Windows 10 in Boot Camp Thunderbolt Display

I installed the technical preview on a 27" late 2013 iMac using the most recent Boot Camp Assistant. While some listed fixes for WiFi adapter worked, I have a second display connected by DVI > Thunderbolt. I have tried disabling fast startup, a confirmed
fix for Thunderbolt input not being detected. I have also tried running AMD support installer for drivers on Windows 8.1 for Boot Camp for my iMac model, and the driver install fails. I realize it's a bit of a niche issue, but if anyone has any ideas I'd love
to hear them.

Hi,
According to your description, it seems a Thunderbolt driver issue or a device compatibility issue with Windows 10 Technical Preview, while we have little experience with Thunderbolt Display
So, in order to better help you, I would recommend post this issue in
Apple Support Communities
NOTE
This
response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you.
Microsoft
does not control these sites and has not tested any software or information found on these sites.
Yolanda Zhu
TechNet Community Support

Similar Messages

Apples update didn't work for me: Boot Camp: iMac displays a black screen during installation of Windows 7

Boot Camp: iMac displays a black screen during installation of Windows 7 - Apple Support
I have followed each of the steps listed in the link above with no success.
Prior to adding the extra drivers I was able to start the Windows install process up to reformatting the "Windows" Bootcamp drive. After that the computer would go through some instal processes and eventually restart. After the restart the screen would go black. The black screen lead me to the Apple Support link above dated March 5 2015. After going through steps listed in the link above, I get an error message stating that the D:\Sources\instal.win. file cannot be located. I am forced to restart the computer at that point and theWindows install process attempts to start again but always ends up at the same point.
Note: I am installing windows 7 Pro from a DVD. I scanned the AutoUnattend.xml file and noticed that it refers to "Windows 7 ULTIMATE" but not "Pro" or any others that I could see. (see below). Could that be part of the issue?
Any feedback would be greatly appreciated.
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
</unattend>
iMac (27-inch, Late 2009)
2.66 GHz Intel Core i5
16 GB 1067 MHz DDR3
ATI Radeon HD 4850 512 MB

Here is an over-simplified explanation of WIM and CLG files. Assume your DVD Media contains
W7- Ultimate
W7- Professional
W7- Home Premium
W7- Home Basic
WIM Files
File1
y
y
y
y
File2
y
y
y
y
File3
y
File4
y
y
File4
y
y
y
The File .wim will contains a compressed image which contains File [1...5].
The W7-Ultimate .clg will have 5 entries, with all set to 'Y'.
The W7-Professional .clg will have 5 entries, with 'Y','Y','N','Y','Y'.
The W7-Home Premium .clg will have 5 entries, with 'Y','Y','N','N','Y'.
The W7-Home Basic .clg file will have 5 entries, with 'Y','Y','N','N','N'.
This allows a single .wim Image file on the DVD media to be used to install any of the 5 flavors of Windows. When you enter your product key, the Installer knows what specific W7 variant you have the key for and will tell the WIM to extract the specific files the installer needs to be extracted.
The following line
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
is telling that a retail product key will be entered, which should go look for this specific .clg file (from the five you already have on disk). You can test if it will work for you by changing this line to the following
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 PROFESSIONAL" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
If it does not work, the other issue can be related to device discovery. Typically A: and B: device names are reserved for Floppy Drives. C: is your internal HDD.
D: can either point to the Optical drive, or the USB. The normal convention is that the removable media is named from Z: backwards. Y: and Z: are usually used for Network drives, so X: should be your USB. First try with the change to "Professional". If it does not work,

After Security updation of Windows 7 in Boot Camp (Mac Book Pro with Retina Display) on 13-Nov-2013, Windows 7 Desktop Gadgets are not working properly.

After Security updation of Windows 7 in Boot Camp (Mac Book Pro with Retina Display) on 13-Nov-2013, Windows 7 Desktop Gadgets are not working properly.
This is boot camp problem, because in other normal notebooks (e.g. SONY VAIO, Lenovo with Windows 7) the gadgets are working normally.
I am attaching the screen shot of Desktop Gadgets and Security updates of Windows 7.
Kindly solve this issue ASAP.
Shailendra Gupta
<edited by host>

You are not addressing Apple, but a community of unpaid volunteers. So ASAP won't cut it. Also, you should refrain from posting personal information (like your email address) in the body of your comments, as this is part of the community usage guidelines.
Have you reinstalled the latest Boot Camp Windows 7 drivers, just in case Microsoft overwrote some of them during the Windows 7 security update?
If you want to communicate issues with Apple about Boot Camp and OS X, click on the link. Just don't hold your breath on receiving a response.

Installing Windows 7 With Boot Camp on Mac Pro 3.1 w/GTX285 Video card

I have an Early 2008 Mac Pro 3.1 running the latest version of OS 10.6 with all updates. I have an nVidia GTX285 card installed in the Mac Pro that has been working fine for at least six months under OS 10.6 with Mac drivers downloaded from the nVidia web site and installed under OS 10.6. I replaced the ATi 2600XT video card with the nVidia GTX285 in order to have CUDA support in Premier Pro CS 5 and it works beautifully.
I now wish to install Windows 7 Professional 64 bit on this Mac Pro. I have never had any version of Windows installed on this Mac Pro. I am using Boot Camp assistant and a new full version of Windows 7 Professional 64-bit.
My question is do I need to remove the GTX 285 graphics card and replace it with my AT 2600XT before installing Windows 7? This would be a real pain to do because the two connectors to the motherboard are hard to get to. However, since Apple never used the GTX285 in any of its computers, I am worried that I will not have any video display when I go to try and install Windows 7 with Boot Cam assistant.
Please advise me whether removing the graphics card is necessary before installing Windows 7 with Boot Camp.
Thank you in advance for responding.
Tom

NO.... he has a workstation, and not MBP, nor are "drivers already loaded."
How I would proceed -
Install Windows on its own drive.
Pull all the other drives.
Boot from Windows 7 Pro DVD
Forget Boot Camp Assistant, it doesn't do anything - unless you really want to install Windows on the SAME drive as Mac OS - not ideal and not what most of Mac Pro owners do.
Just insert your OS X DVD once Windows is up to date - helps to buy the SP1 OEM version $129.
Run Apple SETUP.exe (Boot Camp 3.0.x drivers) and update with ASU or manually to 3.2.
No you don't need to go back and use that ATI. And you dont' want to be in the situation of changing from ATI to Nvidia and all the hassle that adds. you are fine.
The Mac Pro is as close as anything to a standard Wintel workstation.
Add MS Security Essentials or KIS or whatever you favor. KIS2011 or NIS2011 are good, MSSE 2.0 is free and based on their enterprise product.
AV-Test.org Test Security-Software

Need help installing my graphics driver in windows vista via boot camp

New to mac so first time on forum as well.
Love the Mac but i also want to get on some old games. C&C The First Decade mainly.
I am currently using below.
Mac mini Mid 2011 processor 2.5 GHz Intel Core it
Memory 4 GB 1333 Mhz DDR3
Graphics AMD Radeon HD 6630M 256 MB
Software Mac OS X Lion 10.7.5
Installing windows vista home premium 32 bit
I have installed windows vista home premium using boot camp assistant and downloaded the windows drivers as well. After i have installed windows i installed boot camp using my Mac OS X snow leopard which installed boot camp 3 or 3.1 i believe and i eventually got apple updates for 3.2 which is what i am now runnning on vista. I had trouble getting my sound to play through my speakers at first but eventually got them working and now it is my graphics driver that i cannot seem to get working. In vista(I also downloaded service pack 1 and 2) when i go to control panel and check out my device control it shows a yellow exclamation point next to the adapter. I guess i need help in getting my graphics installed correctly on my windows. Is there something i should take off to install the correct driver? Or do i just need the correct driver download? If i have the correct driver how do i upload it onto my windows side in the device control.
When i try to run c&c generals/zero hour i get a directx 8.1 error, red alert 2 is black but i can hear. i know these games can work i installed the graphics correctly the first time when i did not have sound as this is my second time installing windows so the game did load when i did not have sound.
Advise?
I was thinking about saying forget this i can't waste hours of my time anymore but i have to be close to getting everything working if i had graphics before and no sound but sound this time and no graphics. I was also thinking about just buying windows 7 home premium sp1 64bit system builder dvd off amazon and reinstalling windows using windows 7 but i want to make sure i can play these games before i spend the money. I thought my mini couldn't support windows vista and if it did only boot camp 4? how am i getting this far to get things to work?
What is the driver i need to install to get these games working? What do I need to do or what am I missing???
Do i need to install a different boot camp off apple and find a driver that will get mine to work in vista?
Any and all responses will be greatly appreciated i have been at this everyday for hours.

Also is there something, say maybe a driver, that was installed i do not need that is blocking me from installing the correct drivers? What driver in my boot camp folder do i need to install to get to the correct display to run those games.

Can I install Windows 7 with boot camp on my computer, but install all my PC games for it on an external hardrive?

I have a new Mac, but I want to install Windows 7 with boot camp on it. However, I would only really be using it for gaming.
On another post, someone said that you could not install boot camp entirely onto an external hardrive. As boot camp would only be for gaming, then could I install all my games (when I'm given the option to chose the file of where to install) onto an external drive which is correctly formatted? (what is the format too?) Also, would USB 3.0 be ok, or would thunderbolt be a better option (hoping its USB)
Thank you

you will be fine and either are more than enough for even an SSD.
NTFS of course.
Might look thru Google to see if anyone has managed to boot Windows from Thunderbolt, I think someone managed after install and then made a restore image and placed on Tb storage device.

2010 Mac Pro Boot Camp - Refuses to boot Windows after installing Boot Camp drivers

Hey all,
I have a quad 3.2Ghz 2010 Mac Pro with a Radeon 5870 and 8 GB RAM.
I have 2 10000RPM WD Raptor drives, the first drive is my Lion boot drive. The 4th bay contains the second Raptor which has Windows 7 Ultimate 64 bit installed. Bay 2 has Time Machine, bay 3 has a Windows backup drive.
I had first installed Windows and the Boot Camp drivers a few months ago and everything was humming along smoothly. Monday I tried to boot into Windows and it crashed immediately after the black Booting Windows screen started to change to the login window. This happened repeatedly. Nothing changed on the system that I am aware of. Whenever I tried to boot windows again, it booted into the repair mode. That did not seem to work because after running the repair it would still not boot.
So I did what is usually required of Windows, and that was to reinstall. I reformatted the hard drive, ran Boot Camp assistant, and started the install.
Everything was peachy so far, so I tried to reinstall the Boot Camp drivers (4.0). Did a reboot. Same problem. Doh!
So I did ANOTHER reinstall, and everything was fine. But this time I tried to install the Boot Camp drivers off the os install disc that came with my Mac (3.1). Still no go!
So finally I did my third reinstall and after that I did not install Boot Camp drivers. However, I did load up the CD and individually installed drivers for the Apple Mouse, Apple Keyboard, Cinema Display, etc. No problems whatsoever. Everything is actually still humming along fine.
So it looks like running the full Boot Camp install for some reason no longer works. Which means I am missing the Apple Boot Camp control panel, but that's not really a big deal. Althought it's quite annoying to not have the functionality of the special Mac keyboard keys like volume control, etc.
Has anyone run into this? I thought it might be a hardware problem but my Mac OS X OS exhibits no problems whatsoever.
Thanks!

Thank you to The hatter.
I have a Mac Pro mid 2010 with a SSD and several internal hard disks. For some time I was trying to install Windows 7 on a fresh boot camp volume on a new WD 7200rpm 1TB hard disk. It was taking hours to install, and then I had a series of failures to reboot that proved permanent. The Window Repair utility would come up and took forever to repair the volume - but failed to actually do so, requiring completion reinstallation of the bootcamp volume. This occurred three times, between 1 day and 2 months after installation. I had already moved the Windows drive in to drive slot 1 of the Mac Pro.
Eventually I gave up and installed boot camp on a secondary partition of the SSD. This worked fine, however is limited in capacity. So yesterday I thought I would try to install Windows on the hard disk again. The Windows installer took many hours to do its thing, and eventually a message came up that the installation had failed.
I took your tip about possible hard disk failure, and ran Techtool Pro surface scan. It turns out that there are lots of bad blocks being reported. According to Micromat's documentation, the bad blocks being reported are those that may be in critical areas of the disk that cannot be mapped out. They recommend low level reinitialisation (with zeros) to map out the bad blocks, if possible. I am now running Apple's Disk Utility to do this, and fingers crossed that this reinitialisation succeeds, or I will have to replace the drive.

Can I install Windows 7 with boot camp, but install all my PC games for it on an external hardrive?

I have a new Mac, but I want to install Windows 7 with boot camp on it. However, I would only really be using it for gaming.
On another post, someone said that you could not install boot camp entirely onto an external hardrive. As boot camp would only be for gaming, then could I install all my games (when I'm given the option to chose the file of where to install) onto an external drive which is correctly formatted? (what is the format too?) Also, which would allow for a faster gameplay, USB 3.0 or Thunderbolt? as fast gameplay is important
Thank you

How to move steam to another drive:
Delete everything in the Steam folder except for the "steam.exe" and the "steamapps" folder
Move the steam folder over to the secondary drive you want it on
Open the "steam.exe" and it will reconfigure steam
Log in and BAM! All your games are recognized
Now, you can put what ever games you want on the SSD with Steam Mover (or junctions)
Create another folder on the C:\ drive and name it (C:\Users\Sean\Steam Games)
Run Steam Mover and have it move the game to that location and you are done!
Now go play the games you want!
How to have steam on the SSD while having the games on either the SSD or HDD:
Delete everything in the Steam folder except for the "steam.exe" and the "steamapps" folder
Have the "steam.exe" to a folder made on the C:\ drive (C:\Users\Sean\Steam)
Have the "steamapps" folder on the HDD you want to store your games (D:\User\Program Files\Steam\steamapps)
Make a junction from the "steamapps" folder to the SSD folder with the "steam.exe" in it
Open the "steam.exe" and it will reconfigure steam
Logged in and BAM! All your games are recognized and steam is on the SSD and the games on the other drive.
Now, you can put what ever games you want on the SSD with Steam Mover (or junctions)
Create another folder on the C:\ drive and name it (C:\Users\Sean\Steam Games)
Run Steam Mover and have it move the game to that location and you are done!
Now go play the games you want!

Time Capsule issue with backing up Windows partition via Boot Camp

I just bought the macbook pro and time capsule. I set up a 25GB Windows partition using Boot Camp and I have set up a Time Capsule to handle the backups. Time Capsule seems to backup the OSX hard drive partition fine, with the historical versions of the drive displayed correctly. However, with the Windows partition the Time Capsule appears to be backing up any files that change, however there is no version control showing up in Time Machine. In other words, I ONLY see the Windows partitioned drive as backed up in the "Today (Now)" screen. Any historical dates the drive shows up shaded and I cannot access it. Is there a way for Time Machine to manage the Windows partition in the same way as it does for MAC OSX drives?
John

Why is it so hard?
1000 and 1 times: the drive must have FREE contiguous unfragmented space and some files are blocking and preventing.
Some are able to find and delete, some by booting from another hard drive or OS X DVD to repair and/or run iDefrag.
Or.... backup; erase; and restore.
ie, CLONE your hard drive in both directions. My choice would be SuperDuper or Carbon Copy Cloner. They tend to work. Defrag tends to be slow and if there is no backup and there is an error.... well, you'll find out.
Apple error message is badly and poorly worded. Said so for over 3 yrs and it has not changed or improved though.
Paragon CampTune 9.5 $19 is great for Boot Camp. And resizing. And Windows 7 may need 2 or 3x what the base minimums listed. 32-48GB at least to be safe. And those are conservative numbers.

I'm running windows XP using boot camp. What key do I push on the keyboard to bring up my desktop?

I'm running windows XP using boot camp. What key do I push on the keyboard to bring up/go to my desktop?

Have a look here http://en.wikipedia.org/wiki/Table_of_keyboard_shortcuts
Stefan

Windows not finding Boot Camp on MacBook Pro

Hey everyone. I have Windows 7 64-bit and a MacBook Pro (mid 2010) with OS X Lion installed. When I boot up in Windows, it seems that only half of the time Windows realizes that it is on a Mac. Meaning...only half of the time the Boot Camp program is running in the notification tray, and only half of the time will Windows register the volume up/down, brightness up/down, and keyboard backlight up/down buttons on the Mac. It makes it very difficult to say...adjust the brightness or volume in the middle of a game. I can still go out of the game and turn up the volume in the notification area, but it is becoming a huge hassle. Like I said, this is only happening about half of the time. The other half of the time Windows registers that Boot Camp is on it, there is the Boot Camp icon in the bottom right corner of Windows, and all of my control buttons (brightness, volume, etc.) work just fine. Any ideas on how to make this happen every time? Thanks.

Hello Bhagyeshree
Check out the articles below to troubleshoot issues with connecting to Wi-Fi. Start with creating a new Network Location and then search for a Wi-Fi network and if that does not work, then go through second article to troubleshoot the issue further.
OS X Mavericks: Add a network location
http://support.apple.com/kb/PH13788
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
Regards,
-Norm G.

Can i use an external hard drive in windows to add additional storage after my initial partition is set up. i want to add a 500 GB hard drive to use with my windows. I set windows up in boot camp with a 50 GB partition?

can i use an external hard drive in windows to add additional storage after my initial partition is set up. i want to add a 500 GB external hard drive to use with my windows. I set windows up in boot camp with a 50 GB partition? I now want to add another 500 GB?

Yes. Windows supports external USB drives.

Error 0x80070017 when installing Windows 7 via Boot Camp...

I've been trying hard to research this issue and haven't come across anything that has worked for me.
At work, we have an iMac (Early-2009) that we wish to install Windows 7 on. Previous user has left, so I reinstalled Snow Leopard (10.6) and used Disk Utility from the disc to reformat complete to GUID single partition Mac OS Extended (Journaled), which is pretty standard for Macs. Mac OS X installed and booted just fine. I updated completely to 10.6.8 and all other updates. Only installed Microsoft Office 2011 and Firefox.
So Boot Camp begins...
Found that the early-2009 model doesn't "support" Windows 7 64-bit, so we are fine going with 32-bit. The 32-bit Windows 7 disc has been used to install Windows 7 using Boot Camp on 2 Mac Mini's (one Intel Core Duo, the other one Intel Core 2 Duo) just a few days ago.
Opened Boot Camp Assistant, partitioned the 1TB drive equally, inserted the Windows 7 disc, and clicked Restart.
It boots from the Windows 7 disc, I go through the options, choose the BOOTCAMP partition and format it (I assume Windows 7 is choosing NTFS for me). Click next.
It copies the files instantly, but then "begins" to Expand the files. It remains at 0% for 5-10 minutes (I can hear the Windows 7 DVD spin down and spin up, but mostly spin down). That's when the error hits:
"Windows cannot copy files required for installation. The files may be corrupt or missing. Make sure all files required for installation are available, and restart the installation. Error code: 0x80070017"
I click Ok and cancel the install. Restart and boot back into Mac OS X. And here I am.
Important Notes:
I've tried multiple times with a 64-bit disc as well. I will likely go check out another 32-bit disc from our software department, but I know this disc works on other Macs.
This issue occurred a month back as well when we attempted to install Windows 7 via Boot Camp (so before the hard drive and OS were reformatted and reinstalled). I was hoping reformatting and reinstalling the Mac OS X would solve the issue.
The Superdrive appears to be working just fine.
I read somewhere that I need to use repair disk to fix it. Does anyone know if I can repair disk a NTFS partition? Or am I suppose to repair disk the parent drive itself? The place I read it wasn't specific AT ALL and the forum was closed and I couldn't find a way to get a hold of the person. It just said "Repair disk did the trick". People, if you find a solution to your own problem, POST the solution!
Thanks in advance!

Yea, I saw that kb article. I verified we have the early 2009 iMac. It's an iMac 9,1 (3.06 24-inch, A1225).
As far as different hardware, I really don't think so, but I'll have to double check with my fellow employees. The specs all match up, but I'll see if anyone remembers having to replace hardware or send it into Apple.
I did think of trying an external DVD drive too, I'll see if I can scrounge one up. I'll post if it works or not.
The employee using the machine knows Windows, but is willing to learn the Mac OS X. Diversify your experiences I always say!
An added note to the Repair Disk "solution". Turns out you can't run Repair Disk on NTFS partitions or the parent hard drive that contains that partition, which makes since. I can only run Repair Disk on the HFS+ partition which did no good. (This is, of course, from booting up using a Mac OS X Install DVD).
Mac_Win, thanks for the suggestions!

Can I use my old Macbook Pro as an external disc drive while installing Windows 7 through boot camp?

I want to install the Windows 7 CD on the newest version of the 2013 Macbook pro 10.9.2 running OSX Mavericks, through Boot Camp. It does not have a disc port, nor do I have an external disc drive....but I do have an older macbook that does have a disc drive and I know you can supplement it for an external disc drive.
My question is can I use my old Macbook pro's as an external disc drive for the installation of Windows 7 in Boot camp? Will this be a problem? Or do I have to buy an external disc drive separately.

http://support.apple.com/kb/HT5287

Installing Windows 7 in Boot Camp with iso

I have downloaded an .iso file with Windows 7 on but I can't install it in Boot Camp. I've tried several things with no luck.
1. For the first, when I start up Boot Camp assistant I can't choose to "Create a Windows 7 install disk". I only have the two bottom options, the one for downloading support software and the one for installing windows 7. So I can't use my .iso file there.
2. I tried to burn a bootable dvd with the .iso file. I burned it on a Windows PC since my superdrive won't burn on the discs I've got (DVD+R). The disc works properly on the Windows PC but when i mount it in my Macbook I only get a popup that says I've put in a blank disc and some options of what I wan't to do next.
3. I tried to make a bootable flash drive and that pops up in finder, but the Boot Camp assistant won't recognize it and says I have to put in a Windows 7 install disc.
4. I also tried to open the image file in disc utility, but the result is the same as if I'm trying with a flash drive.
I'm out of ideas now so it would be nice if someone else knew any other possibilites to install Windows 7 in Boot Camp.
Or maybe there is an solution for the things I've alleready tried?
I'm using a MacBook Pro late 2008

Does it boot off the internal?
Is the external a full copy of your working system?> whew! then you can always wipe it clean and start over.
As long as the partition was created properly.... though 50GB can work it can also be slim fit in the end.
Under the worst condition - and the Mini is one of the worst, too - two minutes maybe to restart.
External because there never was an internal DVD player?
zap pram.
did you buy DVD or burn DVD? if burned, then that is likely cultprit Redo at slowest burn speed (2x) with verify.
Heck, even Windows 7 SP1 has been implicated on some were pre-SP1 worked.
For a test, there is Windows 8 RP for free. And Parallels 7 will set up a VM for you with the whole download and inistall. Not everyone needs to run natively.

Windows 10 in Boot Camp Thunderbolt Display

Similar Messages

Maybe you are looking for