Win XP does not boot

Well, i have a problem with a MSI K8N Neo2 Platinum, when i'm installing Win XP, i can boot from the CD, the wizard run perfectly, after all the machine reboot like it should, but the OS won't boot, it is a problem with XP, because Linux SUSE 9.2 Pro work perfectly, i tried installing Win ME and it does Boot, i have the problem only with Win XP and the four leds are green, so the OS is the problem, sometimes when i use the linux loader or something like that to run XP a message show and it says that the OS couldn't load. BTW i tried with and without any OS previously installed.
Athlon 64 3000+
IDE WD 80GB, 8 MB buffer
512 MB, Crucial DDR400 RAM
ANTEC TruePower 480.
should i change my HD for a SATA?

I Apologize to those I've quoted, I forgot to paste your names, but I quoted you so these are not my suggestions.
read this
"Hello,
I have had this problem before, it might be the same thing for you.
If the BIOS sets the drive in CHS mode windows will get this message.
You must enter the BIOS,
Standard CMOS setup, choose your hard drive, set the MODE to LBA.
Save and exit,
Then you must format the drive, let windows setup format it.
Does this solve your problem?"
Boot order/priority seem to be an issue too.
" had exactly the same error as you have,
& it was the MBR that was borked up..
Partitioning,formatting..nothing helped
Used Maxblast from maxtor's website
to create a new MBR and low level format..
& voila..fixed
So I suggest you search on the site of your
HD manufacturer for a similar tool and give
it a try
grtz"
read this too
"if not for now but for future ref the following may be useful
"Operating System Not Found" or "Missing operating system" error message when you start your Windows XP-based computer
the Cause should sound vaguely Familiar
Quote
CAUSE
This issue may occur if one or more of the following conditions are true:
The basic input/output system (BIOS) does not detect the hard disk.
The hard disk is damaged.
Sector 0 of the physical hard disk drive has an incorrect or malformed Master Boot Record (MBR).
Note Some third-party programs or disk corruption can damage an MBR.
An incompatible partition is marked as Active.
A partition that contains the MBR is no longer active
as dacull pointed out its always key to check the Hard disk boot priority 1st at any non boot.
by using the windows XP CD & booting from cd you can open the recovery console and repair an installation, including the MBR. Links on using the recovery console are in the above article.
luck"
"Hi all,
I also had this problem when I was running PATA and SATA drive. If you have a PATA drive connected and you are installing to the SATA drive, windows will write the boot files to the PATA drive and the rest to the SATA drive. Once install ends set the PATA drive first in order and it should work fine.
But what I do is just disconnect the PATA drive(s) and only have my SATA drive(s) and windows will install all to them and after reboot just reconnect the PATA drive(s).
This is what I have found with windows XP.
Hope this helps,
Andrew"
The above happens whenever you're working with two drives and the one you're installing windows on isn't the first from what I've read.
"I think the reason it is quite important to check this is because if you have the order like this
1) Non bootable ATA disk
2) Bootable SATA disk
the boot will totally fail! (Its a bug in the BIOS sigh)
It should look at disk 1 , find its not bootable, then look at disk 2, but it doesn't do that in that combination. "

Similar Messages

Satellite A105 WIN XP does not boot or load...

Ok, so my wife's laptop has a boot issue. Model is A105-S4284
The Toshiba/Phoenix screen loads, but does not boot/load XP. It gives a black screen, then sits for a few secs and restarts. it will continue this loop indefinetely as far as I can tell. When this happened, she complained that it has been taking longer for it to boot into XP recently. (Wish she had told me before)
I can get to BIOS system utilites, Boot menu, and can access F8/Win Advanced options boot choices. I have tried the following:
Safe Mode
Safe Mode w/command prompt
Last known GCFG
Disable Auto restart on failure
I have also done a battery pull and unseated the memory, even swapping left/right, and attempted boot from just one mempry module, all with no change.
Apparently her DVD/optical drive is toast (apparently has been) so I can't do a recovery disc, but I did make a recovery USB drive. No dice there either.
What have I not done? Since I can access the adv. opt. menu it seems winXP is still there. most likely she shut it down while XP was installing something, and now there is some type of error in the registry or somewhere, but I can't seem to recall or remember what my next steps would be to gain access to I can try to clean it up and recover.
I would do a complete wipe and start from scratch, but her entire work portfolio is on the HDD and she (foolishly) has not backed it up, at least not recently. Is my best bet to get an outboard drive enclosure and set the jumpers to slave, so I can attempt to recover the data that way?
I'm a bit stubborn, and know my way around a computer, and I refuse to give up and drop it off at the geek squad.
Please help!

Satellite A105-S4284
her entire work portfolio is on the HDD
First things first. You should rescue the files.
Remove the hard drive and place it in an enclosure accessible from a desktop via USB.
-Jerry

Win 7 does not boot up on Satellite

So last night I was using my Toshiba Satellite laptop.
I don't know many specifics because i'm not very good with laptops. Here is where the problems starts.
So after I finished I shut it down.
The next morning I wake up, it wouldn't start windows.
I'm currently using windows 7. So anyways it tells me to shut down. I boot it again and then it only gives me 2 options: startup repair or run windows normally.
When i try run windows normally it says "starting windows" but it never boots.
Then when i try startup repair it goes to attempting repairs and i've been doing that for 8 hours and no luck. it says a recent hardware or software removal may have cause it. But i've had nothing plugged in except the charger.
I REALLY WANT TO USE MY LAPTOP D:
CAN SOMEONE PLEASE HELP MEEEEEEE??!!

> I'm currently using windows 7. So anyways it tells me to shut down. I boot it again and then it only gives me 2 options: startup repair or run windows normally. When i try run windows normally it says "starting windows" but it never boots.
It looks like the Windows OS was muddled up Im not quite sure why but such things happens simply
However, you can try to recover the notebook using the HDD recovery option. But this will work only, if you didnt format the HDD and didnt delete the HDD recovery partition.
So try to power up the unit, press F8, choose repair my computer and then choose Toshiba recovery.
Note; this will format the currently system partition which means that you will lose the files on the C partition.

Toshiba Satellite P870 upgraded to Win 8.1 does not boot

I have a Toshiba Satellite P870 with Win 8 preinstalled. Soon after upgrade to Win 8.1 and basically successful removal of “watermark error” (secure boot activated) the machine stopped booting completely: after pressing the power button ventilator sound
is heard with periodically changing loudness as well as clicking sound from the speakers. The screen stays black. Attempts to start the PC through pressing F2 or zero buttons did not produce any result. Neither did I succeed with recovery discs I created before:
the system simply does not boot from the disk. It looks like I tried all options offered by Microsoft and Toshiba. I would be happy to roll back to factory settings.
Could someone give me hint what to do next?

Hi,
For the issue, let us know how to remove the “watermark error".
Meanwhile, I would like to confirm if you could access the BIOS.
I suggest you update the BIOS version to test it.
If you want to repair the startup issue, you should use windows 8.1 recovery discs or installation discs.
Meanwhile, if you cannot access the BIOS, it may be caused by hardware, I suggest you contact the Toshiba manufacturer for further help.
http://support.toshiba.com/
Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact
information.
Regards,
Kelvin hsu
TechNet Community Support

Satellite M30-107 does not boot correctly after Recovery disk usage

Hi
I've recently got hold of a second hand toshiba Satellite M30-107 laptop, and decided to freshen it up.
I used the toshiba recovery disk, but after doing so the laptop no longer loads windows.
When turned on it shows the Toshiba start up disk for about a second then goes to a blank screen and freezes.
When turned off and on again a screen comes up reporting an error in shutting down and gives the options to start in safe mode etc. but choosing any of the options causes the machine to freeze.
Any help or advice would be much appreciated.
Thanks
jt

Hi
Sounds a little bit like the notebook does not boot due to the Windows software issue
Did you recover the M30 with the original Toshiba recovery CD which was supplied with this M30 unit?
Maybe Im wrong but for me it looks like a wrong recovery CD was used and an image with non compatible drivers was installed
You could try to install the OS from original Microsoft Win XP CD and could check if it would be possible to get the notebook ruining using clean OS.
In such case we ( you and me ;) ) could find out if this issue could be related to the software or hardware.
Bye

HP Z620 does not boot when external Seagate hard drive is connected

I'm troubleshooting an HP Z620 workstation with 32GB RAM, one 500GB HDD + one 1TB HDD running Win 7 Enterprise 64 bits, this user has 2 external USB 3.0 HDDs, one Buffalo 2TB + one Seagate Desktop Backup Plus 4TB; the problem comes when the external Seagate HDD is connected and the PC is turned one, for some reason the PC does not boots, it shows a message that states "Non-disk or no boot disk error" and sometimes it tries to boot, but then goes thru the "Windows repair option" or "Start Windows normally" routine, none of these results on starting the PC.
The only way this PC starts and works properly is when PC is started with the external Seagate HDD disconnected and then connected once the Win 7 is up and running; the problem described above does not happens with the external Buffalo 2TB HDD and the Seagate HDD have been tested throughly and no errors or problems have been detected on it.
I'll really appreciate your attention to this, as well as your prompt response.
Regards,
Gaspar Campos

Hi:
You may also want to post your question on the HP Business Support Forum -- z Workstations section where there may be more folks familiar with that issue.
http://h30499.www3.hp.com/t5/Workstations-z-series-xw-series/bd-p/bsc-272#.U1k4uv1OXGg

Hyper-v Client in Win10 Enterprise Technical Preview does not boot to PXE via Leagacy Network Adapter after OS is installed using gen 1 BIOS

Using Hyper-v within Windows 10 Enterprise Technical Preview to boot a Win 7 Legacy BIOS (Generation 1) Operating system client does not boot to PXE legacy network adapter after operating system has been installed within the Virtual Client.
Hyper-v Client will boot to PXE Legacy Network Adapter only when no other boot device is available and no OS is installed.
Hyper-V settings seem to ignore BIOS - Startup order within Hyper-V Client Settings and will always boot to VHD before Legacy Network Adapter even if Legacy Network adapter is first in the startup list.
IF VHD is deleted and a new VHD added to the Client then will boot to PXE using Legacy Network Adapter. Again once OS is installed then will not boot to PXE Legacy Network Adapater.
Gen 2 BIOS/UEFI works as expected and boots to PXE network everytime.

Hi shaunmoncrieff,
Thank you for the information.
Currently I am not available to take a test using Windows 10 on physical machine.
You may try to submit this information through Windows Feedback Tool, once I have tested, I will update the results here.
Best regards
Michael Shao
TechNet Community Support

New MBP i5 does not boot after hard disk swap

Hi there,
I received my new i5 MBP today. After booting it once with the installed HDD to check if it's ok, I exchanged the hard disk for the one in my Late 2008 Macbook Pro. After doing this, my Late 2008 Macbook Pro boots fine with the (new) hard disk from the new i5 MBP, but the i5 MBP does not boot with my old hard disk.
To give you some details:
- I have installed 10.6.3 on the (old) hard disk that's not booting.
- The i5 MBP boots fine from the installation DVD
- Disk utility finds and can read my hard disk, no errors
- PRAM NVRAM reset did not help
- when booting in safe mode, I can see the system stop booting after or while loading Extensions.mkext
My guess is, it tries to boot and load the wrong Extensions for the new system (CPU? GPU?). I have no idea how to fix this.
Any help would be greatly appreciated!

Focx,
Welcome to Apple Discussions.
Inserting the drive from an earlier model MBP will probably not work. The version of the system you have on that HD is designed for earlier hardware so when you put in in your new machine it's going to be recognized. What I'd recommend is re-installing the disk that came with the new machine and of course putting the 2008's disk back in the old machine. Then use Migration Assistant on the new machine and migrate your data from the old machine into the new machine.
This will provide a much more stable system and should work just fine.
Regards,
Roger

Satellite L745D-S4214 Does not boot; HDD recovery partition not working

I tried to apply the recent windows 7 updates and my laptop no longer boots. I tried to press F12 and select the HDD Recovery partition, but it does not boot regardless. There is a message that it does not communicate to a specific device. I believe the address called out was 0xc0000e9, but I am going by memory. I never created a recovery CD because I thought I was covered by the HDD partitions. This was purchased on 10/26/2012, so it should still be under warranty.
PLEASE HELP!

Hi I'm going to assume that your recovery works like mine and that the recovery partition is still good and not corrupted.
Shut down your PC. Press F12 and select HDD recovery. Click enter. This should start the recovery from the hidden recovery partition.
PS I would advise you to make the recovery discs or USB recovery Try this first.
Perform a power cycle
Even when your laptop is off and unplugged, residual power can still be held in some components. While this is normal, clearing it can help with boot problems. Perform these steps to complete what’s called a power cycle.
Ensure the laptop is turned off.
Unplug the laptop's AC power cable.
Remove the battery (if the model has a removable battery).
Unplug all wires or peripherals. This includes CDs, DVDs, USB sticks, mice, printers, and any other accessories.
Hold down the power button for thirty seconds.
Reattach the battery.
Connect the AC adaptor to the power socket that was confirmed to be working in the first step.
Connect the other end of the AC adaptor to your computer.
Try starting the computer.
If your laptop starts normally now, you're done!
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.

X102e - Hard drive does not boot into Windows

Hi, I was trying to reinstall Windows on my X120e.
I tried clean install with Windows 7 Professional, but the hard drive does not boot into the Windows once it has done the first phase of the install(you know, the copying part)
After the restart done by Windows, it goes as far as "Starting Windows" but does not actually boot into the Windows.
When I try to install Windows with another HDD, the device works well, but I can't swap the HDD because it is not 7.5mm think HDD.
Is there any possibility the HDD will work trough any software-level process? The HDD works fine as external HDD when tested with external HDD adapter, and installs well. only problem is that it fails to boot
Kim
W540( ), Helix(Sold), Tablet 2(Sold) Tablet 2( ), X120e(Sold), X201 Tablet, X41 Tablet(Sold), X41, X32*4, 701C*4

Thank you for reply.
This is not exactly the issue. I was talking about the HDD originally installed in the PC.
The PC successfully recognizes the external disk I used to install the Windows, but the problem was that I did not boot into the "First boot" screen, which basically works on the already installed data.
As of now I have installed an SSD and is working fine. strange part is that HDD works just fine when I use it as an external HDD via adapter. Strange huh?
Kim
W540( ), Helix(Sold), Tablet 2(Sold) Tablet 2( ), X120e(Sold), X201 Tablet, X41 Tablet(Sold), X41, X32*4, 701C*4

Reset Password - System does not boot from DVD

My System: Macbook Pro - 2Ghz Intel Core Duo - OS X - 10.6.8
Hi everyone,
i forgot my password. So i want to boot from install DVD to reset the password. Unfortunately my macbook pro does not boot from DVD (10.6.3).
I press c all the time...but sometimes the macbook pro throws the DVD out...and sometimes nothing happens.
The DVD drive is working fine...
Any other idea?
Thanks in advance.
Fabian

So when you boot holding option it shows a padlock with a password field? Is that correct?
In that case we're talking about the firmware password, which you can't reset via the install disk. There is only one way to do this, I'm not certain if one is allowed to divulge that information publicly - might want to try googling "reset firmware password"

Macbook pro does not boot after upgrading ram

I have a macbook pro late 2011 which runs with mavericks operating system . I have tried to upgrade my macbook to 8Gb. Macbook does not boot when the two ram slots are filled with 4GB ram but runs well when the slots are filled with 2GB ram. When i try them individually with one slot of 2GB ram and another slot with 4GB they run perfectly which shows status ok in the RAM info. What could be the problem .

Around here, most of us recommend only Crucial and OWC for RAM because it's guaranteed to work with Macs and it's what most of us have. If I were you, I would return the RAM and look at purchasing RAM from either Crucial or OWC. If you can't get their RAM to work then you'll know that there's some trouble with your actual slots.
Good luck,
Clinton
MacBook Pro (15-inch Late 2011), OS Mavericks 10.9.4, 16GB Crucial RAM, Crucial M500 960GB SSD, 27” Apple Thunderbolt Display

KT6V + sempron 2800 does not boot when BIOS saved

Hi,
I have just bought a new sempron 2800 to be use on a KT6V LSR. I plugget in my KT6V but was not recognised well (but all was working ok with windows). To be recognised, I have flashed with the last bios of MSI my motherboard... and now I have the following problem:
- I clear CMOS, then boot. It comes ok (processor detected and set a 1200Mhz)
- Then CMOS has a bad checksum: I enter setup, then load default, save.
- I reboot: the computer does not boot up.
If I re-clear CMOS I can re-enter setup and modify frequencies or other options. But when I save my modifications, then the computer does not reboot anymore (I have to re-clear cmos again)...
I tried to apply the configuation I found in this thread:
http://forums.amd.com/lofiversion/index.php/t69536.html
It says that SDRAM must be at 333, FSB at 166 and multiplicator at 12. When applying this settings, it does not boot (the leds indicate that the chipset initialisation (the first step) does not pass).
If I just load biios default, the leds indicates that it fails when checking the memory (second step of boot). I suspect that it's a problem of memory (but my memory was working well before !): it's 2x512 of DDR 400.
Any suggestion is appreciated :D . I spent several hours trying to configure the bios but it does not boot..
(I'll also try to find help on AMD forums...)
(Some extra info: my PSU is 26A for 12V, so it seems that it's not due to the PSU (as I read in the FAQ of this forum).
Thanks,
Ptitmain.

AMD Geode™ NX Processor Family & DB1500 Development Board
Powerful Software Development Capability for AMD Geode™ NX Processors
The AMD Geode™ NX processor family consists of three versatile and powerful products - the AMD Geode™ NX 1250@6W* processor, the AMD Geode™ NX 1500@6W processor** and the AMD Geode™ NX 1750@14W processor.***
The AMD Geode™ NX processor family leverages advanced architecture to provide powerful solutions for a variety of Internet edge, peripheral applications, and more. The AMD Geode™ NX processor family provides the highest x86 performance for fanless operations.
The NX processor family leverages Mobile AMD Athlon™ processor technology to deliver superior computing power for a variety of thin-client and other applications including point-of-sale terminals, kiosks, high-end printers and home media systems.
Key features include:
* Low-power consumption
* Advanced 7th generation core
* Long-term manufacturing and support
* 128KB level 1 cache
The AMD Geode™ NX processor family is supported by existing low-cost infrastructure, proven architecture and a long-term supply commitment.
The Geode NX 1250@6W processor is based on an AMD Athlon™ core and demonstrates the company’s commitment to making enhancements to its x86 product offerings and delivering a full line of x86 products to market. The AMD Geode family of embedded solutions is part of AMD’s strategy to offer assets, resources and vision for extending x86 solutions from low-power embedded solutions up through the highest-performing server platforms. The Geode NX 1250@6W processor is a cost-effective solution for customers requiring sub-one gigahertz performance without a fan. Operating without a fan not only reduces design costs and allows for better power management, but also allows the processor to co-exist in virtually any environment because it can operate silently.
The AMD Geode NX 1250@6W processor broadens the selection AMD’s customers have for x86 solutions that range from sub-one watt to 14 watts, allowing them to choose a processor that best meets their individual design needs.
.13um fabrication process
128/256KB L1/L2 cache
266MHz Front-Side Bus
Floating Point logic
AMD PowerNow!™ technology
Less than 6 watt maybe i should replace my PSU with battery (typical) to 9 watt (maximum) Total System Power Dissipation
Socket A compatibility
3DNow!™, MMX™ and SSE Instruction Set

New system does not boot properly

I just set up a new system with:
a MS-6728 Neo2 FIS2R Mobo,
1gb Geil PC-3500 RAM (2x512),
2.6C proc.
2 Maxtor 120gb IDE drives RAID 0 with the onboard promise controller.
Lite-On DVD burner
ATI radeon 9800 video card
Enermax 300 watt power supply with:
3.3v - 28amp
5v - 30amp
12v 22amp
170watt total 3.3/5 combined
My problem is that my system NEVER boots up normally. It always freezes in the bios startup. The D-bracket stops at almost every possible combination of led's, which according to the manual the problems were: Testing RTC, Initialize Video interface, Testing memory, Initializing floppy controller, Memory detection, Decompressing bios to ram, possibly more. Sometimes I also just get beeping, either a continuous beep or 8 beeps. A few times it would display the bios startup screen, but halfway down would be gibberish characters and would be locked up. When I then turn the computer off then on again, the bios is reset at least somewhat(i know because I usually disable the full screen image on startup) and says memory timings are too tight, and I have the choice to enter bios or hit any key to automatically fix things. If I hit any key it will boot up ok. However when I restart/turn off the computer, the next time it again does not boot. I tried upping the ram voltages from 2.5-2.9v, and that seems to stay that way in the bios, even when it resets itself. Everything else is set to auto/slow. If I try to manually adjust the memory timings, even to the slowest possible settings, it does not boot, and I must turn it on/off a few times till the bios resets again, with the boot process stopping at one of the possiblilitys mentioned above. Using the info tab on speedfan, I got the memory info, and it displayed the voltage at 2.5v, not sure what that means but it is strange.
What I have already attempted:
I sent back the ram and got a new set, which hasn't changed anything. The first time the other ram failed memtest, this time it passed(for about 2 hrs). So I don't think its the ram.
I borrowed an antec truepower 430w powersupply, which had no effect.
I went back to bios version 1.3 from 1.9, which also seems to have no effect.
I was hoping to overclock the system a bit and enable performance mode etc etc, but now I'll be happy to just not have to go through a song and dance everytime I restart the computer. This is only the second computer I have built from scratch, and the first with raid, but that seemed to all go ok. Please help me diagnose the problem!

I too am having problems with my system.
865PE Neo2-FIS2R
2 Maxtor 120GB S-ATA drives, RAID 0, Promise
2 512MB Geil Ultra CL2-3-3-6
HP CD-RW
What IDE settings are you using?
E.g...Native? P-ATA Only...all of those settings
For me...sometimes XP will install and boot...but eventually system is unstable and XP crashes and corrupts itself...Event Manager errors different each time
Someone mentioned problems with Maxtor and AMI BIOS...anything I should keep in mind?
Sorry about all the different questions. I'm sure exactly where my problem lies. MSI thinks it may be my memory AND/OR on-board IDE controller since I can't get the on-board Intel RAID setup to consistently "see" and setup my RAID drives...even when it has worked...XP doesn't like the Intel configured RAID drives. Also tried just one S-ATA drive through on-board Intel and Promise. Next I will try a plain old IDE Hard Drive...no S-ATA...and make sure my memory passes memtest86+ testing.
Any other gems you can offer for this config??? Thanks.

HT4790 My Mac OS Lion 10.7 FileVaulted HD does not boot, prohibitory sign, stop sign appears some minutes after boot starts. Disk Utility repair shows four error messages: Unable to bootstrap transaction group 2517: inconsistent crosscheck (the same with

My Mac OS Lion 10.7 FileVaulted HD does not boot, prohibitory sign, stop sign appears some minutes after boot starts. Disk Utility repair shows four error messages:
Unable to bootstrap transaction group 2517: inconsistent crosscheck
No valid commit checkpoint found
The volume xxxxxxxxxxxxxx(here it shows physical volume number) was found corrupt and can not be repaired.
Problems were encountered during repair of the partition map
Error: Storage system verify or repair failed.
(the same with 2518, 2519 and 2520 transaction group)
I suppose it is serious bug in Mac OS Lion managing FileVault and wonder what the help could be?

Most likely culprit is your Lacie drives which are notorious for flaky power supplies which cause just the sort of erratic behaviour that you describe. Have had similar issues myself. Lacie has been good about replacing my power converter-- twice. If you have seven of them, good luck finding the bad one or more. Like I said, the behaviour is erratic. Sometimes it'll work sometimes not. I can't comment on Samsung drives because I've never used them and have never heard anything about them. Same with Softraid. Why not just use Disk Utility. Sounds like you're ready for an external hardware raid. This will be much faster, much more reliable, and may even be cheaper than seven firewire drives. Check out G Tech, and Maxx Digital for starters.
Best of luck
Terry

Win XP does not boot

Similar Messages

Maybe you are looking for