Windows 7 periodically crashed with my Mac Mini since 1.5 months ago.

Using Mac Mini late 2012 I7 CPU. Windows 7 Ultimate (authentic). Last version bootcamp. Have been running Windows 7 Ultimate since 2013 and was very stable and reliable. A month ago all in a sudden it crashed and not even using an image recovery could get it to work. Deleted the windows partition and re-installed Windows (a few times) using latest bootcamp drivers (3.5), but since then Windows keep crashing every 2 weeks or so. The good thing is that using image recovery can bring it back to life (for a while). Installed programs are minimal: Office 2010 (authentic), Windows Essential 2012, Norton 360, open office, 7-zip, Photoshop element 9 (authentic), Filezilla etc..very minimal but still having the same problem. any suggestion? Anyone?

Sorry for taking so long to reply on this issue, too busy.
It is still happening.
First confirmed that after using Windows disc image to recover, the Event Viewer is recovered to older dates so there is no record of the crash.
Strange is that when I used AHT to test the hardware (last week), there was no error at all but today there are, frequently (almost once every hour), this error in Event Viewer:
The driver detected a controller error on \Device\Ide\IdePort0.
Looking at the Event Viewer, this error happened on 26-Feb, 28-Feb,2-Mar; I recovered the windows using 6-Mar image on 8-Mar.
Would this be the cause of the problem?

Similar Messages

Thunderbolt display has stopped working with my mac mini

I purchased a brand new thunderbolt display and mac mini a couple of months ago, and now the thunderbolt display no longer comes on when I start the mac (I am only able to type this here because I pulled out my old monitor and plugged it in to the mac mini via hdmi port, which seems to work just fine).
I have so far shut down and re start my mac a couple of times. I have unplugged everything and started them back up a couple of times, but nothing seems to work. How can I get this fixed? I have to admit that I feel like a shmuck for paying this much money for a monitor and then have it stop working.

If you haven't done so already, try resetting the printing system.
OS X Mavericks: Reset the printing system also Yosemite
Is the printer attached to the computer or is it a network printer?

Is it better to update the ipad with a mac mini vs a windows PC?

I have an iPad 2 which i want to update to iOS 6.1.3 (from 4.3.3). I usually sync it with a mac mini running Snow Leopard 10.6.4 with iTunes 10 which will not allow me to update the iPad as iTunes 11 requires OS X 10.6.8. I am not in a position to update my mac mini.
1) Can I use a PC running windows 7 with latest iTunes to update my iPad without any problems ?
2) Will I be able to sync my updated iPad with my mac mini running iTunes 10 on OS X 10.6.4 ?
Thanks for your inputs.

If you have an iPad 1, the max iOS is 5.1.1. For newer iPads, the current iOS is 6.1.3. The Settings>General>Software Update only appears if you have iOS 5.0 or higher currently installed.
iOS 5: Updating your device to iOS 5 or Later
http://support.apple.com/kb/HT4972
How to install iOS 6
http://www.macworld.com/article/2010061/hands-on-with-ios-6-installation.html
iOS: How to update your iPhone, iPad, or iPod touch
http://support.apple.com/kb/HT4623
If you are currently running an iOS lower than 5.0, connect the iPad to the computer, open iTunes. Then select the iPad under the Devices heading on the left, click on the Summary tab and then click on Check for Update.
Tip - If connected to your computer, you may need to disable your firewall and anitvirus software temporarily. Then download and install the iOS update. Be sure and backup your iPad before the iOS update. After you update an iPad (except iPad 1) to iOS 6.x, the next update can be installed via wifi (i.e., not connected to your computer).
Tip 2 - If you're updating via wifi, place your iPad close to your router to preclude getting a corrupted download.
 Cheers, Tom

Windows 2k server i want to replace with a mac mini running server

have a windows 2k server i want to replace with a mac mini running server 10.4.7
i basically want to port the settings and accounts from the 2 k running crap entourage to mac mail or keiro .
does anyone have a good way to do this or know of resources
i want all the accounts to stay active and will set up the same setting for the mini to runt he same services the old 2 k box was doing .
just some file sharing and mail services .
thanks
Mac OS X (10.4.8)

Look just to the right at "More Like This"
You might also check at > Korg Support

Is there a USB 3.0 Hub that really works with the Mac Mini?

My Mac Mini's four USB 3.0 ports work fine with my four USB Seagate GoFlex 3.0 hard drives. The drives mount at startup, and perform at expected USB 3.0 speeds. But, when I connect the drives to a USB 3.0 HUB to free up the Mac's USB ports for other devices, typically two of the USB Seagate drives will mount at startup, but two won't. There's a fix for this: after startup, I simply disconnect AC power from the drives that didn't mount, and reconnect the power a few seconds later. Now all my drives are mounted, they perform properly, and other USB devices connected to other Mac Mini USB ports (a mouse, a USB midi interface) work just fine as well. It's annoying, though, to have to perform this extra disconnect-reconnect step every time. I've tried two different USB 3.0 HUBs -- one from Uspeed and one from Satechi -- and I have exactly the same problem with both. Question: Is anybody else experiencing the same thing with a late 2012 Mac Mini and a USB 3.0 Hub? Has anybody found a 3.0 Hub that doesn't have this issue with the Mac Mini?

The USB 3.0 hub instability problems extend beyond the Mac-Mini, as addressed below.
At long last we're seeing progress in getting 2012 Macs to work with USB 3.0 hubs. As discussed on this and other discussion groups I've had a horrible time with my MacBook Pro Retina being unstable with USB 3.0 hubs. I know many of you have also or you wouldn't be reading this posting.
In June 2012 I bought one of the first 2012 MacBook Pro's with a Retina display. It's been a battle since with Apple selling what appears to be an incompatible or unstable system to effectively communicate with the USB 3.0 hubs. You'll see vendors now making comments that Apple is the source of the problem.
I've been through USB 3.0 issues with two MacBook Pro Retina laptops. I've also tested a Uspeed hub, with 3 portable USB 3.0 drives connected, at the Apple Store. This was on a newer model MacBook Pro Retina, and also on a 27" iMac. All had instances where drives failed to mount during the short period allowed for testing. (Because of time constraints, we were unable to test at the Store for spontaneous and unprovoked unmounting of drives connected to the hub. These problems have existed since the beginning on my rMBP.)
I am now on my 20th hub that has been purchased, or provided for testing. They varied from 4-Port to 10-Port powered hubs and involved 11 brand names. Comments were posted on Amazon, Tiger, and others for most of the ones purchased, and some that were tested. Some, like the HooToo specifically warned against use with Macs in the manufacturer's manual and, as I learned, for good reason. That was reflected in my comments for the drive on Amazon.
The Plugable 7-Port USB 3.0 powered aluminum-finish hub that I have been testing since October 13 was provided by Plugable after the first one, purchased through Amazon, was returned as unreliable. This 3rd, and newer generation Plugable hub uses the VIA VL812 chipset with the new version 90.81 firmware. My experience over the last 4+ weeks with this hub has been solid. While there have been problems with Eject errors, none were traced to the hub electronics. (Problems with intermittent connections at the cable connectors appeared to be the cause of the disconnect errors. Almost all of the failures were traced to intermittent Micro-B connectors, but that's another story.)
In addition to the greatly improved reliability of this hub, I find several features of this Plugable to be a plus including:
The plug engages fully to the "hilt" when plugged into the hub giving a solid connection, as occurs on the MacBook Pro Retina USB 3.0 ports. Others hubs typically had a gap between the "hilt" of the connecting end, and the hub allowing for lateral movement. With some hubs this allowed for intermittent connections if the cable was disturbed.
The on/off switch on the hub allows the hub to be powered down when not in use.
The full size Type-B connectors on the cable at the hub end engage solidly. Hubs with Micro-B connectors have presented intermittent connections in the cable connector.
The aluminum case looks attractive with Macs, IMO, but not a reason to buy.
Overall, Plugable's support is the best I've encountered. I've found their response to questions to be prompt and thorough. This, coupled with their online support articles has put them at the top of my list. They provide news and information that I've not found with other hub vendors.
The article titled "Plugable USB 3.0 7 Port Hub Firmware History" at the below link gives insight into the history of the problems that we've been having with the USB 3.0 hubs on Macs and the firmware updates, regardless of the brand of hub you have. Apparently, if you have the VIA VL 812 chipset, firmware version 85.81, you're in safe territory.
http://plugable.com/2013/10/30/plugable-usb-3-0-hub-firmware-upgrades2
(One of the Plugable hubs appears identical to the black 7-Port Uspeed hub, and both use the VIA VL 812 chipset. They appear to be from the same manufacturer with the real difference appearing to be in the VL812 version of the firmware in the hub.)
Some of the firmware can be upgraded, and some can't. Contact Plugable or Anker if you're affected.
Uspeed has made improvements, but they were still unstable as of the last one I received for testing. In her last reply on 10/13/13 Sunnie with AnkerDirect Customer Support stated:
Unfortunately, the new Firmware version (908x) does not work with the model "68UNHUB-B7U" you have. The hub bellow has much less complaints about Mac issue. We suggest that you order this one.
http://www.amazon.com/gp/product/B009Z9M3DY
AnkerDirect Customer Support
Note that the above hub recommended by Anker has an 8th port just for charging iOS devices. Some will see this as a plus. However, the lack of such a port is not seen as a big problem. It's easy and relatively inexpensive to purchase extra 5V power adapters for charging, which is my preference. Plugging and unplugging devices on a hub that is powered "On" presents the potential for movement of the cables. This could interrupt a cable connection and disconnect a drive during data transfer resulting in corrupted files. With 7 and 10 port hubs, and all the cables needed, this gets risky.
I believe the USB 3.0 hub issues we're having are the result of poor design of the Mac's USB 3.0 implementation at the start. Unstable hubs that I've had a friend with Windows 7 test, said they "performed like a dream" on his PCs. This indicates the problem is with Macs, not the (twenty) hubs I've used.
A statement from a support person dealing with USB 3.0 hubs tells what's I've long suspected: " -- the evidence is pointing to something specific to the Apple design (perhaps external to the chipset, like the signal re-driver….."
If you're having USB 3.0 problems, be sure to let Apple know by sending in a Feedback comment to Apple at:
http://www.apple.com/feedback/
I'm told they read and treat the feedback seriously (although the duration of this USB 3.0 problem makes me wonder if Mavericks and iOS 7 haven't had a higher priority and distracted from this. Microsoft got USB 3.0 right, how about it Apple?)

When I replaced my PC desktop with a Mac Mini and hooked up my HP printer to it, I discovered my other computers on the Wi-Fi network could no longer access the printer. The manual says Maverick OS will not allow PC's to access the printer. Any thoughts?

When I replaced my PC desktop with a Mac Mini and hooked up my HP printer to it, I discovered that my other computers on the Wi-Fi network could no longer access the printer. The manual says Maverick OS will not allow PC's to share the printer. Does anyone else have this problem? My printer does not have on-board Wi-Fi but, otherwise, works fine. I shouldn't have to buy a new one. Is there a OS patch out there that would open the printer port for my PC computers?

I'm assuming that on the Mac, the System Preferences -> Sharing -> Printer Sharing -> [X] HP printer -> Everyone can print is selected? That is to say, the Mac will allow anyone to print using the printer, and that you did not try to restrict who can print.
How is your network configured? Bonjour as a protocol will NOT cross a router boundary. If you have 2 or more subnets active with the PCs on one subnet and the Mac on another, that would block the PCs from seeing the Mac.
You could have multiple subnets if you have more than one router, such as an ISP provided broadband modem/router and another WiFi Router. If the PCs are talking to one router and the Mac is talking to another, that could be a 2 subnet situation. The additional routers must be put into bridge mode, which is done differently depending on the router. But the basics are to diable DHCP and NAT services on the secondary router(s) having just one active router on the network.
Also, using Bonjour Browser on my Mac, it is showing me that the printer is being advertised as using Internet Printing Protocol, so if that is something selectable on Windows, maybe you can bypass Bonjour on Windows.

Can I install windows home server 2011 on a mac mini?

Hey guys and girls...
Can I install windows home server 2011 on a mac mini? If so how?

WHS is 64-bit. Genius are really not versed in Boot Camp or Windows, let alone anything not on the "approved" list of Windows versions.
Most of the problems are with burning ISO, or the SuperDrive. It should have seen the NTFS partition. Disk Utility is known to be trouble, burning it on your Mac Mine but iwth Windows 7....?
Seeing you have Windows 7, format the partition to NTFS 160GB you want and then exit and boot WHS installer.
Or run the install from Windows 7.
In past, WHS supported TimeMachine, streaming video, supported iTunes (that was broken/disabled it seems by Apple with 10.0), as well as even SuperDuper backups.
Main idea is to have some network attached drives.
Netgear ReadyNAS Ultra2 Review
Newegg - HP StorageWorks X310 Windows Home Server
I have both a ISO and Burned it to a dvd useing windows 7 built in ISO burning software, Its a 64 bit copy (got from microsoft download website from my dads microsoft account).
It is enouth for the OS but it runs slowish on the mac mini (latest core 2 duo 2.4ghz model) The Idea was to have it backup my pc and laptop to a usb drive and act as a media centre pc (connected to av receaver and tv and on a gigabit network with a 2TB nas)
Since it looks like this may not work, whats the best way to make it into a media centure? mac osx? windows 7? plex? whats best and good?
I'd avoid USB like the plague. Why not use your PC instead? If I was going to use a Mini for WHS, I'd just use the Mini solely for Windows and not have OS X (you can boot OS X off an external drive anyway).

How to install windows xp on bootcamp on new Mac mini?

How can i install windows xp on bootcamp on new Mac mini?
I know that i should get an external usb optical drive, but buying such hardware for one use is a waste of money. Is there any other method?
I currently own a MacBook white, and really like the configuration. I it possible to copy the image of bootcamp to new mac mini? If so, what will happen to hardware and drivers?

Admiralali wrote:
Let me get this right:
1- copy the exact image of the winxp installation dc to USB
2- start bootcamp assistant, go through everything, till rebooting
3- boot from USB (hold ALT and select the USB volume)
4- go through winxp setup and done!
Am I missing anything?
I think that USB would be readable only on Mac os or winxp, but will the winxp installer read from USB?
Correct me if wrong.
Having read further websites, I am now a bit more dubious you can do this, at least with an XP installer.
However if you have a USB memory stick and an existing Windows computer (even a Boot Camp one) or can borrow one you could try using the free WinToFlash utility to make a supposedly bootable USB memory stick of the installer. See http://wintoflash.com/overview/en/
The problem is XP predates EFI firmare and XP only really knows BIOS firmware. As such (supposedly) XP would have problems booting from a USB device fully - it might lose connection part way through. Windows Vista and 7 do support EFI firmware.
The other approach I mentioned of temporarily moving the hard disk from the Mini to the MacBook so you can use the MacBook internal CD/DVD drive would work - be careful of the cables. Fortunately a new Mac mini and an old MacBook are two of the easier models to get at the hard disk. See http://www.ifixit.com/Guide/MacBook-Core-2-Duo-Hard-Drive-Replacement/514/1 (they also list other MacBook models) and http://www.ifixit.com/Guide/Installing-Mac-Mini-Mid-2011-Hard-Drive-Replacement/ 6422/1
Regardless of which method you try, the first step would be on the Mac mini to run Boot Camp Assistant and to create the partition for Windows. Then via either method try booting from a Windows XP installer.
As I have taken Macs apart many times, I personally might go the swapping the hard disk over route.

Install Windows 7 on a Mid 2010 Mac mini using USB or SD media?

Is is possible to install Windows 7 on a Mid 2010 Mac mini using USB or SD media? I have not figured this out. Here's what I have observed:
I can install OS X Lion using USB or SD media. Both are detected in the boot menu, and will boot.
An SD card with Windows 7 installation files formatted MBR/FAT32 using diskpart appears (with an SD card icon) in the boot menu but when selected as a boot device, the boot fails and the existing OS X instance on the Macintosh HD starts. A USB stick formatted as described does not appear in th boot menu at all.
An SD card or a USB stick formatted as described will boot on a Mid 2011 MacBook Air, and can be used to install Windows 7.
Is this due to EFI differences between a Mid 2010 Mac mini and a Mid 2011 MacBook Air?
Thanks.

The Mac Mini Mid 2010 has a DVD player built in, you can startup and install from a Windows 7 DVD. The Mac Mini Mid 2011 does not have a DVD player built in. I am happy that in new computers I can make use of an USB-stick to install Windows 7. Windows 7 uses MBR and Mac OS X uses EFI and that is why it was not possible on a Mac Mini Mid 2010. I think the EFI on a Mac Mini Mid 2011 is different.
I should like a firmware update on my Mac Mini Mid 2010 if possible. In that case I could choose between DVD or USB stick if I want to install Windows 7.
I also have a FireWire CF Card Reader. I think it is not possible to install Windows 7 via FireWire too.
I do have an external USB HD with 2 partitions: Mac OS X 10.6.8 and Windows 7, but is is not possible to start up Windows 7 from the external HD. It is possible to start up Mac OS X 10.6.8 from the external HD on a Mac Mini Mid 2010.

Trying to install windows 7 64 bit on a mac mini

I'm trying to install windows 7 64 bit on a mac mini, via boot camp. Install hangs at about 10% while files are being loaded from windows disc. I'm using an LG USB 2.0 Super-Multi DVD Burner. What's the fix for this.

Check this out: Boot Camp- Macs that work with 64-bit editions of Microsoft Windows Vista and Windows 7

My Samsung Sync Master 225UW's camera (webcam) won't work with my Mac mini

Hi,
I need help making my monitor's webcam work with my Mac mini. I have Mac OS X 10.5. When the computer launches the screen turns on, everything's perfect but the webcam will not turn on when I launch Photo Booth or iChat....what should I do?

That camera doesn't work with my mac either (I'm using it right now with a g4 powerbook, but will try again with my new power mac coming in... though I doubt it will make a difference)
The 225UW is specially made for Windows Vista, and I wonder if it needs a mac driver for the camera or something. We may be S.O.L. I knew that was a possibility when I ordered this monitor. Oh well... pay yer money... take yer chances.

I have just switched from windows and bought myself a new mac mini, only had it a few weeks and already getting message not enough free space. Help, surely cant be out of space already

I have just switched from windows and bought myself a new mac mini, only had it a few weeks and already getting message not enough free space. Help, surely cant be out of space already

It sounds unlikely of course. But from your question it's hard to tell what might have filled your HDD. Are you constantly on file sharing or has filled the drive with movies?
Best way to tell is to start checking what folders occupy space. "Get Info" for the HDD and its subfolders is a way to start checking where the data in question resides.
And as BGreg say, call Apple support is also a good way to begin with.

Windows 7 No 5GHZ WiFi on Mac Mini A1347 2010 Model using BootCamp

I have a new 2010 model mac mini and the WiFi in snow leopard works fine with both a 2.4GHZ and a 5GHz connection. When I reboot into Windows 7 I am only able to use a 2.4GHz connection and the 5GHz connection does not even show up as an option to connect to.
Any ideas?
- Dan

Welcome to the Apple Discussions!
Just an idea for you. There is an entire Apple Discussion forum dedicated to Boot Camp and Windows.
Whereas, not everyone here with an Mac mini has installed, tried to install or has experience with BC & Windows, everyone there has or at least has an interest. You may attract help more quickly there.
The Forums are at the bottom of the main Apple Discussions page under Windows Compatible Technology. Here is a link;
Boot Camp: Installation and Storage
Dah•veed

I have a problem with my Mac Mini. I dont remember my user password. How can i retreive it?

I have a problem with my Mac Mini. I dont remember my user password. How can i retreive it?

Mac OS X 10.6 Help- If you forget your administrator password
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
When the menubar appears select Terminal from the Utilities menu. Enter resetpassword at the prompt and press RETURN. Follow instructions in the dialog window that will appear.
Or see Reset a Mac OS X 10.7 Lion Password and OS X Lion- Apple ID can be used to reset your user account password.

Great experience with new Mac Mini!

I bought a 2.0Ghz Mac Mini a couple of days ago. I'm very pleased with it's performance and adding 2GB Ram doesn't hurt
I can't believe the grunt this little baby can give, it's outstanding. I thought that my old G4 1,33 was a champion, this one is so much better! I have installed VMware fusion it runs WinXP great, for my needs anyway. I'll try Bootcamp soon. Anyway, I love Leopard! There are some things getting used to like the new finder and how mounted SMB shares are presented but I'll get used to it for sure.
Love it!
Oops...gotta update my signature...done!

To echo the above: I've been delighted with my mini (a humble 'ole G4) since "migrating" from Windows just under three years ago.
The best compliment I can pay my mini and Apple in general is that it 'just works' as the "switcher" ads said at that time when I was making the transition.
Although Apple are frequently upgrading and enhancing the range, the great thing is that you don't really feel "left behind" with the latest change. There's a great continuity through the products and, ultimately, I feel it is enough to be a Mac user if the machine/software does what one wants.
Having said that, I daren't visit my nearest Apple Shop to look at the latest Intel minis - I'll only end up wanting one!

Windows 7 periodically crashed with my Mac Mini since 1.5 months ago.

Similar Messages

Maybe you are looking for