Windows 7 and Wireless Guest Access

Dear All, one of my Customers uses 4400 based Guest Access Solution with L3 Webauth. With XP everything works Fine. Since the Migration to Windows 7, Guest Access is not working correctly. It takes a long time to get an IP Address via DHCP, sometimes it idles to 169.xxx. If an IP Address is provided, the Redirect will not work. Has anybody seen similar Problems with Win7 or a Solution?
Regards, Michael

Found a solution for the "Boot Camp x64 is unsupported on this computer model" message. Here is the link: http://www.techulous.com/hardware/how-to-apple-boot-camp-64-bit-for-windows-7-on -unsupported-macs.html
Everything works ( for ) now. Yay!

Similar Messages

Wireless guest access with CWA and ISE using mobility anchor

My team is trying to demo wireless guest access using CWA with an ISE server. We appear to be hitting an issue when combining this with mobility anchoring.
When we don't use a mobility anchor the authentication goes off without a hitch seemingly proving that the ISE configuration is sound. The test laptop associates and gets redirected, auths, moves to the RUN state and access to the network is granted.
When the mobility anchor is enabled, the test laptop does get redirected, authentication is successful, but the process does not fully complete, as on the foreign controller the user is in RUN state whereas on the anchor the user is still stuck at CWA required.
Now, I've read the L2 auth occurs between the foreign controller and ISE, and the L3 auth occurs between the anchor controller and ISE, but this does not appear to borne out in packet captures of the process where both parts of the auth seems to go to and from the foreign controller and ISE.
I'm curious to know if anyone else has come across this issue, or has ideas where I should be looking in the config or debugs to find the root cause.
When setting up the controllers and ISE this guide (linked below) was used and the controllers are 2504 controllers on 7.5 series software and ISE is on the latest 1.2 patches:
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml
To me it seems to be mobility related, but the authentication flow does seem to be off compared with what the guide says.

FOREIGN
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Adding mobile on LWAPP AP 0c:d9:96:ba:7d:20(1)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Association received from mobile on BSSID 0c:d9:96:ba:7d:2f
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4565 setting Central switched to TRUE
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4568 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying site-specific Local Bridging override for station 00:1e:c2:c0:96:05 - vapId 1, site 'AP-Group-CHEC.default', interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying Local Bridging Interface Policy for station 00:1e:c2:c0:96:05 - vlan 84, interface id 0, interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfProcessAssocReq (apf_80211.c:7830) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Idle to AAA Pending
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 20) in 10 seconds
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created for mobile, length = 253
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created in mscb for mobile, length = 253
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Redirect URL received for client from RADIUS. Client will be moved to WebAuth_Reqd state to facilitate redirection. Skip web-auth Flag = 0
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 255 to 255
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 84
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 0 on mobile
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Initializing policy
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state AUTHCHECK (2)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=ExpForeign, client state=APF_MS_STATE_ASSOCIATED
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 apfMsRunStateInc
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) Change state to RUN (20) last state DHCP_REQD (7)
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Reached PLUMBFASTPATH: from line 5793
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Adding Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID = 255,
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*mmMaListen: Jan 28 23:05:02.363: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 0.0.0.0 plumbing in FP SCB
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP processing DHCP REQUEST (3)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 5, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   requested ip: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP received op BOOTREPLY (2) (len 320,vlan 84, port 13, encap 0xec07)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP processing DHCP ACK (5)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 0, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0, yiaddr: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   siaddr: 10.30.4.173, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   server id: 1.1.1.2 rcvd server id: 1.1.1.2
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) DHCP Address Re-established
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Reached PLUMBFASTPATH: from line 6978
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 Assigning Address 10.130.98.8 to mobile
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP successfully bridged packet to STA
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:03.890: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 10.130.98.8 plumbing in FP SCB
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 0 to 255
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 AAA redirect is NULL. Skipping Web-auth for Radius NAC enabled WLAN.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Applying cached RADIUS Override values for mobile 00:1e:c2:c0:96:05 (caller pem_api.c:2307)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Applied RADIUS override policy
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Change state to RUN (20) last state RUN (20)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 3600, apfMsTimeOut '1800' and sessionTimerRunning flag is 1
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 3600 seconds
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 3600
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4

Wireless Guest Access with 802.1X (PEAP/MSCHAPv2) and ISE?

Hi,
I have a setup based on WLC 5508, Catalyst 3750-X and AP3600i.
The WLCs are running 7.3 and ISE is 1.1.1
I'm trying to setup wireless guest access, where the guests connect to a SSID with 802.1X using PEAP/MSCHAPv2.
They should receive their username/password either from a sponsor directly (corporate AD user which prints the credentials) or through a SMS.
The credentials will be created by the sponsor, using the sponsor portal on the ISE.
Now to the questions:
Is it correct that the foreign WLC (i.e. the WLC within the internal corporate network), should be set to no L2 and L3 security on the guest WLAN, to avoid having the foreign WLC contact the ISE and all traffic be forwarded directly to the anchor WLC?
Is it correct that the anchor WLC (i.e. the WLC in the DMZ), should be configured with 802.1X/WPA2 L2 security and the ISE servers as the RADIUS servers on the guest WLAN, to ensure that the client is correctly authenticated/authorized by the ISE?
When a guest logs on, how can I ensure that only one device (MAC address) is allowed per user?
As it is now, a guest is able to log on with (I assume) an unlimited number of devices, using the credentials they have received.
Thankyou very much :-)
Best Regards,
Niels J. Larsen

Hi,
I have a setup based on WLC 5508, Catalyst 3750-X and AP3600i.
The WLCs are running 7.3 and ISE is 1.1.1
I'm trying to setup wireless guest access, where the guests connect to a SSID with 802.1X using PEAP/MSCHAPv2.
They should receive their username/password either from a sponsor directly (corporate AD user which prints the credentials) or through a SMS.
The credentials will be created by the sponsor, using the sponsor portal on the ISE.
Now to the questions:
Is it correct that the foreign WLC (i.e. the WLC within the internal corporate network), should be set to no L2 and L3 security on the guest WLAN, to avoid having the foreign WLC contact the ISE and all traffic be forwarded directly to the anchor WLC?
Is it correct that the anchor WLC (i.e. the WLC in the DMZ), should be configured with 802.1X/WPA2 L2 security and the ISE servers as the RADIUS servers on the guest WLAN, to ensure that the client is correctly authenticated/authorized by the ISE?
When a guest logs on, how can I ensure that only one device (MAC address) is allowed per user?
As it is now, a guest is able to log on with (I assume) an unlimited number of devices, using the credentials they have received.
Thankyou very much :-)
Best Regards,
Niels J. Larsen

E4200 Wireless Guest Access issue

Hello, I'm hoping someone can point me in the right direction. I have the wireless guest access set up in my E4200 flash to the latest firmware.
When I connect to the wireless guest network it comes up under the 192.168.33.xx IP address. I can connect fine but it never pops up the browser so that you can type in the guest password. I'm running Windows 7 but I've also noticed the exact same problem under XP.
The only thing I can guess is the problem is that I have this acting like an access point and all DHCP requests go to my router. I've basically turned off DHCP on this and plugged the network connection into the switch on the back.
Any suggestions?
Thanks
Josh

If I go to 192.168.33.1 it does pop up the browser but when I enter the password It just hangs. Not sure if it was connected or not. Is there no way to pop up the browser automatically?

Wireless guest access

Hi Guys, I have a wireless requirement from a customer and the customer is looking for the below: 1. Wireless guest access that requires user to input email into the captive portal. But the email address must be verified that it contains certain selected domain names (e.g. example.com or example.org). Any other domain names will be rejected. 2. Customer is looking to add their own logo and change the formatting of the captive portal. Questions: 1. For email verification, does this feature come straight from the WLC standalone box or must ISE be purchased? 2. If the WLC is able to do this without ISE, any online guides that is able to do this? 3. For security reasons, am I able to limit the number of concurrent users using this captive portal? 4. How do a configure the age-out for each connected users after they have successfully logged into the captive portal? 5. Can I customize the captive portal page on the WLC and how do I go about doing it?

Hi Mohanak,
It looks like the formatting ran out. Anyway, not sure if we are on the right topic here but let me get this straight. Customer has a Cisco 2504 Wireless LAN Controller. So, they would like to achieve the below features:
1. Wireless guest access that requires user to input email into the captive portal. But the email address must be verified that it contains certain selected domain names (e.g. example.com or example.org). Any other domain names will be rejected.
2. Customer is looking to add their own logo and change the formatting of the captive portal.
So, some of the questions I have are:
Questions:
1. There is a configuration on the WLC that allows guest users to login using email verification only. Does this feature come straight from the WLC standalone box or must ISE be purchased.
2. If the WLC is able to do this without ISE, is the WLC able to check if the inputted field is a valid email? And can I configure in such a way a particular domain is allowed? (e.g. example.com is permitted but example.org and anything else is reject).
3. For security reasons, am I able to limit the number of concurrent users using this captive portal?
4. How do a configure the age-out for each connected users after they have successfully logged into the captive portal?
5. Can I customize the captive portal page on the WLC and how do I go about doing it?

1801W wireless (guest access) config issues

Trying to setup wireless on 1801w ISR. Wired access to Internet and LAN works fine (Vlan1); however, wireless (Vlan2) does not.
Trying to setup wireless "guest" access with Internet access only (no access to LAN).
Wireless will not come up. Dot11Radios show "reset/down".
Below is the wireless config and a couple of troubleshooting commands as well:
dot11 ssid open
   vlan 2
   authentication open
====================================================
!(Sets up DHCP and excluded addresses.)
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 172.16.25.1 172.16.25.99
ip dhcp excluded-address 172.16.25.116 172.16.25.255
ip dhcp pool open
   import all
   network 172.16.25.0 255.255.255.0
   default-router 172.16.25.1
   dns-server 4.2.2.1 4.2.2.1
   lease 3
====================================================
(Turned on integrated routing and bridging.)
bridge irb
====================================================
(Wireless radio interface config.)
interface Dot11Radio0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip virtual-reassembly
ip route-cache flow
encryption vlan 2 mode wep optional
!---(SSID is given as "open")
ssid open
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Vlan1
description LAN
ip address 192.168.0.100 255.255.255.0
ip nat inside
ip virtual-reassembly
interface Vlan2
description Wireless VLAN
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 172.16.25.1 255.255.255.0
ip nat inside
ip virtual-reassembly
bridge 1 protocol ieee
bridge 1 route ip
====================================================
Verifying...
RTR#sho dot11 associations
802.11 Client Stations on Dot11Radio1:
802.11 Client Stations on Dot11Radio0:
SSID [open] : DISABLED, not associated with a configured VLAN
====================================================
RTR#sho ip int brief
Dot11Radio0                unassigned      YES NVRAM reset                 down
Dot11Radio0.1             unassigned      YES unset reset                 down
Dot11Radio1                unassigned      YES NVRAM reset                 down

Your ssid is configured in vlan 2.
But you forgot to configure dot11radio0.2 with under it "encapsulation dot1q 2".
That should allow the radio to broadcast ssid
Nicolas
===
Don't forget to rate answers that you find useful

Unified wireless guest access

Hi I need help in configuring unified wireless guest access. i have followed the guide
http://www.cisco.com/en/US/docs/solutions/Enterprise/Mobility/emob41dg/ch10GuAc.html#wp999843.
But the problem is it still does not work. what i dont get is that the interface for the Guest SSID for the foreign controller is management, does this mean that i have to get an IP address first from the management segment before i can get an IP from the anchor WLC?
my setup is that i have an anchor controller which is on a different LAN from where my foreign WLC is. the anchor WLC has the DHCP scope and the local net user database. I have already join the two WLC to each other's mobility group. also i have configured the mobility anchor on the WLAN(SSID) of the foreign controller.
Another thing is that the AP im trying to use is on a different site from where my controller is. Im not sure if this is the one causing problem.
Can someone help point out my mistake.

Its rare that I have a difference in opinion from both of you guys but let me share with you an issue I had.
If you map the foreign controller to the management interface and the tunnel breaks for whatever reason the clients will get dumped on the management interface, even though the WLAN is anchored to the DMZ controller.
I know this becuase I seen this for my self when I had anchor issues.
I opened a tac case and it was suggested to use a "dummy interface" on the foreign controller. I forget who I spoke to, this is over a year now. But I then followed up witha Cisco SE on the Advance Wireless team and he commented this is what they do as well. And to add further, a large hospital system here in the Tex Med center had Cisco advance team install their controllers and they too had dummy interfaces for the foreign controllers for guest.
Just my 2 cents ... Add a dummy interface call he dummy_guest_interface and tie it to 222.222.222.222 or something like ... no need to add anything on the wired.

Does WAP4410N support Wireless Guest access solution?

Does the Linksys AP (WAP4410N) support Wireless Guest access solution?

Hi - I've got a WAP4410N which I'd like to use to provide wireless guest access, and I've had a look through the configuration pages and manual, and understand:
1) I've got to add a virtual SSID (although I'd like to know where the DHCP settings are as I don't believe the WAP4410N has DHCP capabilities)
2) I need to ensure that traffic can't hop across the multiple SSIDs
What I'd like to know is whether the WAP4410N can be set up to display a terms and conditions page which users have to "OK" or whether it can host a login page that can be administered by someone to allow access - kind of like hotels use to ensure that not everyone can automatically connect? I don't mind if there has to be a secondary piece of software hosted on a server someone, but I'd like to prevent people from being able to automatically connect straight to our connection and would also like to limit them in some way, at very least the bandwidth that the connection allows, at best the sites they can visit too.
Any thoughts greatly appreciated,
Andy

SA 540 and DMZ Issue for Wireless Guest Access

I have hooked up a Wireless AP into the Optional Port setup as DMZ on the SA 540. My goal is to provide internet access to wireless guest users without giving them access to the entire LAN. The internet access for the wireless guest users is painfully slow. It takes 5 minutes to access Google. Has anybody else had issues with slowness. I am able to successfully ping websites and retrieve their IP address, but it won't connect to any websites via web browsers. Just to humor myself, I configured firewall rules to allow DMZ full access to the LAN and WAN. I am still having the same results. Any thoughts and suggestions?

Hi,
I'm not the one with the AP problem, I just have the same issue with the DMZ port. I think you have to forget about the whole AP issue here since the problem is with the DMZ port on the SA500.
I have my Web and Mail server set up on the DMZ port, I can ping and resolve Domain names to the outside world, but trying to reach anything with a browser takes foreeever. On, eg. www.apple.com I just get a few lines from their web page (so there is a connection) and then it halts to a stop (takes about 5 min).
I also tried to move my laptop to the DMZ, just to make sure there is no problem with the server, and it has the same issue.
To summarize, I have about 16 Mb connection on my LAN and on my DMZ i can't even load a full web page.
Firmware 1.0.39
BTW, when I upgraded the firmware it wiped my configuration, but it kept my firewall rules in place, even though they weren't shown in the Firewall table. e.g. I could still access my DMZ from my LAN. I had to hard reset the router from the hardware reset button on the router before that changed and the router was completely reset.

2106 and Wired Guest Access

Hi,
It seems that the 2100 models do not support wired guest access. I wondered if the following work around might work?
We are using a 2106 with a wireless guest network anchored to a 5508.
Would it be possible to configure an Autonomous AP in WGB mode and configure it to connect to the visitor wlan?
Would wired clients then be able to connect through the autonmous AP and use web authentication?
Cheers

I opened a TAC with Cisco.
Here was the repsonse.
Unfortunately this is not a supported feature , please have a look at the following
· These lightweight features are supported for use with a workgroup bridge:
– Guest N+1 redundancy
– Local EAP
· These lightweight features are not supported for use with a workgroup bridge:
– Cisco Centralized Key Management (CCKM)
– Hybrid REAP
– Idle timeout
– Web authentication
Note If a workgroup bridge associates to a web-authentication WLAN, the workgroup bridge is added to the exclusion list, and all of the workgroup bridge wired clients are deleted.
So it is not possible. Just thought I'd share this in case anyone else came across the same issue.

Windows 7 vs Guest Access

Hi All,
We have the Guest Access facility running on the CUWN and are starting to get reports of difficulties from a couple of Windows 7 users. One has an occassional problem with redirection to the web authentication page but a new one today just will not redirect. We're running WCS and WLC 7.0.
Has anyone else had this problem or know how to resolve it? If you need more details please let me know.
Thanks,
Scott

Hi,
turns out it was their endpoint compliance client stopping the redirection.
Scott

Relocating and wireless internet accessibility

I'm relocating and I'm wondering how I can find out if I have wireless internet access there and if I can keep my Fios or if I'll have to switch to another provider.
Thanks.

You may want to post this on the Residential side of the forum as this is for the cellular phone side.
At the top of this screen is a tab RESIDENTIAL. Click there and you can set up an account on that side and ask your question.

ISE with CWA and wired guest access via WLC Anchor

Can an Anchor WLC (WLCa) provide a wired guest LAN service if the wlan guest access is using CWA?
We are deploying a WLAN only ISE solution (it is a full license ISE though) but they just want a few wired guest ports. I was hoping to add L2 switch to the DMZ where the WLCa is and that the L2 switch wouldnt need any other config as the WLCa just bridges the wired to the wlan vlan. This Im sure i have done before.
So now I have set wiredguest the same as i have done before ISE and my wired clients get an IP address, but when they redirect, the URL they get is different, and the redirect just doesnt work.
It comes out as:
https://my_ise_ip:8443/guestportal/Login.action?switch_url=https://my_ise_host/login.html&wlan=my_wired_guest_lan&redirect=www.google.co.uk
So does my simple L2 only switch need an ISE config on it or should the WLCa be handling or the redirection just as it would for a wlan device.

The ISE never receives an auth entry, so i dont believe the redirect is working for the wired client. So even though the clients browser gets a redirect url which fails connection, the client info in the WLCa doesnt have a redirect ACL listed like a wlan client would

WLC and ISE guest access COA

We are migrating to ISE for guest access and are having problems with the COA being delivered after a successful authentication. ISE attempts to send it but nothing changes on the WLC. The message in ISE is Dynamic Authorization failed and a message that ISE didn't receive a response from the NAD, verify communication. What is odd is the original guest request comes in from the IP address of the service port on the WLC but anything doing with the COA is seen from the management. I have both IP's defined for the device in ISE. I am about to do a session reauthentication within ISE and the WLC applies the changes. I have verified that RFC 3576 is enabled, but the show radius rfc3576 stats shows no values. The WLC is running 7.6.130. I have attempted to debug on the WLC side to see if the message is even being delivered but non the debugs i have attempted seem to offer any good information.
Anyone have any suggestions?
Thanks,
Joe

Hi Joe,
I dont really know what you are trying to do with the COA , as it is used in the CWA solution and BYOD solution as well. But even before trying that , I would advise you to go step by step and solve the n/w issue first. You are able to see the request from service port which should not happen because then the incoming/outgoing traffic takes different path. You must be facing this situation as you might have some network routes matching ISE subnet/Ip address in the GUI>Controller>Network routes as there is no need of those routes. If the service port needs to be used during controller down scenario then use a laptop in the same subnet of Service port ip and connect to the service port.
Regards
Dhiresh
**Please rate helpful posts**

Wlc 5508 and wireless guest vlan

Hi guys,
I have a 5508 running(version 6).
I have an adsl releasing public IP for guest users mapped into vlan 10.
Now i want use this adsl only for wireless guest users
how can i create an ssid and associate to vlan 10 without using ip address(dynamic interfaces requires an ip address,mask,defaul gateway,etcc..).
Thx in advance.

Hi,
the fact that you can't ping in the guest SSID is normal. That SSID blocks all traffic until you authenticated on the web page.
If your users are using a proxy to browse the web, all you need to do is to add an exception in the client browser for "1.1.1.1" if that is your virtual ip. So that the proxy doesn't get contacted when client is redirected for authentication.
The second step is to make WLC listen on the proxy port (often it's 8080 for example). Command is "config network web-auth-port" :
http://www.cisco.com/en/US/partner/docs/wireless/controller/6.0/command/reference/cli60.html#wp1728200
Hope this helps,
Nicolas

Windows 7 and Wireless Guest Access

Similar Messages

Maybe you are looking for