Will these stats allow a line reset if patient?
These are my stats, currently and of course I have had higher DL speeds over the last the last 8 months or so. I think I know what the replies will be and it maybe that my line cannot sustain a better connection and that the current stable one is preferable.
Solved!
Go to Solution.
I think it is your choice whether to remain with what appears to be a good stable connection with few errors for 13 days conencted or get noise margin reduced which will increase the conenction speed but may well increase the number or errors. The increased errors may make your line less stable and if so you first could try changing from fast to interleaved. it may be that if line stays like it is that it will automatically reset with a drop in noise margin without doing anything
I prefer stable but you may be happy with faster connection speed but some conenction drops - your choice
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.
Similar Messages
-
Will these five UPDATE ROUTINE lines accomplish the stated requirement?
Hi,
In an attempt to assign a source date field to a BW target field, based on the condition sourceA1 = A or B, I modified the update routine as follows and a syntax check reveals no errors:
$$ begin of 2nd part global - insert your code only below this line *
Data: V_CCCC D.
$$ begin of routine - insert your code only below this line -
IF ( SOURCE_FIELDS- sourceA1 = '002' or
SOURCE_FIELDS- sourceA1 = '012' ).
RESULT = V_CCCC.
If SY-SUBRC NE 0 .
EndIf.
ENDIF.
i. Will the above routine meet the stated requirement?
ii. So as it is now, what happens if sourceA1 is not '002' or '012'
iii. Any reason why the check error dis not report u201CRESULTu201D as unknown although it was not declared?
iv. Is there a better way of writing that I have above?
ThanksHi,
Your code will accomplish what you are looking for. It will assign the value V_CCC if your sourceA1 field is 002 or 012. If sourceA1 is not 002 or 012, the result field will not be filled.
If you want to clean up your code, you can use the following:
IF SOURCE_FIELDS- sourceA1 = '002' or
SOURCE_FIELDS- sourceA1 = '012'.
RESULT = V_CCCC.
ENDIF.
i. Will the above routine meet the stated requirement?
>as I understand your requirement .... yes!
ii. So as it is now, what happens if sourceA1 is not '002' or '012'
>result will be 0 or space depending on the data type.
iii. Any reason why the check error dis not report u201CRESULTu201D as unknown although it was not declared?
>Result doesn't need to be declared by you, SAP does that for you already.
iv. Is there a better way of writing that I have above?
If this is going into an ODS, you will overwrite non-002/012 values with a space, so be careful. If sourceA1 is not part of the key, you could be overwriting data with nulls.
Brian -
Neither our my kids iphones will allow them to purchse music or apps...it takes them to security questions which we tried to anwser but keep coming up wrong...will not allow me to reset them - help
iTunes Store Support
http://www.apple.com/emea/support/itunes/contact.html -
Hi - had issues with BB speed - ip profile was set to only 0.25mbps. BT did a line reset on Monday lunchtime. IP profile is still set ot 0.25mbps. Contacted BT who said it would take 10 days for the line to stabilise and spped will vary in that time.
Surely the IP Porfile should have been increased as part of the reset or will it automatically increase during the stabilisation period ? Normal speeds are 2-3mbps.
Thanksok got them
ADSL line status
Connection Information
Line state
Connected
Connection time
0 days, 00:03:12
Downstream
4,608 Kbps
Upstream
448 Kbps
ADSL Settings
VPI/VCI
0/38
Type
PPPoA
Modulation
G.992.1 Annex A
Latency type
Fast
Noise margin (Down/Up)
6.2 dB / 21.0 dB
Line attenuation (Down/Up)
47.0 dB / 29.0 dB
Output power (Down/Up)
7.0 dBm / 1.6 dBm
Loss of Framing (Local/Remote)
0 / 0
Loss of Signal (Local/Remote)
0 / 0
Loss of Power (Local/Remote)
0 / 0
FEC Errors (Down/Up)
0 / 0
CRC Errors (Down/Up)
0 / 0
HEC Errors (Down/Up)
0 / 0
Error Seconds (Local/Remote)
0 / 0
Hide Details -
Hello there,
I was just wondering if it was possible for an Openreach engineer to perform a line reset at all? If possible, it would be great to go back to the open profile I was on before and it was my fault to reboot the router several times during the stabilisation which obviously would have messed DLM up (which has put a major amount of interleaving on my line).
BT Home Hub Manager - Information for Helpdesk agents:
BTW Performance Test:
ADSL Checker:
Solved!
Go to Solution.you need an engineer visit before you will get a reset and from looking at your stats compared to your estimate I think that unlikley unless you can show you have a problem with your conenction and not just interleaving. if engineer visit and no fault you may get charged £129.99
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’. -
10 days training period after line reset
Hi,
So on Monday morning the engineer finally turned up and did line reset which in results I was getting my full speed (47.5/9). And very low pings 16ms to bbc.co.uk, abou 6ms on 1st hop but this morning hh5b decided to restart in results my ping went up by 12ms, now 28ms to bbc.co.uk and it decreased my speed by 3mb. Can anyone explain me how 10 days of training period works? I thought the router must stay stable for more than 10 days. Is it still training my line after router drop?
I suspect interleaving turned on on my line but why after only 2 days instead of 10 training days?
I have been told by engineer that I am very far away from the cabinet around 800m and that the line is working in 100% just after line reset and it wont stay like that.
Best regardsTonight I have noticed that I can't open any website (it takes about 3 minutes to open any website) and I am having a high packet loss on teamspeak3. The Noise Margin dropped from stable 6.0 to 4.5-5.0. It forces me to reboot my router but I don't want to, because my speed will drop and ping will go up occasionally. What can I do in that situation?
Some stats: -
My iPhone 4s will no longer allow others to send me a text message
My iPhone 4s will no longer allow others to initiate a text message with me. I think I have pin pointed the issue, but I don't know how to fix it. When I go to Settings - Messages - Send & Receive, it has both my phone number and my email but it only will allow me to check the email account. Therefore, if people don't have this email stored in their phone, then it won't allow them to initiate a text message to me. They can reply to my texts, but it comes up as my email address vs. my phone number. I have tried to reset my networks, but that didn't help either. I have not downloaded the new iOS 7.0.4 yet. Does that have something to do with it or how can I fix this because I'm on the road for business and I won't have a chance to download it until I get home on Sunday!
I'm sorry you have not been able to utilize your text messaging AlaynaFHirsch. I recommend downloading the new software to your phone. It will definitely help with functionality issues. Are you using a 3rd party messaging application? Have you tried to perform a restore on your account?
KinquanaH_VZW
Follow us on Twitter @vzwsupport -
my airport time capsule will no longer allow our iPhones or vizio smart tvs to connect to it, though my iPad air mac mini and mac air connect fine. Why is this? does a recent software update have anything to do with it?
What model is your TC? What is the firmware?
I recommend you do a factory reset and use short names.. not apple recommended names.
Short.. 2-20 characters .. less than 10 even better.
No spaces.
Pure alphanumeric.
Set fixed channels for 2.4ghz wireless.. test with 11, 6, 1 at least.
That often helps.. if not and is old, ie Gen1-4 go back to 7.6.1 firmware which is far more solid. -
I receive daily emails from the NY Times, which I read from my Ipad. Some of the emails will show all of the stories available, and some will only show a few lines in the body and the rest of the email is blank. Any ideas of what I need to do to fix this?
Try a reset: Simultaneously hold down the Home and On buttons until the device shuts down. Ignore the off slider if it appears. Once shut down is complete, if it doesn't restart on it own, turn the device back on using the On button. In some cases it also helps to double click the Home button and close all apps from the tray before doing the reset.
-
Line resets and stuck profiles (question not issue...
One of the mods in their calls to me mentioned that they are happy to do some line resets for me but want to avoid them too often since this caused the DLM to get concerned over the line status. [I have no reason to doubt this statement]
Now in my case what I sometimes could do with is getting a IP profile unstuck ie when it passed the point where it should have changed but has not and yes the BT system says that it did.
Is this the same thing as a line reset (which one would think it shoudl not really be) and if not can anyone confirm that this does not anger the DLM?
[the reason for asking is that normally my profile should go up within 24 hours at most which is bearable but recently it has stuck twice, ie BT says 1000 but speedtester and throughput showed 750].
If my post was helpful then please click on the Ratings star on the left-hand side If the the reply answers your question fully then please select ’Mark as Accepted Solution’To clarify, first the image is placed, then there is a rectangle over the image whose frame is slightly larger than the image frame, with transparent fill, and set the stroke to thick white with transparency lowered to induce the "reflection" sort of effect. Take a look at this screenshot: http://screencast.com/t/AYQDwx3g7w
Hope this helps.
Cheers
Parikshit -
I upgraded to Infinity about 6 months ago. The line speed never increased from what we'd had originally - we went from 5mb ADSL to ... 5mb Infinity.
I meant to complain and try and get it sorted but you all know that process and I just didn't have the time or the patience.
Anyway, so... two days ago we had a phone fault. Engineer comes out, finds the issue out in the woods and fixes it, no problem. However when he's testing our line before he goes, he sees our old data cable (from the wall to the router) and says it's not good enough. He says it's probably giving router issues and throttling our bandwidth.
I bought a new twisted pair data cable and whoomph, we jumped to 6mb just like that, and the ping has doubled in speed - browsing is lightning fast now.
But we are still WAY off what the Availability Checker said we'd achieve, and way off what the engineer said he *thinks* we should be getting based on his tests... He said MAXIMUM possible would be about 25mb, which in his experience suggested we should be looking at 15 - 18mb. He also said we may need a line reset before we see any real speed improvement (after replacing the cable).
6mb is great an all, and I'm not one to look a gift-horse in the mouth, but when I upgraded I was promised 12-18mb, and we're still way off that.
So, all that said and done... Should I ask for a Line Reset from BT, or will the speed likely increase automatically over the next few days?
Solved!
Go to Solution.your connection will recover but it could take a few weeks.
resetting you connection at present can only be done following an engineer visit so surprised engineer did not organise that before he left
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’. -
There are these weird gray growing lines going down the center of my iPod 4th gen what do i do?
I have had my iPod touch 4th gen for over a year now and i have these weird gray/green lines going down the center of the screen. They will not go away when i restart my iPod, and they only started when i came home from school and have kept growing please help!
Yo have hardware damage
Apple will exchange your iPod for a refurbished one for $199 for 64 GB 4G and $99 for the other 4Gs. They do not fix yours.
Apple - iPod Repair price
You can do it at an Apple store by making an appointment:
Apple Retail Store - Genius Bar
or send it in to Apple. See:
Apple - Support - iPod - Service FAQ -
When I try to use the Message feature on my iPad 2, to send a message to a friends iPhone (on iOS 5 too), why will it not allow me to send the message?
Check to make sure you are not typing your message in the Subject line. If you are, it won't let you send the message. Cut and paste the message into the Message field and you should be all set.
FYI, you can disable the Subject line from your messages in Settings/Messages. -
I have an iMac 5,1 with an Intel Core 2 Duo. I'd like to Lion, in order to use iCloud, but the specs indicate I don't have enough memory. How much memory can I add? And will this upgrade allow me to install Lion?
I believe your model iMac can address 3 GB RAM; the minimum for Lion is 2 GB - however, that is an absolute minimum for very light use. You would be much happier with a minimum of 4 GB.
http://www.everymac.com/systems/apple/imac/stats/imac-core-2-duo-2.16-20-inch-sp ecs.html
(You can install 4 GB, but it will only be able to address about 3.1 - 3.2 GB) -
Can i get a line reset? upload speed has dropped
Hey there, is it possible to get a fresh line reset? a friend of mine is on the same cabinet as me and im at 5 mb upload hes at 15. I prefer upload to download as i upload alot of videos so every little helps! i used to get over 10 mb upload but slowly its going down and down
Can you run this checker and post back a screen shot of the results
http://www.dslchecker.bt.com/adsl/adslchecker.welcome
and use this speed tester then carry out the further diagnostics and post back a screen shot of all the results including your IP profile for up and down. This test must be done with a wired connection.
http://speedtest.btwholesale.com/
if you have a Homehub 5 can you also post the stats from 1-12 by logging onto the home hub management pages then troubleshooting > help desk. http://bthomehub.home/
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’
Maybe you are looking for
-
Dual Channel memory problems on Neo 875P
I am having considerable trouble getting the NEO 875P to work with dual channel DDR400 DIMMs. I have two Kingston KVR400X64C25 DDR400 256MB memory modules, each of which works correctly by itself. However, once I move one of the modules to channel B,
-
Report Painter Report Performance Issue
hi, My client facing the problem with Report painter reports , almost all the reports taking much amount of time to execute . we are Using 5.0 version tables FAGLFLEXT and CSSS . i have some doubts report index is the cause for this or any other reas
-
Am I the only person that feels like the salesman lied to me, wrote up contract wrong, etc?
I had purchased two Iphone 4's without contract and enjoyed not having the bill and extra fees every month. Through the prepaid carrier, my son and I didn't even know we could use a laptop or anything with our phones. Luck would have it, the only
-
Using a URL parameter in SQL Query
Newbie question... I have been developing a dashboard application, and I have been using input bind variables in the SQL. That all works fine. What I would like to do is to have a user go to a page via a URL with paramaters like this: http://atlas:77
-
ITunes v5.0.1.4 plays Only First 10 Seconds
I have valid mp3's that play completely without issues in Quicktime and Winamp. If I begin one of these mp3's in iTunes, it will only play the first 10 seconds and then skip to the next song. Interestingly, if I skip ahead in the same song (before 10