Windows 7 backup - recurring message after changing backup location

I backed up my Win7 Ult 64-bit pc using Windows backup to a location on my NAS ( \\NAS\Share Folder Old, say).
Then I:
- amended Windows backup to use a new location ( \\NAS\Share Folder New, say);
- ran Windows 7 backup successfully (I think) to \\NAS\Share Folder New; and
- deleted \\NAS\Share Folder Old.
Now, whenever I start my pc, I get a message that it cannot connect to \\NAS\Share Folder Old.
No other program ever referred to \\NAS\Share Folder Old, it is not mapped to from my pc and it no longer appears (so far as I can see) anywhere in Windows Backup.
Can anyone suggest how I prevent Windows looking for \\NAS\Share Folder Old?
Thanks,
Alex

Hi,
Can you give us the full error message?
Go to the following registry path:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\WindowsBackup\ScheduleParams\TargetDevice
Check the PresentableName value, confirm it is the new backup location.
Alex Zhao
TechNet Community Support

Similar Messages

IPad sync hangs after changing Network Locations

I have a problem where often after I change Network Locations, the next iPad sync will hang in Step 1 of 5 with the progress right under the "e" of Step.
I have let it sit there for hours and it never progresses. I try to eject the iPad, it will never eject it.
I have sort of a formula to recover from this.
* I have to just disconnect the USB cable from the Mac.
* I shut down iTunes.
* I reboot the computer.
* I try to power off the iPad by holding down both buttons.
* It will hang for ever with the little spinning thing going in the middle of the screen.
* I will hold down the both buttons again and it will finally power off the iPad.
* I boot the iPad again.
* I bring up iTunes on the Mac and connect the USB cable and let it try to sync.
* This will fail the first time on Step 5 of 5 with the message "iTunes could not back up the iPad "My's iPad" because an error occurred. OK.
* I click OK.
* I eject the iPad.
* I shutdown iTunes and bring it back up.
* I plug the iPad back in to the MacBook Pro.
Now the iPad will sync and continue to sync normally unless I change my network "Location". Once I change my Network Location there is some probability that iTunes and the iPad will get into this stuck condition.
I've looked at the main console logs and All Messages. I don't see anything obvious.
Is anyone else seeing this behavior?
Does anyone have some hints about how to debug this?
-- Ed

Hi,
Tap Settings / General / Reset / Reset Network Settings.
See if that helps...
Carolyn

Photosmart C8100 operating system Windows 7 - no error message - no changes

Paper comes out with folded upper right corner.
Happens about 99% of the time.
Using H/P paper - both ink jet paper and premium photo with same results
Have followed video directions provided by H/P - no change
Have cleaned inside as much as possible with compressed air and hand vac.
See no paper scraps in path. Rollers seem soft and clean.
Anyone seen anything like this?

I could not even get to that window, I was able to select repair or complete install but when I chose repair, a message came up saying I couldnt repair that version of windows. It is the same disk I used for installation and it is in perfect condition.
Original HD configuration that was working was:
Slot 1 - original apple 250gb hd with System OS X 10.6.8
Slot 2 - 1tb hd formatted for OSX for storage
Slot 3 - 1tb hd with System Windows XP SP3
Slot 4 - 1tb hd with System Windows 7 64bit
HD configuration when that I changed:
Slot 1 - original apple 250gb disk was copied over to Slot 3
Slot 2 - unchanged 1tb hd formatted for OS X storage
Slot 3 - erased hd, reformatted and copied files over from hd in slot 1 using Disk Utility
Slot 4 - unchanged, Windows 7 64bit Ultimate installed now not booting
I have tried swapping the Windows 7 hd to each hd slot and rebooting (a Mac Pro gets really heavy after doing that 3 times!). Using startup manager, the windows boot option is unavailable. I can still boot into OS X in each placement without issues. I can go to System Preferences>Startup Disk and can see the Windows 7 option and select it. However even if I restart the computer from Startup Disk with Windows 7 selected, it will go to a black screen and say enter CD.
In case this helps, I had to purchase an original Windows 7 64bit ultimate and then create a new bootable system disk to install on this computer. I tried system repair from both disks and it did not work.
Im beginning to think that reinstallation is unavoidable, but still hoping that I can find a solution first. The actual installation isnt the major issue, it shouldnt take more than an hour to reinstall and update the video drivers. Its the installation of the programs and having to redo all of the settings on the 4 major programs that I am using that will literally take days. Oh man, somebody must know the answer!!
Thanks again for the response, I truly appreciate the help

Window - No Disk error message after update to iTunes 7.1

I updated to iTunes 7.1. After turning on iTunes for the first time after the download, I get a box that says "Updating iTunes Library". During this process, I get the dreaded error message: "Windows - No Disk" I clicked on it a few times and it went away. Then it came back and no amount of clicking would make it go away. At this point, iTunes no longer responds. I have gone thru this process now about 5 times.
What is the fix?
Does Apple answer this issue anywhere or is it left to its customers to speculate about this stuff?
Thank you fellow consumers.
David
dell laptop Windows XP

Do you mean like it says Windows-No Disk in Drive, please insert a disk? That type of message?
Rachyl

BOMBOS interface "warning" message after changes saved in the BOM.

Hello,
We our client is facing an issue, regarding BOM change / Modification in CS02.
After any modifications saved in the BOM (transaction CS02), in SLG1 transaction system gives u201Cwarning messageu201D as given below.
1.     Entry already exists in the work list
For components, system is giving following message.
2. Item material PPA_FORM_NU001 (Material number) is not assigned to a specification
We found one note for this u2013 u201Csapnote_0000893616_BOMBOS_Specification not foundu201D, this note is already applied in the program by SAP at 2005.
Because of this note, program creates the message in SLG1.
We also found that, in the IMG customization >>>
Environment Health & Safety > Product Safety > Bill Of Material Transfer > Specify Environment parameter & condition for the parameter u201CBOMBOS_WL_DIALOGu201D parameter value is u201CXu201D. If we remove this value, then system gives error message in the SLG1.
We want to know,
1.     Why we have such entries in SLG1?
2.     What is the goal of this standard BOMBOS interface?
3.     What is the impact of this warning message in the process of the transaction?
4.     To solve this, is there any solution?
Please confirm us.
Thanks in advance.
Edited by: Hemant Baviskar on Apr 27, 2009 11:25 AM
Hello, Can any body help me on this?
Thanks

Hello,
To rectify this issue, please refer the SAP Note - sapnote_0000683420 and make the changes accordingly.
Thanks
Best Regards

Somewhat Frightening Message after Changing Modem / Router Hardware

Yesterday, I changed my DSL Modem/Router to be a DSL Modem only, and added a different router by using its WAN port.
This essentially shut off control of the original modem/router, and moved it to the new router.
Now, we have 4 computers connected via ethernet cables, and none on Wireless. All are turned off, except my partner's Windows XP machine, which, suddenly today has a new message at the bottom left of his Login Window:
(Red Button) "Turn off Bills Modem Mods"
Who/Where did this come from? My computer's name is "Bill Lastname" ...
All computers are set to use TCP/IP Using Automatic DCHP selection of local IP Address and other parameters.
Some kind of Hacker prank, or am I just having a little paranoia attack? All other computers are Macs running OS X.
Mac Plus, Performa 6116, PPC 8500 G4/450, 9500 G3/500, QS 2@1GHz Mac OS X (10.3.9)

Not being a Windows user, I didn't realize I had inadvertantly input "Bills Modem Mods" to create a new account on the HP ... testing the new modem/router setup ... so that's why it started to appear as an option at the bottom of his signin window ...
Silly me ... didn't remember doing this ... so it startled me to think someone was hacking my partners computer ...
PTSD and Halloween approaching ...
Mac Plus, Performa 6116, PPC 8500 G4/450, 9500 G3/500, QS 2@1GHz Mac OS X (10.3.9)

Keep getting "Failed to connect to server" message after changing out my old router to a new one. Cannot receive any new emails. How do I connect again?

What can I do to fix this?

Check the address of the router in your settings for Windows. It has probably changed. You might want to check the settings in the router itself as well.

Error message after changing 8460p motherboard

I replaced a new motherboard on hp Elitebook 8460p with serial number - czc1293lxq Product - yq321ec#abb and when powered on it gives this error massage before booting to windows
The following product information programmed into the system board is missing or invalid
SYSTEM BOARD(OOA)-
Product name
Product Serial Number
Product SKU
ENTER- continue startup

Hi:
You have to take the PC to an authorized HP service center (or call HP technical support as to where to take it) and have the BIOS "tattooed" with all the missing info such as the serial number.
There are no BIOS DMI tools available for customers to do this themselves.
Paul

HT4974 After changing the location, can i remove the old files on the previous location ?

I changed the service data storage location, but the old files still there. So can i completly remove the old location files?
Is consuming a large amount of space, right know my Library folder have mre than 500Gb .
Can i do anithing to about that?
Thanks !

1) If SL was the original OS installed on that computer, you can't install it on a different computer. The DVDs are tied to the original computer.
Technically, if they are tied to anything it would be the computer model, not the physical computer itself. That means you could use it to install OS X on any computer with which those discs are compatible as long as you did not install on more than one computer at a time. I know this is a tad nit-picky, but that's the way it happens to be. No intended offense. Just hoping to be helpful.

How to change file location path at run time in OWB 10g

Hello all,
We want to load several files with the same name but from different folders into a single table.
The information about the paths is stored in an oracle table.
Is there any best practice to achieve this?
Our approach is to loop on the number of sources and execute the mapping after changing the location path. We found how to make the loop, and have the apropriate OMB command to update the location path, but we are still looking for a way to call this OMB plus command in a process flow or a mapping. Any idea?
We also succeeded in loading the file from an unregistered location, which is necessary to be able to update the path, but I'm not sure this is really the best approach. Any advise?
Thanks in advance for your help!
best regards
Cedric.

Hi,
I can provide you with an idea on this, dont know if it will work or not.
Suppose, you need to load 5 files in different folder locations into a single table. Call the mapping 5 times in a process flow. If you log in to the database, and go the table all_directories in your target schema, you will find an entry for the actual path of the file you are trying to laod. I think if this path is updated before each run of the mapping, you can load all files into the target table. Only thing you have to do is call a procedure which will update this record in all_directories table with the different locations each time you want and then plug in this procedure before each call to the mapping in a process flow and see if it works or not?
Regards
-AP

How can I see my messages after restoring from backup?

I have 2.1gb of messages saved in my storage on my 4s but they're not in messages after restoring from backup.
How can I get all my messages back in my message app because I know they're their it's just a matter of getting them restored into the app.

When you restored your phone from an old backup, it wiped ALL data from your phone and replaced it with the data from that backup. It's like your phone went back in time.
Your data that was on the phone before you did the restore is now gone forever. There is no way to get these data back.

Do not seem to be able to backup iPad via iTunes on to my PC. Message after connecting is "iTunes was unable to load class information from Sync Services, Reconnect or try later" Have tried that but get the same result. Can anyone assist?

Do not seem to be able to backup iPad via iTunes on to my PC.
Message after connecting is "iTunes was unable to load class information from Sync Services, Reconnect or try later"
Have tried that but get the same result.
Remedies I've tried are:
wait and try again
reboot
reload iTunes
NB hp is a relatively new machine and has previously backed up quite happily.
Can anyone assist?

RHoodnkt-
Try rebooting the iPad. Hold down both the Home and Sleep buttons for several seconds until the Apple logo appears. Ignore the "Slide to power off" arrow. It takes a minute or two to restart.
Also be sure your iPad battery is not completely discharged.
Fred

Backed up files partially disappear after restore (Windows Server 2008 R2 - Windows Server Backup)

Dear all,
I am experiencing a problem with "Windows Server 2008 R2", using Windows Server Backup.
Here's my setup:
Server: RAID 5 Disk setup
Backup:
By using Windows Server Backup (within Windows Server 2008 R2), C: and D: were fully backed up, with "System State" and "Baremetal Recovery" options selected. Backup went okay without any errors.
Restore:
By using Windows Recovery Environment (booted from Windows Server DVD), C: and D: were fully restored to the original partitions with "System Recovery" option found within Windows RE (without re-formatting partitions during restore). Restore
went OK without any errors. Rebooted, and system has been running fine.
Problem:
After the restore, the system itself seems running OK; no BSOD, no crash, no visible errors.
However, our client insisted some files (around 6 to 7) which are related to the propriety software has "disappeared" right after System Recovery.
Question:
Since Windows Server Backup is using "Volume Shadow Copy" technology which enables "live backup" of the running system, is it possible that some files will disappear (=restore error) after
System Recovery?
I cannot really find any errors or warnings related to Windows Server Backup in the event log, through. No Windows-backup errors. No VSS errors, too.
Do anybody have experienced this kind of problem in the past? Any suggestion will be greatly appreciated.

Thank you for your reply, Ms. Mandy.
To make things clear, let me explain to you briefly:
1. The "missing data" was backed up with "full system backup".
2. After a system restore from the above backup image, as you mentioned, partitions has been overwritten with the partions' backup data in the Backup Data Set taken by Windows Server Backup. No error with backup. No error after restore, and reboot - system
has been running fine.
3. Although there was a report that the affected files(about 7 java exectables) were missing after the above restore operation, other aspect of system was running fine at the time of the report.
4. I have checked the original backup data set - and voila, there ARE files which seems to gone after restore.
5. When I used Windows Server Backup "on" Windows Server 2008 R2 normal environment (= NOT Recovery environment from DVD) and selectd ONLY these affected files to restore, these files could be RESTORED successfully, without any errors. SO... data
was property backed up.
> The recovery will overwrite the partitions so files created after the backup point will be missing.
I understand, and this is not the case this time, because the affected files are already present in the backup data set (= I have mounted the backup data as VHD, and I could clearly see them present in the mounted VHD file)
Plus, these files are completely restoreable via "selective file restore" in Windows Server Backup.
Things I want to know/confirm:
> The recovery will overwrite the partitions
If I understand this correctly, in case that the files in question are already present in the backup data set, these files SHOULD be restored after full system restore, right? (If these files could not be restored, Windows Server Backup SHOULD show some errors.)
What do you think, Ms. Mandy? :)
Jo

Windows 7 slow to boot after setting up windows backup to additional drive.

I have an issue with windows taking forever to boot after setting up Windows backup.
PC Setup:
2 Samsung SSD Mirrored for Hardware raid on (MOBO OS/Programs)
2 Seagate 4TB Mirrored for Hardware raid (Data storage)
1 Seagate 4tb HD used solely for Windows backup. (Have also tried with multiple other drives with same outcome.)
If I have all drives connected without setting up the Windows Backup, system will boot up in 37 seconds. As soon as I enable the backup to the additional drive, it kills the boot time. Brings boot time to over 2.5 mins. Brand new PC, clean
installation, no antivirus or any other software that could be slowing it down. If drive is just in PC as an extra drive there seems to be no issue, just as soon as I enable the Windows Backup to additional drive. Never noticed this issue on any other
PC

Log booting process (set it in F8 menu).
Regards
Milos

I installed an ancient version, photoshop element 2, on PC under Windows 7 after change of computer station and it is impossible to register modification made; error message: impossible because saturated disc ....what is not the case: many space on the di

I installed an ancient version, photoshop element 2, on PC under Windows 7 after change of computer station and it is impossible to register modification made; error message: impossible because saturated disc ....what is not the case: many space on the disc. How to repair this error please?

Hello
Thank you for your answer which is interesting because it is a disk of 2 TB... If I create a partition do you think it can solve my problem? I prefer this old version of Photoshop, very practical to use...

Windows 7 backup - recurring message after changing backup location

Similar Messages

Maybe you are looking for