI have any problems with running a single video card in non-SLI mode? And I've noticed that the SLI edition doesn't have a x1 PCIe or x4 PCIe slot, is sacraficing these two slots (as well as a regular PCI slot) worth it for SLI capabilities?
    to answer that question, no it does not have problems running a single card in non SLI mode.  It runs like a champ.  I pernonally would not use the extra PCI slots, so to me SLI outweighs scarificing the extra PICe slots.

  • How are some guys running an Athlon 3800+ X2 chip on the K8N Neo4 Platinum SLI?

    I see many people running an AMD Athlon 64 3800+ X2 Dual Core proccessor on a K8N Neo4 Platinum SLI board, but mine dosen't work.  I don't get any signal to my monitor (don't know if this is the cause).  MSI says the 3800+X2 dosen't support the SLI board, but many people got it to work.  Any one know how?

    Mine working fine, but on cold boot, sometime it hang on me. I have changed 3 PSU to get it stable, from Coolermaster 450W, Be Quiet 520W to Silverstone 650W, ambient 25C, CPU 30C, Proc 37C.
    Bios 3.7 the one they are still testing.
    Have you check you PSU rails volt., disable CnQ,....
    So far stable, multiple programs at once with no significant drop in responseness & speed,  Half Life 2, P2P downloading x2, IE x 3, encode DVD at the same time.

  • X2 3800+ (E6) support for the K8N Neo4 Platinum/SLI

    Hi everyone:
    I have decided to purchase the K8N Neo4 Platinum/SLI (MS-7100-020) and I ready placed the order.  However, I wonder if it supports the AMD X2 3800+ (E6 Version) CPU?  The reason I asked the question because I found the following table from the Taiwan MSI web site which shows that X2 3800+ E6 is undertesting.
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=641&kind=1
    Thank you for any replies.

    Mine worked, ran for 2 weeks already at stock, tried & ran to 2.2GHz on stock HSF with no problem.
    Using X2 3800+ E6, MSI K8N PLI Platinum mobo, 3.7 bios & Inno3D 7800GTX single latest nvidia 78 drivers, 2x512MB DDR400 CL2.5 Kingston Ram, Hitachi T7K250 Sata 250GB HDD, NEC ND-3530A Benq 1640, , Silverstone Zeus 650W PSU
    At first I have this concern too, but tried it anyway.
    See my screenshots for your info.

  • MSI K8N Neo4 Platinum -- USB 2.0 will not work

    All of my USB 2.0 devices transfer at 1.1 speeds. My iAUDIO M3, all of my sandisk USB drives, and my camera...
    I have SP2 and USB 2.0 drivers:
    USB is enabled in the BIOS. When I plug in any of my devices, windows DOES NOT give that "this device can perform faster" balloon message, so windows thinks that everything's fine and dandy.
    USB 2.0 has never worked on this computer even after 4 formats. I formatted last thursday and installed things in this order:
    1 - windows
    2 - windows sp2 using the .exe file found here: http://www.microsoft.com/downloads/details.aspx?FamilyId=049C9DBE-3B8E-4F30-8245-9E368D3CDB5A&displaylang=en
    3 - latest nvidia nforce chipset drivers straight from the site.
    4 - all the other stuffs
    My problem could be in step 2, as the same .exe file to install sp2 on my nforce3 shuttle machine and that's experiencing the exact same problem.
    However, there's no logical reason why step 2 should be the culprit. USB 2.0 SHOULD work.
    Just wondering if you guys had any ideas... I'm stuck 

    Quote from: BOSSKILLER on 06-June-06, 11:44:02
    hello.
    did you tried back USB connection(integrated with mobo)?
    btw if you didnt use that Nvidia Nforce Network, better to disble it from the BIOS insted from device manager couse cause slow XP boot. also better to use XP instalation with including SP2 on it to keep OS performance level intact.
    I'm using the USB connections straight from the mobo on the back of the computer.
    I disabled the network thing because I'm using a wireless card right now, but I'll switch back soon. Thanks for the tip, though. I didn't think of it
    I figured it was better to use a slipstreamed SP2 install disk, but I don't have one. I'll do it next time.
    Still, any ideas? I want to make sure I'm not missing any basic checks before I reformat again (:() and fix step 2 to see if that changes anything (again, it shouldnt!).

  • K8N NEO4 Platinum the boat anchor from hell!

    I just asembled the following:
    MSI-7100-030 K8N NEO4 PlatinUm SLI
    Geoforce 6800 PCIE
    2 Gig DDR400
    2x200Gb WD SATAII drive
    2x80GB  Seagfate SATA drives
    2x80GB  Wd IDE drives
    I get terrible performance.
    Takes One hour to copy a 6Gig file to another drive or folder.
    Multi tasking is almos nonexixstant.
    I got this board as a white box [oem].
    No software or manuals.
    So I Dl'd the system & raid drivers from MSI.
    As i did not run well I then got updated drivers form Nvidia & from Silicone Image.
    No better.
    I ran a benchmark program (Passmark Perfomance Test) and was very unhappy.
    Has anyone had similiar issues?
    Would anyone download a copy of this software from:
    http://www.passmark.com/download/pt_download.htm.
    Please run the "Run All test Sequentially" icon [second from end of tolbar].
    Save & email me the results at [email protected]
    Should take no more than 5 minutes.
    Please specify your system build for comparison.
    Thanks & happy newyear!

    selkov,
    you don't appear to have a CPU or PSU in your system, can you tell us what they are please?

  • I tunes on my iphone will not play songs. it runs through the library at break neck speed when i click on a song...help!!, i tunes on my iphone will not play songs. it runs through the library at break neck speed when i click on a song...help!!

    i tunes on my iphone will not play songs. it runs through the library at break neck speed when i click on a song...help!!, i tunes on my iphone will not play songs. it runs through the library at break neck speed when i click on a song...help!!

    Try force-closing the Music app: from the home screen, double-tap the home button, locate Music in the list at the bottom, tap and hold it until it wiggles, tap to close it, tap the home button again, then try to play your music again.

  • I installed iWork11 but the '09 versions of the software are still running--and the default. What do I need to do to get the '11 versions working?

    I installed iWork11 but the '09 versions of the software are still running--and the default. What do I need to do to get the '11 versions working?

    It's very simple. If you want to use iPhoto, just let it manage things as it does. Other than that: Export from iPhoto and delete the image from iPhoto. That will remove the master and all versions.
    If space is an issue... use an external disk.
    Don't change anything in the iPhoto Library Folder via the Finder or any other application. iPhoto depends on the structure as well as the contents of this folder. Moving things, renaming things, deleting them or otherwise making changes will prevent iPhoto from working and could even cause you to damage or lose your photos.
    Regards
    TD

  • The agent service is running, but the request failed for ...

    Hi!
    ZCM 10.3.3 on SLES 11. HP notebook, Windows 7 Pro SP1.
    When WiFi is also switched on I got yellow diamond in ZCC and error "The agent service is running, but the request failed for one or more known addresses.". What this does mean? WiFi off -- green again! =)
    More thanks, Alar.

    Does the address it's getting via Wireless have a path back to the ZCM server? That was my point. If your wireless is vlan'd away from the wired network, ZCM won't be able to contact it through THAT particular address and will show the yellow diamond as a result even though it communicates fine through the wired address.

  • Hi, I've just downloaded Aperture 3.2 and transfered all my iPhoto Library but now when I use the Aperture program it runs at the slowest speed possible and is almost impossible to work with. It is constantly processing why is this?

    Hi, I've just downloaded Aperture 3.2 and transfered all my iPhoto Library but now when I use the Aperture program it runs at the slowest speed possible and is almost impossible to work with. It is constantly processing why is this?

    You can click on the text that says 'processing' in the main windows and it will open (toggle) the Activity Window, (can also be accessed via the Window menu -> Show Activity.
    It will tell you what Aperture is doing with more precision and perhaps even how many photos it still needs to process. It is generally best to wait until all that processing is done before you start working with the photos (well it is best to first turn of options what you dont want to use, perhaps Faces or Previews and then let it process the new photos).

  • How do I remove the coloured bars from running down the side of my emails.

    How do I remove the coloured bars from running down the side of my emails.

    Hi
    The setting I have in Composing are-
    Composing
    Message Format - Rich Text
    In addressingonly have  tick in When sending to a group
    Responding - tick only the first two boxes
    Last only the bullet for Include selected text
    Hope htis helps

  • The new version of firefox does not shut down when I close the browser it continues running in the background. In addition it opens Adobe Reader for a brief time and then that closes. Everything worked fine before this new version.

    Firefox automatically loaded a new version recently. The new version does not shut down when I close the browser it continues running in the background. In addition it opens Adobe Reader for a brief time and then that closes. Everything worked fine before this new version.

    See "Hang at exit":
    * http://kb.mozillazine.org/Firefox_hangs
    * https://support.mozilla.com/kb/Firefox+hangs

  • HT4515 How to make sure that after browsing that the webpage is not running in the background, but totally closed down

    How to make sure that after browsing that the webpage is not running in the background, but totally closed down

    Double tap the Home button, tap & hold the Safari icon until it starts to wiggle, tap the red minus sign to remove it from the Multi-Tasking bar. Tap the Home button when finished.

  • HT201365 Before I downloaded the iOS 7 upgrade I could turn off the apps that were running in the background by double clicking the bottom button to bring up the apps. I would hold down on 1 app, X's would appear on each and then I could close them. How N

    Before I downloaded the iOS 7 upgrade I could turn off the apps that were running in the background by double clicking the bottom button to bring up the apps. I would hold down on 1 app, X's would appear on each and then I could close them. How Now?

    and
    Because my first response would be....Oh, sure.....
    Because I am sorry you are having a hassle with the intenet. There is nothing more frustruating than having to deal with a slow response, or a makeshift connection....hope it gets fixed soon!!!
    Your friend,
    GB

Maybe you are looking for

  • Print out of Change Purchase Order

    Dear All, Could u please tell me how can i get the Chnage to Purchase order Print? As far as my knowldge we have to go to ME22n & then message then select the output type but after doing all this i am unable to get the print out with Change to Purcha

  • Regarding  using BAPI s

    Dear Friends,                    Can anyone tell how to use BAPI s in our programs as i have knowledge in creating a bapi.                    I  know what BAPI s are, and have founded no information how to use it externally to connect other external

  • Unable to embedded xls files word doc with acrobat distiller 6

    Hi, I have a problem to convert a Microsoft Word docs with embedded excel(*.xls) to PDF using Adobe Distiller 6. The excel file will become an image file after conversion. Please advise on what went wrong or is this a limititaion of Adobe Distiller 6

  • How to add date in XSLT?

    All, soa version: 11.1.1.4 There is a requirement for me to add date to the current date in XSLT.  I searched in 'Data functions', there I couldn't find any pre-defined functions.  How do I achieve it in XSLT?  Any help is appreciated. thanks sen

  • Is it possible to use XSS 2005 on EP7 with ECC 5.0 ?

    Hi all, I have an ECC5.0 and I want to upgrade my EP6 to EP7. I'm using XSS 2004 on EP6 and I want to use XSS 2005 on that EP7. I've seen on different notes that it is not possible to use XSS 2005 with ECC 5.0 as a back end. Is there any solution to