Windows 2003 DHCP server merge to Solaris 10

Does anyone ever tried to merge a Windows2003 DHCP server to Solaris 10? Especially running this DHCP server in a solaris zone?
I have an old windows 2003 server with 100 DHCP clients that needs be be transported to Solaris so we can get rid of this Windows machine.
Is it possible to read the DHCP backupfile from windows2003 with Solaris?

Troy H wrote:
> Hi,
>
> I have an issue where I do not see SLP being deployed successfully from
> a Windows Server's DHCP scope options. All of the other options come
> through.
>
> I followed this MS doc: http://support.microsoft.com/kb/285019
>
> As far as I can tell, it's setup correctly.
> Has anyone else setup SLP Options in MS and gotten them to work?
> Thank you,
> Troy
Okay, more information:
Workstations that are imaged will receive SLP information as long as the
Zen agent hasn't been installed.(using latest Zen7SP1 Postpatch)
Once you install the Zen agent you will no longer receive SLP via DHCP.
Note that the Novell Client version can be 491 to 491 SP3.
However, if you rename the C:\windows\system32\novell\novdhcp.dll file,
you'll resume getting SLP info from DHCP.(TID 10093676)
Pretty strange, eh?

Similar Messages

Cisco vlan setup w a windows 2003 dhcp server help

Can anyone give me some tips or point me to some documentation on setting up a catalyst 4500 series w vlans and a windows 2003 server w associated dhcp scopes? Just for curiosity, what is a good vlan design for a college. I was thinking a student, a staff, a faculty, and a guest and or mgmt vlan. Also, on the guest vlan how would I setup an outbound acl to only allow port 80 traffic? Thanks in advance.

Hi
Try to limit the number of users per vlan to no more than a class C subnet if you can. We use half a class C /25 network in our offices.
If you can break up the vlans to match the different type of users then that would be a good start. It means you can further down the line apply different security policies to the different vlans which in your situation you may well want to do. Don't worry if for example you need to use 2 or 3 vlans for students it's not a problem.
Attached is a link for 4500 configuration. You need to look at the following chapters primarily
1) Configuring VLAN's VTP & VMPS.
2) Configuring Layer 3 interfaces. Look at the section on logical layer 3 SVI's.
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/31sg/configuration/guide/conf.html
On the guest vlan you would need something like (assuming guest vlan subnet range is 192.168.1.0/24
access-list 120 permit tcp 192.168.1.0 255.255.255.0 any eq www
access-list 120 deny ip 192.168.1.0 255.255.255.0 any
and apply it on the inbound vlan interface. ie. if your vlan for guest users is vlan 20
switch(config)# vlan 20
switch(config-if)# ip access-group 120 in
As for the W2003 server, not done much with windows. You will need DHCP manager which should be under admin tools. Make sure you exclude the addresses for each subnet that you allocate to the 4500 layer 3 interfaces ie
switch(config)# vlan 20
switch(config-t)# ip address 192.168.1.1 255.255.255.0
In your DHCP scope 192.168.1.1 will be the default gateway for your clients and you should exclude this from the scope.
Hope this is enough to get you started
Jon

CA and Certificate Issue in ACS 4.0 For Windows 2003 Enterprise Server

Hi,
I have configured Microsoft CA server on the same ACS 4.0 for Windows 2003 enterprise server which was configured earlier using the self generated certificates for EAP and PEAP authentications.
After I change the certificate from self generated to the new CA certificate that can be viewed under install ACS certificate option on ACS server but having the following problems
1. SSL is not functioning while internet browser access to the ACS server and going through http instead of https.
2. Wireless clients are authenticated successfully even after the certificate is uninstalled.
Any help on these problems will be appreciated.
Thanks
Best Regards,
Ahmed

Hi Rohit,
Thanks for reminding the HTTPS option under Administration Control on ACS.
I have some doubts pertaining to installation of certificates on Wireless clients though it is optional for Self Generated Certificates but what in case of Mirosoft CA as I tested wireless client authentications even after removing the certificate from microsoft supplicant WindowsXP SP2 having installed the patch KB885453 for PEAP. How the certificate on wireless client works.
Is it mandatory or optional to keep certificate on Wireless Clients as they could able to get authenticated through ACS after removing the certificate.
Thanks
Best Regards,
Ahmed

Windows 2003 Terminal Server, ZEN 7, and WSUS

Hi,
We're having a problem getting a group policy to "Stick" in Windows 2003
terminal server. The server(s) have the ZEN 7.01 agent installed per
the TID's for a terminal server. We believe we've set all the Group
Policies of the users that login to these systems, yet once they are
rebooted, the WSUS update server location resets to the default
(update.microsoft.com). This is set in gpedit in:
\computer configuration\administrative templates\Windows
Components\Windows Update
Is this settable in a user package, or should this be done in a
workstation package? If so, could we "force" the workstation package to
override the Windows Update settings for all users, regardless of what
user policy package they have?
Thanks for any ideas!
Greg

In the Properties of the WS Group Policy, there is an option to set "Loop
Back" so that the Computer GPO is set last.
Craig Wilson - MCNE, MCSE, CCNA
Novell Support Forums Volunteer Sysop
Novell does not officially monitor these forums.
Suggestions/Opinions/Statements made by me are solely my own.
These thoughts may not be shared by either Novell or any rational human.
"Greg Palumbo" <[email protected]> wrote in message
news:rFFZk.5166$[email protected]..
> Hi,
>
> We're having a problem getting a group policy to "Stick" in Windows 2003
> terminal server. The server(s) have the ZEN 7.01 agent installed per the
> TID's for a terminal server. We believe we've set all the Group Policies
> of the users that login to these systems, yet once they are rebooted, the
> WSUS update server location resets to the default (update.microsoft.com).
> This is set in gpedit in:
>
> \computer configuration\administrative templates\Windows
> Components\Windows Update
>
> Is this settable in a user package, or should this be done in a
> workstation package? If so, could we "force" the workstation package to
> override the Windows Update settings for all users, regardless of what
> user policy package they have?
>
> Thanks for any ideas!
> Greg

I dream of running Dreamweaver on a Windows 2003 Terminal Server

I have a "volume" license and attempted to install Dreamweaver CS4 on a Windows 2003 Terminal Server. I get an error message right away indicating that the system does not meet the minimum install requirements, ie XP/Vista.
Adobe volume licensing team verified that it is the correct license for installing on a terminal server, but after one hour of what would a bad nightmare with adobe "no" support (Outsourcing issue, failure to grasp and process the basic error message) I got no where and am having to resort to the forums. I have googled on this and got no where and nothing on the search efforts on this site.
If anyone has an idea of what is going on, bug, wrong install media, please clue me in.
Thanks!

pziecina
Thanks for the information. We do have AppV here and tried that approach. While this gets us past the install minimum requirements, it does not resolve the issue of running of more than one instance at a time, per terminal server, even though our volume license allows for it.

SGA_TARGET SIZE 3GB in 10g Release 2 server on windows 2003 E Server?

Is it possible to increase the SGA_TARGET greater than 3 GB on Windows 2003 Enterprise server(32-bit)?
OS version : Microsoft Windows 2003 R2 Enterprise Edition
Service Pack 2
Bit Version : 32 bit
Computer(SERVER) : Intel(R) Xeon(TM) CPU 3.60GHz
3.59GHz, 15.5 GB RAM
Physical Address Extension
DataBase Version : Oracle 10g Release 2 (10.2.0.1.0)

hi,
As suggested earlier , please go through following notes as it will help you understand the concepts clearly
Note:342080.1. This note talks in detail on how to use more than 4GB RAM on Windows.
Note:225349.1 Implementing Address Windowing Extensions (AWE) or VLM on Windows Platforms
You can not set SGA_TARGET greater then 2.7 G on windows 32 bit machine. Yes , you can have SGA greater then 3 Gb but by using AWE which requires to unset SGA_TARGET and use db_block_buffers instead of db_cache_size.
-Amit
http://askoracledba.blogspot.com/

Oracle ODBC Driver (Windows 2003 x64 Server)

Hi all
I have some trouble with this ODBC Driver ...
I have installed Oracle Client 10.2.0.1.0 with the ODBC Driver and SQLplus etc.
Now I have configured in the "Net Manager" some "Service Naming" as I did
on other servers before. Then I Test the connection in the "Net Manager" it
seams to work fine.
When I now try to connect in SQL Plus the following error comes up:
ORA-12154: TNS:could not resolve the connect identifier specified
I did already do this:
- Add "...\NETWORK\ADMIN" to the Path Variable of the server
- sqlnet.ora looks like:
SQLNET.AUTHENTICATION_SERVICES= (NTS)
NAMES.DIRECTORY_PATH= (TNSNAMES)
- tnsnames.ora looks like:
MyName.WORLD =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = myDomain.net)(PORT = 1521))
(CONNECT_DATA =
(SID = DBSIDxx)
What do I have to do to get this working ???
Thanks for any comments!
Best regards
Frank Uray

Nevermind, I think I'm to assume that this is the same as:
Re: unable to use SQL Plus (Windows 2003 x64 Server)

IDES 4.7 Installation under Windows 2003 Enterprise Server, Xeon 64 bit

Dear all,
we are just trying to install IDES 4.7:
IDES 4.7 Installation under Windows 2003 Enterprise Server, Xeon 64 bit
But the installation break with error Message:
Error 5 (Access is denied.) in excution of a "NetServerGetInfo" function, line (233), with parameter (saptranshost, 101).
MOS-01224 Failed to add privileges "NetcbPrivilege SeAssignPrimaryTokenPrivile SeIncreaseQuotaPrivilege to account ....." ....
FJs-00012 Error when excuting script....
Any experience or help from your side?
Thanks in advance
HanseAtik

Hi. First login in your server with user "sid"adm after go to START --> RUN --> CMD
adn execute "R3trans -d" Tell what result .
About documentation read -->
service.sap.com/~form/sapnet?_SHORTKEY=00200797470000065912&
in left corner chek your release like :
"SAP R/3 Enterprise Core 4.70 / Ext. Set 2.00 (SR1)"
After read the document for your release, for example if you use the Oracle on WIn and R/3 Enterprise 4.7 x 2.00 SR1 -->
Inst. Guide - R/3 Enterprise 4.7 x 2.00 SR1 on Win: Oracle
Regards.
Edited by: Sergo Beradze on Mar 21, 2008 10:55 AM

Cannot install jwsdp-1.2 on Windows 2003 Enterprise Server

Hello,
We are trying to install jwsdp-1_2-windows-i586.exe on a Windows 2003 Enterprise Server system, but unfortunately we are not able to do this.
Even worse the installation program simply stops without any message at all. So we have no clue how to proceed. Any help would be appreciated.
Greetings,
Erwin.

Yes,
I have attached the output, but the installation just stops..
Greetings,
Erwin.
D:\install>jwsdp-1_2-windows-i586.exe -console
Initializing InstallShield Wizard...
Searching for Java(tm) Virtual Machine...
Searching for Java 1.3.0 by IBM Corporation
Verifying Java 1.3.0 by IBM Corporation
Verifying Java 1.3.0 by IBM Corporation
Verifying Java 1.3.0 by IBM Corporation
Verifying Java 1.3.0 by IBM Corporation
Verifying Java 1.3.0 by IBM Corporation
Verifying Java 1.3.0 by IBM Corporation
Verifying Java 1.3.0 by IBM Corporation
Verifying Java 1.3.0 by IBM Corporation
Searching for Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Verifying Java 1.3.0 by Sun Microsystems
Searching for Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Verifying Java 1.3.X by Sun Microsystems
Searching for Java 1.4X by Sun Microsystems
Verifying Java 1.4X by Sun Microsystems
D:\install>

Is is possible to add Windows 6 64-bit drivers to a Windows 2003 print server?

We are having some trouble figuring a way in which to support network printing for Windows 7 64-bit machines that we are starting to intermittently put out in what, as of this moment, is still primarily a native XP 32-bit environment. Our concern has been that, if we replace the drivers on the print server to the Windows 7 64-bit drivers, then the XP machines will then pull down those drivers and then not be able to print any longer. According to Microsoft, the way around this is to utilize the "Additional Drivers" area within the properites of the printer. From there, in theory, you can add a new driver that uses "x64" as the print processor. However, when we attempted to do this on our legacy Windows 2003 print server (which I believe to be 32-bit) we noticed that, in the "version area" of the selection for the x64 print processor, Windows 7 is not listed. We then receive the following error message after we attempt to go forward and add the driver. . .
-Selected printer driver not found
The specified location does not contain the driver HP LaserJet 4050 Series PCL6 for the requested processor architecture
It looks to me that the problem is in that the server is Windows 2003 and we are attempting to make Windows 7 drivers work within that framework. Can someone please confirm this suspician or instruct us further?
Thanks,
-Brian McKnight

Gotcha!!
I am done with mounting a secondary HDD (thanks to ifixit) and installing Windows 8 Pro 64 bit on it without a worry. Charm, charm!!
Boot Camp 5 guide prescribes all needed steps and when read and used correctly, installation must be an easy task. And all the existing apple hardwares work so good in the Windows environment too.
I am going to help out a friend of mine in doing a similar thing on his mac too. If you got specific questions, please do shoot up here and i should be able to get a reply to it (if at all).
Thanks everyone.
~ Narey

Satellite A100-906 PSAA9E: I cannot find drivers for Windows 2003 R2 Server

I found and installed some drivers from http://ru.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=RU
Look at the screenshots of my computer please.
"Device Manager" window:
http://www.disa.ho.com.ua/toshiba/1.GIF
http://www.disa.ho.com.ua/toshiba/2.GIF
http://www.disa.ho.com.ua/toshiba/3-1.GIF
http://www.disa.ho.com.ua/toshiba/3-2.GIF
http://www.disa.ho.com.ua/toshiba/4-1.GIF
http://www.disa.ho.com.ua/toshiba/4-2.GIF
http://www.disa.ho.com.ua/toshiba/5-1.GIF
http://www.disa.ho.com.ua/toshiba/5-2.GIF
How can I solve this problem?
ps: sound not working

Hi
As mentioned above you will not find Toshiba drivers designed especially for the Windows 2003 R2 Server.
But dont worry and dont give up.
The simply Windows XP drivers should be compatible and you should be able to install the Xp drivers on the Win2003 Server OS.
good luck

Windows 2003 business server network printer - please help

A customer has a windows 2003 business server and several XP machines. I have put the driver on the server and shared it. Set up all the windows pc and print no problem. They have three mac osx and im stuck! I believe that ive installed the driver ppd??? and followed the instructions correctly!!! but when i print from the mac it just prints loads of garbage??? i think i need a postscript chip installed on the infotec2046 printer??? is there another way - please>>>

You should be able to use the HP Laserjet 6 Series driver included in OS X.
http://www.openprinting.org/show_printer.cgi?recnum=Infotec-IS2045

Locked files using a Windows 2003 File Server with Mac 10.6 clients running CS5

We migrated 40 Mac users from OS X 10.5/CS3 to OS X 10.6/CS5 back in November. Our InDesign files are kept on a Windows 2003 file server.
We have had fairly constant complaints of InDesign and Photoshop files being reported as locked when users try to save their work back to the server. This did not occur as frequently with CS3.
Has anyone else had this issue?

I'd suggest starting with iFelix's Sharing files between a Windows XP PC and a Mac running OS 10.4.x

VPN and Windows 2003 DHCP

I have an 871 Router that I am trying to setup a VPN but the Windows 2003 server on the network does the dhcp. At this point I get and error on authentication just trying to vpn - here is the config I hope someone can help. I have never had this problem before
aaa authentication login default local
aaa authentication login sdm_vpn_xauth_ml_1 local
aaa authorization exec default local
aaa authorization network sdm_vpn_group_ml_1 local
aaa session-id common
resource policy
ip subnet-zero
ip cef
ip domain name xxx.com
ip name-server 216.x.x.x
ip name-server 216.x.x.x
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp client configuration group xxxvpn
key xx2cisco
dns 192.168.0.1 216.x.x.x
domain d2b0411
netmask 255.255.255.0
crypto ipsec transform-set xxxvpn esp-3des esp-md5-hmac
crypto dynamic-map SDM_DYNMAP_1 1
set transform-set peruvpn
reverse-route
crypto map SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1
crypto map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1
crypto map SDM_CMAP_1 client configuration address respond
crypto map SDM_CMAP_1 65535 ipsec-isakmp dynamic SDM_DYNMAP_1
interface FastEthernet4
description $ES_WAN$
ip address 216.x.x.x 255.255.255.248
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map SDM_CMAP_1
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 192.168.0.254 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
ip local pool SDM_POOL_1 192.168.0.220 192.168.0.225
ip classless
ip route 0.0.0.0 0.0.0.0 216.x.x.x
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source static udp 192.168.0.1 3389 interface FastEthernet4 3389
ip nat inside source route-map SDM_RMAP_1 interface FastEthernet4 overload
access-list 100 remark SDM_ACL Category=2
access-list 100 deny ip any host 192.168.0.220
access-list 100 deny ip any host 192.168.0.221
access-list 100 deny ip any host 192.168.0.222
access-list 100 deny ip any host 192.168.0.223
access-list 100 deny ip any host 192.168.0.224
access-list 100 deny ip any host 192.168.0.225
access-list 100 permit ip 192.168.0.0 0.0.0.255 any
no cdp run
route-map SDM_RMAP_1 permit 1
match ip address 100
Thanks
Gabrielle

OK - I am able to VPN in fine now. I can ping the server 192.168.0.1- I can get in Remote Desktop to the server 192.168.0.1 and from remote desktop I can ping my VPNed Pc IP of 192.168.0.200. However, I can't see the domain when I go to map network or Network neigh. Any Ideas?
Thanks

Windows 7 Professional using a Windows 2003 print server to map printers

I am testing Win 7 in our network, I can install a network printer (HP Laserjet 3700 64bit driver) directly to the computer via TCP/IP. If I install the same driver on the 2003 R2 server (by adding the driver under sharing and additional drivers) it will not work, I get an Operation Failed with error 0x00000bcb.
Win 7 will be useless if I cannot connect it to the network for printing using a print server.
Thank you in advance,
Bill

SCENARIO:
Print Server
Windows Server
2003
R2, station
Windows
7 with
64-bit
and
HP LaserJet
P4015n
PROBLEM:
Windows
7 64-bit
stations
can not add
HP
LaserJet P4015n from
print server
Windows Server
2003
R2 showing the
error
0x000007e
SOLUTION:
In the
print server,
delete
the registry key
"HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows
NT\CurrentVersion\Print\Printers\[PrinterName]\CopyFiles\BIDI"
CAUSE: The station of user
was trying to
access a
path that the
64-bit
operating systems
do not recognize
as valid:
"spool\drivers\w32x86\3".
This
path is
set in the
printer settings
on the Print Server.

Windows 2003 DHCP server merge to Solaris 10

Similar Messages

Maybe you are looking for