Windows 7 not correctly recognize USB Microphone Samson G-Track

Hello Microsoft community members!
I have some problem with my Microphone Samson G-Track. I have installed on my Computer Windows 7 SP1.
After I connect USB Microphone over USB directly to PC, Windows 7 had been recognize it but into the START -> CONTROL PANEL -> SOUND -> RECORD
Microphone recognized like "line" not like "Microphone" device.
As a result many programs does not recognize this device as a microphone even Windows 7 wrote "Microphone not connected".
Need your assistance please.

The correct source of assistance with this situation is directly from
http://www.samsontech.com/samson/products/microphones/usb-microphones/gtrack/ as they are the manufacturer of the hardware and have sole responsibility for support of their product. This is not a Microsoft product and Microsoft does not provide support
for third party hardware.
I especially recommend you download and read
Samson G Track FAQ's V2.0
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ”

Similar Messages

Fails to recognize USB microphone

Just yesterday I was able to use my Logitech USB microphone in the Voice Over mode. I could select it from the pull down menu within the Voice Over window and very easily record scratch narration. Today? Nada. It's not available as a choice in Voice Over. It's like the computer doesn't even see it. I have rebooted the computer and restarted Final Cut, all to no avail. I even plugged the device into the USB port in the back of the computer. Nothing works. Any idea on how I can get this mic to show up again in Voice Over so I can use it?
Thanks,
David

Okay, problem solved. First, thanks so much to everyone who responded to this cunundrum. I think the culprit was downloading software updates yesterday. Because, I just now downloaded another small batch of software updates. As soon as I rebooted after the download installations, I looked in the System Preference Control Panels under Audio. And behold! The computer recognized the USB mic device. When I opened my Final Cut project, the Voice Over window gave me the mic as a input device. It works now just fine. So, that software download stuff can cut both ways. It could be that I needed to download yesterdays batch before I had access to today's batch. But, just availing myself of yesterday's batch appears to have rendered the device unrecognizeable. the latetest update appears to have solved the problem. In any event, thanks again to everyone for trying to bail me out. Hopefully, my problem and this response can help someone else with a similar problem in the future.
David

Windows 7 not forgetting disconnected USB devices, only on one PC, but not others/difer OS

Okay so I've got 3 computers:
1. Asus M5A99X EVO MOBO, Windows 7 Ultimate 64bit
2. Lenovo Ideapad u310 LAPTOP, Windows 8 (just 8)
3. Asrock z87e-ITX MOBO, Windows 7 Ultimate 64 bit and Windows 8.1 Pro 64-bit
This issue only happens on computer 3 under windows 7.
I've got a KVM switch that's supposed to make switching between these computers easier, it's very basic, it has one USB port going into it, and I plug my keyboard into that, my keyboard has a USB port on it that I plug my mouse into.
When I'm on windows 7 on computer 3 the KVM works fine for about the first 4-7 switches between it and another computer. But after that I get "USB Bandwidth Exceeded" popups. I can switch the port it's plugged into the computer and it will start
working again, but that defeats the purpose of having a KVM. And today it even locked up while I was MANUALLY switching the cable between my computers front access ports, because obviously the KVM wasn't reliable (like I switched between computers once every
4-10 minutes), and even BSOD on me.
I've contacted both Asrock and the KVM manufacturer and they both say it's the other's fault.
So I shrank my C: on Comp3 today and installed windows 8.1 on it, and than I spammed the KVM switching like 8+ times, and it never once locked up or complained about me exceeding the bandwidth.
So that means it's now Windows 7's fault, but it doesn't do this for Comp1.
Somehow my new computers Windows 7 is not working right, and I don't know any viable options I can do about it. (comp3 is only about 1-2 weeks old) I've ran all the windows updates I can and it no longer says there are new updates when i run it.
So I need some help about finding out why my Comp3's Win7 isn't forgetting that a USB device is no longer attached, because Win8.1 seems to have no problem with it.
And just sticking with Windows 8 isn't really the solution, as I can't %^#$#!@ stand Windows8/Metro/Tiles/tablet$@!#onmydesktop.
(laptop is a work laptop and i have no choice, but it's modded so I have my start menu back, but still it's annoying anytime I accidentally leave my desktop.)

...because it happens with even just the keyboard.
Even though it all works with Win8.1 have you:
-Tried a different keyboard?
-Tried connecting mouse and keyboard to an external powered hub and connecting the hub to the kvm?
-Tried connecting kvm to powered hub?

Quicktime Plugin crashes and Window size not correct when running a course from an LMS (Coursemill)

I am trying to run a course from an LMS (Coursemill) and a couple issues are occurring.
First, the quicktime plugin crashes, therefore the mp3 sound of the course does not play. When I reload the page, I get an "Unable to find API adapter" error message and the page won't load.
Also, the predetermined window size does not work properly and I end up with vertical and horizontal scroll bars which I do not want.
These issues are of high importance and need a solution ASAP. Please contact me.

If you haven't already visited the using QuickTime Plugin with Firefox KB article, I would recommend you first start there. If your problem still persists & no solution is found after referencing it just reply back to this response & we will go another route.
See:
[[Using the QuickTime plugin with Firefox]]

Console does not correctly recognize browser

Hi!
I've got Netscape 4.74 on Windows 2000, but the Console complains that this browser has not been
tested for 6.0 beta even though Windows 2000/Netscape 4.7x is listed as a supported combination.

I have the same problem when running Netscape 4.76 on windows 2000 but the
Console complains that this browser has not been tested for the console ?
Did you solve the problem yet ?
Thank you!
David
"Kumar Allamraju" <[email protected]> wrote in message
news:[email protected]..
Hi Uwe,
Our developer is asking the following question.
We need the output from http://<url>/console/common/requestinfo.jsp
so that we can tell what the user-agent values are for all of thesevarious browsers.
Pls post the snapshot here or send me an email directly.
Kumar
Uwe Meyer wrote:
Hi!
I've got Netscape 4.74 on Windows 2000, but the Console complains that
this browser has not been
tested for 6.0 beta even though Windows 2000/Netscape 4.7x is listed asa supported combination.
>

RH9 - window caption not correct in generated html-output

I installed RH9 and opened an existing project coming from RHX5 in the new RH9.
When generating HTML Help, the window caption of the output displays "HTML Help" instead of the name I gave to the default window (in my case: "Rimses 5.6 Help").
In RHX this was related to the default language in the Robohelp-project (Dutch in my case) versus the Regional settings of the PC.We had a workaround by adding in the HHP-file / Section "Options" the text "Language=0x409 English (United States)".
Now, in RH9, this workaround is not working anymore.
I tried several things:
- removing he workaround in the HHP-file
- changing the regional settings of my PC
- checking the project settings, html settings, default window etc.
Anyone an idea how to solve this in RH9?
thanks,
Natacha

Hi Natacha and welcome to the RH forums. Have you tried creating a new window? I wonder whether the old settings are causing RH9 to throw a wobbly and by starting afresh it may give it a shove where it is required.
The RoboColum(n)
@robocolumn
Colum McAndrew

E52 does not correctly recognize phone numbers.

Hi.
I have two contacts with the following (example) phone numbers in the address book: +48506123456 and +48606123456. They differ with only one digit, but the phone cannot recognize them and cannot display correct contact name while ringing.
Is there any solution?
Regards.
Booboo.
Solved!
Go to Solution.

Hi.
Both contact have only one number. But it seems, that phone cannot differ the number +48506123456 of contact1 from number +48606123456 of contact2.
Therefore, when one of this contact ringing, I see only the number instead of contact name. In addition, when I remove one of the contacts, regardless whose one ringing, I see left one.
It looks like number +48506123456 and +48606123456 are the same for phone (last six digit was changed for privacy).
Regards.
Booboo.

Windows 7 doesn't recognize usb 6221

Hi,
I had an application (plus the entire package with Runtime and DAQmx) in Labview which is deployed on several PC. Until now it worked just fine on PCs with WinXP.
Now I have to install the same application on a PC with Win7. The problem is the LabView cannot recognize the USB6221 board.
In Windows Device Manager the board is there, but LabView sees nothing. Also, if I check in Measurement and Automation I cannot see the board there. I installed and reinstalled the entire software but no results.
Does anzbody had the same experience or could anybody give me some hints??
Thanks,
Paul
Message Edited by PaulieQ on 04-23-2010 06:02 AM
Solved!
Go to Solution.

Dear Pauline,
There are some factors you need to
consider while porting to windows 7 platform. As far as i know, only
labview 2009 software is fully compatiable with windows 7.
Meaning
to dispatch to windows 7, you will need the following.
i)
Labview runtime engine (Labview 2009)
ii) Any drivers
(DAQ, DAQmx ) compatiable with windows 7.
iii) exe created
by labview 2009.
Last time, i also face similar problems. I build
the exe in windows Xp platform (Labview 8.6) and i can dispatch to
windows Xp and Vista platform. However when i port the exe to windows 7
platform, i also cant get it to work well after many tries.
Finally,
i just upgrade to Labview 2009 and compile the exe under windows 7
platform. Dispatch this exe together with the lastest drivers (windows 7
drivers) and my exe works well for all platforms (XP, Vista and windows
7) now.
This may be something you like to try out.

Windows XP used to recognize USB 2.0, now it doesnt...

I've had an iPod for a little under six months and got a laptop Compaq Presario M2000, the iPod was always recognized and I could put music on there and everything but then I updated the iTunes to 5.0 and then 5.1 and now everytime I connect through the USB it says the "device is not recognized, no drivers installed" I have done EVERYTHING imaginable, spending more then seven hours trying to fix it! I looked on here and nothing has helped...I dont want to restore my iPod because then I lose all of my music and I dont have anything backed up because I cant hook it up to my computer. I just don't understand why it used to work perfectly fine and now it doesnt, its not the cord or anything because I borrowed someone else's and the same message popped up! PLEASE HELP.

Try connecting using a firewire if available. Its the only solution that I have found to the problem.

USB Device Not Recognized - USB device attached has malfunctioned & Windows does not recognize it

I have an HP Pavilion dv4 Notebook running Windows 7 Home Premium and the USB ports worked fine for an HP deskjet printer and an older Casio digital camera. Then one day, the laptop decided not to recognize the Casio digital camera and gave the error message "USB Device Not Recognized" and also indicated that the device attached to the computer has malfunctioned. This prompted me to buy a new Canon digital camera. Well, a new camera did not fix the problem. Now, anything connected to either of the 2 USB ports will not be recognized by my laptop. Help! I'm at a loss to figure this out. I've tried the suggested Microsoft help below:
Suggestion 1: For the issue with USB devices, uninstall and re-install all the USB controllers. This lets the controllers recover the USB port from its unresponsive condition.
The USB controllers represent the USB ports in Device Manager.
a. Click Start, type device manager in the Start search box and hit Enter.
b. Expand Universal Serial Bus controllers.
Note: You might have to scroll down the list to find this item.
c. Right-click the first USB controller under Universal Serial Bus controllers, and then click Uninstall to remove it.
d. Repeat the above step for each USB controller that is listed under Universal Serial Bus controllers.
e. Restart the computer. After the computer starts, Windows will automatically scan for hardware changes and reinstall all the USB controllers that you uninstalled.
f. Check the USB device to see whether it is working.
This did not correct the problem. Then from device manager, I tried updating drivers on all the USB controllers and root hubs. While some may have received downloaded software updates, it still did not correct the USB device not recognized problem after restarting the computer. I'm hoping someone knows of the fix to this situation and can pass it along to me. Thanks for reading and posting any help.
This question was solved.
View Solution.

Hey 655micha,
I'm sorry you're having an issue with a USB device. Do you get an error window that pops up? If so what does it say? Have you checked Device Manager? Is is just one device that isn't working? Has it ever worked before? Is it just one USB port in particular that isn't recognizing devices?
What model do you have? Here are the steps to find your product number. FN + ESC is the easiest way to find that information.

Cant Charge/connect ipod touch. Get an error saying "One of the USB devices attached to your computer has malfunctioned, and Windows does not recognize it" . HELP.

Ok . so my ipod touch 2G , used to be all ok . its just yesterday i went to charge my ipod it wouldnt do anything . Then after being plugged in for a bit , i got pop up saying " "One of the USB devices attached to your computer has malfunctioned, and Windows does not recognize it" .
Ive tried plugging this into 3 other computers same error message pops up .
PLEASE help me . thanks (:

Uninstall your USB drivers in your computer & reinstall.
contact your pc manufacturer for the steps.
Although I am working on behalf of HP, I am speaking for myself and not for HP.
Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
Happy Troubleshooting : )

USB device (1 day old nano) has malfunctioned & windows does not recognize

Please can someone help a non-tech savy new ipod user. I have loaded the latest itunes, but not only does itunes not see my ipod, I get the following windows error when I plug it in. "One of the USB devices attached to this computer has malfunctioned and windows does not recognize it". It says no drivers are loaded for this device. I have followed the 5Rs including the windows updates with no luck. If anyone can help I would really appreciate it.
Thanks
sampsona

You listed as having an IBM r40. If I'm not mistaken, that's a laptop. The usb ports on many laptops aren't USB 2.0 or are low power ones. This can cause problems with a nano being able to charge.
One thing to try is to get a wall adapter to charge the nano separately, then connect to your computer for syncing only. You can find adapters locally and through Apple Store. http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?mco=C39 415D1&nclm=iPodPower
You can also try buying a POWERED usb hub. Make sure it has it's own power source so that its ports have enough charge to support the nano.
Custom PC & iMac (DV Special Edition), iPod Nano 1st, iPod Click Wheel Windows XP Pro Work in a variety of PC and Mac environments

One of the usb devices attached to your computer has malfunctioned, and windows does not recognize i

I am a damsel in distress. Every time I turn on my printer, I get ths message: "One of the USB devices attatched to your computer has malfunctionedand windows does not recognize it: . All was fine until I put in new ink today. I had not used the printer for about ten days prior to this. I went through the HP line of troubleshooting but nothing has worked. I have Windows 7 64 bit
Thank you
Katt

Uninstall your USB drivers in your computer & reinstall.
contact your pc manufacturer for the steps.
Although I am working on behalf of HP, I am speaking for myself and not for HP.
Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
Happy Troubleshooting : )

I have a ipod nano 1st and 2nd generation and am trying to put music on it but every time windows says one of the usb devices attached to this computer has malufunctioned and windows does not recognize it code 43 can someone help me please

i have a ipod nano 1st and 2nd generation and am trying to put music on it but every time windows says one of the usb devices attached to this computer has malufunctioned and windows does not recognize it code 43 can someone help me please

Try putting it into "Disk Mode" http://docs.info.apple.com/article.html?artnum=93651
Then with it in this mode connect it to the PC and try to run the latest iPod updater to do a restore and update software if you have the option. the latest iPod updater is 2006-03-23 and can be downloaded here http://www.apple.com/ipod/download/

My computer will not recognize my ipod touch anymore. When I plug it in it says the USB device attached to this computer has malfunctioned and windows doesn not recognize it.

My computer (PC) will not recognize my ipod touch anymore. When I plug it in, it says the USB device attached to this computer has malfunctioned and windows does not recognize it. I have tried attaching the same cord and ipod to a different computer and it is recognized by our mac. I have tried restarting the ipod, downloading all updates on my pc, restarting the pc, etc. Nothing has worked. Please advise.

See:
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

Windows 7 not correctly recognize USB Microphone Samson G-Track

Similar Messages

Maybe you are looking for