Windows 2008 r2 WSUS port 8530

WINDOWS 2008 R2
new install of WSUS server 3.2.7600.251 want to change the port to 8530 from 80
But when I open command prompt and run wsusutil usecustomport true.....I get error :
C:\Program Files\Update Services\Tools>wsusutil usecustomwebsite true
Fatal Error: Exception has been thrown by the target of an invocation.

Hi,
Did you stop the WSUS service before you change the port?
If no, please try to stop the WSUS service with the command below first:
net stop wsusservice
After change the port, run the command net start wsusservice to start he WSUS service.
Besides, do not forget to change the WSUS GPO settings.
Best Regards.
Steven Lee Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Similar Messages

New WSUS install does not respond to clients over ports 8530 or 8531

I've recently installed WSUS on a Server 2012 machine, and am struggling to get it to respond to requests from other hosts. I cannot get it to respond to any host in any manner, except for requests from itself.
My setup is as follows:
WSUS installed on a Server 2012 domain controller, DC01.
Other roles installed include AD CS, AD DS, DNS, IIS, and Print Services.
WSUS is using all default settings.
The firewall has inbound and outbound exceptions for ports 8530 and 8531
A bit of information about what's happening:
IIS will respond over port 80. I can open a Web browser from my workstation and connect to http://dc01/. If I attempt to connect to http://dc01:8530 (which I know should not work, but
should respond with a 403 error), it times out. Identical behavior is observed over port 8531 with https.
IIS will respond with a 403 if I make this same connection in a browser on DC01, it will work if I connect using either the loopback IP or hostname, but will time out if I attempt to make the connection using the server's local IP (IPv4).
If I try to connect from my workstation using the WSUS configuration snap-in, I get an error: The remote server could not be contacted. Please verify that IIS on the server is correctly configured and is running.
If I try to connect from DC01 using the WSUS configuration snap-in, it works correctly.
The above is true for both http (8530) and https (8531).
IIS logs show inbound connections from my workstation and show that IIS is responding with a 200. However, Wireshark running on DC01 shows three attempts by my workstation to open a connection -- three SYN packets, one initial attempt then two identical
retries -- over a period of about ten seconds, with no responses from DC01. If IIS is responding, the responses are getting lost sometime before they hit the NIC.
Bindings in IIS are correct, 8530 for http and 8531 for https.
Given that everything works fine when making a local connection, I think I can safely assume that WSUS itself is running properly, and the issue is related to IIS. Nonetheless, in the hopes of this simply being a failed install, I have uninstalled and reinstalled
both IIS and WSUS multiple times. (One thing to note, though I doubt it's related: WSUS consistently fails to set the path for the local update cache, failing the post-deployment configuration. I have to manually edit the UpdateServices-Services.xml file to
include the path for the local cache. Everything goes fine after I do that.)
I'm pretty stumped on this, and would happily accept any help. Thanks!

I've recently installed WSUS on a Server 2012 machine, and am struggling to get it to respond to requests from other hosts. I cannot get it to respond to any host in any manner, except for requests from itself.
My setup is as follows:
WSUS installed on a Server 2012 domain controller, DC01.
Other roles installed include AD CS, AD DS, DNS, IIS, and Print Services.
Fundamentally you have two issues here:
The first is the question of co-existence between WSUS and AD CS.
The second is whether this machine was a DC before, or after, you installed WSUS.
With Windows Server 2003 systems, running 'dcpromo' after installing IIS (and WSUS) would break IIS (and thus WSUS). With Windows Server 2012, installing WSUS with the AD DS role present results in a broken WSUS installation (if not an outright installation
failure). This is because on a WS2012 Domain Controller, there are GPO restrictions on "Log On As A Service" which impact the ability of certain LOCAL accounts to do so ... one of which being the Network Service which is required for WSUS and another local
use account, which is used for WID.
Regarding ports and IIS -- WSUS is designed to work on port 8530 by default on a Windows Server 2012 box. It can also be made to work on port 80, but you have to use the correct utilities and procedures to make that change. As for your observation
that "port 6000" seems to be a cutoff.... I'll (re)direct your attention to the installation of Active Directory Certificate Services, which I suspect is a contributing factor, and in general firewall configuration rules -- which are probably the most likely
culprit on the port range of 6000+ (not including 8530 which I promise you is open by a rule explicitly created by/for WSUS).
So, here's my suggestion:
Install the WSUS role first.
Install the AD DS role if you must (but Domain Controllers should not also be web or application server).
Install the AD CS role elsewhere.
Lawrence Garvin, M.S., MCSA, MCITP:EA, MCDBA
SolarWinds Head Geek
Microsoft MVP - Software Packaging, Deployment & Servicing (2005-2014)
My MVP Profile: http://mvp.microsoft.com/en-us/mvp/Lawrence%20R%20Garvin-32101
http://www.solarwinds.com/gotmicrosoft
The views expressed on this post are mine and do not necessarily reflect the views of SolarWinds.

Huge Sized download taking place at port 8530 between clients and WSUS\SUP of secondary site

Hi Guy's
Need a solution to the issue, the SCCM 2012 clients under a secondary site { Secondary site with SUP\WSUS } are downloading 200Mb + data at port 8530. This seems quite abnormal.
Need to know answer of below
1- Actual size of catalog what clients should download or path where on WSUS is stored
2- How to restrict a huge sized download between WSUS and CM 2012 client
This is not the case where clients are directly reporting to Primary size.
Regards
Sushain Kapoor
Regards Sushain KApoor

Hi Jason
Just a little clarity, will the client download information for a particular product or all the products selected in wsus.
Eg: Windows 7 systems will download the catalog information of Windows 7 only against selections made in WSUS. Or it will download the windows XP and windows vista and other product information also. This particular question i am asking as i see only 300
updates as found in windowsupdate.log and not the thousands synced in WSUS
Is the update metadata exported using the wsusutil.exe the actual catalog size what clients are downloading
Regards Sushain KApoor

Windows 2008 Server contacting multiple public IP on port 80 and 443

Windows 2008 Server contacting multiple public IP on port 80 and 443
Source : Microsoft Lync 2010
Port : 80
Destination : unknown.prolexic.com
Source : Internet Explorer
Port : 80
Destination :a-0001.a-msedge.net
Source : Internet Explorer
Port : 443
Destination :204.79.197.200
Is this virus? how to stop the same?

Org name of the IP shows Microsoft Corporation
Since its hits on firewall , i will have to stop the same
but not sure for what its being contacted to these Ips
OrgName: Microsoft Corporation

Unable to install security updates via WSUS on Windows 2008 client servers

When I try install to install updates on Windows 2008 client servers I get the error : Code 80244019 Windows Update encountered an unknown error
After running the WSUS Client Diagnostic Tool I get the result : GetFileVersion(szEngineDir,&susVersion) failed with hr=0x80070002 The system cannot find the file specified.
On a Windows 2003 server the WSUS Client Diagnostic Tool shows no error message. So I guess the problem seems to be specificly related to Windows 2008 servers.
The client server has been integrated into a WSUS console version 3.2.7600.226 runnning on a Windows 2003 Enterprise Edition SP2.
Thanks in advance for the help in resolving this issue.

When I try install to install updates on Windows 2008 client servers I get the error : Code 80244019 Windows Update encountered an unknown error
The 0x80244019 error is an HTTP 404 error and when encountered trying to "install updates", which really occurs when trying to
download the update files so that the updates can be installed, is almost always a function of the desired file having been manually deleted from the WSUS server. The file that should be there for the needed update, isn't, but it used to be.
If all of the clients are getting this error on all updates, then that's a function of the content store on the WSUS server being missing, in the wrong place, or configured with the wrong ACLs.
After running the WSUS Client Diagnostic Tool I get the result : GetFileVersion(szEngineDir,&susVersion) failed with hr=0x80070002
This result is inconclusive, and not really relevant. The CDT is 32-bit only and can't be used on 64-bit systems. Plus, we already know the client is talking to the WSUS server -- you've reported the error code -- so the Client Diagnostic Tool will
tell us nothing of use at this point (even if it did work on 64-bit systems).
On a Windows 2003 server the WSUS Client Diagnostic Tool shows no error message.
Cool. It works on a 32-bit system.
So I guess the problem seems to be specificly related to Windows 2008 servers.
No... BUT... allow me to make an example of this for just a moment, and forgive me for that.
This is a great example of arriving at the wrong conclusion, caused by not considering ALL of the differences, as well as the scope and capability of the diagnostics performed. The error is not because one is '2003' and the other '2008; the error is because
one is 'x86' and the other is (obviously) 'x64'. And, in either case, diagnosing the client was wasted effort because the client is already working. (It got a real HTTP error message from the WSUS server.)
Now, we need to get some real diagnostic information to find out why you're getting this error code. :-)
Please post the actual entries from the WindowsUpdate.log where this error code appears, plus a hundred lines prior, and let's get some context around the error code, and the exact update that's involved in this issue.
Lawrence Garvin, M.S., MCSA, MCITP:EA, MCDBA
SolarWinds Head Geek
Microsoft MVP - Software Packaging, Deployment & Servicing (2005-2014)
My MVP Profile: http://mvp.microsoft.com/en-us/mvp/Lawrence%20R%20Garvin-32101
http://www.solarwinds.com/gotmicrosoft
The views expressed on this post are mine and do not necessarily reflect the views of SolarWinds.

Error code 80244017 WSUS windows 2008 server.

Hi Team,
this is inform you to that, All the windows 7 client PC Computers or getting update from WSUS but windows 2008 servers or not geting the update,
its througing the error message.
Error code:80244017
All server and client computers or same WSUS Server.
Regards, Kumar.V

Could you please help me any one on this issue .........?
Not any more than I already have....
You should look in the IIS logs for the WSUS v-root and determine exactly which type of HTTP 401 error this is.
If you don't understand about Internet Information Services (IIS), there are thousands of available resources -- and understanding how to use, administer, and manage IIS is a core skill required to
manage a WSUS server. I would start at http://www.iis.net.
Talking with the person who actually installed IIS on the WSUS server is also a good idea, including ensuring that it was configured as documented in the WSUS Deployment Guide:
Configure Internet Information Services
Lawrence Garvin, M.S., MCITP:EA, MCDBA, MCSA
Product Manager, SolarWinds
Microsoft MVP - Software Distribution (2005-2012)
My MVP Profile: http://mvp.support.microsoft.com/profile/Lawrence.Garvin

Windows 2008 R2 Port Issue

Dear Tech Gurus,
Please see that we have Windows 2008 R2 Enterprise Edition on which we run our application which uses TCP Port 49158.
Yesterday our application stopped accidentally and when we tried to start application again it refuses.
I have telnet 127.0.0.1 49158 and it shows the same server get this port.
I change the port to 48157 and again try to run the server and it started successfully.
Today same issue happened. And now the 48157 is not working same behavior and I change the port to 49158 and it works fine.
What will be the possible reason please help.
Thanks
Malik Adeel Imtiaz
Malik Adeel Imtiaz

Dear Techno Trev,
Thank you so much for your reply very much appreciated.
Can you please elaborate me that how I can reserve my (49158) port in Windows 2008 R2 as you said in your reply.
Thanks
Adeel Imtiaz
Malik Adeel Imtiaz

Windows 2012 WSUS Downsteam server to Windows 2008 WSUS server

Hi
we have installed windows 2008 Upstream server to Windows 2012 WSUS server and now they are able to sync the updates and but some updates are not able to download so what could be the issue.
whether this design is supported please confirm.

we have installed windows 2008 Upstream server to Windows 2012 WSUS server and now they are able to sync the updates and but some updates are not able to download so what could be the issue.
Have you installed KB2734608 on the upstream server?
whether this design is supported please confirm.
It is *NOT* supported.. but it *WILL* work if KB2734608 is installed on the WSUS v3 server.
Lawrence Garvin, M.S., MCSA, MCITP:EA, MCDBA
SolarWinds Head Geek
Microsoft MVP - Software Packaging, Deployment & Servicing (2005-2014)
My MVP Profile: http://mvp.microsoft.com/en-us/mvp/Lawrence%20R%20Garvin-32101
http://www.solarwinds.com/gotmicrosoft
The views expressed on this post are mine and do not necessarily reflect the views of SolarWinds.

Update Windows Root Certificates in Windows 2008 R2 Disconnected Environment using WSUS

Hi all, I need to update the root certs on all my WIndows 2008 R2 servers. They have no internet connectvity. I am aware of the issue described by
KB931125 but I am not affected by it. My issue is that I would like the 2008R2 servers to update the roots certs form my WSUS servers. Is this possible?

I would suggest that you identify the few individual root certificates that you need, and import them individually to those servers where they are needed.
It is NOT possible to update root certificates from a WSUS server, except in the case of workstations that are being configured to install KB931125.
Do NOT install KB931125 to a server operating system.
Lawrence Garvin, M.S., MCSA, MCITP:EA, MCDBA
SolarWinds Head Geek
Microsoft MVP - Software Packaging, Deployment & Servicing (2005-2014)
My MVP Profile: http://mvp.microsoft.com/en-us/mvp/Lawrence%20R%20Garvin-32101
http://www.solarwinds.com/gotmicrosoft
The views expressed on this post are mine and do not necessarily reflect the views of SolarWinds.

Content Transfer between WSUS and SCCM client on port 8530

Dear All
In my environment from last few days we are facing an strange situtaion where huge contents is getting transferred between WSUS server and SCCM client on port 8530.
I check logs on client and found that client are getting contents from their associated DP's but still weekly network utlisation report showing that data in GB's was transferred between SCCM primary server and clients on port 8530.
Kindly suggest what else need to check in this scenario
Regards Suresh

The only other possible traffic from WSUS is actual updates if and only if you have been approving updates directly in WSUS which you should not be doing.
Thus, assuming you are not doing what you should not be doing, the only possibility is the update catalog. 150-200MB sounds excessive but that will be based upon what you all have selected for your catalog. There are also a handful of reasons why a full
catalog resync would be initiated instead of just a delta.
Jason | http://blog.configmgrftw.com

In Place Upgrade WSUS windows 2008 R2 into windows server 2012

Hi Team,
i had question. I have windows server 2008 R2 and installed WSUS role at that server.
Can I do inplace upgrade into windows server 2012 std edition?
is there any impact into wsus services?
thanks

If it is not a DC, upgrade should be easy. And there shouldn’t be any problems.
The question was about upgrading a WSUS server, and regardless of whether it's a DC or not, it most emphatically will not be problem free. In fact, it's flat out not possible! On WS2012 the upgrade will be blocked if WSUS v3 is present,
and on WS2012R2 it will corrupt the WSUS installation beyond repair requiring a reinstallation of the operating system.
Please review the
WSUS v6 documentation regarding upgrade requirements.
Warning
Upgrade from any version of Windows Server that supports WSUS 3.2 to Windows Server® 2012 R2 requires that you first uninstall WSUS 3.2.
In Windows Server 2012, upgrading from any version of Windows Server with WSUS 3.2 installed is blocked during the installation process if WSUS 3.2 is detected, and you are prompted to first uninstall Windows Server Update Services prior to upgrading Windows
Server 2012.
However, because of changes in Windows Server 2012 R2, when upgrading from any version of Windows Server and WSUS 3.2 to Windows Server 2012 R2, the installation is not blocked. Failure to uninstall WSUS 3.2 prior to performing a Windows Server 2012 R2 upgrade
will cause the post installation tasks for WSUS in Windows Server 2012 R2 to fail. In this case, the only known corrective measure is to format the hard drive and reinstall Windows Server 2012 R2.
Lawrence Garvin, M.S., MCSA, MCITP:EA, MCDBA
SolarWinds Head Geek
Microsoft MVP - Software Packaging, Deployment & Servicing (2005-2014)
My MVP Profile: http://mvp.microsoft.com/en-us/mvp/Lawrence%20R%20Garvin-32101
http://www.solarwinds.com/gotmicrosoft
The views expressed on this post are mine and do not necessarily reflect the views of SolarWinds.

Windows 2008 FRS port Customization causing Replication Delay

Hi
we have 4 windows 2008 R2 DC. we have restricted the port for FRS Replication. now we are facing replication delay.
Not finding any error in DCDIAG, REPADMIN /Showreps and in FRS event there is an error 13508 and it is not recovering since from 3 days to 13509 so please suggest the solution
whether Port customizion is recommended

Hi,
We can restrict FRS replication traffic to a specific static port. However, if there is an intermediate network device or software that is being used to filter packets between domain controllers, we need to verify that the device or the software
allows communication over the specified port. Additionally, make sure the destination TCP port that we set is open on the firewall.
Regarding restricting FRS replication traffic to a specific static port, the following article can be referred to for more information.
How to restrict FRS replication traffic to a specific static port
https://support.microsoft.com/en-us/kb/319553
Regarding troubleshooting FRS Event ID 13508, the following article can be referred to for more information.
Troubleshooting File Replication Service
https://msdn.microsoft.com/en-us/library/bb727056.aspx#EMAA
Best regards,
Frank Shen
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

CRM 7.0 installation failed on Windows 2008 R2 SQL Server 2008 SP1

Hello I'm currently trying to install CRM 7.0 on a windows 2008 R2 (64B) plateform with SQL Server 2008 SP1 as database engine
while launching sapinst.exe i'm facing this issue that i cannot get rid of it
Could someone Help , would really be appreciated as i'm a newby on SAP world
thanks a lot
Unable to start a service execution. Please check the following information for the possibble reason and inform the installation development : Opened sylib701_1.dll exe dir is C:/Users/SAPINS1/AppData/Local/Temp/2/sapinst_exe.3492.1286357336 Opened C:/Users/SAPINS1/AppData/Local/Temp/2/sapinst_exe.3492.1286357336/iaguieng701_1.dll receiving and sending on port 21200 Environment variable SAPINST_JRE_HOME set to value 'C:/Users/SAPINS1/AppData/Local/Temp/2/sapinst_exe.3492.1286357336/jre'. exe dir is C:/Users/SAPINS1/AppData/Local/Temp/2/sapinst_exe.3492.1286357336 Creating file C:\Program Files\sapinst_instdir\x. Removing file C:\Program Files\sapinst_instdir\x. Opened C:/Users/SAPINS~1/AppData/Local/Temp/2/sapinst_exe.3492.1286357336/iakdblib701_1.dll This is SAPinst, version 701_1, make variant 701_REL, build 1015514 compiled on Oct 3 2008, 01:51:15 MessageLib initialized successfully. showing dlg diProductChoice <dialog sid="diProductChoice"> <title>Welcome to SAP Installation Master</title> <dialog/> Login in progress Connection request to guiengine backend by host 169.254.138.68 Protocol version is 3.1 Send connect information client logged on Waiting for an answer from GUI CDialogHandler: ACTION_NEXT requested <dialog sid="diProductChoice"> <dialog/> Creating file C:\Windows\System32\x. Removing file C:\Windows\System32\x. showing dlg diRestartOrCancel <dialog sid="diRestartOrCancel"> Dialog does not contain standard input handler, so the backend is not able to generate a log entry <dialog/> Waiting for an answer from GUI current working directory is C:/Windows/System32 Creating file C:\Program Files\sapinst_instdir\x. Removing file C:\Program Files\sapinst_instdir\x. Unable to open URL file://C:\Windows\System32\control.xml. The execution will be terminated now.

Hi!
Windows 2008 R2 is not yet listed in the PAM - and hence not yet supported. The technical prerequisites are met (with a special kernel patch) but not all software is released, so you may get it to run technically but not everything is tested and so, you should not install any SAP system on it!
In fact, and just to provide you further details it is not possible to expect the 710 products released for Windows Server 2008 R2 before around four weeks; 700 products will be released even after 710.
See [SAP note 1383873|https://service.sap.com/sap/support/notes/1383873] ("Windows Server 2008 R2 Support").
You can be always up to date with the latest Windows news at:
[SAP on Microsoft Windows|SAP on Microsoft Windows] --> Support of Microsoft Windows Server 2008 R2
Cheers!

11g GC Installation Problem on Windows 2008

Hi All
I am facing a problem installing 11GC on Windows 2008. The installer will not get past "Step 12 - Agent Configuration Assistant" - it shows as FAILED.
My setup is as following:
- GCSERVER: where I am installing GC - Windows 2008 R1 32-bit (Actually a VMware VM)
- DBSERVER: where em repository db resides - Windows 2008 R1 64-bit (Physical Server)
The steps I have followed:
- Created a new database called emrep111 (11.1.0.7) on DBSERVER
- Installed WL Server (10.3.2) on GCSERVER
- Run GC 11.1.0.1.0 for Win32 on GCSERVER and then get error
I have to cancel the installation at this stage, however, I would have expected by the time it gets to this stage it would have done the important stuff, however, when I browse to the EM URL I get "Backend WLS or EM application seems to be down".
If anyone has any experience of 11g GC on Windows I would be grateful if you have any advice on Troubleshooting this problem.
Regards
Alan

Hi All,
a short intermediate result:
Oracle Support is working on the problem. Today they asked me to perform the following action:
set EM_SECURE_VERBOSE=true
+<agent_home>\bin>emctl secure agent+
If you take a look at the generated log file '<agent_home>\sysman\log\secure.log' you can see that OMS does not respond correctly:
[27-07-2010 10:06:50] USERINFO ::Securing agent... Started.
[27-07-2010 10:06:50] DEBUG ::Executing ... D:\oracle\product\em\agent11g\jdk\jre/bin/java -cp D:/oracle/product/em/agent11g/jdbc/lib/ojdbc5.jar;D:/oracle/product/em/agent11g/lib/xmlparserv2.jar;D:\oracle\product\em\agent11g/sysman/jlib/log4j-core.jar;D:/oracle/product/em/agent11g/jlib/share.jar;D:/oracle/product/em/agent11g/jlib/http_client.jar;D:/oracle/product/em/agent11g/jlib/jssl-1_1.jar;D:/oracle/product/em/agent11g/jlib/ojmisc.jar;D:/oracle/product/em/agent11g/opmn/lib/optic.jar;D:\oracle\product\em\agent11g/sysman/jlib/emagentRT.jar;D:\oracle\product\em\agent11g/sysman/jlib/emagentSDK.jar;D:/oracle/product/em/agent11g/lib/dms.jar;D:/oracle/product/em/agent11g/lib/dmsEmd.jar;D:\oracle\product\em\agent11g/sysman/jlib/emcoreAgent.jar;D:/oracle/product/em/agent11g/modules/oracle.http_client_11.1.1.jar -DEMSTATE=D:\oracle\product\em\agent11g -Ddebug=true oracle.sysman.emctl.secure.agent.SecureAgentCmd
2010-07-27 10:06:56,352 [main] INFO agent.SecureAgentCmd secureAgent.226 - Requesting an HTTPS Upload URL from the OMS
2010-07-27 10:06:56,368 [main] INFO agent.SecureAgentCmd openPage.829 - Opening: https://BTNDBSRV4.btnntdom.local:1159/em/genwallet
2010-07-27 10:07:15,166 [main] INFO agent.SecureAgentCmd openPage.855 - Response Status Code: 200
2010-07-27 10:07:15,166 [main] INFO agent.SecureAgentCmd openPage.863 - RESPONSE_STATUS header: null
2010-07-27 10:07:15,166 [main] INFO agent.SecureAgentCmd openPage.864 - Response body: <head><title>OMS is unavailable</title></head><body><br><br><div align=center><b><font size=5>Backend WLS or EM application seems to be down</font></b></div></body>
2010-07-27 10:07:15,166 [main] INFO agent.SecureAgentCmd getOMSSecurePort.809 - Non-numeric response obtained: <head><title>OMS is unavailable</title></head><body><br><br><div align=center><b><font size=5>Backend WLS or EM application seems to be down</font></b></div></body>
2010-07-27 10:07:15,166 [main] INFO agent.SecureAgentCmd getOMSSecurePort.811 - OMS Secure Port: -1
2010-07-27 10:07:15,166 [main] ERROR agent.SecureAgentCmd secureAgent.231 - The OMS is not set up for Enterprise Manager Security.
2010-07-27 10:07:15,166 [main] ERROR agent.SecureAgentCmd main.210 - Failed to secure the Agent:
java.lang.Exception: The OMS is not set up for Enterprise Manager Security.
at oracle.sysman.emctl.secure.agent.SecureAgentCmd.secureAgent(SecureAgentCmd.java:232)
at oracle.sysman.emctl.secure.agent.SecureAgentCmd.main(SecureAgentCmd.java:203)
I'm curious about the next steps from Oracle Support.
Best rgds
Kai

EPM 11.1.2: Foundation Services config fails on Windows 2008 SP1 server.

Hi,
I installed EPM 11.1.2 on Windows 2008 SP1, 32-bit. The installation succeeded (no errors in logs). However, when I run EPM Configurator to configure Foundation Services, it fails.
Environment:
EPM Server: Windows 2008 SP1 32-bit
RDBMS: Oracle Enterprise Edition 10.2.0.4 (running on remote AIX 5.3 TL 8 server)
Oracle Client: 10.2.0.4 (full client install)
The configtool.log (see below) indicates that the program cannot find the reg.properties file. I checked the server and this file does not exist. The log file also reports non-existing classpath entries (not sure if this is related). The registry.log file (see below) reports a jdbc driver error: java.sql.SQLSyntaxErrorException: ORA-00917: missing comma.
I submitted a service request with Oracle Support, but the support engineer said that installation and configuration errors are outside the scope of technical support.
Any ideas/suggestions would be greatly appreciated.
Thank you.
Configtool_Summary.log:
---- Product Configuration Summary.....
( May 9, 2010 6:55:58 AM ): ---- Hyperion Foundation Configuration......
( May 9, 2010 6:55:59 AM ): Pre-Configuration :: pass
( May 9, 2010 6:55:59 AM ): Common Settings :: fail
( May 9, 2010 6:56:03 AM ): Configure Database :: pass
( May 9, 2010 6:56:03 AM ): Deploy to Application Server :: fail
( May 9, 2010 6:57:03 AM ): Configure Oracle Configuration Manager :: fail
( May 9, 2010 6:57:08 AM ): ---- Workspace Configuration......
( May 9, 2010 6:57:08 AM ): Deploy to Application Server :: fail
Configtool.log:
[2010-05-09T06:49:19.927-06:00] [EPMCFG] [TRACE] [EPMCFG-01001] [oracle.EPMCFG] [tid: 10] [ecid: 0000IXx7D4337E65zNd9iW1BtexF000000,0] [SRC_CLASS: com.oracle.preconfig.util.EpmLoggerPreConfigReporter] trace: Running preconfig checks...[[
Running EPM_ORACLE_HOME check...
EPM_ORACLE_HOME environment variable value: C:\Oracle\Middleware\EPMSystem11R1
JAVA_HOME environment variable value: C:\Oracle\Middleware\EPMSystem11R1\..\jdk160_11
EPM_ORACLE_HOME check succeeded
Running .oracle.products check... .oracle.products check succeeded
Running Jars manifest check...
Time spent for manifests parsing: 55129 ms
Maximum jars depth achieved: 9, while restriction was: unrestricted
Parsed 439 manifests
Total jars and classpath entries encountered: 439
Total not-existing referenced classpath entries count: 28
Enumerating not-existing classpath entries:
Missing (depth 9) file C:\oracle\Middleware\modules\com.bea.cie.comdev.it_6.1.1.0.jar referenced from C:\oracle\Middleware\modules\features\com.bea.cie.config.it_6.1.0.0.jar referenced from C:\oracle\Middleware\modules\features\com.bea.cie.config.L10N_6.1.0.0.jar referenced from C:\oracle\Middleware\modules\features\com.bea.cie.config_6.1.0.0.jar referenced from C:\oracle\Middleware\utils\config\10.3\config-launch.jar referenced from C:\oracle\Middleware\wlserver_10.3\common\lib\pdev.jar referenced from C:\oracle\Middleware\wlserver_10.3\server\lib\weblogic.jar referenced from C:\oracle\Middleware\EPMSystem11R1\common\jlib\11.1.2.0\epm_jrf.jar referenced from C:\oracle\Middleware\EPMSystem11R1\common\jlib\11.1.2.0\epm_j2se.jar referenced from C:\oracle\Middleware\EPMSystem11R1\common\config\11.1.2.0\configtool.jar
Missing (depth 5) file C:\oracle\Middleware\wlserver_10.3\server\lib\wlw-langx-L10N.jar referenced from C:\oracle\Middleware\wlserver_10.3\server\lib\wlw-langx.jar referenced from C:\oracle\Middleware\wlserver_10.3\server\lib\weblogic.jar referenced from C:\oracle\Middleware\EPMSystem11R1\common\jlib\11.1.2.0\epm_jrf.jar referenced from C:\oracle\Middleware\EPMSystem11R1\common\jlib\11.1.2.0\epm_j2se.jar referenced from C:\oracle\Middleware\EPMSystem11R1\common\config\11.1.2.0\configtool.jar
Total classpath elements to check: 67
Check for C:\oracle\Middleware\EPMSystem11R1\common\config\11.1.2.0\lib\hit-common.jar existence succeeded; file depth: 1
Check for C:\oracle\Middleware\EPMSystem11R1\common\config\11.1.2.0\lib\hit-config.jar existence succeeded; file depth: 1
Jars manifest check succeeded
Running Environment variables check... Environment variables check succeeded
Running Windows system32 directory check... Windows system32 directory check succeeded
Preconfig checks passed! Going further
[2010-05-09T06:49:22.303-06:00] [EPMCFG] [NOTIFICATION] [EPMCFG-01731] [oracle.EPMCFG] [tid: 10] [ecid: 0000IXx7D4337E65zNd9iW1BtexF000000,0] [SRC_CLASS: com.hyperion.config.wizard.ConfigToolWizardLoader] Couldnt find proper class for wizard state: {0}, skipping...
[2010-05-09T06:49:22.943-06:00] [EPMCFG] [WARNING] [EPMCFG-01001] [oracle.EPMCFG] [tid: 10] [ecid: 0000IXx7D4337E65zNd9iW1BtexF000000,0] [SRC_CLASS: com.hyperion.config.document.Storage] trace: {0}[[
com.hyperion.hit.registry.exceptions.RegistryException: No database properties could be read
[2010-05-09T06:49:22.943-06:00] [EPMCFG] [TRACE] [EPMCFG-05934] [oracle.EPMCFG] [tid: 10] [ecid: 0000IXx7D4337E65zNd9iW1BtexF000000,0] [SRC_CLASS: com.hyperion.cis.utils.StopWatch] Task [Init Storage] has been started.
[2010-05-09T06:49:22.943-06:00] [EPMCFG] [TRACE] [EPMCFG-05934] [oracle.EPMCFG] [tid: 10] [ecid: 0000IXx7D4337E65zNd9iW1BtexF000000,0] [SRC_CLASS: com.hyperion.cis.utils.StopWatch] Task [Getting registry instance] has been started.
[2010-05-09T06:49:22.943-06:00] [EPMCFG] [WARNING] [EPMCFG-01001] [oracle.EPMCFG] [tid: 10] [ecid: 0000IXx7D4337E65zNd9iW1BtexF000000,0] [SRC_CLASS: com.hyperion.config.document.Storage] trace: com.hyperion.hit.registry.exceptions.RegistryException: No database properties could be read
[2010-05-09T06:49:22.943-06:00] [EPMCFG] [TRACE] [EPMCFG-05935] [oracle.EPMCFG] [tid: 10] [ecid: 0000IXx7D4337E65zNd9iW1BtexF000000,0] [SRC_CLASS: com.hyperion.cis.utils.StopWatch] Task [Getting registry instance] has been ended. Execution time [0] sec.
[2010-05-09T06:49:22.943-06:00] [EPMCFG] [TRACE] [EPMCFG-05934] [oracle.EPMCFG] [tid: 10] [ecid: 0000IXx7D4337E65zNd9iW1BtexF000000,0] [SRC_CLASS: com.hyperion.cis.utils.StopWatch] Task [Loading CT documents] has been started.
[2010-05-09T06:49:22.959-06:00] [EPMCFG] [NOTIFICATION] [EPMCFG-01044] [oracle.EPMCFG] [tid: 10] [ecid: 0000IXx7D4337E65zNd9iW1BtexF000000,0] [SRC_CLASS: com.hyperion.cis.config.document.ConfigToolDocumentManager] Loading product descriptor from file C:\Oracle\Middleware\EPMSystem11R1\common\config\11.1.2.0\product\aps\11.1.2.0\default_aps_1.xml...
[2010-05-09T06:50:53.137-06:00] [EPMCFG] [TRACE] [EPMCFG-05922] [oracle.EPMCFG] [tid: 13] [ecid: 0000IXx7Zkm37E65zNd9iW1BtexF000004,0] [SRC_CLASS: com.hyperion.install.sw.SoftwareRegistry] Adding Hyperion Home entry...
[2010-05-09T06:50:53.137-06:00] [EPMINS] [NOTIFICATION] [EPMINS-00006] [oracle.EPMINS] [tid: 13] [ecid: 0000IXx7Zkm37E65zNd9iW1BtexF000004,0] [SRC_CLASS: com.hyperion.hit.wizard.Wizard] Wizard state is: RegistryWizardState
[2010-05-09T06:51:41.437-06:00] [EPMINS] [TRACE] [EPMINS-00015] [oracle.EPMINS] [tid: 11] [ecid: 0000IXx7Zhb37E65zNd9iW1BtexF000002,0] [SRC_CLASS: com.hyperion.hit.wizard.AbstractWizardAction] Invoked action: navigation.next
[2010-05-09T06:51:41.453-06:00] [EPMCFG] [ERROR] [EPMCFG-01001] [oracle.EPMCFG] [tid: 14] [ecid: 0000IXx7j^D37E65zNd9iW1BtexF000005,0] [SRC_CLASS: com.hyperion.config.document.Storage] trace: {0}[[
com.hyperion.hit.registry.exceptions.RegistryException: com.hyperion.hit.registry.exceptions.RegistryException: No database properties could be read
     at com.hyperion.hit.registry.Registry.releaseInstance(Registry.java:2039)
     at com.hyperion.config.document.Storage.resetRegistryItems(Storage.java:811)
     at com.hyperion.config.document.Storage.resetRegistry(Storage.java:798)
     at com.hyperion.config.wizard.impl.RegistryWizardState$1.validate(RegistryWizardState.java:348)
     at com.hyperion.hit.wizard.Wizard$NextClass.run(Wizard.java:504)
     at java.lang.Thread.run(Thread.java:619)
Caused by: com.hyperion.hit.registry.exceptions.RegistryException: No database properties could be read
     at com.hyperion.hit.registry.datasource.SharedServicesDataSourceFactory.getDataSource(SharedServicesDataSourceFactory.java:29)
     at com.hyperion.hit.registry.datasource.SharedServicesDatabaseConnectionBuilder.getConnection(SharedServicesDatabaseConnectionBuilder.java:26)
     at com.hyperion.hit.registry.RegistryUtils.createNewConnection(RegistryUtils.java:183)
     at com.hyperion.hit.registry.RegistryConnection.getInstance(RegistryConnection.java:149)
     at com.hyperion.hit.registry.Registry.releaseInstance(Registry.java:2030)
     ... 5 more
[2010-05-09T06:51:46.891-06:00] [EPMCFG] [WARNING] [EPMCFG-01863] [oracle.EPMCFG] [tid: 14] [ecid: 0000IXx7j^D37E65zNd9iW1BtexF000005,0] [SRC_CLASS: com.hyperion.config.wizard.impl.RegistryWizardState] Unknown server type: ORACLE
[2010-05-09T06:51:46.938-06:00] [EPMCFG] [TRACE] [EPMCFG-01864] [oracle.EPMCFG] [tid: 14] [ecid: 0000IXx7j^D37E65zNd9iW1BtexF000005,0] [SRC_CLASS: com.hyperion.config.wizard.impl.RegistryWizardState] HSS DB commit: serverType = ORACLE, host = fsdev21.jeffco.k12.co.us, port = 1521, db = EPMDMO
[2010-05-09T06:54:20.402-06:00] [EPMCFG] [TRACE] [EPMCFG-01001] [oracle.EPMCFG] [tid: 22] [ecid: 0000IXx8MHf37E65zNd9iW1BtexF00000B,0] [SRC_CLASS: com.hyperion.cis.utils.Log4jEPMLoggerAdapter] trace: oracle.sysman.ccr.common.network.EndPoint: SSL Protocol Initialized - SSL SocketFactory initialized
[2010-05-09T06:54:20.699-06:00] [EPMCFG] [TRACE] [EPMCFG-01001] [oracle.EPMCFG] [tid: 22] [ecid: 0000IXx8MHf37E65zNd9iW1BtexF00000B,0] [SRC_CLASS: com.hyperion.cis.utils.Log4jEPMLoggerAdapter] trace: oracle.sysman.ccr.common.network.EndPoint: Peer Certificate Chain(3):
[2010-05-09T06:54:20.714-06:00] [EPMCFG] [TRACE] [EPMCFG-01001] [oracle.EPMCFG] [tid: 22] [ecid: 0000IXx8MHf37E65zNd9iW1BtexF00000B,0] [SRC_CLASS: com.hyperion.cis.utils.Log4jEPMLoggerAdapter] trace: oracle.sysman.ccr.common.network.EndPoint: [[[
Version: V3
Subject: CN=ccr.oracle.com, OU=Terms of use at www.verisign.com/rpa (c)05, OU=Global IT, O=Oracle Corporation, L=Redwood Shores, ST=California, C=US
Signature Algorithm: SHA1withRSA, OID = 1.2.840.113549.1.1.5
Key: Sun RSA public key, 1024 bits
modulus: 126484617735060833031672477175673947636995798346030414463203905767325249772953279144384357766006815101034501698878511926718137275402247180206176507598520965207099036209959054153609440070358274987559344845438007585125964758282852498389487164896685302381484205088204064664382056656592869143856352689583929480807
public exponent: 65537
Validity: [From: Mon May 04 18:00:00 MDT 2009,
               To: Sun Jul 04 17:59:59 MDT 2010]
Issuer: CN=VeriSign Class 3 Secure Server CA, OU=Terms of use at https://www.verisign.com/rpa (c)05, OU=VeriSign Trust Network, O="VeriSign, Inc.", C=US
SerialNumber: [    52b9bccd 239d7a0d 7bb16003 389848b0]
Certificate Extensions: 8
[1]: ObjectId: 1.3.6.1.5.5.7.1.12 Criticality=false
Extension unknown: DER encoded OCTET string =
0000: 04 62 30 60 A1 5E A0 5C 30 5A 30 58 30 56 16 09 .b0`.^.\0Z0X0V..
0010: 69 6D 61 67 65 2F 67 69 66 30 21 30 1F 30 07 06 image/gif0!0.0..
0020: 05 2B 0E 03 02 1A 04 14 4B 6B B9 28 96 06 0C BB .+......Kk.(....
0030: D0 52 38 9B 29 AC 4B 07 8B 21 05 18 30 26 16 24 .R8.).K..!..0&.$
0040: 68 74 74 70 3A 2F 2F 6C 6F 67 6F 2E 76 65 72 69 http://logo.veri
0050: 73 69 67 6E 2E 63 6F 6D 2F 76 73 6C 6F 67 6F 31 sign.com/vslogo1
0060: 2E 67 69 66 .gif
[2]: ObjectId: 2.5.29.35 Criticality=false
AuthorityKeyIdentifier [
KeyIdentifier [
0000: 6F EC AF A0 DD 8A A4 EF F5 2A 10 67 2D 3F 55 82 o........*.g-?U.
0010: BC D7 EF 25 ...%
[3]: ObjectId: 2.5.29.31 Criticality=false
CRLDistributionPoints [
[DistributionPoint:
[URIName: http://SVRSecure-crl.verisign.com/SVRSecure2005.crl]
[4]: ObjectId: 2.5.29.37 Criticality=false
ExtendedKeyUsages [
serverAuth
clientAuth
[5]: ObjectId: 2.5.29.32 Criticality=false
CertificatePolicies [
[CertificatePolicyId: [2.16.840.1.113733.1.7.23.3]
[PolicyQualifierInfo: [
qualifierID: 1.3.6.1.5.5.7.2.1
qualifier: 0000: 16 1C 68 74 74 70 73 3A   2F 2F 77 77 77 2E 76 65 ..https://www.ve
0010: 72 69 73 69 67 6E 2E 63   6F 6D 2F 72 70 61        risign.com/rpa
[6]: ObjectId: 2.5.29.15 Criticality=false
KeyUsage [
DigitalSignature
Key_Encipherment
[7]: ObjectId: 1.3.6.1.5.5.7.1.1 Criticality=false
AuthorityInfoAccess [
[accessMethod: 1.3.6.1.5.5.7.48.1
   accessLocation: URIName: http://ocsp.verisign.com, accessMethod: 1.3.6.1.5.5.7.48.2
   accessLocation: URIName: http://SVRSecure-aia.verisign.com/SVRSecure2005-aia.cer]
[8]: ObjectId: 2.5.29.19 Criticality=false
BasicConstraints:[
CA:false
PathLen: undefined
Algorithm: [SHA1withRSA]
[2010-05-09T06:54:20.714-06:00] [EPMCFG] [TRACE] [EPMCFG-01001] [oracle.EPMCFG] [tid: 22] [ecid: 0000IXx8MHf37E65zNd9iW1BtexF00000B,0] [SRC_CLASS: com.hyperion.cis.utils.Log4jEPMLoggerAdapter] trace: oracle.sysman.ccr.common.network.EndPoint: [[[
Version: V3
Subject: CN=VeriSign Class 3 Secure Server CA, OU=Terms of use at https://www.verisign.com/rpa (c)05, OU=VeriSign Trust Network, O="VeriSign, Inc.", C=US
Signature Algorithm: SHA1withRSA, OID = 1.2.840.113549.1.1.5
Key: Sun RSA public key, 2048 bits
modulus: 18905729229464742433949840178165285210788629616064305164260843170201977241822595607598003983710482114887504542420063531704226365322091550579034120400511694538047325464426047959412241672706076731441028369861556999479337863789783838582999151810376013650218058341794419022809268802993425241541430009002110553726612125414429934927217253337526656605550620555845061032537869588361121949241772361851996536275260212221084778605793422355009443918198903890623415507477268041766919150091887619618794603091993360637671933766441597921249204891707900552776893415739395596650548462810104696585021566385762017523199762687187467514321
public exponent: 65537
Validity: [From: Tue Jan 18 17:00:00 MST 2005,
               To: Sun Jan 18 16:59:59 MST 2015]
Issuer: OU=Class 3 Public Primary Certification Authority, O="VeriSign, Inc.", C=US
SerialNumber: [    75337d9a b0e1233b ae2d7de4 469162d4]
<RESPONSE><STATUS CODE="202"><MESSAGE></MESSAGE></STATUS><REQUEST_DATA><REGISTRATION_CIPHER VALUE="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"/></REQUEST_DATA></RESPONSE>
[2010-05-09T06:55:22.359-06:00] [EPMCFG] [WARNING] [EPMCFG-01001] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.hit.fusion.FusionComponent] trace: The component type 'Foundation' is not supported. Valid component types are: [OCM, OHS, WebCache]
[2010-05-09T06:55:33.954-06:00] [EPMCFG] [ERROR] [EPMCFG-01001] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.config.document.Storage] trace: com.hyperion.hit.registry.exceptions.RegistryException: Unable to create registry.
[2010-05-09T06:55:33.954-06:00] [EPMCFG] [TRACE] [EPMCFG-02015] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.config.wizard.impl.RunAllTasks] Creating product component(s) in the HIT Registry (if not created yet) for all selected product(s)...
[2010-05-09T06:55:33.954-06:00] [EPMCFG] [TRACE] [EPMCFG-01321] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.cis.config.ConfigRegistryUtils] Creating product component: component type = SHARED_SERVICES_PRODUCT
[2010-05-09T06:55:33.954-06:00] [EPMCFG] [TRACE] [EPMCFG-01322] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.cis.config.ConfigRegistryUtils] Product component already exists in the registry: component type = SHARED_SERVICES_PRODUCT
[2010-05-09T06:55:33.954-06:00] [EPMCFG] [TRACE] [EPMCFG-01321] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.cis.config.ConfigRegistryUtils] Creating product component: component type = WORKSPACE
[2010-05-09T06:55:42.970-06:00] [EPMCFG] [TRACE] [EPMCFG-05955] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.config.document.Storage] Setting link. Parent: id [b57bd794d9cd2537337158c31287d1efc497ffe], componnet type [FOUNDATION_SERVICES_PRODUCT]. Child: id [b57bd794d9cd2537337158c31287d1efc497ff1], component type [WORKSPACE]
[2010-05-09T06:55:42.970-06:00] [EPMCFG] [TRACE] [EPMCFG-02144] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.config.document.Storage] Storage storeComponent trace : WORKSPACE:[b57bd794d9cd2537337158c31287d1efc497ff1] to be stored
[2010-05-09T06:55:42.970-06:00] [EPMCFG] [TRACE] [EPMCFG-02144] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.config.document.Storage] Storage storeComponent trace : allRegistryComponents contains WORKSPACE:[b57bd794d9cd2537337158c31287d1efc497ff1]
[2010-05-09T06:55:42.970-06:00] [EPMCFG] [TRACE] [EPMCFG-02144] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.config.document.Storage] Storage storeComponent trace : toUpdateComponents did not contain WORKSPACE:[b57bd794d9cd2537337158c31287d1efc497ff1]. It has been added to toUpdateComponents
[2010-05-09T06:55:42.970-06:00] [EPMCFG] [TRACE] [EPMCFG-01426] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.cis.ant.AbstractAntConfigurator] propertiesExtractLocation : C:\Oracle\Middleware\user_projects\domains\EPMSystem\scripts
[2010-05-09T06:55:47.986-06:00] [EPMCFG] [ERROR] [EPMCFG-01001] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.cis.utils.Shortcut] trace: shortcut out:Microsoft (R) Windows Script Host Version 5.7[[
Copyright (C) Microsoft Corporation. All rights reserved.
[2010-05-09T06:55:58.627-06:00] [EPMCFG] [ERROR] [EPMCFG-02151] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.hit.fusion.FusionComponent] oracleComponent is null. Component will not be provisioned.
[2010-05-09T06:56:02.690-06:00] [EPMCFG] [WARNING] [EPMCFG-01113] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.cis.config.AbstractProductDBConfigurator] Couldn't find product component in updateRegistryEntries
[2010-05-09T06:56:02.706-06:00] [EPMCFG] [NOTIFICATION] [EPMCFG-01107] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.cis.DBConfigurator] Running file: C:\Oracle\Middleware\EPMSystem11R1\products\Foundation\workspace\database\Oracle\create.sql
[2010-05-09T06:56:03.503-06:00] [EPMCFG] [ERROR] [EPMCFG-01020] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.config.wizard.impl.RunAllTasks] Error: [[
java.lang.NullPointerException
     at com.hyperion.cis.config.AppServerDeployer.isDeployAsWinService(AppServerDeployer.java:1699)
     at com.hyperion.cis.config.AppServerDeployer.initializeParameters(AppServerDeployer.java:169)
     at com.hyperion.config.wizard.impl.RunAllTasks.executeAppDeploymentTask(RunAllTasks.java:636)
     at com.hyperion.config.wizard.impl.RunAllTasks.execute(RunAllTasks.java:331)
     at com.hyperion.config.wizard.impl.RunnAllTasksState.run(RunnAllTasksState.java:89)
     at java.lang.Thread.run(Thread.java:619)
[2010-05-09T06:57:03.804-06:00] [EPMCFG] [ERROR] [EPMCFG-01020] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.foundation.config.OCMTaskProcessor] Error: [[
java.lang.NullPointerException
     at com.hyperion.foundation.config.OCMTaskProcessor.uploadOCMConfigurationToRegistry(OCMTaskProcessor.java:209)
     at com.hyperion.foundation.config.OCMTaskProcessor.execute(OCMTaskProcessor.java:95)
     at com.hyperion.cis.CustomTaskProcessor.execute(CustomTaskProcessor.java:94)
     at com.hyperion.config.wizard.impl.RunAllTasks.executeCustomTask(RunAllTasks.java:725)
     at com.hyperion.config.wizard.impl.RunAllTasks.execute(RunAllTasks.java:313)
     at com.hyperion.config.wizard.impl.RunnAllTasksState.run(RunnAllTasksState.java:89)
     at java.lang.Thread.run(Thread.java:619)
[2010-05-09T06:57:07.992-06:00] [EPMCFG] [ERROR] [EPMCFG-02151] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.hit.fusion.FusionComponent] oracleComponent is null. Component will not be provisioned.
[2010-05-09T06:57:07.992-06:00] [EPMCFG] [TRACE] [EPMCFG-01001] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.config.wizard.impl.RunAllTasks] trace: Component provisioning is done.
[2010-05-09T06:57:07.992-06:00] [EPMCFG] [TRACE] [EPMCFG-01001] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.config.wizard.impl.RunAllTasks] trace: Done sorting tasks by priority
[2010-05-09T06:57:07.992-06:00] [EPMCFG] [TRACE] [EPMCFG-07326] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.config.wizard.impl.RunAllTasks] Executing deployment task for ProductDescriptor [workspace]
[2010-05-09T06:57:07.992-06:00] [EPMCFG] [TRACE] [EPMCFG-01328] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.cis.config.ConfigRegistryUtils] Looking for product component in the registry: component type = SHARED_SERVICES_PRODUCT
[2010-05-09T06:57:08.007-06:00] [EPMCFG] [ERROR] [EPMCFG-01020] [oracle.EPMCFG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.config.wizard.impl.RunAllTasks] Error: [[
java.lang.NullPointerException
     at com.hyperion.cis.config.AppServerDeployer.isDeployAsWinService(AppServerDeployer.java:1699)
     at com.hyperion.cis.config.AppServerDeployer.initializeParameters(AppServerDeployer.java:169)
     at com.hyperion.config.wizard.impl.RunAllTasks.executeAppDeploymentTask(RunAllTasks.java:636)
     at com.hyperion.config.wizard.impl.RunAllTasks.execute(RunAllTasks.java:331)
     at com.hyperion.config.wizard.impl.RunnAllTasksState.run(RunnAllTasksState.java:89)
     at java.lang.Thread.run(Thread.java:619)
Registry.log:
[2010-05-09T06:51:46.860-06:00] [EPMREG] [NOTIFICATION] [EPMREG-51096] [oracle.EPMREG.REG] [tid: 14] [ecid: 0000IXx7j^D37E65zNd9iW1BtexF000005,0] [SRC_CLASS: com.hyperion.hit.registry.RegistryUtils] [SRC_METHOD: readDatabaseProperties] Security Key could not be read from reg.properties file.
[2010-05-09T06:55:33.719-06:00] [EPMREG] [ERROR] [EPMREG-11054] [oracle.EPMREG.REG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.hit.registry.RegistryConnection] [SRC_METHOD: createRegistry] [arg: C:\Oracle\Middleware\EPMSystem11R1\common\config\11.1.2.0\resources\registry\create_oracle.sql] An SQL Exception executing the registry DDL script C:\Oracle\Middleware\EPMSystem11R1\common\config\11.1.2.0\resources\registry\create_oracle.sql.
[2010-05-09T06:55:33.735-06:00] [EPMREG] [ERROR] [EPMREG-11099] [oracle.EPMREG.REG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.hit.registry.RegistryConnection] [SRC_METHOD: createRegistry] Exception occurred.[[
java.sql.SQLSyntaxErrorException: ORA-00917: missing comma
     at oracle.jdbc.driver.SQLStateMapping.newSQLException(SQLStateMapping.java:91)
     at oracle.jdbc.driver.DatabaseError.newSQLException(DatabaseError.java:133)
     at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:206)
     at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:455)
     at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:413)
     at oracle.jdbc.driver.T4C8Oall.receive(T4C8Oall.java:1035)
     at oracle.jdbc.driver.T4CStatement.doOall8(T4CStatement.java:183)
     at oracle.jdbc.driver.T4CStatement.executeForRows(T4CStatement.java:942)
     at oracle.jdbc.driver.OracleStatement.doExecuteWithTimeout(OracleStatement.java:1223)
     at oracle.jdbc.driver.OracleStatement.executeInternal(OracleStatement.java:1775)
     at oracle.jdbc.driver.OracleStatement.execute(OracleStatement.java:1744)
     at oracle.jdbc.driver.OracleStatementWrapper.execute(OracleStatementWrapper.java:299)
     at com.hyperion.hit.registry.RegistryConnection.createRegistry(RegistryConnection.java:241)
     at com.hyperion.hit.registry.RegistryUtils.initRegistry(RegistryUtils.java:82)
     at com.hyperion.hit.registry.Registry.createRegistry(Registry.java:2220)
     at com.hyperion.config.document.Storage.createRegProperties(Storage.java:1396)
     at com.hyperion.config.wizard.impl.RunAllTasks.execute(RunAllTasks.java:105)
     at com.hyperion.config.wizard.impl.RunnAllTasksState.run(RunnAllTasksState.java:89)
     at java.lang.Thread.run(Thread.java:619)
[2010-05-09T06:56:03.456-06:00] [EPMREG] [ERROR] [EPMREG-11037] [oracle.EPMREG.REG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.hit.registry.Registry] [SRC_METHOD: getConnection] An error occured when checking the status of the registry connection and reseting it.[[
com.hyperion.hit.registry.exceptions.RegistryException: No database properties could be read
     at com.hyperion.hit.registry.datasource.SharedServicesDataSourceFactory.getDataSource(SharedServicesDataSourceFactory.java:29)
     at com.hyperion.hit.registry.datasource.SharedServicesDatabaseConnectionBuilder.getConnection(SharedServicesDatabaseConnectionBuilder.java:26)
     at com.hyperion.hit.registry.RegistryUtils.createNewConnection(RegistryUtils.java:183)
     at com.hyperion.hit.registry.Registry.getConnection(Registry.java:161)
     at com.hyperion.hit.registry.Registry.lookupComponents(Registry.java:1263)
     at com.hyperion.hit.registry.Registry.lookup(Registry.java:517)
     at com.hyperion.css.registry.RegistryManager.<init>(RegistryManager.java:70)
     at com.hyperion.css.registry.RegistryManager.populateCSSTrustedServicesKey(RegistryManager.java:140)
     at com.hyperion.foundation.config.FoundationDbConfigurator.populateCssTrustedKey(FoundationDbConfigurator.java:121)
     at com.hyperion.foundation.config.FoundationDbConfigurator.configure(FoundationDbConfigurator.java:88)
     at com.hyperion.config.wizard.impl.RunAllTasks.executeDbConfigTask(RunAllTasks.java:753)
     at com.hyperion.config.wizard.impl.RunAllTasks.execute(RunAllTasks.java:322)
     at com.hyperion.config.wizard.impl.RunnAllTasksState.run(RunnAllTasksState.java:89)
     at java.lang.Thread.run(Thread.java:619)
[2010-05-09T06:56:03.456-06:00] [EPMREG] [ERROR] [EPMREG-11045] [oracle.EPMREG.REG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.hit.registry.Registry] [SRC_METHOD: lookupComponents] [arg: SYSTEM9] An exception when looking up components of type SYSTEM9 matching the specified properties.
[2010-05-09T06:56:03.456-06:00] [EPMREG] [ERROR] [EPMREG-11099] [oracle.EPMREG.REG] [tid: 27] [ecid: 0000IXx8^W937E65zNd9iW1BtexF00000G,0] [SRC_CLASS: com.hyperion.hit.registry.Registry] [SRC_METHOD: lookupComponents] Exception occurred.[[
com.hyperion.hit.registry.exceptions.RegistryException: com.hyperion.hit.registry.exceptions.RegistryException: No database properties could be read
     at com.hyperion.hit.registry.Registry.getConnection(Registry.java:178)
     at com.hyperion.hit.registry.Registry.lookupComponents(Registry.java:1263)
     at com.hyperion.hit.registry.Registry.lookup(Registry.java:517)
     at com.hyperion.css.registry.RegistryManager.<init>(RegistryManager.java:70)
     at com.hyperion.css.registry.RegistryManager.populateCSSTrustedServicesKey(RegistryManager.java:140)
     at com.hyperion.foundation.config.FoundationDbConfigurator.populateCssTrustedKey(FoundationDbConfigurator.java:121)
     at com.hyperion.foundation.config.FoundationDbConfigurator.configure(FoundationDbConfigurator.java:88)
     at com.hyperion.config.wizard.impl.RunAllTasks.executeDbConfigTask(RunAllTasks.java:753)
     at com.hyperion.config.wizard.impl.RunAllTasks.execute(RunAllTasks.java:322)
     at com.hyperion.config.wizard.impl.RunnAllTasksState.run(RunnAllTasksState.java:89)
     at java.lang.Thread.run(Thread.java:619)
Caused by: com.hyperion.hit.registry.exceptions.RegistryException: No database properties could be read
     at com.hyperion.hit.registry.datasource.SharedServicesDataSourceFactory.getDataSource(SharedServicesDataSourceFactory.java:29)
     at com.hyperion.hit.registry.datasource.SharedServicesDatabaseConnectionBuilder.getConnection(SharedServicesDatabaseConnectionBuilder.java:26)
     at com.hyperion.hit.registry.RegistryUtils.createNewConnection(RegistryUtils.java:183)
     at com.hyperion.hit.registry.Registry.getConnection(Registry.java:161)
     ... 10 more

Yes. I downloaded and extracted the additional components. I have also dropped and recreated the HSS repository. Each time I have tried to reinstall, I have uninstalled all EPM/Oracle components, removed registry keys, removed EPM environment variables and removed references to oracle in the PATH environment variable.
I have tried installing/configuring HSS 11.1.2 on both Windows 2008 SP1 64-bit and Windows 2008 SP1 32-bit. The configuration error is the same.
I was able to get my SR reassigned to a different support analyst, and we are working on troubleshooting now.
If you can think of anything else to try, let me know.
BTW...on the 32-bit server, the page file maximum is 16GB (should be enough)?
Thanks.

Windows 2008 r2 WSUS port 8530

Similar Messages

Maybe you are looking for