Windows 7 not starting with 2nd HDD

Having lots of fun with this one.
Have a Mid 2012 MBP Classic. Recently purchased a HDD caddy for a second hard drive and a SSD (Crucial M500 480GB).
My intention is to run OS X Mountain Lion on a 400GB partition on the SSD, Boot Camp Windows 7 on the remaining 80GB, and then format the old 750GB Apple HDD in exFAT for storage both OSes can access.
I have everything running at the moment apart from the fact that I can't start Windows. I just get the usual 'No bootable device' error when I try.
If I disconnect the old 750GB drive it starts fine. If I run Windows as a VM in Parallels it starts fine. Otherwise I can't start it.
One thing I did have to do during Boot Camp setup is format the install 80GB as NTFS, which I assume is normal.
How can I make this work? I have already tried rEFIt which makes no difference. Modifying stuff via diskpart in Windows will break things-I've been there before!
Does anyone else have a similar setup to the above?

If windows see other drives with GUID it will not install.
Unplug
change it to FAT
You will get an error message otherwise.
Years of people using multiple drives, began in 2006 with Vista and Mac Pro, every SSD + hard drive iMac or MacBook or even two of anything.
I don't even think it cares about port 0 or 1 or "primary".
Swap the optical and SSD etc AFTER you install Windows.

Similar Messages

A 305- S6825 will not start with the battery and charger. There's no light, no noise on fan or HDD

PC will not start with the battery and charger. There's no light, no noise on fan, hard drive and CD writer. The hard drive, fan and charger are new. But I was havingproblems and sudden blackouts System 32. Try several times to install theoperating system but the pc turned off suddenly and restarted until I stop working completely. Now it does nothing and no light. I hope it can help me I need torespect and love very much this notebook.
Thanks in advance
Jose Echevarria
[email protected]

Turn off your laptop, unplug all wires, remove the battery, and hold the power button for thirty seconds. Afterwards, reattach the battery and connections. If it still won't start, remove the battery and start with just the AC power. Next try without the AC power and just the battery.
- Peter

HT5639 windows 7 starts with an error report

hi,can anyone help me to get windows back on to my imac.,i have a problem with uploading windows,it starts with an error report saying there is a problem
and gives me two options the 1st it tries to repair the problem and then tells me it cant repair it and when i click finish it closes down,the 2nd option
is start windows normally but when i scroll down to this option nothing happens.i used to have parallels but got so frustrated at this doing nothing i removed it
from my imac,but that did not help,can anybody help.
thanks

Hi Paul,
You don'y say what version of WMP you currently have, but I would strongly recommend installing the latest version from the Microsoft web site. It is possible that your current version has become corrupted in some way.
HTH

Worst update ever! On my Vista everything is wrong! Back button never active; If I want open pages as new tab it opens new window; FF starts with blank page instead of Google; No url address shown on status bar when I move mouse arrow on the link etc

Worst update ever! On my Vista everything is wrong! Back button never active; If I want open pages as new tab it opens new window; FF starts with blank page instead of Google; No url address shown on status bar when I move mouse arrow on the link etc.. Please Help!

Try the Firefox SafeMode to see how it works there. <br />
''A troubleshooting mode, which disables most Add-ons.'' <br />
''(If you're not using it, switch to the Default Theme.)''
* You can open the Firefox 4.0+ SafeMode by holding the '''Shft''' key when you use the Firefox desktop or Start menu shortcut.
* Or use the Help menu item, click on '''Restart with Add-ons Disabled...''' while Firefox is running. <br />
''Don't select anything right now, just use "Continue in SafeMode."''
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before using the Firefox shortcut (without the Shft key) to open it again.''
'''''If it is good in the Firefox SafeMode''''', your problem is probably caused by an extension, and you need to figure out which one. <br />
http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes
''When you figure out what is causing that, please let us know. It might help other user's who have that problem.''

My iphone can't back up to pc,because a session could not started with iphone.how fix the itunes

my iphone can't back up to pc,because a session could not started with iphone.how fix the itunes or iphone,this problem is after update ios7.0.4 and update itunes.pls teach me fix my pc,my pc is windows vista....

i have this problem too >> but i try other iphone ios7.0.3 i ok and work
but my ios7.0.4 cant back up and keep pop out session could not started with iphone !
really hope someone can help it ..
thank a lot !

How can I have multiple WINDOWS (NOT tabs) with INDEPENDENT content?

How can I have multiple '''windows''' (''not ''tabs) with '''independent''' content?
I used to be able to open separate windows with Firefox, and the content could be completely different in each window. No matter what I did in any window, no OTHER window open at the time, nor any of the content therein, was affected. This is no longer the case and it is extremely frustrating for me.
I do ''not ''like tabs and do not use them. I prefer multiple windows plus I am so used to using them, for so many years now! But with v9.0.1 I suddenly can no longer do what I've always done with my browser without this aggravating problem constantly reminding me that I can't have what I want in firefox anymore.
Or can I? Does anyone have a solution I don't realize exists?
Thanks,
Sowelu

AppleScriptObjC can use pretty much everything in the Cocoa API, so yes, it is possible.
Note that a view is not the same as a window, and a window can have multiple views. There are also many ways to implement "tabs"; take a look at some of Apple's applications - they use various mixtures of toolbars, checkboxes, and radio buttons, for example. An application such as this will be a lot more involved than what you have done so far though, using custom classes and subclassing existing ones, so be prepared to do a lot of reading and researching.

Property List error: Unexpected character b at line 1 / JSON error: JSON text did not start with array or object and option to allow fragments not set.

Hi,
I have a MBP 13' Late 2011 and Yosemite 10.10.2 (14C1514).
Until yesterday, I was using Garmin ConnectIQ SDK and all was working fine.
Yesterday, I've updated my system with latest security updates and Xcode updates too (Version 6.2 (6C131e)).
Since, I can't launch the ConnectIQ simulator app, I have this message in console :
8/04/2015 15:19:04,103 mds[38]: There was an error parsing the Info.plist for the bundle at URL Info.plist -- file:///Volumes/Leto/connectiq-sdk-mac-1.1.0_2/ios/ConnectIQ.bundle/
The data couldn’t be read because it isn’t in the correct format.
<CFBasicHash 0x7fa64f44e9a0 [0x7fff7dfc7cf0]>{type = immutable dict, count = 2,
entries =>
0 : <CFString 0x7fff7df92580 [0x7fff7dfc7cf0]>{contents = "NSDebugDescription"} = <CFString 0x7fa64f44f0a0 [0x7fff7dfc7cf0]>{contents = "Unexpected character b at line 1"}
1 : <CFString 0x7fff7df9f5e0 [0x7fff7dfc7cf0]>{contents = "kCFPropertyListOldStyleParsingError"} = Error Domain=NSCocoaErrorDomain Code=3840 "The data couldn’t be read because it isn’t in the correct format." (Conversion of string failed.) UserInfo=0x7fa64f44eda0 {NSDebugDescription=Conversion of string failed.}
I have looked at this file and it looks like a binary plist
bplist00ß^P^V^A^B^C^D^E^F^G^H
^K^L^M^N^O^P^Q^R^S^T^U^V^W^X^Y^Z^[^\^]^^^_ !"$%&'()'+,^[\CFBundleNameWDTXcodeYDTSDKName_^P^XNSHumanReadableCopyrightZDTSDKBuild_^P^YCFBundleDevelopmentRegion_^P^OCFBundleVersi on_^P^SBuildMachineOSBuild^DTPlatformName_^P^SCFBundlePackageType_^P^ZCFBundleShortVersionString_^P^ZCFBundleSupportedPlatforms_^P^]CFBundleInfoDictionaryVersion_^P^RCFBundleE xecutableZDTCompiler_^P^PMinimumOSVersion_^P^RCFBundleIdentifier^UIDeviceFamily_^P^QDTPlatformVersion\DTXcodeBuild_^P^QCFBundleSignature_^P^ODTPlatformBuildYConnectIQT0611[iph oneos8.1o^P-^@C^@o^@p^@y^@r^@i^@g^@h^@t^@ ^@©^@ ^@2^@0^@1^@5^@ ^@G^@a^@r^@m^@i^@n^@.^@ ^@A^@l^@l^@ ^@r^@i^@g^@h^@t^@s^@ ^@r^@e^@s^@e^@r^@v^@e^@d^@.V12B411RenQ1V14C109Xiphoneos TBNDLS1.0¡#XiPhoneOSS6.0YConnectIQ_^P"com.apple.compilers.llvm.clang.1_0S8.1_^P^Tcom.garmin.ConnectIQ¡*^P^AW6A2008aT????^@^H^@7^@D^@L^@V^@q^@|^@<98>^@ª^@À^@Ï^@å^A^B^A^_^A?^AT^ A_^Ar^A<87>^A<96>^Aª^A·^AË^AÝ^Aç^Aì^Aø^BU^B\^B_^Ba^Bh^Bq^Bv^Bz^B|^B<85>^B<89>^B<93>^B¸^B¼^BÓ^BÕ^B×^Bß^@^@^@^@^@^@^B^A^@^@^@^@^@^@^@-^@^@^@^@^@^@^@^@^@^@^@^@^@^@^Bä
I guess it is a normal format but my system seems to be unable to read binary plist ?
I tried some stuff with plutil
plutil -lint Info.plist
Info.plist: Unexpected character b at line 1
Same for convert
plutil -convert xml1 Info.plist
Info.plist: Property List error: Unexpected character b at line 1 / JSON error: JSON text did not start with array or object and option to allow fragments not set.
I also try to download a fresh version of the connectIQ SDK and no changes.
Any idea ?
Thanks

Step by step, how did you arrive at seeing this agreement?

Hi, Im from Philippines,.... i am currently using my iPhone 4 (iOs.6.3)it started when i upgrade it from iOs4 to iOs 6.3 , My iPhone doesnt identify numbers even if its in my contact if its not starting with +63 ..what will i do?

Hi, Im from Philippines,.... i am currently using my iPhone 4 (iOs.6.3)it started when i upgrade it from iOs4 to iOs 6.3 , My iPhone doesnt identify numbers even if its in my contact if its not starting with +63 ..what will i do?
I change everything into +63 and i thought everything is already fine,.. and then now , i dont know what happened why it doesnt recognize numbers with +63 anymore

Hello hsielglad,
Thank you for your question. iTunes 11.1 is required to update to and sync with iOS 7. If you are still running iTunes 10.6.3, I recommend trying to obtain the update by going to the iTunes menu and selecting Check for Updates.
iTunes: How to install the latest version
http://support.apple.com/kb/HT5654
If you continue to get the message that iTunes is up to date, you can download the latest version of iTunes here:
Download iTunes
http://www.apple.com/itunes/download/
Once the file downloads, double click on the installation file that downloaded to initiate the installation.
Best,
Sheila M.

Error: response does not start with HTTP

hi,
i am using a MIDP class to send a string to a java servlet which then returns a .gif image. the string is being successfully to the servlet, but an exception is being thrown when the image is being sent back.
java.io.IOException: response does not start with HTTP it starts with: GIF89aï4
at com.sun.midp.io.j2me.http.Protocol.readResponseMessage(Protocol.java:2166)
at com.sun.midp.io.j2me.http.Protocol.finishRequestGetResponseHeader(Protocol.java:1934)
at com.sun.midp.io.j2me.http.Protocol.sendRequest(Protocol.java:1598)
at com.sun.midp.io.j2me.http.Protocol.sendRequest(Protocol.java:1517)
at com.sun.midp.io.j2me.http.Protocol.openInputStream(Protocol.java:484)
my code is as follows in the midp class :
HttpConnection c = null;
InputStream is = null;
StringBuffer sb = new StringBuffer();
String url="http://localhost:8090/ProjectServer/createMap";
url=url+"?Source="+src+"&Destination="+dest;
try {
c = (HttpConnection)Connector.open(url,Connector.READ_WRITE, true);
c.setRequestMethod(HttpConnection.GET); //default
//is = c.openDataInputStream();
is = new DataInputStream(c.openInputStream()); //openInputStream(); // transition to connected!
Image im=null;
try
ByteArrayOutputStream bStrm = new ByteArrayOutputStream();
int ch;
while ((ch = is.read()) != -1)
bStrm.write(ch);
// Place into image array
byte imageData[] = bStrm.toByteArray();
// Create the image from the byte array
im = Image.createImage(imageData, 0, imageData.length);
finally
// Clean up
if (is != null)
is.close();
the code in the servlet is as follows :_
ServletContext sc = getServletContext();
// Get the MIME type of the image
String mimeType = sc.getMimeType("route.gif");
if (mimeType == null) {
sc.log("Could not get MIME type ");
response.setStatus(HttpServletResponse.SC_INTERNAL_SERVER_ERROR);
return;
// Set content type
response.setContentType(mimeType);
// Set content size
response.setContentLength((int)file.length());
// Open the file and output streams
FileInputStream in = new FileInputStream(file);
OutputStream outstream = response.getOutputStream();
// Copy the contents of the file to the output stream
byte[] buf = new byte[1024];
int count = 0;
while ((count = in.read(buf)) >= 0) {
outstream.write(buf, 0, count);
in.close();
outstream.close();
il be immensely grateful if some1 cud tell me whre i am gng wrong.
thnx,
nev

Hi, I�m trying to do the same as above, get MP3 from a Shoutcast server.
I got the same fault ("response does not start with HTTP it starts with: ICY") when I tried to open an HttpConnection as bellow:
============================================
HttpConnection conn = (HttpConnection) Connector.open("http://64.236.34.196/stream/1074");
Then I tried to open a socket connection as bellow:
======================================
SocketConnection conn = (SocketConnection) Connector.open("socket://64.236.34.196:80");
String get = "GET /stream/1074 HTTP/1.1";
DataOutputStream os = conn.openDataOutputStream();
os.writeUTF(get);
InputStream is = conn.openInputStream();
But then I got the following error:
=========================
java.lang.SecurityException: Target port denied to untrusted applications
Could someone help me to find out what is going on?
Thanks a lot!

A name should not start with any special characters

I need to put a condition in iF statement such that a name that is given by the user should not start with any special charecters.A dialog box should display indicating this conditon.Can u plz give sample code for this.My code is as below.
//text box for giving the name
JTextFeild ReportNameText;
//the name is stored in String
String name=ReportNameText.getText();
//Here tell me how the if condition should be written
//condition to be mentioned

Already asked, and answered, here: http://forum.java.sun.com/thread.jspa?threadID=727919
See reply 4 in that thread, and scsi-boy's suggestion of writing another
method to check for "special" characters. And the links to the String
and Character API documentation given.

"Layer 1 does not start with a new cell" replicator error

Hi All,
I recently sent a dual layer +R DVD off to our replication house and their system is returning a message that says: "Layer 1 of DVD-Video does not start with a new cell".
I know from reading that the dual-layer breakpoint must be set to the end of a cell, but what does the word "cell" translate into for DVDSP4?
I had the DVD DL+R set to Automatic and Non-Seamless for output for the break point. Should I just try setting the break point manually at the beginning or ending of a track that would be dubbed as just a little more than half the size of the content? (I know in OTP, the Layer 0 has to be bigger than Layer 1)
Please Help!
Cheers,
Dusty

Thanks both of you for your replies.
Eric, I am currently exporting DDPs to send in to the replicator. I also emailed them asking if they accept this format for delivery. (Which I would hope they would, as it is, an answer to DLT of sorts) Thanks for bringing this up, DDP is new to me, as this is our first DL project for replication.
Drew, to answer your reply, yes I have two viable markers (chapter markers) that show up in black, not grayed out, in the tab you mentioned under formatting. I chose manual break point selection for this last disc I burned and chose chapter 4 of that track. (chapter 4 and chapter 5 of track 6 are only options) I have to assume that the "automatic" setting was selecting chapter 5, as it had to see that as the last viable marker available to select, as described in the DVDSP4 manual.
DVDSP4 says that all markers are considered cells- Or actually that tracks are cells and that the markers within them make up more cells. So my question, outside of DDP option, would be, "what truly constitutes a cell boundary in DVDSP4?" Is it the markers within the tracks or the beginning or ends of the tracks themselves?
As a side note, I burned the disc that received the error, "Layer 1 doesn't start with a new cell" from an IMG i created from DVDSP4 through Disk Utility. Word is that IMG's somehow don't include breakpoint information.
So at this point I don't know if it is the IMG or the fact that DVDSP4 wants the break at one of two possible chapter markers in track 6.
(Some more background- this is a TV show season DVD, with thirteen tracks of video, each with 12-14 chapter markers a piece.)
Any more thoughts to help clear the air on what constitutes a true new cell boundary?
Thanks sooo much Eric and Drew, I know this a long read.
Cheers,
Dusty

Path login does not start with a "/" character

I get a "java.lang.RuntimeException: Path login does not start with a "/" character" in my WebApplication.
- Http Status 500
- The server encountered an internal error () that prevented it from fulfilling this request.
Instead I excepted the site for a Re-Login (timout after 10 min), What's wrong?
The server I use is: Sun Java System Application Server Platform Edition 8.0 (build b57-fcs)
Here is the full StackTrace:
[#|2004-05-26T14:50:50.609+0200|SCHWERWIEGEND|sun-appserver-pe8.0|javax.enterprise.system.container.web|_ThreadID=17;|Standard
WrapperValve[OwaFolderTree]: Servlet.service() for servlet OwaFolderTree threw exception
java.lang.RuntimeException: Path login does not start with a "/" character
at org.apache.catalina.core.ApplicationContextFacade.doPrivileged(ApplicationContextFacade.java:451)
at org.apache.catalina.core.ApplicationContextFacade.getRequestDispatcher(ApplicationContextFacade.java:255)
at com.space2go.icafe.S2GHttpServlet.service(S2GHttpServlet.java:3260)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:861)
at sun.reflect.GeneratedMethodAccessor114.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:324)
at org.apache.catalina.security.SecurityUtil$1.run(SecurityUtil.java:289)
at java.security.AccessController.doPrivileged(Native Method)
at javax.security.auth.Subject.doAsPrivileged(Subject.java:500)
at org.apache.catalina.security.SecurityUtil.execute(SecurityUtil.java:311)
at org.apache.catalina.security.SecurityUtil.doAsPrivilege(SecurityUtil.java:205)
at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:283)
at org.apache.catalina.core.ApplicationFilterChain.access$000(ApplicationFilterChain.java:102)
at org.apache.catalina.core.ApplicationFilterChain$1.run(ApplicationFilterChain.java:192)
at java.security.AccessController.doPrivileged(Native Method)
at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:188)
at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:263)
at org.apache.catalina.core.StandardValveContext.invokeNext(StandardValveContext.java:156)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:569)
at org.apache.catalina.core.StandardContextValve.invokeInternal(StandardContextValve.java:261)
at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:215)
at org.apache.catalina.core.StandardValveContext.invokeNext(StandardValveContext.java:156)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:569)
at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:200)
at org.apache.catalina.core.StandardValveContext.invokeNext(StandardValveContext.java:156)
at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:180)
at org.apache.catalina.core.StandardValveContext.invokeNext(StandardValveContext.java:154)
at org.apache.catalina.valves.AccessLogValve.invoke(AccessLogValve.java:582)
at org.apache.catalina.core.StandardValveContext.invokeNext(StandardValveContext.java:154)
at com.sun.enterprise.webservice.EjbWebServiceValve.invoke(EjbWebServiceValve.java:134)
at org.apache.catalina.core.StandardValveContext.invokeNext(StandardValveContext.java:154)
at com.sun.enterprise.security.web.SingleSignOn.invoke(SingleSignOn.java:272)
at org.apache.catalina.core.StandardValveContext.invokeNext(StandardValveContext.java:154)
at com.sun.enterprise.web.VirtualServerValve.invoke(VirtualServerValve.java:209)
at org.apache.catalina.core.StandardValveContext.invokeNext(StandardValveContext.java:154)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:569)
at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:161)
at org.apache.catalina.core.StandardValveContext.invokeNext(StandardValveContext.java:156)
at com.sun.enterprise.web.VirtualServerMappingValve.invoke(VirtualServerMappingValve.java:166)
at org.apache.catalina.core.StandardValveContext.invokeNext(StandardValveContext.java:154)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:569)
at org.apache.catalina.core.ContainerBase.invoke(ContainerBase.java:979)
at org.apache.coyote.tomcat5.CoyoteAdapter.service(CoyoteAdapter.java:211)
at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:692)
at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.processConnection(Http11Protocol.java:647)
at org.apache.tomcat.util.net.TcpWorkerThread.runIt(PoolTcpEndpoint.java:589)
at org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run(ThreadPool.java:691)
at java.lang.Thread.run(Thread.java:534)

It looks like you are getting this error when trying to use the RequestDispatcher. There are two different flavors of the RequestDispatcher :ServletRequest.getRequestDispatcher that will take a relative path and ServletContext.getRequestDispatcher that will only take absolute paths (ie start with a '/').
If yoy are trying the use the second version of RequestDispatcher you'll need to adjust the path to an absolute path.
http://java.sun.com/products/servlet/2.3/javadoc/javax/servlet/ServletContext.html

HWS file error when not starting with Ch 0

Hello,
I used the "niScope EX Save to File - HWS Low Level - Single Channel Stream.vi" as my starting point and added 8 channels for a 5105 card. Although this is a complex Queue-based vi, it works fine as long as my RAID is fast enough.
However, we have need to take data from channels 4 to 7 and not start with Ch 0. When I do this, my LabVIEW HWS reader does not see any data, nor does the MATLAB code I have written to read our HWS files.
Looking at the file in HDFView, I see that the data starts in vector0 and not vector1, as when I record Channels 0 to 3.
Perhaps I need to use the HDF5 LabVIEW code to force the writing to a different location in the HDF file?
Thanks for your help.

Hello,
I was out of the office Mon. and Tues. I took out a section that just collects one 5105 card in a steaming, continuous collect mode. This is part of a much bigger VI and I included the “Helper Aps” folder that has all the sub-VIs for that larger app. There are more sub-VIs than you need for “5105 Cont Collect.vi”, but it should run once you tell it where the sub-VIs are. Included is a quick-look reader I use to look at the data.
The data file Ch_0_to_3_5105-0.hws can be read, but the Ch_4_to_7_5105-0.hws file cannot.
Thank you for your help.
Attachments:
5105_Cont_Collect.zip ‏3267 KB

DB is not starting with spfile .

Hi ,
i am running DB (10.2.0.4) DB on solaris.x64 platform.
When i started the database after install , its giving error as
SQL> startup
ORA-00064: object is too large to allocate on this O/S (1,3994560)
I checked the sga_target size in spfile , which is set to (729145600 bytes ~ 595 M)
When installed another DB with sga_target size as 412 M
and started the DB it gives follwing error .
SQL> startup
SQL> ORA-00821: Specified value of sga_target 412M is too small, needs to be at least 552M
if i start the same DB with pfile where sga_target has set to 1632 M , the DB is starting successfully.
My question is if it is starting with this higher value of sga_target in with pfile , why it is not starting with a lesser value.

Cause: The specified value of sga_target is too small for the SGA to accommodate all of the necessary SGA components such as the log buffer, buffer pools, shared pool, etc.
Action: Set sga_target to the recommended value or reduce the values of any SGA component size parameters you have specified.
The previous solutions where correct, but if you're not providing a full path on the "CREATE SPFILE" make sure you have defined the parameter SPFILE. Otherwise you'll get the SPFILE created on $ORACLE_HOME/dbs/spfileDBNAME.ora
Regards,
Enric Moya

Managed server is not starting with MSI mode

Managed server not starting with MSI mode even though we enabled the managed server independence mode
Started the admin server and managed server first time enabled the MSI mode.
Restarted all admin and Managed server.
We have tested the following scenarios
scenarios1: Stopped the Admin server and restarted the Managed server with MSI mode it comes up.
scenarios2:Admin server is running but not able to connect to the managed server
In this scenario
we have removed the Network cable and restarted the managed server its throwing ldap error.
<Aug 14, 2010 1:58:32 PM SGT> <Error> <Security> <BEA-090870> <The realm "myrealm" failed to be loaded: weblogic.security.service.SecurityServiceException: com.bea.common.engine.ServiceInitializationException: weblogic.security.spi.ProviderInitializationException: [Security:090730]Failed to verify credential mapper LDAP hierarchy
netscape.ldap.LDAPException: failed to connect to server ldap://sgppsr00383:16827 (91)
at netscape.ldap.LDAPConnSetupMgr.connectServer(LDAPConnSetupMgr.java:515)
at netscape.ldap.LDAPConnSetupMgr.openSerial(LDAPConnSetupMgr.java:435) at netscape.ldap.LDAPConnSetupMgr.connect(LDAPConnSetupMgr.java:274)
at netscape.ldap.LDAPConnSetupMgr.openConnection(LDAPConnSetupMgr.java:199)
at netscape.ldap.LDAPConnThread.connect(LDAPConnThread.java:109)
at netscape.ldap.LDAPConnection.connect(LDAPConnection.java:1083) at netscape.ldap.LDAPConnection.connect(LDAPConnection.java:954)
at netscape.ldap.LDAPConnection.connect(LDAPConnection.java:781)
at weblogic.ldap.EmbeddedLDAPConnection.getAndInitDelegate(EmbeddedLDAPConnection.java:2031)
at weblogic.ldap.EmbeddedLDAPConnection.add(EmbeddedLDAPConnection.java:1065) at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.addEntry(DefaultCredentialMapperLDAPHelper.java:537)
at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.createOrgUnit(DefaultCredentialMapperLDAPHelper.java:432)
at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.verifyHierarchy(DefaultCredentialMapperLDAPHelper.java:407)
at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.<init>(DefaultCredentialMapperLDAPHelper.java:146) at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.getInstance(DefaultCredentialMapperLDAPHelper.java:112)
at weblogic.security.providers.credentials.DefaultCredentialMapperProviderImpl.initialize(DefaultCredentialMapperProviderImpl.java:93)
at com.bea.common.security.internal.legacy.service.SecurityProviderImpl.init(SecurityProviderImpl.java:53)
at com.bea.common.engine.internal.ServiceEngineImpl.findOrStartService(ServiceEngineImpl.java:340) at com.bea.common.engine.internal.ServiceEngineImpl.findOrStartService(ServiceEngineImpl.java:292)
at com.bea.common.engine.internal.ServiceEngineImpl.lookupService(ServiceEngineImpl.java:263)
at com.bea.common.engine.internal.ServicesImpl.getService(ServicesImpl.java:71)
at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initializeRealm(CommonSecurityServiceManagerDelegateImpl.java:461) at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.loadRealm(CommonSecurityServiceManagerDelegateImpl.java:822)
at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initializeRealms(CommonSecurityServiceManagerDelegateImpl.java:851)
at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initialize(CommonSecurityServiceManagerDelegateImpl.java:1007)
at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:854) at weblogic.security.SecurityService.start(SecurityService.java:141)
at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64) at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209) at weblogic.work.ExecuteThread.run(ExecuteThread.java:181)
- with nested exception:
Managed server looking for ldap configuration from admin server.
I have checked the all configuration file same on both managed server and admin server.
Please let me know How to recover the managed server in this scenario.
Edited by: user10773210 on Aug 16, 2010 11:55 PM
Edited by: user10773210 on Aug 17, 2010 2:38 AM

thanks for the reply....
the managed server is pointing to jrokit_160_22_D1.1.1-3 jdk....the server has enough ram also...while running the managed server showing status 'STARTING' for long period of time...and the admin server health goes 'Warning' because of threadpool....when we stop the managed server then adminserver health becomes ok...

Windows 7 not starting with 2nd HDD

Similar Messages

Maybe you are looking for