Win7 does not see my Mac Drive?

after buying a macbook pro for the first time i installed windows7 using bootcamp. i use autodesk inventor, but it seems i do not get this to work properly with parallels, so i am forced to use bootcamp and reboot all the time and switch between autocad for mac and inventor... now i have one big problem and that is that i need to be able to reach and open the autocad files on my macdrive/partition... but windows 7 does not show me the macdrive/partition. in disk management in windows it shows up, but the only thing i can do there is to delete the partition. also the partiotion does not have a drive letter? but again the only tas i can do to this partition is "delete"
can some one tell me how to get this partition to show up under win7 and to use the files there
thank you

buurjongenshon wrote:
can some one tell me how to get this partition to show up under win7
MacDrive or [_*HFS+ for Windows*_|http://www.paragon-software.com/home/hfs-windows> should take care of that.
JGG

Similar Messages

Equium A60 does not see a recording drive

Sadly more help is needed with my Equium A60 following on from the earlier fault of the missing CD\DVD drive. Thanks for the help earlier, I did get my cd drive back in 'My Computer' and it does read cds..
Today I tried to put some mp3s on a known working CDRW and my DVD writer is not seen. I get a error message saying you don't have a cd writer.. I have CD Creator 6 which I have been using ok before, that too does not see a recording drive on my laptop.
I can no longer format a blank cdr or drag and drop on a cdrw formatted previously.
Any ideas anyone.?? Thanx.!!

Hi,
in 'My Computer' right-click on the DVD drive and select properties. Check if on the record tab CD-recording is activated.
Bye

Bootcamp does not see replacement DVD drive in Mac Pro3,1

Recently purchased LG Super-Multi Drive - Mac Pro Kit 24X 5.25" Internal DVD/CD Writer from OWC and installed it in lower DVD drive according to the manuel provided including wire to Sata plug in Mac Pro3,1. A difference is that Top of 2 DVD ports has a faulty drawer door so I have removed the original Apple DVD device from it.
I now have DVD access/play using LG in Mountain Lion with bottom Drive but none at all in Boot Camped Windows 7 or 8 which do not see the SATA drive in lower drawer.
Wondering if there is any fix for this.

My Latest email back & forth with OWC:
My Mac Pro is 3,1 early 2008. My understanding before purchase was that it would work in Mt. Lion and Windows.
Is there anyone who knows how to make this work?
This is a very well known issue that was discovered shortly after the 2006 Mac Pro first shipped.
Sincerely,
OWC Andy

FCPX does not see my external drive?

Need some help. When I open FCP it identifies my external hard drive for a second or two but then it disappears. I can see it in the finder and on my desktop no problem. Also, when I start a new event it does not see my external videos hard drive. It is a brand new Seagate - I have not used it for time machine back ups and before I upgraded to Lion it worked fine. Now I can't bring in projects that I saved to the external Hard drive. I'm new to this software so I would really appreciate some help as I can't even begin to contemplate doing this project a third time.

Take a look at the name of the drive, as well as to the names of folders at the root of that drive.
FCP is probably treating your drive as a camera. You may know for sure by selecting File->Import from Camera and see if your drive appears there.
Don't call your drive "Video", for instance - and avoid common names used in camera folders, like "DCIM".

Win7 install does not see new hard drive (640gb Samusung) on MacBook Pro

Replaced MBP 5,4 (mid 2009) hdd with a Samsung HM641JI 640gb drive. OS X installation went fine using SL install disk, updated software to 10.6.4. Problem is with Windows 7 installation using Boot Camp. Partition is created (tried 32 to 300 gb). Windows 7 install disk loads but after "Install now" and accepting license agreement, it does not recognize the drive or any partitions. XP install works fine. Had same Win7 problem with 2 identical hdds and 3 different install disks which were full version, not upgrades. Installed Win7 using boot camp on 320 gb Samsung drive (also 3.0gb/s SATA) without a problem. Tried formatting the bootcamp partition on the 640 gb drive to NTFS, but still not recognized. Any suggestions?

Odd you can't see anything. I'd use Windows 7 recovery tools to do a full initialize and map out bad blocks if necessary. Or initialize from OS X drive and then do full slow format etc from Windows DVD.
Every drive vendor has their own linux/dos/windows utility to recertify and test sectors and does a better job than anyone else's. WD Lifeguard for all my WD drives, can be very handy.

G3 does not see desktop hard drive.

Hello! Back in April 2006, I purchased a blue and white G3 from my employer. I installed some extra memory, wiped the hard drive clean and installed OS 10.3.x and Adobe CS. Everything worked beautifully.
I shut down the computer, unplugged it, wrapped it in plastic and stored it in a safe place until I moved to my new home. I recently took my G3 out of storage over the holidays and tried to set it up. When I turned it on, I got the “Happy Mac” symbol along with the blinking “question mark”. I was disappointed that all of the previous installations I had put in seemed to be missing.
I decided to re-initialize the hard disk (desktop) and re-install the OS 10.3.x and the other Adobe programs. The G3 has no problems starting up from the start up disk, but there is no desktop ( or hard drive) icon in the upper right corner of the screen. Only the start up disk icon is visible.
When I start to install the OS 10.3.x, I get stuck where it prompts me to select a volume to install the OS. There are no options. I cannot select my hard drive because it simply does not appear. The “options” button is “grayed” out.
I tried using the disk repair utilities and still I had no success in locating the hard drive.
There were 3 items which were showing up in the list, all of which had a “CD” icon. The first icon had a disk with a Japanese sounding name. I could not select it and I could not even verify or repair it. The second icon was also with a disk, with the name “Session 1”. Again, this could not be verified or repaired. The third icon was the start up disk icon.
It is as if my computer can’t see itself! I can’t install anything because there seems to be no desktop to install it into. It is quite frustrating, especially because I had taken the time to set it up last year and everything was working perfectly fine before my computer went into storage. My G3 seems to be “happy” even though it can’t start up without a start up disk. I am hoping that I don’t have a hard drive melt down. I would greatly appreciate some help on this! Thank you!

Hi Limnos, Grant and Eustace,
Till now, I had my G3 on "sleep" with my start up disk in the CD drive. I followed Limnos' instructions and opened up the side again. I made sure I was grounded and I tapped the hard drive. There was no noise or whirring. I placed my fingers on it, and there were no vibrations. The Blue Moo was really blue now. I thought for sure the drive was dead. With a heavy heart, I began to close the computer up. As I clicked the side closed, all of a sudden, I heard the familiar "whir" of a hard drive. I dared not to get too excited. I quickly ejected the start up disk, and lo... the G3 started up on its own!!!!! I had my hard drive icon, my programs, everything was there!
I had no problems re-installing the OS 10.3.x, I had no problems upgrading my Adobe CS programs.
My hard drive was there, exactly where it was supposed to be.
I don't know what exactly what brought it back from the dead. It may have been a combination of all your good advice put together and a bit of luck. In any case, I am up and running and I am truly thankful to all of you for your help. I also learned quite a bit from this experience from you guys, and that in itself, was very valuable to me!
I can't believe how last week, I was thinking I may need to get rid of my G3. But I stuck to it, and with your help, I now have a fully functioning machine!
Buckets of thanks to you again!
The Blue Moo (a very happy Moo indeed!)

Itunes does not see my cd drive

My iTunes installation used to show my CD drive in the left column when I inserted an audion cd into my drive. Now, suddenly, it does not. I can force iTunes to play the audio file on the cd but when it finishes playing a tune, the next tune up always is selected automatically from my Music Library. Very annoying. How do I get iTunes to see my cd drive and list it in the left column?
Thanx .

Hello coffeethecat28,
I found an article with steps you can take when iTunes is not recognizing an audio CD. I recommend following the steps in this article:
iTunes for Windows doesn't recognize my audio CDs
http://support.apple.com/kb/TS1584
Thank you for using Apple Support Communities.
Best,
Sheila M.

Macbook does not see new hard drive

I have one of the first black macbooks...
Intel Core Duo
2GHZ
2mb L2 Cache
2GB RAM
667 MHz bus
Boot ROM Version: MB11.0061.B03
SMC Version 1.4f12
I had an 80GB HD in it that has died. I decided to replace it with a WD Scorpio Blue 160GB.
I've booted to the optical drive and went into Disk Utility to format the new drive but the computer would not recognize the drive. So I formatted it with another computer using a USB enclosure. I put the new HD back and still not recognized.
I then went ahead and installed Snow Leopard on the new drive via USB enclosure, using the macbook I would eventually put the drive into.
Now when I put the new drive, with the OS installed, still not reco

Let us resume the required steps, after putting inside a new, virgin disk:
1. Start up machine and as soon as possible put CD/DVD, press key C to force boot from CD; if the sequence is not fast enough and machine passed over the initial phase, and ? was displayed, force shut down by pressing button key, then start again, with CD/DVD inside
2. Press key C after start, and wait until the Apple logo in displayed, wait
3. You will see a list of install language, choose one, and
4. Go to Apple bar and choose Disk Utility; on the left side, you will see the disk, select it, then, on the cenral-lower part of displayed windows go to Options and choose Apple Partition Map (APM), go back and choose, if not already chosen by default, Mac OS Extended Journaled (HFS+), 1 partition (or more, some prefer more than one), click to partiion/erase disk. Note that you MUST have both conditions achieved: APM and HFS+
5. Close Disk Utility and revert to installation proper, proceed.
If you do not see the disk on the left side of Disk Utility, then disk is damaged or badly connected.
P.S. The same procedures are applied to any disk, with the note that:
- for Intel Macs, partition map should be GUID, not APM
- for external disks or flash drives intended to smoothly work with Windows, format should be FAT 32 and Master Boot Record; NTFS may be done with an additional utility like NTFS-3G or NTFSmounter

MBA 13" (Mid 2012) 10.8.2 does not see other Macs

Hello all,
for some time now I have a strange problem with my 13" MBA (Mid 2012 - latest version) on 10.8.2. THe MBA generally works very well, fast, and stable. My only issue is that I cannot see or connect to other Macs in my home WLAN network (this worked seamlessly under 10.8.1) or elsewhere. The other Macs do not show up in the finder, and neither can I connect with them manually (via "Go to server...").
The only way to establish a connection is via creating a computer to computer network - which works perfectly but, of course, disconnects me from the internet which comes over wifi, so this is not a permanent solution.
Even stranger, there seems to be a problem with ethernet connections (via thunderbolt ethernet adapter), too. This connection work seamlessly with one of my other Macs (running on Lion - 10.7), but does not work with my iMac running on Mountain Lion 10.8.2.
I guess that something's wrong with the sharing routines on my MBA. Therefore I tried to install the 10.8.2 combo update but had to learn that this was not made for the 2012 MBA... :-(
So, what to do? Should I try a reinstall of Mountain Lion?
Any help would be appreciated.
Thanks,
Jan

Hello medeostrike,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/ht3964
Best of luck,
Mario

AirPort Extreme does not see printer, hard drive, AirPort Express!

I just got an AirPort Extreme (802.11n), to replace my AirPort Express. I have a Brother 665CW wireless all-in-one printer, which had worked perfectly but now I cannot find it. I have also hooked my USB hard drive into the Extreme. I can see the hard drive in the AirPort Utility, but I don't know how to find it from my iBook. I'd also like to put the Express in another room to use the AirTunes feature. Unfortunately, almost nothing is working!
Here is how it's set up:
Den:
AirPort Extreme - hardwired to:
- DSL modem
- hard drive (via USB)
Brother 665CW (wireless)
Living Room:
AirPort Express
Advice would be appreciated. I'm usually able to troubleshoot my problems, but documentation on this Extreme is really bad! Thanks!
iBook G4 Mac OS X (10.4.9)

I had problems adding Airport expresses using Airport Utility. However I found it worked fine if I used the manual set-up option and not the Assist me option.
Reset the airport express then, in manual set-up, set the express to 'join an airport network' add the airport network password and see if that works

My time capsule does not see external hard drive

I just got a new time capsule and am hoping to use it as a wireless bridge and NAS.
I've got it set up as a bridge and that seems to be working correctly, but when I plug my external hard drive into the time capsule, I can't see that external drive show up anywhere.
Has anybody else run into this issue?
The hard drive is a WD Elements 3 TB USB 2.0 Desktop External Hard Drive - WDBAAU0030HBK-NESN.

I can't see that external drive show up anywhere.
If the drive is formatted correctly and communicating with the Time Capsule, then it will be displayed when you open AirPort Utility, click on the Time Capsule icon, click Edit, and then click the Disks tab at the top of the next window. Example:
Remember that since this drive is a "network" drive, it will not be displayed on the desktop until you manually mount the drive.

Frustrated - Installer does not see all hard drives

Ok. I'm a pretty basic user and here is my situation. I have a G5 with two internal drives. On one drive "A" I have OS X 10.3.9 installed (using that now) on the other internal drive (B) I have 10.4.7. All was working fine using drive "B" as my start up until I used Tech Tool this morning to check/repair volumes on "B". After all the repairs made I tried reboot to OS-X 10.4.7. The choice was there in System Preferences.
No luck, I now only get the black death screen telling me to reboot. Rebooting does nothing except bringing the must shut down and reboot screen. I tried to use my 10.4 Tiger installation disk to reinstall 10.4 on the "B" drive but the Apple installation program doesn't "see" the drive and so doesn't offer it as an option to install to. The program only sees the "A" drive.
I tired to install 10.4 on my "A" drive as an upgrade- I get an "errors" almost immediately after it starts and cannot install the up-grade.
I tried disk utility (from A drive trying to repair B drive)- it cannot "repair" disc B. I can see and use my B harddrive when in 10.3.9 - all programs and files are there and useable - but I can't boot from it nor is it recognized by the Tiger Installation disc. I seem stuck in 10.3.9.
I have a brand new external firewire drive not hooked up - I'm tempted to drag all files from "A" and copy it to the new drive and then reformat the "A" drive and try a clean install on "A" with 10.4. But I'm a bit nervous - if it doesn't work then I'll have no functioning operating system.
Sorry. I'm going a little crazy. Any ideas? I'm frustrated and plan to trash Tech Tool if I ever get back to 10.4.7.
G5 Mac OS X (10.4.6)

It looks like both your drives have serious problem (that's why Disk Utility says it can't repair and you can't update the system in drive "A"). The fact that you can boot into 10.3.9 doesn't mean that the problems don't exist. In your case I would trust either drive and would do a backup of all the data, reformat the drives and then reinstall everything since the tols you have can't solve the problems.

Aperture import does not see/recognize external drive

I've searched quite a bit for an answer to this and have come up empty, so I apologize in advance if I simply missed it.
I am having issues with Aperture not showing a couple external drives in the Import view. It recognizes my iphones, ipad, SD cards, but not these three external SATA drives, which are formatted NTFS. The OS sees them as they appear in Finder and I can browse them just fine.
Any ideas?

I've been using this application without incident for
several weeks now; coming over or rather
transitioning from WIN7 and Lightroom to
MAC OS and Aperture; Aperture is the best DAM
I've seen but a little light as a raw image file processor
IMHO (so far..that is..I have a whole two weeks of
working with A3 and nearly 5 years with LR)
Anyway's I'm referencing files on the TC and importing
into the Aperture library..there is simply no sign of the import
browser at the bottom of the import screen.. I wonder if the
10.7.1 LION update broke something as I did do that update a
few nites ago and have not tried any imports for a few days..
just noticed this today as the other poster evidently did..
I'm going to try a simple import from a USB thumb drive to see if that works..

Adobe PS CS4 does not "see" my USB Drives in Finder

For some bizarre reason, PS CS4 is no longer "finding" my USB 2TB drive in the Finder/Devices window on my iMac (nothing is showing in devices). However, it is seeing my my WD NAS drives, and if I go into Finder on my own, it shows the USB drives. The WD drives are a 2TB MyBook, and a 3TB MyCloud. I have had some issues with _those_ drives showing up in Finder but its usually a WD firmware issue... and its usually the older MyBook drive that gives me problems. Anyway... the aforementioned 2TB USB drive also appears (as it should) on the RHS of my iMac screen. The drive is working just fine, and I have tried powering off the computer and the USB drive... still doesn't show using Photoshop. I can search within finder for the file I want, and right-click to open in "Adobe Photoshop" but I'm so used to grabbing, editing, and saving files from within CS4 that I'm baffled that this drive all of a sudden can't be "seen" from within PS CS4. Previously it had been, so I have to assume its some settings or preferences issue?

As noted above, I am now able to "see" the missing USB drive(s) in Finder so that seems to be resolved. However, a few new issues have cropped up:
1. Not all my installed fonts are in my font listing, but I'll assume I can easily remedy that by activating them (I hope). I have the sneaking suspicion I deleted some by mistake.
2. Safari seems to have gone weird... the upper section is flashing like crazy when I try to type in a URL, also the sidebars flash when I scroll up or down with mouse. I've installed Chrome so I have a stable browser for the time being.
3. No matter what I seem to do in preferences, every new image I open does so within the same window so I have to manually drag it out to compare images. How do I fix that permanently?
4. When I first opened PS this morning I kept getting some sort of error popup that couldn't complete the request?
Is it safe now to remove the new user account?
Mike

Clean install Windows 7 does not see my hard drive

I just bought a new h8-1234 and I want to get everything off of the hard drive. Sorry, I just like to have what I want on my hard drive, not a buch of junk that I will never use.
So, I pop in my trusty Windows & 64 bit disk, the install proceeds and stops...It's tell me to install the drivers for my hard drive and I can see that the hard drive list is empty..
I tried to find the drivers for my modle of computer, but HD drivers are not listed. Is there a generic sata driver I could try on use?

Hi:
You can try the ones I have attached, but I always thought that Windows 7 and Vista had all of the SATA drivers already installed. I've never come across a situation where W7 or Vista asked for Hard drive drivers.
They are the latest ones obtainable from AMD's site.
I see that your PC has a a new AMD 9xx chipset, and that isn't even listed on AMD's site for support.
Paul
Attachments:
AMDx64.zip ‏160 KB

Win7 does not see my Mac Drive?

Similar Messages

Maybe you are looking for