Windows 7 32 b ipsec client to RV220W error 789

Hello,
I try to connect to RV220W with windows 7 client but  I fail : error 789. I compare again and again pre shared key, but it doesn't change anything
Is anybody connect to RV220W with IPsec client ?
Thanks

GF, this is not an ipsec vpn and it is not as secure. The only built-in window support will be PPTP in regards to connecting to the router.
If you're looking for IPsec, you need to use quickvpn (free Cisco software) or a 3rd party software such as greenbow, shrewsoft, ipsecuritas, etc.
-Tom
Please rate helpful posts

Similar Messages

  • RV042G VPN - How to connect with Windows 7 IPsec client?

    Hello,
    I'm trying to use the Windows 7 VPN client, to connect to my RV042G. Here are some Screenshots of my router's and Windows' configuration:
    I tried different other configurations, too, but each time, I get a lot of errors on the router. The upper configuration results in the following:
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [MS NT5 ISAKMPOAKLEY 00000008]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [MS NT5 ISAKMPOAKLEY 00000008]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: received Vendor ID payload [RFC 3947]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: received Vendor ID payload [RFC 3947]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [FRAGMENTATION]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [FRAGMENTATION]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [fb1de3cdf341b7ea16b7e5be0855f120]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [fb1de3cdf341b7ea16b7e5be0855f120]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [Vid-Initial-Contact]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [Vid-Initial-Contact]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [e3a5966a76379fe707228231e5ce8652]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: ignoring Vendor ID payload [e3a5966a76379fe707228231e5ce8652]
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: [Tunnel Negotiation Info] <<< Responder Received Main Mode 1st packet
    Feb 13 14:58:05 2014     VPN Log     packet from 192.168.1.24:500: [Tunnel Negotiation Info] <<< Responder Received Main Mode 1st packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: responding to Main Mode from unknown peer 192.168.1.24
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: OAKLEY_AES_CBC is not enabled for this connection. Attribute OAKLEY_ENCRYPTION_ALGORITHM
    Feb 13 14:58:05 2014    Kernel     last message repeated 5 times
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: OAKLEY_GROUP_MODP2048 is not enabled for this connection. Attribute OAKLEY_GROUP_DESCRIPTION
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: OAKLEY_GROUP_MODP2048 is not enabled for this connection. Attribute OAKLEY_GROUP_DESCRIPTION
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] >>> Responder Send Main Mode 2nd packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] >>> Responder Send Main Mode 2nd packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] <<< Responder Received Main Mode 3rd packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] <<< Responder Received Main Mode 3rd packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] >>> Responder send Main Mode 4th packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] >>> Responder send Main Mode 4th packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] <<< Responder Received Main Mode 5th packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] <<< Responder Received Main Mode 5th packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: Peer ID is ID_IPV4_ADDR: '192.168.1.24'
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] >>> Responder Send Main Mode 6th packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] >>> Responder Send Main Mode 6th packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] Main Mode Phase 1 SA Established
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] Main Mode Phase 1 SA Established
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: sent MR3, ISAKMP SA established
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] <<< Responder Received Quick Mode 1st packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: [Tunnel Negotiation Info] <<< Responder Received Quick Mode 1st packet
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: cannot respond to IPsec SA request because no connection is known for 78.52.27.132:17/1701...192.168.1.24[[email protected]]:17/1701
    Feb 13 14:58:05 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: sending encrypted notification INVALID_ID_INFORMATION to 192.168.1.24:500
    Feb 13 14:58:07 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x00000001 (perhaps this is a duplicated packet)
    Feb 13 14:58:07 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x00000001 (perhaps this is a duplicated packet)
    Feb 13 14:58:07 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: sending encrypted notification INVALID_MESSAGE_ID to 192.168.1.24:500
    Feb 13 14:58:10 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x00000001 (perhaps this is a duplicated packet)
    Feb 13 14:58:10 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x00000001 (perhaps this is a duplicated packet)
    Feb 13 14:58:10 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: sending encrypted notification INVALID_MESSAGE_ID to 192.168.1.24:500
    Feb 13 14:58:14 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x00000001 (perhaps this is a duplicated packet)
    Feb 13 14:58:14 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x00000001 (perhaps this is a duplicated packet)
    Feb 13 14:58:14 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: sending encrypted notification INVALID_MESSAGE_ID to 192.168.1.24:500
    Feb 13 14:58:22 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x00000001 (perhaps this is a duplicated packet)
    Feb 13 14:58:22 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x00000001 (perhaps this is a duplicated packet)
    Feb 13 14:58:22 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: sending encrypted notification INVALID_MESSAGE_ID to 192.168.1.24:500
    Feb 13 14:58:38 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x00000001 (perhaps this is a duplicated packet)
    Feb 13 14:58:38 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x00000001 (perhaps this is a duplicated packet)
    Feb 13 14:58:38 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: sending encrypted notification INVALID_MESSAGE_ID to 192.168.1.24:500
    Feb 13 14:58:52 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: received Delete SA payload: deleting ISAKMP State #89
    Feb 13 14:58:52 2014     VPN Log     (c2gips0)[2] 192.168.1.24 #89: received Delete SA payload: deleting ISAKMP State #89
    Feb 13 14:58:52 2014     VPN Log     (c2gips0)[2] 192.168.1.24: deleting connection (c2gips0) instance with peer 192.168.1.24 {isakmp=#0/ipsec=#0}
    Does anyone know, how to configure the router and Windows 7, to get a working VPN tunnel?
    Thanks.

    Ok, I could find the time, to try this out. I followed this instruction: https://www.shrew.net/support/Howto_Linksys and it works.
    There is at last one Problem: I can't access computers behind the remote router from the connected client. The client can see the remote router and computers behind the remote router can see the connected client using the IP-adress, I used for shrewsoft.
    I tried to ping some remote PCs from the client, but I get timeout messages. Ping is enabled on all devices. There are no log errors on the router. I tried to add the remote router on the client as a standard gateway, and I decativated the router's firewall, but without success.
    Does anyone know, why the communication just works in one direction?

  • New windows 8.1 clients getting certificate error

    We are running exchange 2010 and one of our end-users just recently purchased a windows 8.1 laptop.  When he tries to connect to exchange using the built-in mail app, he gets the error, "To connect to this account, you need a valid certificate
    on this PC.  Contact your system administrator for more info"
    I searched a lot online and found a suggestion of signing into OWA and exporting the root level certificate, then installling it.  I did that, but still receive the error on his machine. 
    Any suggestions?

    Hi,
    Supplementing a blog for your reference:
    Supporting Windows Mail 8.1 in your organization
    http://blogs.technet.com/b/exchange/archive/2013/10/18/supporting-windows-mail-8-1-in-your-organization.aspx
    Hope it is helpful
    Thanks
    Mavis
    Mavis Huang
    TechNet Community Support

  • RDS invalid licensing Windows Server 2003 Client

    I have two Windows Server 2012 Session Host Server and two Windows 2012 Connection Brokers. One Connection Broker configured with remote desktop License.We are Using License type is per device cal.
    On Server A, I can access RDP from Windows 7 clients and from Windows XP clients Windows Server 2003 Clients.
    On Server B I can only RDP from Windows 7 clients and Windows XP Clients NOT from Windows Server 2003 Clients). The error is"The remote session was disconnected because the remote computer received an invalid licensing message from this computer"

    Hi Gyan,
    Which version of client RDP you are using in your environment?
    Did you receive any particular Event ID during this issue?
    Here for your issue I found something to let u know, if licensing mode on the terminal server is set to Per Device but the license server is configured to issue only Per User CALs, then only temporary Per Device licenses are issued from the available pool of
    licenses. The license cannot upgraded. 
    Please check the license is properly configured and activated. If not then you can contact MS clearing house or try to change the terminal server licensing mode.
    Please refer below link for more information.
    The remote session was disconnected because the local computer's client access license could not be upgraded or renewed
    http://technet.microsoft.com/en-us/library/cc737592(v=ws.10).aspx
    You need to verify the terminal server because it can’t able to locate the license server.
    The terminal server cannot locate the license server
    http://technet.microsoft.com/en-us/library/cc758805(v=ws.10).aspx
    Hope it helps!
    Regards.

  • How do I resolve this error in windows server 2012 MANTENIMIENTOTS_1306_Error_Microsoft-Windows-TerminalServices-SessionBroker-Client_Microsoft-Windows-TerminalServices-SessionBroker-Client/Operational_03/03/2014 8:09:18 a. m.

    Como solucionar error 
    MANTENIMIENTOTS
    1306
    Error
    Microsoft-Windows-TerminalServices-SessionBroker-Client
    Microsoft-Windows-TerminalServices-SessionBroker-Client/Operational
    03/03/2014 8:09:18 a. m.
    de windows server 2012

    What exactly you are asking? Please use English language so we can start helping you out. I believe this error seems to be related to Terminal Server. You have to ask your question in appropriate forum in that case. All in all you have to clarify your question
    or the thread will not moved or answered. :)
    Regards.
    Mahdi Tehrani Loves Powershell
    Please kindly click on Propose As Answer or to mark this post as
    and helpfull to other poeple.

  • Windows 7 KMS client activation error

    hi,
    Windows 7 KMS client activation error
    Any known issue?
    Thanks

    This problem occurs if the KMS server does not find a valid Windows marker in the ACPI_SLIC table in the computer's BIOS program. This problem occurs for one of the following reasons.
    Cause 1
    You purchased a computer that has a qualifying Windows operating system installed. However, the Windows marker in the ACPI_SLIC table is corrupted.
    Cause 2
    You purchased a computer that does not have a qualifying Windows operating system installed. In this case, the Windows marker is not present in the ACPI_SLIC table.

  • Can't open secured documents on windows 7 domain client with mandatory profiles.

    While opening certain PDF files we have the problem that the user is presented with a message that he does not have the rights permissions. This happens twice, after that the users gets an empty page with the message the Adobe version might not be up to date. We use Acrobat Pro 10, but this also happens while using Reader 11.0.8. On our windows 2008 terminal services machine this could be fixed by giving the user rights on c:\ to create and remove a file. :O. On windows 7 this doesn't work probably because of UAC. But we've tried every solution to that available on the internet, disabling uac, changing uac options, changing rights on userprofile folders, changing rights on c:\ but to no avail. When using process explorer we can see it wants to create a temp file p328hkl.tmp or something like that on C but it can't and immediattely after is shows the error on screen.
    Anyone who also has this problem or solved it? There are no problems with simple self made pdf files/scans but only with certain types of pdf files for which it tries to create a tmp file.
    Thanks,
    Peter

    Hi Brogers,
    Thanks for your reaction. We do have AppData redirection in place. We redirect AppData to a share on our data server which works perfectly fine for all other applications. The weird thing is that Reader/Acrobat try to write to C:\ which to my knowledge should not happen, is this maybe a fallback because it can’t write to a different location? Users have full control on their own roaming AppData but not on their local AppData that is made by windows itself while copying the mandatory default profile to C:\.
    I might use the wrong term while saying secured documents. I’m talking about a document created by Raet/Youforce a web application for personal administration. The documents can be opened by other viewers than Acrobat/Reader but then only contain the background and not the text. In Acrobat/Reader they do open normally when Acrobat/Reader can create the .tmp file. Otherwise it will not display the file at all. I would attach such a document to see but since it contains certain info I am not allowed to do so.
    I hope we can work out a solution for this.
    Met vriendelijke groet,
    Peter Gerritsen
    Engineer
    AndoBurg BV
    Voorstraat 31
    3931 HB Woudenberg
    T 033 479 40 80
    F 033 479 40 89
    E [email protected]<mailto:[email protected]>
    I www.andoburg.com<http://www.andoburg.com/>
    Als u niet de geadresseerde van dit bericht bent, verzoeken wij u ons hiervan op de hoogte te brengen en het bericht te verwijderen. AndoBurg BV aanvaardt geen aansprakelijkheid voor schade die voortvloeit uit elektronische verzending van informatie. Aan de inhoud van deze e-mail en eventuele bijlagen kunnen geen rechten worden ontleend, tenzij schriftelijk anders is overeengekomen.
    Van: brogers_1
    Verzonden: vrijdag 19 september 2014 20:10
    Aan: Peter Gerritsen
    Onderwerp:  Can't open secured documents on windows 7 domain client with mandatory profiles.
    Can't open secured documents on windows 7 domain client with mandatory profiles.
    created by brogers_1<https://forums.adobe.com/people/brogers_1> in Enterprise Deployment (Acrobat and Reader) - View the full discussion<https://forums.adobe.com/message/6745441#6745441>

  • Getting error 789 when trying to connect with a PC remotely via VPN

    When we set up the VPN we are getting a Error 789 when trying to connect with a PC. Any suggestions would be appreciated.

    The utilities, provided on the CD, are not required for the PC to access the Internet through the 802.11n AirPort Extreme Base Station (AEBSn). They are only necessary for administering the base station.
    If your PC is currently configured as a DHCP client, it shouldn't have any issues connecting by Ethernet. The AEBSn will assign the appropriate IP addresses required for connectivity to the Internet ... just like it does for wireless clients.

  • On windows 7 , SAP B1 showing internal error.

    Dear Friends,
    1) on XP my sap client is working fine.
    2) on windows 7 , it is showing internal error.
    Means- while we do change server and put SERVER ,then login ID - sa , then Password.At thet time system showing internal error.
    Txs,
    Mahesh.

    Dear Mahesh,
    Firstly, I would suggest to read notes related to Windows 7; notes numbers 1493833, 1434624 and any other notes these 2 refer to.
    If this does not help, please come back to us specifying the exact error you get and the exact steps you are taking.
    Regards,
    Marcella Rivi
    SAP Business One Forums Team

  • Windows 8.1 Network Share 0x8007003b Error Copying Files

    Hi All,
    I'm having an issue when copying files from a Windows network share. If the file is above 5MB it will start copying and then after a minute or two I will get an error such as:
    Interrupted Action
    An unexpected error is keeping you from copying the file. If you continue to receive this error, you can use the error code to search for help with this problem.
    Error 0x8007003B: An unexpected network error occurred.
    The network share is in a different office and is accessible over a point-to-point VPN, so the connection is not that fast. 
    But before everyone tells me to start diagnosing the router and or VPN please take note of the following:
    My colleague who is running Windows 7 can copy files from the network share fine
    If I run a Windows 7 VM on my Windows 8.1 laptop I can copy the files across fine
    I also know it isn't an issue with this particular file share. I set up a little lab, where I had one VM which had a shared folder and 2 other client VMs one running Windows 7 and one running Windows 8.1. I limited the bandwidth to the two client
    VMs to a similar speed we see across our VPN. The result was that the Windows 8.1 failed with the same error above, whereas the Windows 7 copied fine.
    There is also a noticeable difference visually when copying using Windows 8.1 and Windows 7:
    Windows 7 - The progress bar progresses smoothly giving the current speed and estimated time remaining
    Windows 8.1 - The progress bar progresses in a jumpy fashion. E.g. it shows no progress, then after a minute it jumps and shows 16% progress, then shows no further progress, then jumps by another 18%. There is no estimated time remaining.
    I ran Wireshark to investigate what was going on at the network layer. I see the following behaviour:
    Windows 8.1 - The file is copying fine then all of a sudden there are a lot of TCP dupack packets. After which the Windows 8.1 client sends a RST packet and then the error pops up.
    Windows 7 - The file is copying fine then you also see a load of TCP dupack packets, however no error is displayed and it continues copying fine.
    I'd appreciate any help with this I'm hoping there are some settings I can change to make Windows 8.1 behave more like Windows 7!
    FYI originally posed here (but was advised to ask on Technet) - https://answers.microsoft.com/en-us/windows/forum/windows8_1-files/windows-81-network-share-0x8007003b-error-copying/300bc9a4-597b-402a-b885-9dd6f6fb51a2
    Thanks,
    Zak

    Hi MeipoXu,
    Sorry, it has taken me so long to reply. I thought I had subscribed to receive updates on this thread, but I didn't see anything!
    I've ran the commands you gave but some of them did not work, I got the following error: 
    Set global command failed on IPv4 The parameter is incorrect.
    However, output of current settings are below.
    TCP Global Parameters
    Receive-Side Scaling State          : disabled
    Chimney Offload State               : disabled
    NetDMA State                        : disabled
    Direct Cache Access (DCA)           : disabled
    Receive Window Auto-Tuning Level    : normal
    Add-On Congestion Control Provider  : none
    ECN Capability                      : disabled
    RFC 1323 Timestamps                 : disabled
    Initial RTO                         : 3000
    Receive Segment Coalescing State    : disabled
    Non Sack Rtt Resiliency             : disabled
    Max SYN Retransmissions             : 2
    To answer your original questions.
    Do you mean the file below 5 MB will copy fine ?
    5MB is not a hard limit. If the file is small enough it will copy before it errors out. A file of around 5MB or so fails with an error.
    Have you tried to copy the files from another Windows 8.1 machine (This will help us to verify whether the issue is casued by the specific machine)?Have you tried to copy another file from the network share to have a check ?
    Yes I've tried from another Windows 8.1 machine and have the same behaviour. It is the same with different files from the network share. And the same with different network shares.
    I am seeing nothing in the event viewer when the error occurs. I do not believe this to be a VPN issue because I can recreate this situation perfectly. As I mentioned in the original post- I
    also know it isn't an issue with this particular file share. I set up a little lab, where I had one VM which had a shared folder and 2 other client VMs one running Windows 7 and one running Windows 8.1. I limited the bandwidth to the two client VMs to a similar
    speed we see across our VPN. The result was that the Windows 8.1 failed with the same error above, whereas the Windows 7 copied fine.
    Basically, I had virtual machines all on the same local network. One virtual machine was hosting a file share with files on it. I created one Windows 7 VM and one Windows 8.1 VM. Using VMWare Workstation you can limit the network bandwidth to the VMs. When
    I did not limit the network bandwidth I could copy all files of all sizes fine. However, when I limit the network bandwidth to a speed of around 30-50KBps, the Windows 8.1 VM fails to copy files with the same error. But Windows 7 VM copies the files fine.
    The point of limiting the bandwidth in this way is to create a similar scenario to that I see when connecting over the VPN.
    This all leads me to believe there is some sort of issue with copying files from fileshares over slow connections using Windows 8.1.
    Cheers,
    Zak

  • Automatic Install of Endpoint Protection fails on windows 8.1 clients with SCCM 2012 R2

    Running SCCM 2012 R2 and deploying CM clients and Endpoint Protection via software updates. CM client and EP install fine on Windows 7 clients. CM client installs fine but endpoint protection fails on Windows 8.1 clients with the following from the
    endpoint protection agent log:
    <![LOG[Create Process Command line: "C:\Windows\ccmsetup\SCEPInstall.exe" /s /q /policy "C:\Windows\CCM\EPAMPolicy.xml".]LOG]!><time="12:22:02.560+240" date="08-13-2014" component="EndpointProtectionAgent"
    context="" type="1" thread="4260" file="epagentutil.cpp:607">
    <![LOG[Detail error message is : [EppSetupResult]
    HRESULT=0x80070643
    Description=Cannot complete the System Center Endpoint Protection installation. An error has prevented the System Center Endpoint Protection setup wizard from completing successfully. Please restart your computer and try again. Error code:0x80070643. Fatal
    error during installation.
    So on the win8.1 client I run the above command line manually in a command window and receive Access is denied. Then I run the same command in an elevated command window and EP installs fine. Does this have something to do with why the automatic
    EP client install fails with the 0x80070643 error code? If so, what is the fix?

    Hi,
    Try uninstalling any other security software.
    For more information, please review the link below:
    I‘m getting an error code from my Microsoft security software
    http://www.microsoft.com/security/portal/mmpc/help/errorcodes.aspx
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Windows 8.1 client backup fails every time at 1%

    I have just added a brand new Win 8.1 client to the network, installed the connector etc. However the SBS backup repeatedly fails at 1%. I have seen similar posts that refer to drive errors, missing partitions etc, but this is a new device.
    The log states:
    "Windows server client computer backup service received an abort process message from <computername>. Reason: 5"
    So the client is doing something to interrupt the backup but I cannot find what '5' means.  When I click the link in the log message it returns 'nothing found'!  I have changed the power settings so the laptop does not sleep but that makes no difference.
    It also makes no difference if the backup is initiated from the server dashboard or the client connector.
    Any advice appreciated!
    Andrew
    Andrew

    Hi Andrew,
    Before going further, would you please let me confirm whether only that new Windows 8.1 client computer encounter
    this issue?
    Please logon the SBS 2011 and open Dashboard. Then select Computers and Backup tab and navigate to this Windows
    8.1 client computer. Please check if the Status of the Windows 8.1 client computer shows as
    Online. Did find any Critical or Warning information in Alerts? If click that problematic Windows 8.1 on the Dashboard and select
    Start a backup for the computer task, will encounter the same issue?
    Meanwhile, please follow the path:
    C:\ProgramData\Microsoft\Windows Server\Logs, then check some relevant backup log files if find more clues.
    Key
    Small Business Server 2011 Essentials Log Files
    If any update, please feel free to let me know.
    Hope this helps.
    Best regards,
    Justin Gu

  • WIndows 7 Pro 64 Bit Update Error ode 537

    The Office 2013 Update installed on 10 PCs but failed on 1 with the error code 537- unknown error.
    I tried rebooting, running FixIt and SFC /scannow but I get the same error message every time.

    I tried running Update in Safe Mode but it does not run. When I tried to active the Windows Update Service I got an error message that Update does not run in Safe Mode.
    I then stopped all 3rd party processes and services using MSCONFIG, deleted all files in the SoftwareDistribution folder, rebooted and tried to run Update - still failed.
    I tried MS FixIT and ran Chkdsk then tried Update again - still failed.
    Other updates install correctly (MSE signatures) so the problem appears to be with the MSO 2013 update.
    Based on the error code 0x80070643 in the ReportingEvents file it appears that the problem is with .Net Framework. Next step is to try to repair .NetFramework. Any other recommendations?
    {3300EE1F-E526-4BED-9751-A1FB24CDBE28}    2014-07-16 16:16:30:605-0400    1    148    101    {00000000-0000-0000-0000-000000000000}    0    8024a005  
     AutomaticUpdates    Failure    Software Synchronization    Windows Update Client failed to detect with error 0x8024a005.
    {2CFC3945-142D-4D99-B6D6-3D7A5DFDA6FE}    2014-07-16 16:20:41:563-0400    1    147    101    {00000000-0000-0000-0000-000000000000}    0    0  
     AutomaticUpdates    Success    Software Synchronization    Windows Update Client successfully detected 4 updates.
    {37C62A10-9CF3-4A4A-9729-6679B0E4420A}    2014-07-16 16:22:16:676-0400    1    162    101    {86CF7F8E-41D5-4424-B176-CBB5F0D1C151}    200    0  
     AutomaticUpdatesWuApp    Success    Content Download    Download succeeded.
    {B6C9C697-796B-4C1B-966A-DA00553103B4}    2014-07-16 16:22:16:676-0400    1    188    102    {00000000-0000-0000-0000-000000000000}    0    0  
     AutomaticUpdates    Success    Content Install    Installation Ready: The following updates are downloaded and ready for installation. This computer is currently scheduled to install these updates on ‎Thursday,
    ‎July ‎17, ‎2014 at 12:00 AM:  - Update for Microsoft Office 2013 (KB2880987) 64-Bit Edition
    {520070B9-3717-4D30-A7A1-2665DD2BBA62}    2014-07-16 16:23:19:919-0400    1    182    101    {86CF7F8E-41D5-4424-B176-CBB5F0D1C151}    200    80070643  
     AutomaticUpdates    Failure    Content Install    Installation Failure: Windows failed to install the following update with error 0x80070643: Update for Microsoft Office 2013 (KB2880987) 64-Bit Edition.
    {CDA9A718-BC41-4DD3-A93B-B1FAEEE731F8}    2014-07-16 16:23:41:353-0400    1    188    102    {00000000-0000-0000-0000-000000000000}    0    0  
     AutomaticUpdates    Success    Content Install    Installation Ready: The following updates are downloaded and ready for installation. This computer is currently scheduled to install these updates on ‎Thursday,
    ‎July ‎17, ‎2014 at 12:00 AM:  - Update for Microsoft Office 2013 (KB2880987) 64-Bit Edition

  • How configure Windows 8.1 Clients with IE11 for SSO with Kerberos SPNEGO

    We are using BI Publisher OBIEE 11.1.1.7 with SSO Kerberos SPNEGO.
    The Weblogic Server Version is WLS_PRODUCT_VERSION=10.3.5.0
    The SSO is working very well with Clients that are Windows XP or Windows 2003 R2. We had testet wit IE7,IE8 Firefox.
    Now as we become Windows 8.1 Clients with IE11 the Kerberos SPNEGO SSO is not working.
    Please give us advice or a HOW TO Document about the configuration on Windows 8.1 Cllients with IE11 Browser.
    I find many Dokuments related to older Windows Versions for example
    http://www.oracle.com/technetwork/articles/idm/weblogic-sso-kerberos-1619890.html
    but nothing for Windows 8.1 Clients
    Thanks in advance.

    The location for tabs in IE11 browser might be different but the steps are the same :
    Configure Local Intranet Domains
       1. In Internet Explorer, select Tools > Internet Options.
       2. Select the Security tab.
       3. Select Local intranet and click Sites.
       4. In the Local intranet popup, ensure that the Include all sites that bypass the proxy server and Include all local (intranet) sites not listed in other zones options are checked.
       5. Click Advanced.
       6. In the Local intranet (Advanced) dialog box, add all relative domain names that will be used for Oracle WebLogic Server instances participating in the SSO configuration (for example, myhost.example.com) and click OK.
    Configure Intranet Authentication
       1. Select Tools > Internet Options.
       2. Select the Security tab.
       3. Select Local intranet and click Custom Level... .
       4. In the Security Settings dialog box, scroll to the User Authentication section.
       5. Select Automatic logon only in Intranet zone. This option prevents users from having to re-enter logon credentials, which is a key piece to this solution.
       6. Click OK.
    Verify Proxy Settings
    If you have a proxy server enabled:
       1. Select Tools > Internet Options.
       2. Select the Connections tab and click LAN Settings.
       3. Verify that the proxy server address and port number are correct.
       4. Click Advanced.
       5. In the Proxy Settings dialog box, ensure that all desired domain names are entered in the Exceptions field.
       6. Click OK to close the Proxy Settings dialog box.
    What is the error reported by the browser / wls logs ?
    -- Puneeth

  • ORA-12518: TNS:listener could not hand off client connection (DBD ERROR: OCIServerAttach)

    Hi again,
    I'm on my enterprise management console and Database Instance and Listener shows the green arrow, but the Agent Connection to Instance shows a red downward arrow and the error:
    Status: Failed
    Details: ORA-12518: TNS:listener could not hand off client connection (DBD ERROR: OCIServerAttach)
    My OraClrAgnt service is up and running (using winxp pro, oracle 11gR2), I'm on my home pc, all my ports are open (my machine's name is "abigail" and it is dmzhost)
    Any suggestions to resolve this error?
    My Tnsnames ora:
    ABIGAIL =
      (DESCRIPTION =
        (ADDRESS_LIST =
          (ADDRESS = (PROTOCOL = TCP)(HOST = ABIGAIL)(PORT = 1521))
        (CONNECT_DATA =
          (SERVICE_NAME = orcl.0.0.10)
    LISTENER_ORCL =
      (DESCRIPTION =
        (ADDRESS_LIST =
          (ADDRESS = (PROTOCOL = TCP)(HOST = ABIGAIL)(PORT = 1521))
        (CONNECT_DATA =
          (SID = ORCL)
    RMAN =
      (DESCRIPTION =
        (ADDRESS = (PROTOCOL = TCP)(HOST = ABIGAIL)(PORT = 1521))
        (CONNECT_DATA =
          (SERVER = DEDICATED)
          (SERVICE_NAME = rman.abigail)
    My listener.ora
    SID_LIST_LISTENER =
      (SID_LIST =
        (SID_DESC =
          (SID_NAME = CLRExtProc)
          (ORACLE_HOME = E:\app\abigail\product\11.2.0\dbhome_1)
          (PROGRAM = extproc)
          (ENVS = "EXTPROC_DLLS=ONLY:E:\app\abigail\product\11.2.0\dbhome_1\bin\oraclr11.dll")  
    LISTENER =
      (DESCRIPTION_LIST =
        (DESCRIPTION =
          (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521))
          (ADDRESS = (PROTOCOL = TCP)(HOST = ABIGAIL)(PORT = 1521))
    ADR_BASE_LISTENER = E:\app\abigail
    My SQLNET.ORA
    SQLNET.AUTHENTICATION_SERVICES= (NTS)
    NAMES.DIRECTORY_PATH= (EZCONNECT, TNSNAMES, LOCALHOST)
    NAMES.TRACE_LEVEL = ADMIN
    My alert file
    <msg time='2013-10-10T20:47:02.687-04:00' org_id='oracle' comp_id='tnslsnr'
    type='UNKNOWN' level='16' host_id='ABIGAIL'
    host_addr='::1'>
    <txt>10-OCT-2013 20:47:01 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=__jdbc__)(USER=SYSTEM))(SERVICE_NAME=orcl.0.0.10)) * (ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=38289)) * establish * orcl.0.0.10 * 12518
    </txt>
    </msg>
    <msg time='2013-10-10T20:47:02.687-04:00' org_id='oracle' comp_id='tnslsnr'
    type='UNKNOWN' level='16' host_id='ABIGAIL'
    host_addr='::1'>
    <txt>TNS-12518: TNS:listener could not hand off client connection
    TNS-12560: TNS:protocol adapter error
    </txt>
    </msg>
    My listener status and services
    LSNRCTL> status
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1521)))
    STATUS of the LISTENER
    Alias                     LISTENER
    Version                   TNSLSNR for 32-bit Windows: Version 11.2.0.1.0 - Produ
    ction
    Start Date                10-OCT-2013 22:47:58
    Uptime                    0 days 0 hr. 2 min. 1 sec
    Trace Level               off
    Security                  ON: Local OS Authentication
    SNMP                      OFF
    Listener Parameter File   E:\app\abigail\product\11.2.0\dbhome_1\network\admin\l
    istener.ora
    Listener Log File         e:\app\abigail\diag\tnslsnr\ABIGAIL\listener\ale
    rt\log.xml
    Listening Endpoints Summary...
      (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1521ipc)))
      (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=ABIGAIL)(PORT=1521)))
    Services Summary...
    Service "CLRExtProc" has 1 instance(s).
      Instance "CLRExtProc", status UNKNOWN, has 1 handler(s) for this service...
    Service "orcl.0.0.10" has 1 instance(s).
      Instance "orcl", status READY, has 8 handler(s) for this service...
    The command completed successfully
    LSNRCTL> services
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1521)))
    Services Summary...
    Service "CLRExtProc" has 1 instance(s).
      Instance "CLRExtProc", status UNKNOWN, has 1 handler(s) for this service...
        Handler(s):
          "DEDICATED" established:0 refused:0
             LOCAL SERVER
    Service "orcl.0.0.10" has 1 instance(s).
      Instance "orcl", status READY, has 8 handler(s) for this service...
        Handler(s):
          "D006" established:0 refused:0 current:0 max:800 state:ready
             DISPATCHER <machine: ABIGAIL, pid: 1312>
             (ADDRESS=(PROTOCOL=tcps)(HOST=ABIGAIL)(PORT=1060))
          "D005" established:0 refused:12 current:0 max:800 state:ready
             DISPATCHER <machine: ABIGAIL, pid: 1288>
             (ADDRESS=(PROTOCOL=tcps)(HOST=ABIGAIL)(PORT=1061))
          "D004" established:0 refused:1 current:1 max:16383 state:ready
             DISPATCHER <machine: ABIGAIL, pid: 1260>
             (ADDRESS=(PROTOCOL=tcp)(HOST=ABIGAIL)(PORT=1063))
          "D003" established:0 refused:1 current:1 max:16383 state:ready
             DISPATCHER <machine: ABIGAIL, pid: 1140>
             (ADDRESS=(PROTOCOL=tcp)(HOST=ABIGAIL)(PORT=1062))
          "D002" established:0 refused:1 current:1 max:16383 state:ready
             DISPATCHER <machine: ABIGAIL, pid: 140>
             (ADDRESS=(PROTOCOL=tcp)(HOST=ABIGAIL)(PORT=1059))
          "D001" established:0 refused:1 current:1 max:16383 state:ready
             DISPATCHER <machine: ABIGAIL, pid: 1072>
             (ADDRESS=(PROTOCOL=tcp)(HOST=ABIGAIL)(PORT=1057))
          "D000" established:0 refused:1 current:1 max:16383 state:ready
             DISPATCHER <machine: ABIGAIL, pid: 748>
             (ADDRESS=(PROTOCOL=tcp)(HOST=ABIGAIL)(PORT=1058))
          "DEDICATED" established:0 refused:0 state:ready
             LOCAL SERVER
    The command completed successfully

    I added this on my listener.ora
    DIRECT_HANDOFF_TTC_LISTENER=OFF
    Works now!
    Moral of the story, google is ur friend lol. Thanks for the reply tho!

Maybe you are looking for

  • Sales order item gets "Fully delivered" status even if partial qty

    Hello, We have a depot sales configuration in SAP. I found that some sales order lines are getting completed (delivery status "Fully delivered") even if partial quantity is pending for the order line. I checked the status in VBUP table where LFSTA ge

  • Want to sync iphone to my itunes account that I use with my ipod

    I have recently purchased an iphone 4S and when i switched it on for the first time it came up with a set-up screen.  One of the options was to set it up as a new iphone (new apple ID and password) or to restore from an itunes back-up.  I would like

  • Authorization object  assigning to user profile

    Hi all,   Wht are the steps involved in assigning authorization object S_GUI with activity 60 (S_GUI ACTVT=60) to the users profile. Thanks

  • What are the iBooks Author hard/software requirements

    My wife is an author of some midlevel fantasy books that are doing well in paperback and eBook so she wants to get them on iBooks but to do so I need to get a Mac for her; I was going to pick up a used Mac but cannot find any info on the hardware req

  • Stuck... Pease need help passing variable

    Hi all.... I have an event listener added and it calls a function. Adding the event listener passes the event to the function automatically but what if i want to pass additional information to it? So this: addEventListener(Event.ENTER_FRAME, doEveryF