Win 98SE Startup Logon Problem

All our Win 98SE had the startup logon problem when we migrated to Cisco 1240AP. Previously, we don't had this problem when we are still using the SMC AP.
When we want to login to windows 2000 Domain during startup, the system will complain that it can't find a DC and we had to click ok to proceed. Once login, we can see that it can detect the AP with good signal strength. Then we need to logoff and then only we can login to the Domain without any problem.
But when we restart the system to login to the Domain again, the same problem occurs. Only when you click ok to login without network and then logoff again to login without restart the system, then the PC can find the Domain and login without problem. All our PCs are using the static IP assignment with DNS and WINS configure.
We are currently using the DLink client wireless adapter and we had try to change to Belkin client wireless adapter with more recent Win98 driver but with the same problem.
Our Window XP don't had this issue. As i had said, previously when we are using a SMC AP, we don't had this problem.
Anyone here had the same problem that had a solution ?
Thanks.
CMYip

Yes. The solution was to upgrade to upgrade the customer's laptops to WinXP.
(Drive mappings were also a related issue).

Similar Messages

Dual Boot,XP Pro Ok but Win 98SE cannot boot

I have a dual boot system, with 2 primary partitions, and bootmagic installed. My boot disk is on raid 0 on the raptor drives.
Installed Win 98SE first, than created second primary partition, installed win xp pro. Installed bootmagic on 1st primary partition, so can dual boot.
XP installed and running without any problem. XP runs fine with either ACPI enabled or disabled.
For Win 98 SE, with ACPI disabled, with USB enabled, system hangs while booting up. If I disable USB, I can boot to win 98 SE. During initial install, the first drivers for my board was the Intel INF. I suspected the board and brought the board to local tech support. They showed me that they could install win 98 SE without any problem. Board, cpu, hsf and rams were the mine. They used a single hard disk and a single CD Rom. Therefore, cannot RMA board.
I am suspecting that because I am using the Promise and Intel Raid, more irqs had to be shared and XP Pro could handle that but Windows 98 SE cannot handle that. I only have three add on boards, the Storm 2 DV editing card, ATI AGP graphics card and a V.92 modem card. Nothing else. I tried to do some fiddling in the bios for the IRQs but does not help. The only way to boot into Win 98 SE was to disable USB.
Could someone give me some pointers on what I could try out further?
Thank you.

I had rewritten the information regarding my problem and added in more detail and sent it out to MSI. Hopefully, they will respond (quite unlikely) . Here's it:
I have a dual boot system, with 2 primary partitions, and bootmagic installed. My boot disk is on raid 0 on the raptor drives.
Installed Win 98 SE first, than created second primary partition, installed win xp pro. Installed bootmagic on 1st primary partition, so can dual boot.
XP installed and running without any problem. XP runs fine with either APIC enabled or disabled.
For Win 98 SE, with APIC disabled, with USB enabled, system hangs while booting up. If I disable USB, I can boot to win 98 SE but my Intel Gigabit Ethernet will have an exclamation mark. Getting newer drivers and Intel INF did not help. During initial install, the first drivers for my board was the Intel INF. I suspected the board and brought the board to local tech support. They showed me that they could install win 98 SE without any problem. Board, cpu, hsf and rams were the mine. They used a single hard disk and a single CD Rom. Therefore, cannot RMA board.
I decided to disable the Intel Gigabit Ethernet in Win 98 SE. After that, I looked into the properties and realized that some memory allocated for the Intel Gigabit Ethernet are being used by other system resources. If I disable Serial Comm Port 2 and enable USB in bios, I can boot into windows and drivers detection for USB will proceed until it gets to “ Intel ® 82801EB USB Universal Host Controller – 24D7 “ and hangs my system. I cannot check if the problem is caused by IRQs or Memory allocation.
I am suspecting that because I am using the Promise and Intel Raid, more irqs had to be shared, memory allocations were more demanding and XP Pro could handle that but Windows 98 SE cannot handle that. When I try to do some tweaking in Windows 98 SE properties for the Intel Gigabit Ethernet, I was prompted that I cannot make changes. I guess the board, at bios level, fixed all the irq and memory allocations and so Windows 98 SE cannot make any changes.
Anyone can advise what I can do within the bios so that I can do further tweaking on memory resources allocation? I know that I can do something on IRQ and DMA but seems nothing can be done for memory allocation.
Hope one of you have some helpful information.

Ovi Suite isn't minimised on Win XP startup

Hi,
I've just installed Ovi Suite (2.0.1.35) on to my system running XP. Unfortunately, every time my system starts up, Ovi Suite pops up, which is really annoying. Previous versions did not do this at startup. Does anybody know how this problem can be fixed? There's nothing obvious in the preferences.

Hi,
Do you have two complaints from your post? Title read as
(1) Ovi Suite isn't minimised on Win XP startup
(2) I've just installed Ovi Suite (2.0.1.35) on to my system running XP. Unfortunately, every time my system starts up, Ovi Suite pops up, which is really annoying. Previous versions did not do this at startup. Does anybody know how this problem can be fixed? There's nothing obvious in the preferences.
For your title issue, you can give complete details about your PC
For your second issue, Could you please check on Nokia OVI Suite 2.0, Tools > Options > General > Start up
Start Nokia Ovi Suite automatically when your computer starts up
If yes, and if you dont want it to start up automatically, unselect this option

FF4 sort of works in Win 98SE via Kernel Ex but slow and lacks features

I had last version of FF2 working fine with Win 98SE but could not access features using java, Flash, etc.; I installed Kernel EX and FF4, after which it seems to work but is slow as molasses...takes more than a minute to load home page or other link, after which it won't scroll for 10 to 30 seconds. There is no history or bookmarks and the back/forward buttons do not work consistently.
It works well enough to be promising, but frustrating; is there any hope? Perhaps missing system files from Win XP? Any help greatly appreciated...I really like Firefox!

Sorry, your operating system has been officially obsolete since July 11, 2006. It's likely that websites require more recent versions of Flash Player and Java than you can run.
* [http://kb2.adobe.com/cps/406/kb406791.html Flash Player 9 for older operating systems]
* [http://java.com/en/download/faq/other_jreversions.xml Where can I get older versions of Java and related documentation?]
You can try starting Firefox in a new profile and see if that helps any. But it's likely that these problems are caused by running Firefox on an unsupported operating system with the aid of third-party software. Having an overclocked CPU doesn't help matters either.
* [[Managing profiles]]
If things aren't any better in a new profile, you can try Firefox 3.6.28 instead. This version is now obsolete and insecure, but that seems a bit of a moot point in your case.
* [http://www.mozilla.org/firefox/all-older.html www.mozilla.org/firefox/all-older.html]
If you're unable to upgrade your hardware, you may want to consider switching from Windows to Linux. You would have the benefit of an up-to-date and secure operating system, browser and plug-ins at no cost.
* [http://lubuntu.net/ http://lubuntu.net/]

Usb km2m Win 98se

I don't know if anyone is still using Win 98se on a km2m. But I got my usb key working on this combination the other day for the first time ever. I'm not sure why it worked this time, having refused countless times in the past. But I can recount the context.
I happened to insert the key just after doing a hotsync to a Palm Zire. (Which also happens to have problems, associated or not with usb I don't know.) There were, I realised later, two instances of Palm's hotsync in memory - it had crashed twice during operation.
Windows installed the usb drivers (which I had uninstalled as of no use) and, miracle, a 2-click on the icon showed the files on the thumb drive, no problem.
Since then, it's worked normally, without hotsync. But there's a pair of fingers crossed ..
jorex

Thanks for the replies.
> USB key's are regularly sold without software although this is required for Win98 operating system. Download drivers from the manufacturers website.
Done that, umpteen times
> Tell me the specific problem you have with the Palm Zire and I can maybe help with this.
Hotsync doesn't work when launched from the zire, only from the pc.
> Have you tried entering SafeMode, to
> 1 Have a look for (disturbing) superfluous instances of USB-devices?
> 2 Installing the mobo drivers for USB, esp. 2.0.
Yes, I've downloaded drivers from msi, from the usb key maker, I've cleaned up in safe mode .. countless times.
The point is that it's working now. No problem.
jorex

Moderate success w/Win 98SE

It has now been a few months of jacking around with my @nywhere Master, and I'm almost happy with the results. I finally have it running crash and error free!
I'm posting to possibly help others, especially Win 98SE users.
What a ride! Numerous installs, much time searching this forum. This card is like a plague around the world. I never gave up because I didn't want to invest in another, and I'm hopeful that one day we'll all have an incredible program to run it.
I will tell you that this is a nice tuner, proven daily by the 10 foot high-quality picture it shows on my wall.
The different installs each provided different results, even including the dreaded "Taliban Attack", where the settings always revert back to Antenna in Aphganistan. ("Taliban Attack" is a quote from another user in this forum awhile ago).
Here's how I have it working now;
Latest Detonator drivers for my MSI FX-5200 128TDR, for which I always lose my Stereo viewing capabilities. Oh well, maybe someday I'll find the right drivers to play games with my 3-D glasses again.
Latest TV Tuner drivers from MSI website, 8606 v.2.79.1.65.
MSIPVS, old, from bundled disc, filename version 6,02,100,1247.
After the MSIPVS software installed, the radio tuner driver was automatically installed from the disc. I haven't tried the radio, it probably works.
NO Winproducer, Wincoder! That disc is trash, I think.
So now when I click on the MSIPVS icon, it fires right up with no problems. All channels are in stereo,(finally, the settings stay!), records the way it should,(WOW!), and plays back without incident. Takes good snapshots, too. I haven't tried the aud/vid capture yet, I'm hopeful.
The downside is that I've NEVER seen the remote work, nor the one that came with the FX-5200. Maybe someday, but for now I use a Gyration cordless keyboard and mouse for channels, volume, brightness, etc., in my home theater.
I hope this may help, I can elaborate more if requested. Good Luck!!

hi
did you turn them on in bios ?
page 3 19 manual

Logon Problems? Get support is not working in Portal logon Page

Hi Experts,
I have created A Role and assigned Logon_help action to it and assigned the Role to Anonymous group.
So i have Logon Problem? Get Support link on Portal Logon Screen. When i click on it, i was asked to provide userid and email id.
I have entered them. i got a message the my userid is reset and sent to my mail. but havent received any mail, and the password is changed which have to log in as admin and reset the password.
Help me this regards.
Thank you
Siva

you might not have correctly configured your mail servers....
refer below link
http://help.sap.com/saphelp_nw70/helpdata/en/89/c5fd430b63c74bbdfaa5f2ec9bb20b/content.htm
http://help.sap.com/saphelp_nw70/helpdata/en/44/0761cea5c610b3e10000000a11466f/frameset.htm

7.01 to 7.3 Upgrade - Logon Screen - "Logon Problems? Get Support" occuring

Hi
We have upgrade our ABAP and JAVA stacks from NW 7.01 to NW 7.3.
After the upgrade is the "Logon Problems? Get Support" occuring on our portals logon screen. In 7.01 this was controlled with the parameter ume.logon.logon_help - however after the upgrade we do not see this parameter anymore.
Screen dump (requires a couple of clicks)
http://www.filefactory.com/file/c26d20b/n/Portal_Logon_Page_Issue.jpg
Any idea about how we remove the "Logon Problems? Get Support" part?
Thanks and kind regards,
Torben

Hi Torben,
On my fresh 7.3 installation, everything is clean and ... fresh ...
So, for example, the built in group AnonUsers only has the user Guest as it's solely relation (no parent, no child groups); the guest user has the Guest role, which has (via it's groups) roles Everyone and Guest; onbly the role Everyone as got UME actions.
All together, this sounds much like an upgrade issue (on my fresh 7.3, there is no group "J2EE_GUEST" at all).
Two possibilities to go:
- Open an OSS message (should be done in any case probably, to report this issue to SAP, so that this can be fixed);
- Check the UME consistenty by yourself (http://help.sap.com/saphelp_nw73/helpdata/en/44/aecb4253217037e10000000a422035/frameset.htm)
Maybe the second point already will fix some things; would be great for you, anyhow, I still would advise to report this issue officially to SAP.
Hope it helps
Detlev

Notification Mail is not working for other logon problem link

Hi All,
When we are submitting other logon problem details then administrator is not able to get any E-Mail notification,
whereas when we are using password reset then we are able to get E-mail notification with new password.
we are using EP6 and we have given ume.notification.admin_email= with some administrator id.
in case of password rest we are getting the mail from the same id which we have given there.
Regards
Trilochan

Hi,
There are two ways of doing this: either through Visual Administrator or through Config Tool using offline mode. My guess is that if you are doing it through Vis. Admin, then there is a possibility that the settings are being lost. Have you tried it through Configtool?
Make sure the procedure that you are following is as follows:
1.      Start the Config Tool by executing j2eeconfigtoolconfigtool.bat.
2.      In the tree, navigate to Global server configuration ® services ® com.sap.security.core.ume.service.
The list of UME properties appears.
    a.        To change the value of a property:
       i.       Select the property in the list.
      ii.       In Value at the bottom of the screen, enter the new value that you want to assign to the property.
      iii.       Choose Set.
      iv.       Choose (Apply changes).
b.     To restore a property to its default value:
       i.       Select the property in the list.
      ii.       Choose Restore to default.
     iii.       Choose (Apply changes).
c.      To restore all properties to their default values:
      i.       Choose Restore all to default.
3.      Restart the nodes in the cluster for the changes to take effect.
Regards,
Shitij

Firmware version 8.00.2 for WRT54G on a Win 98SE system

I tried to download the 8.00.2 firmware for the WRT54G on my Win 98SE computer, which is hardwired into the router. I had the laptops with Win XE or with Mac op sys shut down so they would not access the router. I downloaded a file with the extension *.bin. Neither WinZip mor PKZip could expand that file. When I double-clicked the file, I got asked what program to use to open the file. Please advise on how to use the downloaded file on a Win 98SE system.
Also, when I tried to download the users manual and the info sheet for this router, I got a blank screen. I'd love to see these.
Thanks for any help.

To upgrade a routers firmware, open up Internet Explorer 1st, then on the address bar, type the numbers 192.168.1.1 (username just leave it blank, password as a default is admin). Then go to the Administration tab, go to firmware upgrade, browse, and select the file that you downloaded (the one w/ the .bin extension).

How i instal adobe reader in my dell 1011 mini notebook. showing error i try in win xp win 7 win 8. but same problem

how i instal adobe reader in my dell 1011 mini notebook. showing error i try in win xp win 7 win 8. but same problem.
when i want to instal, go %40 60% and stop. machine hang no finish option show no stop.

Try the installer from http://get.adobe.com/reader/enterprise/
If that does not solve your problem, please provide the full and exact error message.

Other Logon Problems

Page:Having trouble logging in ?
This page has two option
1.Password Reset
2.Other Logon Problems
Link 1 password reset is working fine and mail are also going to user but other logon problems does not send mail to administrator.
I have searched sdn on following points
1.ume.user_logon_problem_request but this property does not exist in direct editing if i apply this and click on save changes , changes are lost.
2.checked email option part in notification email.
3. I am working on EP6.0 SP2 verstion.
<b>Note : I am not recieving message "E-mail with logon problem sent to administrator" by clicking on submit button on other logon problem page.</b>
Can anybody comment on this ?
Regards,
Hemant

Hi try this page on help.sap.com:
http://help.sap.com/saphelp_ep60sp2/helpdata/en/d1/956f8b86b2a949913ed22d253e0012/frameset.htm
Enter the property there and restart the portal.
Regards,
Kai

Customizing logon problems page

Hi,
I'm working on EP 7.0 ,my logon problems page is not enabled ,plz help me how to configure it

HI
authschemes.xml file change the com.sap.poratl.runtime.logon with your par file name
This blog explains step by step procedure for Custumzing the Portal Logon Screen
Modifying The Logon Par(or customising the Logon Screen)
A fast and easy Portal logon page customizing
Portal Customizations Intro - Login Part 2
Portal Customizations Intro - Login Part 1
http://help.sap.com/saphelp_nw2004s/helpdata/en/23/c0e240beb0702ae10000000a155106/frameset.htm
Hope this helps,
Regards,
Arun

MSI KT3 Ultra 2/Win 98SE/ USB Root Hub

Please, could someone help me to understand if I have the correct installation of drivers for USB
for Win 98SE?
Having installed the USB 2.0 driver from the M/B disk
Under Device Manger > Universal Serial Bus Controller,
I have the following entries:
1x USB 2.0 Root Hub
3x USB Root Hub
1x Via PCI to USB enhanced Host Controller
3x Via Tech 3038 PCI to USB Universal Host Controller
My M/B Bios version is 5.5 and I have enabled all USB ports (6) in the Bios.

Hi,
You don't need to connect USBOC....
As for the other pins, you have to rewire them....
Take an Ohm-meter and measure them against a normal USB connector.....
Don't connect it just like that......

Updated itunes to 11.3 on win 7 but had problems. so reinstalled itunes 11.2 but now itunes won't recognize or sync my touch 3 with 5.1.

updated itunes to 11.3 on win 7 but had problems. so reinstalled itunes 11.2 but now itunes won't recognize or sync my touch 3 with 5.1. did all the recommended fixes, appears have correct driver, all necessary itunes programs, etc. still won't work. help!

For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
tt2

Win 98SE Startup Logon Problem

Similar Messages

Maybe you are looking for