Windows 10 can't shutdown with fast startup mode

I can't shutdown my laptop with fast startup is turn on.All my hardware are off, but the light in power button still on.I have to press and hold the power button to make it off. Then I turn off the fast stratup function and my laptop can shutdown completly.But my laptop can't enter the sleep mode.When i close the lid, it turn off all the my hardwares but the light power won't blink like usual.When i open the lid, the light in power button still on, but i doesn't do anything when i press it. I have to press and hold it again to make it off. I don't have this problem in my previous windows 8.1My Windows 10 is a fresh install. What should i do? Thx

I have installed all updates from Windows Update and all drivers from Toshiba US website. I can't find the Service Station for Windows 10 from Toshiba website. I only found the one for Windows 8.

Similar Messages

Which versions of Window can perform best with CiscoWorks?

Hi,
Please advice that currently we have 3200 logical devices configured on CiscoWorks and CiscoWorks is running very very slow. CiscoWorks installed on server with Windows Server 2003 32-bit and this version of windows it can only support RAM up to 4GB, which is already installed. In order to increase the RAM we have to upgrade the windows version as well.
Please advise that which versions of Window can perform best with CiscoWorks. E.g. Windows Server 2003 with Service Pack 1 (SP1), Standard Edition 64-bit: or Windows server 2008 etc. Please advise us the full windows release version as we will upgrade windows as per your suggestion.
We are currently using the LMS 3.2, RME 4.3.0, CM 5.2.1

Please refer to the Installation Guide for Windows server requirements. Here is the link:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/install/guide1/prereq.html#wp1099303
Given that you want to stay with Windows Server, Server 2008 Standard Edition with service Pack 2 would be your best choice.
NOTE that your should not (and cannot) use Server 2008 R2. That version in only supported with LMS 4.0.1. LMS 3.2 will not work with Server 2008 R2.
With a 64-bit OS, you can increase your RAM - which is usually constraining system performance on systems with 32-bit OS. I recommend just putting in 16 MB. Why skimp on $100 RAM with $20,000 software?
Your other alternative is to divide the server roles across several machines. That is a pretty complex task so I'd do the OS and RAM upgrade first and see how that helps you out.
Re "Linux" LMS 3.2 (and 4.0/4.0.1) is only supported on Windows and Solaris operating systems. Plus if you're not a Uniux admin, the learning curve can be steep for your first dip in the water.

Can't interact with any open windows, can't interact with flash content

I've already tried reinstalling, resetting and deleting my profile, nothing's changed.
I can't close any Firefox window by pressing "x", or by pressing Alt+F4, I can only close it through the task manager or task bar. Minimising or going into windowed mode is also impossible.
If a new window opens itself (e.g. A download) I can't interact with it at all - It's visible on top of the main window, but nothing I do affects it.
I also can't interact with flash content (like pausing a youtube video)
There is absolutely no feedback when I try. The icon doesn't change.
I recently reset firefox, there are no add-ons, themes etc. installed, the problem persists.
I am running Windows 7 64bit, everything else (including other browsers) appears to be working fine and a virus scan (Avast! free version) turned up nothing.
I'd really appreciate any help!

Hello,
'''Try Firefox Safe Mode''' to see if the problem goes away. Safe Mode is a troubleshooting mode, which disables most add-ons.
''(If you're not using it, switch to the Default theme.)''
* You can open Firefox 4.0+ in Safe Mode by holding the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* Or open the Help menu and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
''Once you get the pop-up, just select "'Start in Safe Mode"''
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshooting extensions and themes]] article for that.
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.''
Thank you.

How many users can login simultanisly in Fast user mode?

at one time, i saw in one of the threads that only 3 users can log on to the Mac using Fast user switching. i tried that, and sure enough, i couldn't log in more than 3 users at one time.
today, i tried logging in with 10 users, and i had no problem.
was that ever an issue with fast user switching, or was it only my computer?
Mac OS X (10.4.9)

I have seen mailstores with up to 750,000 actual users. I have seen Directories with 2 million entries, of which less than half were active mail users. You're not running into a product limitation. . .

Shared Disk - can't connect with Fast User Switching

Hi,
I've created a Disk on my Time Capsule, and shared it via "File Sharing", it's secured "with a disk password", and is working well ... sort of. I can connect to it with no issues, and so can my wife via her MacBook Pro. However, if I'm signed into my account, and she accesses her account using Fast User Switching, she can't connect to the shared volume. She has to Disconnect, and then reauthenticate, and after doing so, I can't connect to the shared volume. I must Disconnect, and reconnect. Why is this? Is there an authentication file that's set up some where on the root of the shared computer, that's preventing us from being able to signin to the shared volume? Or is something broken?
Thanks!

Complete uninstallation and reinstallation of network adapter drivers has been reported to resolve this error in some cases. Open
Device Manager and select Show Hidden Devices from the
View menu. Expand the Network Adapters category and delete all drivers under this category. After the devices are removed right click and select
Scan for hardware changes.
Brandon
Windows Outreach Team- IT Pro
Windows for IT Pros on TechNet

Can clips made with different recording modes (SP/LP) be put in same movie?

My cousin recorded the family reunion in LP mode while I had my digital camcorder set to SP. I'm using Premiere Elements 4 to make a DVD using everybody's stills and the two digital camcorders' movie clips. Does it matter about the different recording modes? Can I put clips of both speeds in the same authored movie? If not, I guess I could make two movies and burn both files to the same DVD disk. Can they have the same menu? Or how do I make it easy for viewers to play both movies on their TV (not on a computer)? Thanks for your help and for any suggestions.

If you're talking about a miniDV camcorder that's recorded in both LP and SP -- it won't make any difference at all. Digital data is digital data, as far as Premiere Elements is concerned.

Startup Mode for XI Adapters JDBC and JMS

We have configured several JMS and JDBC channels which are running fine. During application of support packages, we want to disable these channels. I know that I can individually inactive each channel but I am looking for a way to disable all JMS and JDBC channels together.
I am thinking that I should be able to disable the SAP XI Adapter: JMS service and the SAP XI Adapter: JDBC Adapter. The startup modes for these services are set to automatic so when the web as java is stopped and restarted these services will restart.
Am I correct in thinking that I can stop these services without effecting the XI system (i.e. these services are not mandatory)? How can I temporarily change the startup mode for these services to manual?

Hi,
I believe you can stop JMS and JDBC services individually from visual admin but I am not sure (lets give a try).
If you don't mind getting errors i.e, if your motive is just to stop the execution of all JDBC and JMS scenarios, just redeploy the jmsproviderlib sda without any external jars in it.
Regards,
Felix

Windows XP see blank screen when remote desktop to Windows 7 with fast user switching disabled

All computers are in workgroup environment, no AD.
Windows 7 pro are configured with fast user switching mode disabled so that only one login session can run at a time. When a Windows 7 machine remote desktop to another Windows 7 machine, the remote desktop 'server' will give 30 seconds count-down for the
console logged in user to accept remote connection, or when timeout expires it kicks out the console logged in user. This is completely ok.
This become a problem when a Windows XP rd client try to remote desktop to these Windows 7 machines, Windows XP see a blank screen if the remote Windows 7 machine has a user logged in, as it is waiting for the user to log off first. This is not desirable
as our administrators want the console session to be logged out automatically if they (administrators) want to remote desktop in.
Is this a configuration problem? Is this a OS design, can't be changed?
Valuable skills are not learned, learned skills aren't valuable.

Hi,
As I know, for RDP session in Windows 7, you don't need to configure the fast user switch option disabled. Windows 7 doesn’t support multiple Remote Desktop sessions by design, that means only one RDP session at a time.
I remote into my Windows 7 machine (which has a user logged in) from my XP machine, all work fine, the user logged in Windows 7 machine is automatically "kicked off".
May I ask a question? Does this issue happen in all XP machines? If you leave Windows 7 machine started and no user logged in, the RDP session in Windows XP established quickly?
I would suggest you keep latest drivers graphic card and latest updates paches for both Windows XP (Windows XP has come to its end of the lifecycle)and Windows 7.
Yolanda Zhu
TechNet Community Support

Windows 8/8.1 Hybrid Boot (Fast Startup) Problem

Hello, about one week ago I was using my laptop directly on power (without my battery), to preserve my battery a bit. I had an unexpected power cut and my machine went off. When I turned it on again, it seemed as if I was stuck in a boot loop. I
would come up saying it's installing an update, reaches 100% then reverts and restarts. It did this about two times. Now it had installed an update before, the very first time I turned it on that day before the power cut happened.
I managed to access the advanced options, tried startup repair. It had told me it failed. I tried booting again and I got through this time around. When I logged in, I ran sfc/scannow, Dism /Online /Cleanup-Image /RestoreHealth and I also ran
Check Disk to ensure that no damages had been done to my laptop.
Everything seems fine but I noticed one thing was different. I had dual booted my laptop with Windows 7 using a VHD from before. When I am on the Windows 8.1 Pro side, if I just shutdown then power on again. It would take me straight to my Windows
8.1 side. When I logged in, I would notice that in the CPU up time section, in the Performace Tab in task manager, my CPU Time wouldn't be starting from 0:00:00:00, it would have been a continuation from how long the system was on before.
I read up on Hybrid Boot so I know it stores the session to disk so that is to be expected.
But ever since that incident, whenever I boot up. It takes me to the os selection screen prompting me to select an OS. When I log in on Windows 8.1 and I check the CPU time, it has start from 0:00:00:00, so it would say it's been on for
just over a minute or so.
Now this has lead me to believe that something is wrong. My machine still boots up very fast. I also checked my power options, and fast startup is enabled. I checked the registry and HyberBootEnabled is set to 1, which means hybrid boot is
on. I also turned off hibernation so that it would delete my hibernation file and re-enabled it, so that it would rebuild my hibernation file.
Nothing appears to be wrong with my system, everything else functions the way it used to but it's that one issue which I've noticed that has me slightly concerned that some setting may have been disabled or some file has been corrupted, as why to
it doesn't boot the way it used to.
My guess, is that it is not resuming the session stored. That's just my guess.
I have then since removed my dual boot configuration and reloaded my BCD which I had exported before I dual booted. So now I'm back to original boot configuration. I no longer get sent to os selection screen, as there is only one os now. But
the issue with CPU up time always starting from 0:00:00:00 is still present.
If anyone knows what's the real issue at hand or anything at all that may help, I'm kindly asking for your help.
My Machine Specs:
Operating System: Windows 8.1 Pro 64-bit (6.3, Build 9600) (9600.winblue_gdr.131030-1505)
Language: English (Regional Setting: English)
System Manufacturer: LENOVO
System Model: 20193
BIOS: 6BCN43WW(V2.03)
Processor: Intel(R) Core(TM) i7-3630QM CPU @ 2.40GHz (8 CPUs), ~2.4GHz
Memory: 16384MB RAM
Available OS Memory: 16332MB RAM
Page File: 4535MB used, 17421MB available

CPU Time wouldn't be starting from 0:00:00:00, it would have been a continuation from how long the system was on before. I read up on Hybrid Boot so I know it stores the session to
disk so that is to be expected.
CPU time, it has start from 0:00:00:00, so it would say it's been on for just over a minute or so.
fast startup is enabled. I also turned off hibernation so that it would delete my hibernation file and re-enabled it, so that it would rebuild my hibernation file.
But the issue with CPU up time always starting from 0:00:00:00 is still present.
Seems you done almost all to solve this yourself. So I'm only doing a checklist to see if you completed these things.
Type in the search disk, choose,
free up disk space, unselect all, except temporary
files
Type in search Po bu, click, what the power buttons do, select,
change settings that are currently unavailable, uncheck turn on fast boot, Check, Hibernate to show in powermenu, then goto power menu, setup your hibernate settings. Shutdown computer, poweroff, upplug cord
and battery, wait for a minute then bootup.
Go into your bios and make sure your booting from UEFI, if your using UEFI, (if not then the functions and benefits of fastboot will not
work) and fastboot is enabled in the bios. If all is correct boot to your system.
Type in po bu again and enable turn on fast boot. Turn off the system again and power it off. Startup, lets see if all is working now

My mac is running slow, the spinning beach ball constantly appears. it seems that when i am in the apple store with fast wifi its a bit better. genius at the apple store checked the hard drive, it's all fine. what can it be?

my mac is running slow, the spinning beach ball constantly appears. it seems that when i am in the apple store with fast wifi its a bit better. genius at the apple store checked the hard drive, it's all fine. what can it be? can it be a software issue with the wifi?
also i noted that it has only been doing this since quite recently, before it was fine
please help!

First, back up all data immediately, as your boot drive might be failing.
Step 1
This diagnostic procedure will query the log for messages that may indicate a system issue. It changes nothing, and therefore will not, in itself, solve your problem.
If you have more than one user account, these instructions must be carried out as an administrator.
Triple-click anywhere in the line below on this page to select it:
syslog -k Sender kernel -k Message CReq 'GPU |hfs: Ru|I/O e|find tok|n Cause: -|NVDA\(|timed? ?o' | tail | open -ef
Copy the selected text to the Clipboard by pressing the key combination command-C.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). I've tested these instructions only with the Safari web browser. If you use another browser, you may have to press the return key.
The command may take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear.
A TextEdit window will open with the output of the command. Normally the command will produce no output, and the window will be empty. If the TextEdit window (not the Terminal window) has anything in it, stop here and post it — the text, please, not a screenshot. The title of the TextEdit window doesn't matter, and you don't need to post that.
Step 2
There are a few other possible causes of generalized slow performance that you can rule out easily.
Disconnect all non-essential wired peripherals and remove aftermarket expansion cards, if any.
Reset the System Management Controller.
Run Software Update. If there's a firmware update, install it.
If you're booting from an aftermarket SSD, see whether there's a firmware update for it.
If you have a portable computer, check the cycle count of the battery. It may be due for replacement.
If you have many image or video files on the Desktop with preview icons, move them to another folder.
If applicable, uncheck all boxes in the iCloud preference pane. See whether there's any change.
Check your keychains in Keychain Access for excessively duplicated items.
Boot into Recovery mode, launch Disk Utility, and run Repair Disk.
If you have a MacBook Pro with dual graphics, disable automatic graphics switching in the Energy Saverpreference pane for better performance at the cost of shorter battery life.
Step 3
When you notice the problem, launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Activity Monitor in the icon grid.
Select the CPU tab of the Activity Monitor window.
Select All Processes from the View menu or the menu in the toolbar, if not already selected.
Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for User, System, and Idle at the bottom of the window.
Select the Memory tab. What value is shown in the bottom part of the window for Swap used?
Next, select the Disk tab. Post the approximate values shown for Reads in/sec and Writes out/sec (not Reads in andWrites out.)
Step 4
If you have more than one user account, you must be logged in as an administrator to carry out this step.
Launch the Console application in the same way you launched Activity Monitor. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Select the 50 or so most recent entries in the log. Copy them to the Clipboard by pressing the key combinationcommand-C. Paste into a reply to this message (command-V). You're looking for entries at the end of the log, not at the beginning.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some personal information, such as your name, may appear in the log. Anonymize before posting. That should be easy to do if your extract is not too long.

TS1368 HELP!!! After upgrading to IOS 6.13 my IPAD Stucks in a plug-in screen and the Itunes. When i Try to connect to iTUNES pop-up message apear "iTunes has detected an iPad in recovery mode.. You must restore this iPad before it can be used with iTunes

I have windows 8 enterprise OS and iTunes ver. 10.5.0.142. I was upgrading my iPad to IOS 6.1.3. After finishing the upgrade my iPad Reboot and currently stucked-up in a plug-in screen and iTunes Logo. When I try to connect it to the iTunes pop-up message appear saying " iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes." In short, I push the restore button then another pop-up message appear saying " The iPad software update server could not be contacted. Make sure your network settings are correct and your network connection is active, or try again later." I tried many ways but still no luck. I repeatedly reboot the iPad and open the iTunes still the same problem. I try also to uninstall the iTunes and installed the lower version but still the same problem, I even check the firewall if the ITunes was block or My privileges is administrator to run the iTunes or even reset my winsock but the problem still remain. PLEASE HELP! Thank you in advance!!!

Turn off your firewall and antivirus software.

I recently bought an Ipod touch 2nd gen, (Ebay). It's in great shape and seemed to be wiped clean. When I connect (via windows computer) to Itunes with usb cord the Ipod icon shows, but the only function you can do is eject. When its in the upper right h

I recently bought an Ipod touch 2nd gen, (Ebay). It's in great shape and seemed to be wiped clean.
When I connect (via windows computer) to Itunes with usb cord the Ipod icon shows, but the only function you can do is eject. When its in the upper right hand corner and you click on it all you get is a done button, when it's in the side bar right click and your only option is eject, left click has no effect. If I go to "file">devices it's as if there are no devices connected.
I purchased a song with Itunes on the Ipod itself, and it transferred to my library on the computer automatically .
I have an Iphone 5 and a nano that are still functioning with Itunes thru computer so I'm thinking the issue is with the Ipod touch. I've reset it several times, rebooted it, with no change.
nothing on the internet has helped, I called tech support and got disconnected. Should I take it to a retail store? I just don't know where to go next, I'm of course willing to pay for tech or repair. looking for suggestions.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

[SOLVED] Can not shutdown/restart from KDE with systemd

Hello,
Recently, following I switched to a pure systemd setup. The process was simple and most things worked "right out of the bpx". However, I can not shutdown or restart from KDE!
Let's say that I do the 3 finger salute (ALT-CTRL-DEL) and select "Turn off computer" what I get is KDE shutting down, but then I will only get a console (TTY) login prompt. Pressing ALT-CTRL-DEL then will trigger a reboot. I can also login and use "systemctl poweroff". However, I don't understand why it doesn't work straight from KDE.
Are there some packages I must install? Are there some systemd services that I must enable? What other relevant info should I include in this post?
Active units :
UNIT LOAD ACTIVE SUB JOB DESCRIPTION
proc-sys...misc.automount loaded active waiting Arbitrary Executable File Formats File System Automount Point
sys-devi...d-card0.device loaded active plugged MCP79 High Definition Audio
sys-devi...da-sda1.device loaded active plugged ST9500420ASG
sys-devi...da-sda2.device loaded active plugged ST9500420ASG
sys-devi...da-sda3.device loaded active plugged ST9500420ASG
sys-devi...da-sda4.device loaded active plugged ST9500420ASG
sys-devi...da-sda5.device loaded active plugged ST9500420ASG
sys-devi...da-sda6.device loaded active plugged ST9500420ASG
sys-devi...ock-sda.device loaded active plugged ST9500420ASG
sys-devi...et-eth0.device loaded active plugged RTL8111/8168B PCI Express Gigabit Ethernet controller
sys-devi...t-wlan0.device loaded active plugged AR928X Wireless Network Adapter (PCI-Express)
sys-devi...y-ttyS0.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS0
sys-devi...y-ttyS1.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS1
sys-devi...y-ttyS2.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS2
sys-devi...y-ttyS3.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS3
sys-module-fuse.device loaded active plugged /sys/module/fuse
-.mount loaded active mounted /
dev-hugepages.mount loaded active mounted Huge Pages File System
dev-mqueue.mount loaded active mounted POSIX Message Queue File System
home.mount loaded active mounted /home
run-user-1000-gvfs.mount loaded active mounted /run/user/1000/gvfs
sys-fs-f...nections.mount loaded active mounted FUSE Control File System
sys-kernel-debug.mount loaded active mounted Debug File System
tmp.mount loaded active mounted /tmp
cups.path loaded active waiting CUPS Printer Service Spool
systemd-...d-console.path loaded active waiting Dispatch Password Requests to Console Directory Watch
systemd-...word-wall.path loaded active waiting Forward Password Requests to Wall Directory Watch
bluetooth.service loaded active running Bluetooth service
colord-sane.service loaded active running Daemon for monitoring attached scanners and registering them with colord
colord.service loaded active running Manage, Install and Generate Color Profiles
console-...daemon.service loaded active running Console Manager
console-...-start.service loaded active exited Console System Startup Logging
cups.service loaded active running CUPS Printing Service
dbus.service loaded active running D-Bus System Message Bus
[email protected] loaded active running Getty on tty1
kdm.service loaded active running K Display Manager
NetworkManager.service loaded active running Network Manager
sshd.service loaded active running OpenSSH Daemon
systemd-journald.service loaded active running Journal Service
systemd-logind.service loaded active running Login Service
systemd-...s-load.service loaded active exited Load Kernel Modules
systemd-...unt-fs.service loaded active exited Remount Root and Kernel File Systems
systemd-sysctl.service loaded active exited Apply Kernel Variables
systemd-...-setup.service loaded active exited Recreate Volatile Files and Directories
systemd-...rigger.service loaded active exited udev Coldplug all Devices
systemd-udevd.service loaded active running udev Kernel Device Manager
systemd-...ssions.service loaded active exited Permit User Sessions
systemd-...-setup.service loaded active exited Setup Virtual Console
udisks2.service loaded active running Storage Daemon
upower.service loaded active running Daemon for power management
wpa_supplicant.service loaded active running WPA supplicant
cups.socket loaded active running CUPS Printing Service Sockets
dbus.socket loaded active running D-Bus System Message Bus Socket
systemd-initctl.socket loaded active listening /dev/initctl Compatibility Named Pipe
systemd-journald.socket loaded active running Journal Socket
systemd-shutdownd.socket loaded active listening Delayed Shutdown Socket
systemd-...control.socket loaded active listening udev Control Socket
systemd-...-kernel.socket loaded active running udev Kernel Socket
basic.target loaded active active Basic System
cryptsetup.target loaded active active Encrypted Volumes
getty.target loaded active active Login Prompts
graphical.target loaded active active Graphical Interface
local-fs-pre.target loaded active active Local File Systems (Pre)
local-fs.target loaded active active Local File Systems
multi-user.target loaded active active Multi-User
network.target loaded active active Network
remote-fs.target loaded active active Remote File Systems
sockets.target loaded active active Sockets
sound.target loaded active active Sound Card
swap.target loaded active active Swap
sysinit.target loaded active active System Initialization
systemd-...es-clean.timer loaded active waiting Daily Cleanup of Temporary Directories
LOAD = Reflects whether the unit definition was properly loaded.
ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
SUB = The low-level unit activation state, values depend on unit type.
JOB = Pending job for the unit.
72 units listed. Pass --all to see inactive units, too.
Last edited by Prozzaks (2012-08-20 17:35:48)

Demon wrote:For me the system only halts, it does not poweroff. How I can solve this?
As bgc1954 said, there is also a symlink "/sbin/poweroff". Just edit the file "/usr/share/config/kdm/kdmrc", go to [shutdown] an replace the line "HaltCmd=/sbin/halt" with "HaltCmd=/sbin/poweroff".

My macbook pro will not boot. It gets the grey screen with the apple until the bar is half way across and then shuts down. The only screen I can get to is in safe mode and I don't know what to do with that

my macbook pro will not boot. It gets the grey screen with the apple until the bar is half way across and then shuts down. The only screen I can get to is in safe mode and I don't know what to do with that

Mac OS X: Gray screen appears during startup - Apple Support

Windows can't find Apple Mobile Device (Recovery Mode) after iTunes 9.2 upg

Hey guys!
My iPhone 3G (3.1.3) and iTunes (9.1) has been working normally when I upgraded iTunes to the 9.2.0.61 version to install the OS4 in my iPhone.
After this, when my iPhone turn on in Recovery Mode, Windows cannot find the driver "Apple Mobile Device (Recovery Mode)" and the iTunes can't upgrade to OS4.
If I turn on my iphone in normal mode, Windows can install successfully the driver and iTunes recognize the iPhone.
I put my iPhone in another PC (with Windows XP and iTunes 9.1) and the Windows found and installed the iPhone drivers in Recovery Mode. But, in this computer, I've also tried upgrade the iTunes to 9.2 version and the same Problem has benn ocurred.
Someone else has the same problem???
Thanks for help!

I GOT THE SOLUTION!!
This problem happens due a conflict between the Samsung's Software "NEW PC STUDIO" and the Apple Drivers!
The solution is unistall all Samsung's Software and removing all Apple Softwares as well (like iTunes, device drivers etc)
Then cleaning the Windows Register with some software like CCleaner AND manually using REGEDIT, just find for Samsung (carefully with other Samsung Devices like HardDrive. You musn't remove something like that) then, finding for New PC Studio.
Remove all Keys related Samsung New PC Studio.
Restart your PC and reinstall iTunes lastest version.
Now, you can put your iPhone in Recovery Mode that Windows will recognize it!

Windows 10 can't shutdown with fast startup mode

Similar Messages

Maybe you are looking for