Windows 7 No sound after resume from sleep p-105

Toshiba p- 105 s6227: No sound after computer wakes from sleep. If I do a complete reboot it works again. I had a similar problem with Vista and ended up not using the HD drivers. The AC'97 drivers worked fine.
NOW: I've upgraded to WIndows 7 64-bit clean install(supported), used the Toshiba Utilitys and am having the same problem. The speaker green bar goes up an down like it thinks it is working. All device drivers say they are fine. Sound troubleshooter finds nothing.
Yes, my volume knob is turned on..... I downloaded and reinstalled the sound drivers, this resarts the sound, but it just cuts out again, after sleep.
Any suggestions or ideas... other than never putting computer in sleep mode?
Thanks in advance!
Gary

glmccready wrote:
Toshiba p- 105: No sound after computer wakes from sleep. If I do a complete reboot it works again. I had a similar problem with Vista and ended up not using the HD drivers. The AC'97 drivers worked fine.
NOW: I've upgraded to WIndows 7 64-bit and am having the same problem. The speaker green bar goes up an down like it thinks it is working. All device drivers say they are fine. Sound troubleshooter finds nothing.
Yes, my volume knob is turned on..... I downloaded and reinstalled the sound drivers, this resarts the sound, but it just cuts out again, after sleep.
Any suggestions or ideas... other than never putting computer in sleep mode?
Thanks in advance!
Gary
It's an acknowledged issue with A215 series laptops:
http://laptopforums.toshiba.com/t5/Windows-7/Satellite-A215-s5824-windows-7-Standby-Problems/m-p/670...
You may want to call Toshiba and let them know it's happening on P105s...

Similar Messages

Slow LAN Networking Speeds after Resuming from Sleep

I use my mac mini as a HTPC running Plex. I have it connected to my Windows media server with 802.11n. Works fine but sometimes after resuming from sleep the network speed drops off to an unacceptable level (from 72 Mb/sec to 5 Mb/sec). Disconnecting and reconnecting doesn't help. Switching to G doesn't help. Only restarting the mini restores the connection to full speed.
None of my Windows clients on the same network have any troubles.
Thoughts?

Looks like Plex might be causing the problem. I always have plex running and it appears as though if Plex makes a request for a file on the share before OS X is done re-mounting it after sleep, it kills the whole process.
Shouldn't the OS be robust enough to handle a situation like this?

Update to 10.6.8 - system hang (mouse issue) after resume from sleep

I am on older
MacBook Pro3.1
Intel Core 2 Duo
2.6GHz
Run on 10.6.8 almost flawelessly. Shortly after upgrade to 10.6.8 system started to hang periodically after resuming from sleep. Symptoms are that it stops responding to mouse (be it touch pad or USB mouse). Keyboard seems to be ok but system doesn't seem to be fully functional. I am able to ssh from the other computer and 'shutdown -r now' after reboot system seem to be ok until next resume from sleep. What interesting though is that this problem newer manifests then I am using external monitor.

Found problem. It was due to magic mouse that I left on. I carry this mouse in the laptop bag but rarely use it. Last time I used it (around the same time I install the update) I left it on in the bag. It was apparently disconnecting/connecting on its own and by some reason sometimes was breaking touch pad and other usb mouse connected to laptop, as soon as I switched magic mouse off broblem was fixed

My Mountain Lion mac crashes after resuming from sleep

Hello
My Mountain Lion mac crashes after resuming from sleep every time I use it
It happens every time the mac resumes from sleep and it started like a week ago
I remember installing the new updates for flash? and xquartz and nothing else.
I have also had microsoft word installed on my mac for about 1 weeks before this problem started so might be related to that
Please share with me any tips on how to fix this because I am really annoyed of losing stuff after each time my mac resumes from sleep

I have an iMac bought may -11, and it worked fine with Snow Leopard.
About a week ago I bought and installed Mountain Lion 10.8.2. Everything went fine, and all software worked ok. iPhoto had some problems, but after installing update the system prompted to do, it has worked ok.
The propblem occurs now and then, when computer is waked up from sleep. The Desktop occurs, but no software starts, not even System Tools untlil rebooting the computer. Of course, I can not reboot the computer from "Apple menu", but holding the power button down.
This is very embarassing! OsX Mountain Lion has turned out to be a very big disappointment. I installed id because of iCloud (i have a new iPad, too with iOs 6 installed).
Can anyone help me? Is there any other way to solve the problem than re-installing good old Snow Leopard?
I would not like to do that, I bought Mac because I was bored in re-installing and recovering!
Thank you

On my new iMac, mail has no sound after waking from sleep. If I select do not wake for network access in general preferences, the problem does not occur. Anyone have an idea on how to fix this?

On my new iMac, mail has no sound after waking from sleep. If I select do not wake for network access in general preferences, the problem does not occur. Anyone have an idea on how to fix this? Thanks --

Same here on an older iMac since Lion. Thanks for the uncheck wake for network access tip though, it doesn't do it either in that case, I will leave it that way.

X120E Touchpad inoperable after resuming from sleep

hello friends I'm a happy X120E user and a tech [pc's, mac's, lans, etc] - I do all sorts of tasks with my x120e and its been great. I recently "upgraded" my SSD so a fresh new install of Windows 7 was in order. After updating everything I have a problem I did not experience previously at all - not once in 3 years of use.
Upon resuming from sleep [and as far as I can remember this only occurs when resuming on battery], the touchpad/cursor is inoperable, frozen in the centered position, and I have found no way to 'wake' it. I finally have to shutdown/restart to get things functioning again. Keyboard works fine, but not touchpad or trackpoint [either/both].
maddeningly, its not consistent in this. sometimes it works, sometimes it does not.
I have seen the same issue with, and without, the supplied Lenovo Ultranav driver installed.
Question: in the X120E implementation, is the touchpad a PCI bus device or a USB device? I see no power plan options [i.e. "Advanced" >"Allow this device to wake the computer"] available via Device properties. There are no pointer/mouse/touchpad options whatsoever under Power Plan Settings.
Will Fn+F8 enable/disable the touchpad on this notebook? or,... should it?

No. Powering off and on again didn't work. My drive is a Seagate 750GB internal SATA drive in a Vantec NexStar-3 external enclosure. I don't think it is a driver issue. After the device removal error it won't mount on my PC or my Mac via FireWire or USB.
What I need to know is if there is some way to connect to the drive and make it mount with other software, using some kind of keystroke during startup, or maybe through terminal or something. I can't even try to repair the drive because it won't show up in disk utility.

Windows explorer + other windows applications crashing regularly at resume from sleep and hibernate

Good evening,
I have a Thinkpad W510 (4319-29G) running Windows 7 Pro 64bit. The system is loaded with the latest software and drives from Lenovo including BIOS 6NET74WW (1.34), upgrade was done Dec 7th (windows update performed Dec 15th).
The machine has
- 8Gb RAM
- nVidia Quadro FX880M, driver version is 8.17.12.5896, 7-9-2010 and video card BIOS is 70.16.5f.0.b
- dual harddrives,
- one Seagate Momentus XT 500Gb (ST95005620AS) FW rev SD23 in the main location with C: and some other partitions
- one Hitatchi 320 Gb (HTS723232L9SA60) FW rev FC4ZC50B in the bay.
- Intel Centrino Advanced-N 6200 AGN, driver version 13.3.0.24, 7-14-2010
- Intel 82577LM Gigabit Network Connection, driver version 11.5.10.1030, 7-22-2010
Recently I have experienced crashes of multiple windows components at resume from sleep and hibernate.
It seems to happen when swithing location (from work to home) and thus switching from docking station with wired network connection to no dock and wireless network connection (dont know if this has any bearing but anyway).
In the event viewer I typically have some 6-12 application errors logged. Sample output from event viewer is:
Log Name: Application
Source:Application Error
EventID:1000
Level:Error
Logged:2010-12-15 20:30:02
Task category100)
Keywords: Classic
Computer: xxxxxxx (my computername)
Then for each application the following detailed data is written in event viewer in the general tab:
#1
Faulting application name: rundll32.exe_nview64.dll, version: 6.1.7600.16385, time stamp: 0x4a5bc9e0
Faulting module name: nview64.dll, version: 6.14.10.13527, time stamp: 0x4c35752f
Exception code: 0xc0000005
Fault offset: 0x00000000000f0786
Faulting process id: 0x115c
Faulting application start time: 0x01cb9bd59882f1f6
Faulting application path: C:\Windows\system32\rundll32.exe
Faulting module path: C:\Program Files\NVIDIA Corporation\nView\nview64.dll
Report Id: b606b17d-0881-11e0-be39-00a0c6000000
#2
Faulting application name: taskhost.exe, version: 6.1.7600.16385, time stamp: 0x4a5bc3c1
Faulting module name: nview64.dll_unloaded, version: 0.0.0.0, time stamp: 0x4c35752f
Exception code: 0xc000041d
Fault offset: 0x00000001800bb350
Faulting process id: 0x10c0
Faulting application start time: 0x01cb9bd5694caebe
Faulting application path: C:\Windows\system32\taskhost.exe
Faulting module path: nview64.dll
Report Id: b6ae8cb2-0881-11e0-be39-00a0c6000000
#3
Faulting application name: sidebar.exe, version: 6.1.7600.16385, time stamp: 0x4a5bc9e1
Faulting module name: nview64.dll_unloaded, version: 0.0.0.0, time stamp: 0x4c35752f
Exception code: 0xc000041d
Fault offset: 0x00000001800bb350
Faulting process id: 0x6f0
Faulting application start time: 0x01cb9bd5986a397a
Faulting application path: C:\Program Files\Windows Sidebar\sidebar.exe
Faulting module path: nview64.dll
Report Id: b6bd0bd9-0881-11e0-be39-00a0c6000000
#4
Faulting application name: Explorer.EXE, version: 6.1.7600.16450, time stamp: 0x4aebab8d
Faulting module name: nview64.dll_unloaded, version: 0.0.0.0, time stamp: 0x4c35752f
Exception code: 0xc000041d
Fault offset: 0x0000000008c3b350
Faulting process id: 0x1210
Faulting application start time: 0x01cb9bd569d9ae8e
Faulting application path: C:\Windows\Explorer.EXE
Faulting module path: nview64.dll
Report Id: b6d21ac7-0881-11e0-be39-00a0c6000000
#5
Faulting application name: Dwm.exe, version: 6.1.7600.16385, time stamp: 0x4a5bc541
Faulting module name: nview64.dll_unloaded, version: 0.0.0.0, time stamp: 0x4c35752f
Exception code: 0xc000041d
Fault offset: 0x00000001800ba570
Faulting process id: 0x11c4
Faulting application start time: 0x01cb9bd569aa125c
Faulting application path: C:\Windows\system32\Dwm.exe
Faulting module path: nview64.dll
Report Id: b72bfbe8-0881-11e0-be39-00a0c6000000
#6
Faulting application name: rundll32.exe_PWMTR64V.DLL, version: 6.1.7600.16385, time stamp: 0x4a5bc9e0
Faulting module name: nview64.dll_unloaded, version: 0.0.0.0, time stamp: 0x4c35752f
Exception code: 0xc000041d
Fault offset: 0x00000001800bb350
Faulting process id: 0x1450
Faulting application start time: 0x01cb9bd59995023a
Faulting application path: C:\Windows\system32\rundll32.exe
Faulting module path: nview64.dll
Report Id: b7e4521b-0881-11e0-be39-00a0c6000000
It seems that a module "nview64.dll" is always the first application to crash. I suspect this has something with graphics to do.
I dont know if this event triggers the following crashes or if it is so that the display is initialized before the other programs.
After all crash diagnostic messages have been shown windows explorer restarts and also other applications restart but a lot of system tools in the system tray are gone so a cold start is needed to restore all tools again.
I really would appreciate any help and suggestions how to fix this really annoying issue.
Thanks, Anton

I had a similar issue, as soon as a described even a little bit of it to warrenty support they sent someone to swap the board
It seems thats the only fix, its been fine since

T440S OSD Brightness control failure after resume from Sleep

Hi,
I have owned a T440S since late 2013.
Relevant Details:
T440S
Model : 20AQCTO1WW
OS : Windows 7 professional (original installation by Lenovo)
Latest Drivers installed as of June 2014 - including HotKey and Power Management
HotKey ver : 8.30
Power Managment : 6.65.1
Since receiving this laptop, OSD birightness control has always failed to work, i.e. does not appear on the screen
when using the Fn+F5/F6 key combination nor does it control actual screen brightness AFTER FIRST resuming from sleep
mode.
Sequence of steps that demonstrates the above symptom:
1. OSD brightness works fine after reboot
2. Putting the machine to sleep (I do not use hibernate) for a duration longer than a few minutes
3. Open lid the first time, hit Fn to resume machine
4. Pressing Fn+F5/F6 key combo does not display the brightness slider nor does it control brightness
5. Closing the lid and opening it again, causes OSD brightness slider to flash brifely and is now fully functional
using Fn+F5/F6 keys
Your tech department should easily be able to re-create this issue on any stock T440S/Win7pro machine, as
I have seen others comment about this very issue across other T440/OS variants.
This very same behavior has been there since the beginning.
When is Lenovo going to FINALLY FIX IT ONCE AND FOR ALL?
Thx,
--Alon
Solved!
Go to Solution.

Try this hotfix:
https://support.microsoft.com/kb/2752407
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

Mac Os X Lion Crashes after resuming from Sleep

Hi Everybody, i'm experiencing an issue on my 13'' MBP Early 2011 (i5 processor, 4GB RAM, 750GB HD SATA). My MBP often got stuc after i resume from my monitor sleep. I'll explain it in a better way: After i resume from sleep, there's at first a black screen in which the mouse can move, after that the mouse becmes the classic loading wheel and it freezes copletely, remaining in this situation. I thought it was a screensaver compatibility issue, but the problem stand still after i uninstalled screensaver and deactivate the screensaver options. I think it's a problem with Lion with the HD, but i have no evidence of it. Can Anyone help?
Thank you in advance,
Daniele.

Whenever someone comes to me with crashing and freezing on waking up I look at 3 things and typically in this order:
(1) Hard drive - usually if it is the hard drive SMART has already given a warning if the drive is actually failing or running Disk Utility reveals problems - often problems that cannot be fixed. Also, when the crashes are related to the hard drive there may actuallly be nothing wrong with the drive and a simple erase and reinstall will fix it.
(2) Software issues - the old trick of creating a new account and logging into it to see if the problem is in your account or global helps. Looking in console to see if there's an error message logged just before the crash can be instructive - or not. Often the crash occurs before an error is logged. Sometimes reinstalling the OS is the solution - that's where having a FireWire hard drive is helpful. I can just boot with it and see if the computer still crashes on waking. If not I know to reinstall the OS.
(3) RAM - marginal and faulty RAM can be the culprit in many cases. The frustrating thing about RAM is that RAM tests seldom give false positives, if the test says you have bad RAM, you do. Unfortunately when the test reveals nothing wrong the RAM might still be defective, just not enough for the test to catch.
However, past history has led me to put RAM at the top of the list after an OS upgrade. Marginal RAM has been the culprit of many crash on wake problems with previous OS upgrades. I especially recall Leopard and Snow Leopard being affected - at the shop where I sometimes work we did a lot of RAM warranty replacements after those two upgrades. And here at the support forum we saw lots of people complaining of crash on wake problems coming back and saying, "Yep, got my RAM replaced and all is well." So if any of you are like me and upgraded your RAM, if you have the original RAM sitting around swap it in and see if the crashes stop.

Wifi Lost and Network Preferences Inaccessible after Resume from Sleep

Macbook Pro, shipped with Lion.
I've had a problem when Lion resumes from sleep of not being able to access any networks. Specifically, the wifi symbol in the menu bar shows the pulsating waves, when clicked it reports that it is searching for networks, however it doesn't find the standard wireless network it is normally connected to at home, nor can I choose any further options in that dropdown menu. Specifically, I cannot access Network Preferences, via any GUI based method (don't know enough CLI to know how).
Most alarming is that this has happened in a couple of different scenarios:
1) normally putting the laptop to sleep if 2 different users are logged in via fast user switching
2) if the computer shuts itself down from the sleep position because it has been unplugged for too long.
Restarting does revert everything back to normal, but I was hoping for a less drastic fix. Sorry to gripe, but I'm especially disappointed because I'm a mac newbie, and between this and other problems, have had to restart this mac due to spinning pinwheels of death and the like more in 2 months than I ever have a Sony Vaio Z running Windows 7. Kind of disappointing that Mac has the less stable operating system.

That's awkward. It may not be the Mac itself making it unstable, but yet programs on it making it unstable (lazy developers maybe). Although do remember that OS X Lion is fairly new, and a few bugs are still being ironed out.
First thing you should do is Repair permissions. Open up Disk Utility, Chose your disk on the Left and click on the Repair Permissions button. This can take about 20 minutes and fixes most problems.
Questions:
Have you installed any additonal system prefence panels?
Have you installed any programs that alter with WiFi?
Does your WiFi Access point have enough strength for where you are?
If you have installed addional system preferences then I suggest that you go to Finder, and in the top bar click on "Go" and navigate to "Go To Folder". In that box put this: "~/Library/PreferencePanes" (No quotes though - and remember the "~" ).
It'll take you to a folder, copy those into a safe location and remove the contents of that folder.
If you are an Administrator of your computer then do the same in "/Library/PreferencePanes".
Hope all goes well! Good luck!

Airport no longer works after resuming from sleep

I got a new MacIntel a month or so ago, and it has always done this, under 10.4.4 and now 10.5.5
When resuming from sleep, airport shows full strength for second, then the signal disappears. NOTHING in settings, reconnecting etc will get it to work again. (this is 'deep' sleep, not just the display turning off)
If you restart (restart not shut down), then when it comes back, airport is just gone - even the menu bar indicator. The computer now thinks it has no airport installed at all. No matter how many times you restart, there is no longer any airport.
If you shut down, wait a minute and restart, it works as normal.
Since airport is the only way I connect to the network, and I don't want to waste electricity, this is unacceptable and clearly a flaw.
I called tech support and they had me move airport to the top of the list, delete plists and other stuff, none of which made any difference. I'm thinking this is a low level system software fault, and I hope I don't have to take it back for a motherboard replacement.

I also have this problem, although, not very often.
I'm still running 10.4.4. This never happened with
prior versions. Rebooting is the only way to
correct the problem. Simply turning off Airport and
turning it back on does not help.
Thats interesting actually because I Never had any trouble on my G5 iMac of otherwise identical specification, on on intel. Hmm. I was thinking this was an intel issue.
Wonder if its a hardware problem (though I suspect not).

[Solved] No sound after resuming from suspend

After suspending and resuming I no longer have any sound output (through headphone jack or my laptop speaker). The laptop is a toshiba portege r835. I can't say how long this has been happening, since I've only tried to play any sounds after resuming recently.
Searching the forums I found the following thread: https://bbs.archlinux.org/viewtopic.php?id=151001
I haven't tried this because it isn't exactly the same problem, but mostly because I'm currently stuck on kernel 3.5.6 because of the sandy bridge power regression issues.
Does anyone have any other ideas on how to possibly fix this problem?
Thanks!!
Last edited by twistedcubic (2012-12-31 22:20:20)

Solved, sort of.
I had some double suspend issue: I had set up suspend with systemd before using xfce and then after installing xfce I set my power settings so that the computer would suspend after shutting the lid, so I would have to open the lid, shut it, and then open it again for the computer to actually resume. After turning off the suspend setting in the xfce power manager, and just using the systemd suspend, the sound works fine on resume (both headphones and speakers)!

High CPU load after resuming from sleep mode

When my laptop resumes from sleep mode, LabVIEW 2012 starts to generate a very high and always constant CPU load (25%) without any VI running. I need to close all front panels to get back to the usual <1% CPU load level.
This behaviour spoils my carbon footprint and frequently eats up my battery. Any ideas what is causing this ?
Thank you,
Dirk

I'm guessing your issue may be related to this:
http://forums.ni.com/t5/LabVIEW/Why-is-using-100-of-a-CPU-1-out-of-8-when-it-does-nothing/m-p/242745...
Dirk@LV wrote:
This behaviour spoils my carbon footprint and frequently eats up my battery.
Thank you,
Dirk
Sorry about your carbon footprint, NI has a lot to answer!
Beginner? Try LabVIEW Basics
Sharing bits of code? Try Snippets or LAVA Code Capture Tool
Have you tried Quick Drop?, Visit QD Community.

[SOLVED]No sound after resuming from suspend thinkpad t23

On a T23 Thinkpad, suspend-to-ram works, but I have no sound and no network when resuming.
After googling for a while, it seems I must unload sound modules before going to sleep and then reload my sound modules after resuming.
lsmod|grep snd gives me this:
snd_intel8x0 28700 3
snd_ac97_codec 94756 1 snd_intel8x0
snd_pcm_oss 38432 0
snd_pcm 68996 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 19332 1 snd_pcm
snd_page_alloc 8072 2 snd_intel8x0,snd_pcm
snd_mixer_oss 14464 1 snd_pcm_oss
snd 44388 12 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss
soundcore 6496 1 snd
ac97_bus 2432 1 snd_ac97_codec
However, from the command line, after
modprobe -r snd_seq_oss snd_seq snd_seq_device snd_intel8x0 snd_ac97_codec snd_pcm_oss snd_pcm snd_timer snd_mixer_oss
I get:
FATAL: Module snd_intel8x0 is in use.
Even though I have no sound apps running.
I am planning on putting the modprobe -r command in /etc/pm/sleep.d/whatever to unload and then another to reload the mods.
Any help appreciated.
Last edited by Misfit138 (2008-01-07 02:27:07)

OK, solved it. Placed this in /etc/pm/sleep.d/11suspend
#!/bin/sh
mixers="Master PCM CD"
for mixer in $mixers ; do
/usr/bin/amixer -q sset $mixer mute
/usr/bin/amixer -q sset $mixer unmute
done
Just mutes and unmutes master, PCM and cd channels. Works perfectly. suspend-to-ram and hibernate now work 100%.
Thinkpads are so sweet.

Firefox crashing after resuming from sleep

For the past month or so after resuming my computer from sleep, firefox will crash as soon as I pull it up if it was minimized, or crash immediately if it was the active object before my computer went to sleep. I've tried safe mode, and it didn't work.
Last five crash reports:
bp-5f822abd-ca92-4eda-b05c-e02ab2140622
bp-3009d8d3-5d6f-43d4-a5c6-73fb22140621
bp-09d83832-4a4f-48c9-96f9-535c02140621
bp-1a8f4963-fc7f-40a6-abe3-d72862140620
bp-53774bda-2d27-41be-9a1e-85ff22140619

In the latest crash report;
Related Bugs
1027103 NEW --- Google Maps Street View crashes in gfxContext::PushClipsToDT(mozilla::gfx::DrawTarget*)
1011864 NEW --- Mozilla Firefox 29.0 crash (pointing to Null ) with window.open and very large sizes (PushClipsToDT signature)
1011348 NEW --- Crash/freeze when rendering certain private-use characters at font-sizes greater than about 1300%
1010262 NEW --- crash in gfxContext::PushClipsToDT(mozilla::gfx::DrawTarget*)
1002546 RESOLVED DUPLICATE crash in gfxContext::PushClipsToDT(mozilla::gfx::DrawTarget*)
974656 NEW --- Linux crash in gfxContext::PushClipsToDT(mozilla::gfx::DrawTarget*)
877629 RESOLVED WORKSFORME Opening http://elijahmanor.github.io/talks/angry-birds-javascript/index.html crashes the latest Nightly
839805 RESOLVED WORKSFORME Sasquatch Music Festival website crashes Firefox
805406 REOPENED --- crash in gfxContext::PushClipsToDT with Direct2D 1.1 (d3d11.dll 6.2 or 6.3)
803949 RESOLVED FIXED Crash [@ gfxContext::PushClipsToDT]
793175 VERIFIED FIXED Firefox 18 spike in crashes @ gfxContext::PushClipsToDT while hovering over tab preview in Task Bar
758531 RESOLVED FIXED crash in gfxContext::PushClipsToDT
734948 RESOLVED WORKSFORME Various crashes with gfx.content.azure.enabled

Windows 7 No sound after resume from sleep p-105

Similar Messages

Maybe you are looking for