Windows 7 freezes on Disk.Sys

Hello, I have a pc with Windows 7 RTM 64 bit that I got it off of MSDN. The OS was installed and had been running without any problems for several weeks. I recently installed some updates and after I rebooted my machine I found that I can no longer boot into Windows in regular, safe or repair mode. My pc just freezes after the "starting windows" screen without the animation starting. In safe mode, the pc freezes when it hits "disk.sys". I can't even use the installation CD to boot into repair mode.
I've tried taking out components, changing ram, unplugging all unnecessary devices. Nothing works. Anyone have any ideas? Everything worked perfectly until last night.
My pc specs:
Intel e5200
Asus p5n7a - bios is in Nvidia RAID mode. Changing to SATA does not fix anything.
HDMI out

Hi,
I noticed that you can't launch Safe mode and Startup Repair mode, even using the installation CD. Regarding the current situation, I would like to propose the following methods.
Method 1. If you own another available DVD drive, please connect it to the computer and boot using the installation CD. Then boot in WinRE to perform System Restore, if System Restore doesn't work, let't try to use DISM to revert pending actions.
1) Try using the DISM command to see what update is in a problem state:
dism.exe /image:d:\ /get-packages
2) Use the /cleanup-image switch with DISM to revert the pending actions:
dism.exe /image:d:\ /cleanup-image /revertpendingactions
3) Once this is complete, try starting the PC into Windows.
Method 2. You can also create a USB boot disk to launch WinRE and take the above troubleshooting steps.
Method 3. Unplug the hard disk and slave to another available computer, then run the following commands:
chkdsk /f
sfc /scannow
Plus: basicly before installing Windows Updates, Windows will automatically create a restore point on the hard disk. You properly can run System Restore to get the previous status of the hard disk on another computer.
Best Regards
Dale

Similar Messages

Satellite L300 - Disk.sys error on Windows start up

I got my recovery disk today inserted and after a couple of reboots I managed to to get the Advanced menu F8. I selected option for Safe Mode with command prompt. The window started to load various windows drivers etc. It has now stopped at the line of code with a please wait and has been like this for over 2hours.
Loaded: \windows\system32\drivers\disk.sys
I booted up in VGA mode same
I tried last known good configuration no joy.
what's left for me to do it is obvious that I have a bad driver how do I interrupt the command prompt and run chdisk or check for corrupt drivers etc.
If I have to reload the OS can this be downloaded from microsoft or is it chargeable.
If anyone has any new ideas I would be very grateful need to get this sorted.
thanks
Franco

Hi TwoLags,
as you can see from the paper trail I originally could not get into advanced mode the forum suggested I purchased a recovery disk . The disk now allows me to get into F8 and advanced mode if I choose safe mode it scrolls through all the drivers but halts at \windows\system32\drivers\disk.sys with a please wait message in the windows bar.
I have tried booting up in safe mode with cmd prompt same,last known good config dark screen?.
My question is what happens next am I looking at a complete OS reinstall which I don't have windows vista home premium edition 32 bit.
Surely there must be a way of intreput the safe mose cmd and run a disk check to repair any corrupted files etc.
cheers
Frank

Windows is freezing.

Hi, Windows is freezing on my boot camp setup.
It's not a blue screen, the screen just freezes and my only option is to hard reboot the machine.
Upon reboot, Windows does not have any crash dumps to report.
I already ran a RAM test using mdsched.exe and no memory errors were found.
I am running Windows 7 SP1 Enterprise x64, Boot Camp 3.2, on a MacBook 5,1 model with 4GB of RAM.
Does anyone have any suggestions on what to try next?
I'm about to install Win7 x86 just to see if it works better...
Thanks!

chdsk
drivers
20GB of free space for Windows
heat
boot from Windows DVD and do a system repair
Disable AppleHFS.sys and AppleMNT.sys - rename those files to "*.old" for now, buggy.
Start - run and use %TEMP% and delete all the files there
CCleaner - clear out all the temp files and registry repair
Your AV software. Switch to MS Security Essentials unless you feel 200% yours is solid.
disable services; startup items
uninstall programs
make a system backup image
see how much space is use for page file
disable hibernate
check your power options
Pick up a reference Windows 7 Admin Handbook for one.
Nothing wrong with 64-bit though why would you need Enterprise? work? encryption?

Can't install bootcamp on Macbook Pro (2007 17-Inch) disk.sys error

Hi, I have a problem with a 2007 Macbook Pro that refuses to boot the Windows 7 Installer. When booting the disk it stays at "Starting Windows" and if I boot into Safe mode it stays stuck at "Loading: disk.sys". I made the windows partition using bootcamp and im using a Windows 7 Home Premium (32-bits) retail disk.
Please help i need windows because i make youtube videos and i can't find any screen recorder similar to fraps.
Thanks.

The Boot Camp Help guides are located here: https://www.apple.com/support/bootcamp/
The Boot Camp Discussion Community is located here: https://discussions.apple.com/community/windows_software/boot_camp
From this page http://support.apple.com/kb/HT5634 in the help guides, your 2007 Macbook Pro does not support Windows 7.

Fan speed increases and windows 7 freeze on my Satellite A200

I am using Toshiba Satellite A200-24A (PSAE3E) from 3 years now. It came pre-installed with Vista. Last year i switched to Winows 7 Ultimate. Everything was fine.
4 months ago, i switched to Windows 7 Enterprise N. Hated to see no Windows Media Player in it. Now the problem is, during online video streaming (not always the case), my fan speed inceases, so do its sound, and my hard drive gets real busy. 10 seconds later, my window is freezed. Actually, its not responding due to excessive hard drive usage.
I read many articles over the internet, lots of toshiba users are facing the same problem when using Windows 7. But, i couldn't find any solution to it.
This problem started 3 months ago, then for sometimes, it stopped itself. now, it started again 3 weeks ago. If anyone can help me regarding this issue, i will me more than grateful.
Here are my specs:
Windows 7 Enterprise N. Service Pace 1
1.73 Dual core
Ram 3GB
Hard Disk partitions 75 GB + 75 GB

I presume CPU usage goes to 100% and result is freezing. Can you identify background process that can be responsible for this?
> I read many articles over the internet, lots of toshiba users are facing the same problem when using Windows 7. But, i couldn't find any solution to it.
Your opinion is too general. Lot of Toshiba users have a lot of different problems with Windows7. My notebook was also delivered with Vista and since one year I use Win7 32bit and everything works perfectly.
> This problem started 3 months ago...
This make the whole situation more complicated. What have you done 3 months ago? Have you changed some settings, installed some additional software that can be responsible for this?
Unfortunately it is not easy to help in this situation.

Echo disk /sys/power/state broken

Hello all
After recent update after long time my hibernate was broken
#echo disk > /sys/power/state
does black screen and standby of display later. But system block not turned off, e.g. fans are worked.
#echo mem > /sys/power/state
is working. Before update echo mem not worked right
#cat > /sys/power/state
freeze mem disk
Install old kernel not resolve the problem.
I try to do debugging hibernation with https://www.kernel.org/doc/Documentatio … ugging.txt
echo freezer > /sys/power/pm_test
echo disk > /sys/power/state
worked
but
echo devices > /sys/power/pm_test
echo disk > /sys/power/state
not worked
If the "devices" test fails, most likely there is a driver that cannot suspend
or resume its device
Who can broke hibernation process?
dom ~ # lsmod
Module Size Used by
md5 1933 0
nfsd 232504 11
auth_rpcgss 39358 1 nfsd
oid_registry 1951 1 auth_rpcgss
nfs_acl 1995 1 nfsd
ipt_MASQUERADE 1742 1
iptable_nat 2746 1
nf_conntrack_ipv4 7754 1
nf_defrag_ipv4 1015 1 nf_conntrack_ipv4
nf_nat_ipv4 3008 1 iptable_nat
nf_nat 12791 3 ipt_MASQUERADE,nf_nat_ipv4,iptable_nat
nf_conntrack 60457 5 ipt_MASQUERADE,nf_nat,nf_nat_ipv4,iptable_nat,nf_conntrack_ipv4
iptable_filter 1092 0
ip_tables 10130 2 iptable_filter,iptable_nat
x_tables 11418 3 ip_tables,ipt_MASQUERADE,iptable_filter
arc4 1628 2
rt2800usb 15925 0
rt2x00usb 7726 1 rt2800usb
rt2800lib 56572 1 rt2800usb
rt2x00lib 33544 3 rt2x00usb,rt2800lib,rt2800usb
powernow_k8 16256 0
mac80211 389892 3 rt2x00lib,rt2x00usb,rt2800lib
hid_generic 749 0
usbhid 36545 0
ppdev 5998 0
pcspkr 1487 0
cfg80211 337508 2 mac80211,rt2x00lib
hid 71463 2 hid_generic,usbhid
psmouse 85683 0
evdev 8208 8
serio_raw 3969 0
k8temp 2782 0
crc_ccitt 1095 1 rt2800lib
rfkill 12714 2 cfg80211
snd_intel8x0 23721 0
snd_ac97_codec 89336 1 snd_intel8x0
ac97_bus 906 1 snd_ac97_codec
snd_pcm 63876 2 snd_ac97_codec,snd_intel8x0
snd_page_alloc 5942 2 snd_intel8x0,snd_pcm
forcedeth 51894 0
snd_timer 14942 1 snd_pcm
shpchp 21973 0
snd 44566 4 snd_ac97_codec,snd_intel8x0,snd_timer,snd_pcm
i2c_nforce2 4975 0
soundcore 4386 1 snd
parport_pc 16611 0
parport 25369 2 ppdev,parport_pc
button 3685 0
mperf 959 0
processor 22169 1 powernow_k8
nfs 126852 0
lockd 65996 2 nfs,nfsd
sunrpc 188264 27 nfs,nfsd,auth_rpcgss,lockd,nfs_acl
fscache 41347 1 nfs
sd_mod 28311 8
ata_generic 2434 0
pata_acpi 2367 0
pata_amd 8102 0
sata_nv 17199 6
firewire_ohci 27430 0
firewire_core 44687 1 firewire_ohci
crc_itu_t 1095 1 firewire_core
libata 149201 4 pata_acpi,sata_nv,pata_amd,ata_generic
ohci_pci 3228 0
ohci_hcd 21553 1 ohci_pci
ehci_pci 3404 0
ehci_hcd 42788 1 ehci_pci
scsi_mod 108590 2 libata,sd_mod
usbcore 152939 7 rt2x00usb,ohci_hcd,ohci_pci,rt2800usb,ehci_hcd,ehci_pci,usbhid
usb_common 1399 1 usbcore
floppy 48486 0
ext4 425668 4
crc16 1091 1 ext4
mbcache 4290 1 ext4
jbd2 70221 1 ext4
reiserfs 221231 0
radeon 1119891 2
i2c_algo_bit 4583 1 radeon
drm_kms_helper 31934 1 radeon
ttm 47394 1 radeon
drm 191258 4 ttm,drm_kms_helper,radeon
agpgart 22047 2 drm,ttm
i2c_core 19967 5 drm,drm_kms_helper,i2c_algo_bit,radeon,i2c_nforce2

http://www.mjmwired.net/kernel/Document … states.txt

Hp dv7-6b20ep windows 7 freezes

HP Pavilion dv7-6b20ep Entertainment Notebook PC windows 7 freezes
i did the memory test that passed
disk test passed
run in test failed
the windows 7 freezes sometimes

Hi thanks for your response.. Yes I have done that.. I even bought back up disk from HP and just got them yesterday. I tried them without any success. I have went into the Bios and changed the order, that didn't help. When this first happened, I placed the back up disk in, turned the computer on and it did begin to load, but then it stopped. Now it won't even do that. The hard drive was replaced because the old one crashed. I have tried just about every thing I can think of. I can turn on my computer and it will allow me to use most of my programs. But I can't get on the web and I can't even reformat my hard drive or I would try that.
Jim

Windows 8 Freezes after last "Lenovo Settings Update" anytime the pointer goes to a corner

After the most recent "Lenovo Settings Update", my Windows 8 freezes for a few minutes (minimum of two) anytime the pointer hits one of the hot corners. The system also freezes for a couple of minutes or less when certain apps are started or the mouse clicks on certain apps. This is a repeatable error. I can restore the system to the setpoint previous to the "Lenovo Settings Update" and everything works fine. re-Install the update and the problem comes back. The system also freezes for 5-10 seconds when an e-mail message comes in and the notification appears. Also happens under other different circumstances but the worst is when the mouse pointer goes to any "Hot Corner". I can reset the system to the last restore point and have everything work fine but anytime I go to "Lenovo Settings", it forces the update which then creates this problem.
Has anyone else seen this issue? I have all the updates for Windows 8 and Lenovo installed including all new Bios updates that are published. The model is a Lenovo ThinkPad Edge S320u (otherwise known as the "Twist". The error is repeatable in all screen modes, tablet modes and multiple monitor modes.
For now I will go back to the latest restore point but would like to see the issue resolved.
Thanks.
Bob

I had the exact same issue with the same computer (Thinkpad Twist)! Am very happy to have come accross this page through a web search.
After installing some updates through Lenovo Update App (because of a message that critical updates are available on the Lenovo Support App from Startscreen), my whole system would freeze for about two minutes when moving the cursor over any corner. This is very troublesome not only because it effectively disables the Windows 8 "hot corners" (which I didn't use much anyway, preferring to launch the tasks thus accessible differently), but mostly because it is necessary at times to access the corners, notably to close any document, webpage or other instance of any program that was open in full screen (which usually all of my docs/programs are, considering the Twist's small screensize...).
Afer reading rbagnall's post I first tried uninstalling updates through the Lenovo Update center. But there, once installed, updates don't seem to be removable. Why Lenovo? You can look at the list of installed updates but not make any change. Now I have followed rbagnall's advice and restored my computer with a restore point, sufficiently far back, as I didn't know exactly which update caused this. It worked! Not exactly pleasant, because I had to reinstall some programs and change some settings again, but the problem got resolved.
I went further and tried to see which update causes this by installing them one by one and seeing when the problem appears. The culprit seems to be "Display Mode Orientation Update for Windows 8". One needs to install the "Lenovo Power Management Driver" with it (which is actually listed under optional updates, whereas the Display Mode update is shown as a critical one, but the former is selected automatically when the later is chosen, and one cannot unselect it, a message appears then that it is necessary for the other update). So it could be that one as well (haven't checked whether installing it without the Display Mode update creates the same problem). In any case, once these are installed, the problem appears.
I have now restored my PC again to the restore point, and haven't installed any Lenovo update, not even the other critical one, as I don't know what it's for (Critical patch to fix TVSU UTS issue - I haven't had this issue, and any web entries on this I found dated back to 2009). In the optional updates there is also a BIOS update, which I had installed previously, but I don't know what it's for either. If there is anything terribly useful in either (or other optional updates), please tell me.
For now I have uninstalled the Lenovo Support Startscreen App (which seems to be more annoying than helpful), and will refrain from updating any Lenovo drivers from now, which seems to do more harm than good (everything was working fine before the update)...

Top 2 workable way to Create Windows 7 Password Reset Disk in any condition

This article describes how to create and use a Windows 7 password reset disk for a computer before and after you forgot the password. You can use Windows 7 password reset CD to gain access to your computer.
Scenario 1: I dont forget the password yet.
Windows 7 has its own backup feature, and you can proactively create a Windows 7 password reset disk before you forget it. With it, you can easily reset your Windows 7 password and get right into your PC.
Follow the easy steps below to create a password reset disk to your own Windows 7 account. Heres how:
Note that this procedure requires one blank, formatted floppy disk.
1. Click on "Start"->"Control"->"User Accounts and Family Safety"->"User Accounts".
2. In the task pane, click "Create a password reset disk". The "Forgotten Password Wizard" appears.
3. Click "Next", and then choose the portable media drive.
4. Click "Next", and then enter your current password in the next box and click "Next".
5. Windows 7 begin to create the password reset disk on your chosen media. When the progress bar reaches 100% complete, click "Next" and then click "Finish".
6. Now you can remove your device and store the disk in a safe place. Once you forget the password in the future, you can take it out.
Follow the easy steps below to use a password reset disk to recover Windows 7 password. Heres how:
1. The created password disk can now be used during log-ins to reset the password. A reset password link appears on the account screen after an unsuccessful attempt to log in.
2. Click on "Rest Password", and the "Password Reset Wizard" dialog opens. Here you need to insert the reset disk to the PC.
3. Follow the wizard to type a new password twice to make sure you type the correct password. You are suggested to create a new password hint, so that you can remember the password with it if you forget it.
4. Windows switches to the Windows log-in screen again where you can use the new password to log in.
Scenario 2: I have already forgotten the password.
If you have already forgotten your Windows 7 password but dont have a password reset disk at hand, you can choose another way to reset the password.
Here is how to create Windows 7 password reset CD/USB:
1. This procedure needs a CD or USB flash drive. Insert your media device into another computer which can access to system as administrator.
2. Launch Windows 7 password reset disk software. On the main interface, choose "reset Windows local account password".
3. Choose your target device, and click "Burn" to start Windows 7 password reset disk creation.
Here is how to reset Windows 7 password:
1. With this Windows 7 Password Reset USB software, boot the computer that you want to reset the password for.
2. Under Windows PE, you enter the main interface of this software. Choose your Windows system, and select the user account you need to reset password.
3. Click "Reset", and then "Yes" & "OK" sequentially to finish removing Windows 7 password.
Quite easy, isn't it? After fully control system password reset, you will never worry about your bad memory
+Message was edited: link has been removed+

well, as to reset Windows 7 password on toshiba laptop, it is a good solution to take a Windows password recovery tool, like Windows Password Unlocker
+Message was edited: link has been removed+

I have a Windows 7 Pro OEM disk that can install either the 32 or 64 bit version. When using version 5.0.3 of Bootcamp, I keep getting the message that it is a 32 bit disk. Any ideas how to get it to recognize the 64 bit version?

I have a Windows 7 Pro OEM disk that can install either the 32 bit or 64 bit versions. When trying to setup a dual boot for my Mac Mini using Bootcamp version 5.0.3, I get the message that I have the 32 bit version of Windows. Any ideas on how I can get it to recognize the 64 bit version so that I can partition my "Mini"?

If by "OEM" you mean the disk came with another Win computer, it won't work. You need either a full retail verison or the "System Builders' Edition." I used the latter for my BC installation and it worked flawlessly and was marked as 64-bit--no mention of 32-bit.

Window detected a hard disk Problem on my Satellite L505-S5988

Hi,
I have a Toshiba Satellite L505-S5988 with window 7 Home Premium 09 Service pack 1. It is 2+ years old and my hard drive is Toshiba MK3263GSX 287GB. Lately, I got a window warning message as “ Windows detected a hard disk Problem. Back up your files immediately to prevent information loss, and then contact the computer manufacturer to determine if you need to repair or place the disk….. The following hard disks are reporting failure: Disk Name: TOSHIBA MK3263GSX Volume: C:\ “.
Since then, I have imaged my laptop and run malware/spyware softwares, and it looks like my computer is clean. The laptop device manager said my hard drive is working properly. However the warning keeps pops up. I opened Administrative Event Viewer and found the below warning:
“Log Name: System, Source: Disk, Event ID: 52.
The driver has detected that device \Device\Harddisk0\DR0 has predicted that it will fail. Immediately back up your data and replace your hard disk drive. A failure may be imminent.”
EventData
\Device\Harddisk0\DR0
0E00030001000000000000003400048002000000000000000000000000112
D000000000000000000000000
Besides this warning, there are also other errors and warnings back to years ago, such as AFS failed to load, print service… Despite all these errors and warnings, my laptop seems to be running OK. I was not prevented from doing anything that I usually do.
Questions:
Is there a tool I can run to verify that my hard drive is truly bad?
Can any tool further identify where?
Can it be repaired? Reformat? Or I have to replace with a new one?
What options I have if I have to replace with a new one?
What is average cost of it?
Any help will be highly appreciated.

Satellite L505-S5988
Event ID: 52 - Source: Disk
..the warning keeps pops up.
That's good enough for me. I would replace the disk.
You can verify it with the free trial of HD Tune.
-Jerry

Windows 7 on MacBook Pro Retina late 2013. Showing popup window as "Windows detected a hard disk problem"

I have installed Windows 7 64 bit version in my MacBook Pro Retina(13") late 2013 model . It was working fine from last 8 months but recently popup window showing as "Windows detected a hard disk problem" once login. Please check the following image.
I have contacted Apple Support team. They have tested the hard disk while booting from Mac OS and all the reports showing as hard disk is fine. Then I thought might be it was some virus and removed the Bootcamp partition and re-installed Windows 7 Operating System. But once updated Windows 7 with latest updates. This message showing again.
Would you please help me out to fix this issue. Anybody faced similar issue?

No I think that all drive are really on failure
I've boot with an ubuntu livecd and smartmontools see also the failure.
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate     0x001a   200   200   000    Old_age   Always       -       0
5 Reallocated_Sector_Ct   0x0033   100   100   000    Pre-fail Always       -       0
9 Power_On_Hours          0x0032   099   099   000    Old_age   Always       -       1872
12 Power_Cycle_Count       0x0032   099   099   000    Old_age   Always       -       762
169 Unknown_Attribute       0x0013   253   253   010    Pre-fail Always       -       4003597393408
173 Unknown_Attribute       0x0036   100   100   100    Old_age   Always   FAILING_NOW 12124890467160
174 Unknown_Attribute       0x0022   099   099   000    Old_age   Always       -       7469954
175 Program_Fail_Count_Chip 0x0022   099   099   000    Old_age   Always       -       4989854
192 Power-Off_Retract_Count 0x0012   099   099   000    Old_age   Always       -       31
194 Temperature_Celsius     0x0022   064   064   000    Old_age   Always       -       36 (Min/Max 11/75)
197 Current_Pending_Sector 0x0022   100   100   000    Old_age   Always       -       0
199 UDMA_CRC_Error_Count    0x001a   200   199   000    Old_age   Always       -       0
240 Unknown_SSD_Attribute   0x0022   100   100   000    Old_age   Always       -       0
When I use the Mac disk tools from the startup menu, it see also the problem.
Now the big question is : Why I've this type of issue with 2 MBA and 1 Macbook pro 15".
Their configurations are the same : windows 7 with truecrypt.
Maybe Windows drastically reduces the lifetime of the Apple SSD drive.
The 3 Mac are used for less than 6 month !!!!

How to install ASM on MS Windows XP with regular disk partitions

Hi,
I just want to try out the feature ASM on my pc.
OS => MS Windows XP sp2, two disk partitions.
First I have installed the 10.2 software and then created a database.
After this, I use DBCA to create the ASM.
I have to run localconfig. But I still cannot see my disks (partitions C and D) on the Configure Automatic Storage Management page.
What I have done wrong?
Greetz,
Max

Hi Max,
Howard Rogers has written a good article on how to do this. See http://www.dizwell.com/prod/node/33
Cheers,
Colin

I am unable to Install windows xp with recovery disks.

I have a Toshiba’s Satellite Pro S300-10J laptop Model#PSSB0E-02H00FDU. Some days back its operating system got corrupted. I have its recovery disks(windows Xp) and now I am trying to reinstall the windows by using recovery disks but unable to do so. Actually when I insert disk 1 it start installation process and then prompt for 2nd disk and when I insert 2nd disk it starts unpacking software image process. At the end it shows a pop up box with the following information.
Info:
                Done(Files:28339/28339 Folders: 2558/2558).
                Please remove the recovery medium!
                                                |OK|
As I remove the 2nd disk and press ok and then exit it goes shut down instead of rebooting. When I press power button to on it then it goes stuck on windows startup with a message of please wait .
Please support that how can I get rid of this situation and can restore operating system with recovery disk.

I made another attempt but nothing goes productive.
One thing is clear that the recovery disks are ok because a few months back I used same disks to refresh my notebook and did it without any error.
There might be a chance of bios setting because in my absence my sister and her friend tried to install windows and I doubt her friend made some changes in bios but she says that she didn’t made any change except boot priority and during installation got the error.
I have already rest the bios setting to default and in SATA CONTROLLER MODE I changed it from AHCI into IDE.
With recovery disks of XP Installation starts and after image loading it doesn’t restart just goes shut down and upon restarting just stop responding/hang up on startup.
I tried with another CD of XP and during installation when system restarts setup continues on ‘INSTALLING WINDOWS’ with the message that ‘Setup will complete in approximately 35 minutes ‘Installing devices’ and at this stage it hanged up. Finally it shows blue screen with an error like
Technical Information
STOP: 0X000000F4 (0X0000003,0X89936670,0X899367E4,0X805D1142)
Beginning dump of physical memory.
On several attempts the result remains same.
Need your valuable advice please..

Transfering files from Windows machine freezes my wi-fi connection

Guys, this is very weird, and it started to happen a week ago.
I use finder to connect to my windows machine on my home network, and after typing my password, I get access to the folder in the windows machine that I want.
The problem is: any file I try to transfer FROM or TO the windows PC freezes up mac os X after some seconds of transfer ... like a 60 mb file, it freezes after 20mb have been transfered ... and that's not only it ...
It freezes mac os x until I get the message "Connection to server LOST", and I only can get back on the network if I literally shut down my wi-fi router, because my macbook simply can't get DNS ip assigned again, it always auto-assign some weird ip and doesn't come back to the network till I restart my wi-fi router.
What in the **** may be going on ? Remember, it started to happen lately, it was not like this before !
Apple Macbook 13inch 2.0ghz Core Duo 512 60GB White SuperDrive Mac OS X (10.4.7)

Dear Customer
Welcome in lenovo community
Have you check the wirless device status from the PC setting , is the switch are dimmed ( Please share a screen shot ) also please check the driver if installed properly or not .
Please let us know
Thanks
Alaa
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Windows 7 freezes on Disk.Sys

Similar Messages

Maybe you are looking for