Windows 7 x64 - Intermittent Ethernet Connection
I bought a brand new MacMini (2013) a few months ago.
I installed BootCamp with Windows 7 64bit Premium and the BootCamp 4.0 software suite.
All hardware and software work perfectly with one exception:
I will be on the web or gaming on line when, suddenly, my internet connection drops out.
Windows will let me run through the network connection diagnostics which will eventually re-enable my internet connection.
When I go back to the web or game online the problem happens again within hours, or sometimes even minutes, of the previous re-connection.
On the Mac side everything works fine and I have no connectivity issues at all.
I just bought another MacMini with the same exact setup and it too is doing the same thing.
Can anyone help?
Quote
I built up my system but it will not recognize any network connection.
Quote
I did this because the driver cd that came with the mono would not properly work.
Quote
I still cannot connect to the internet, I get a 651 error.
Could you be a little more elaborate, as your problem description is a little vague?
Are you talking about a 'wired' internet connection, to your onboard LAN port?
In what way exactly did the driver CD 'not work'?
And where do you see this '651 error'?
Similar Messages
-
IOS: AnyConnect 2.5.3055, Windows 7 x64 fails to connect to Webvpn on 2811
I am attempting to add SSLVPN to my 2811 and 2801 production routers. These devices currently run IOS 12.4(24)T4 ADV SECURITY images. I have succesfully configured the SSL VPN gateway via CCP. I can connect via web browser to https://2811IP/sslvpn, log in, and use the web portal. When I attempt to use the full tunnel AnyConnect client on Windows 7 x64 (I have nothing else to test with right now) I get the simple and vague error: "Connection attempt has failed." This error occurs before I would receive a prompt to provide credentials. It never prompts me. There is no further information such as timeout, certificate error, or anything like that.
running term mon and debug webvpn on the router produces only the following when the client attempts to connect:
002121: Oct 23 00:10:35.081: WV: sslvpn process rcvd context queue event
002122: Oct 23 00:10:35.085: WV: sslvpn process rcvd context queue event
002123: Oct 23 00:10:38.973: WV: sslvpn process rcvd context queue event
002124: Oct 23 00:10:38.977: WV: sslvpn process rcvd context queue event
002125: Oct 23 00:10:39.041: WV: sslvpn process rcvd context queue event
002126: Oct 23 00:10:39.041: WV: Entering APPL with Context: 0x47FE4C90,
Data buffer(buffer: 0x4732ABC0, data: 0x3F5BE498, len: 172,
offset: 0, domain: 0)
002127: Oct 23 00:10:39.041: WV: http request: /sslvpn with no cookie
002128: Oct 23 00:10:39.041: WV: Client side Chunk data written..
buffer=0x4732AA20 total_len=188 bytes=188 tcb=0x481CF0A8
I've tried adding a program exception for anyconnect to the windows firewall.
I've tried disabling the windows firewall.
I've tried connecting via different ISPs, both wired and cellular.
I've tried the previous release of AnyConnect for Windows.
The TP certificate on the device is self-signed and valid from 1/23/2006 to 12/31/2019. I am prompted to accept the cert when I client Select (Connect) in the client. After I click Accept on the certificate window the connection fails. If I wait a while (perhaps a minute) the following error pops up, but ONLY if I wait a while before clicking Accept:
"AnyConnect cannot confirm it is connected to your secure gateway. The local network may not be trustworthy. Please try another network"
What else can I check?Does the iPod work OK?
Does it charge when connect to the computer?
Does it appear in My Computer?
Look at the dock connector on the iPod. Compare with the iPod that does work/connect.
I suspect you have a 2G iPod. Those can only go to iOS 4.2.1
http://support.apple.com/kb/HT1353#iPod_touch_late2009
iPod touch (3rd generation)
iPod touch (3rd generation) features a 3.5-inch (diagonal) widescreen multi-touch display and 32 GB or 64 GB flash drive. You can browse the web with Safari and watch YouTube videos with Wi-Fi. You can also search, preview, and buy songs from the iTunes Wi-Fi Music Store on iPod touch.
The iPod touch (3rd generation) can be distinguished from iPod touch (2nd generation) by looking at the back of the device. In the text below the engraving, look for the model number. iPod touch (2nd generation) is model A1288, and iPod touch (3rd generation) is model A1318. -
Cannot get Windows 7 x64 laptop to connect to AIRONET 1140 WAP
I recently changed the configuration of my Aironet 1140 from WEP to WAP2-Enterprise to make it more secure. I am using the WAP as the radius server. After making the change I connected my Blackberry to the wap as well as a Samsung Chromebook. However when I tried to connect my HP laptop it is unable to connect. Watching from the Aironet's console I see that it is processing the association and windows ask me to enter my uid and password. When I do this I get an authentication error. I have tried several times adjusting parameters on windows but it always fails. Here is the configuration of the WAP:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap.acrtek-lab.com
logging rate-limit console 9
aaa new-model
aaa group server radius rad_eap
server 10.53.55.127 auth-port 1812 acct-port 1813
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login default local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
dot11 syslog
dot11 ssid Acrtek-WPA2
authentication open eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa
username XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
username XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
ssid Acrtek-WPA2
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption mode ciphers aes-ccm tkip
ssid Acrtek-WPA2
antenna gain 0
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server local
no authentication eapfast
no authentication mac
nas 10.53.55.127 key 7 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
user xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
radius-server attribute 32 include-in-access-req format %h
radius-server host 10.53.55.127 auth-port 1812 acct-port 1813 key 7 xxxxxxxxxxxxxxxxxxxxxxxxxxxx
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 0 4
end
Windows Configuration:
Details about network adapter diagnosis:
Network adapter Wireless Network Connection driver information:
Description . . . . . . . . . . : Broadcom 4313GN 802.11b/g/n 1x1 Wi-Fi Adapter
Manufacturer . . . . . . . . . : Broadcom
Provider . . . . . . . . . . . : Broadcom
Version . . . . . . . . . . . : 5.100.82.139
Inf File Name . . . . . . . . . : C:\Windows\INF\oem29.inf
Inf File Date . . . . . . . . . : Tuesday, September 18, 2012 5:42:34 PM
Section Name . . . . . . . . . : BCM43XNG2022_NT61
Hardware ID . . . . . . . . . . : pci\ven_14e4&dev_4727&subsys_1795103c
Instance Status Flags . . . . . : 0x180200a
Device Manager Status Code . . : 0
IfType . . . . . . . . . . . . : 71
Physical Media Type . . . . . . : 9
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
Information for connection being diagnosed
Interface GUID: 5bab8bfe-12d7-4e0c-a46b-efc490047802
Interface name: Broadcom 4313GN 802.11b/g/n 1x1 Wi-Fi Adapter
Interface type: Native WiFi
Profile: Acrtek-WPA2
SSID: Acrtek-WPA2
SSID length: 11
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Connection incident diagnosed
Auto Configuration ID: 2
Connection ID: 3
Connection status summary
Connection started at: 2012-09-18 14:49:56-586
Profile match: Success
Pre-Association: Success
Association: Success
Security and Authentication: Fail
List of visible access point(s): 43 item(s) total, 43 item(s) displayed
BSSID BSS Type PHY Signal(dB) Chnl/freq SSID
00-1C-10-07-38-76 Infra <unknown> -79 11 linksys
70-56-81-CB-A2-7D Infra <unknown> -55 10 MRB LLC
08-86-3B-95-3B-E1 Infra <unknown> -77 11 belkin.be1
C0-C1-C0-52-FD-5F Infra <unknown> -75 11 AquaDeer-guest
70-73-CB-BB-9D-43 Infra <unknown> -60 1 the ridge by apple
00-17-C5-A5-5A-73 Infra <unknown> -67 2 MsPub
00-22-B0-BA-C7-E6 Infra g -72 1 mercer
E0-91-F5-D6-DF-76 Infra <unknown> -78 1 Chick-Fil-A
04-C5-A4-80-FC-50 Infra <unknown> -38 4 (Unnamed Network)
C8-3A-35-5D-AE-18 Infra <unknown> -82 4 medialink
00-23-69-1B-73-C9 Infra g -78 6 Matt and Heather
94-44-52-68-24-2B Infra <unknown> -73 5 Belkin.442B
68-7F-74-7E-50-74 Infra g -77 6 sjslinksys
00-1D-7E-49-E2-65 Infra g -75 6 Cubs
00-12-17-4B-4E-0D Infra g -41 8 (Unnamed Network)
C0-C1-C0-E4-3F-55 Infra <unknown> -78 6 SG Roi
C0-C1-C0-66-9F-CA Infra <unknown> -75 7 Heliman
66-33-4B-E1-47-27 Infra <unknown> -80 8 Jenny lake's Guest Network
00-1C-DF-A4-59-FB Infra <unknown> -60 10 radiofinger
C0-C1-C0-52-FD-5E Infra <unknown> -76 11 AquaDeer
08-86-3B-61-B0-BC Infra <unknown> -76 11 belkin.0bc
00-23-69-00-52-20 Infra g -70 11 670term
58-6D-8F-24-FC-21 Infra <unknown> -80 11 Bluejay1
04-C5-A4-80-FC-50 Infra <unknown> -36 4 Acrtek-WPA2
70-73-CB-BB-B3-49 Infra <unknown> -73 1 LeWonderment Inc.
E6-51-E4-A6-B1-25 Ad hoc g -78 4 megahoc.v24
00-17-C5-A5-5A-A9 Infra <unknown> -79 5 Vivaces
00-23-69-B4-5D-3E Infra g -81 6 Tanda
D0-66-7B-06-C7-45 Infra <unknown> -81 7 SEC_LinkShare_e70ac7
00-24-7B-5D-65-FA Infra g -80 6 myqwest0953
60-33-4B-E1-47-27 Infra <unknown> -81 8 Jenny Lake
00-25-9C-23-73-A6 Infra g -80 1 milehigh
00-24-01-DC-A4-3F Infra <unknown> -81 3 newwoman
C4-3D-C7-83-CE-74 Infra <unknown> -85 3 Desilets
08-86-3B-25-A7-CE Infra <unknown> -86 11 belkin.7ce
00-18-39-78-8F-92 Infra g -88 11 paul landow
98-FC-11-6E-E7-52 Infra <unknown> -80 11 China
28-CF-DA-B1-5F-03 Infra <unknown> -78 1 DeSanti
00-15-6D-D6-04-47 Infra g -69 1 (Unnamed Network)
00-21-91-10-1A-05 Infra g -81 1 dlink
1C-7E-E5-30-AE-66 Infra <unknown> -79 5 dlink
00-15-FF-26-47-98 Infra <unknown> -85 10 Verizon MIFI4510L 4798 Secure
00-23-69-38-2C-D2 Infra <unknown> -82 1 linksys
Connection History
Information for Auto Configuration ID 3
List of visible networks: 41 item(s) total, 41 item(s) displayed
BSS Type PHY Security Signal(RSSI) Compatible SSID
Infra <unknown> No 22 Yes linksys
Infra <unknown> Yes 82 Yes MRB LLC
Infra <unknown> Yes 26 Yes belkin.be1
Infra <unknown> No 30 Yes AquaDeer-guest
Infra <unknown> Yes 76 Yes the ridge by apple
Infra <unknown> No 62 Yes MsPub
Infra g Yes 36 Yes mercer
Infra <unknown> Yes 24 Yes Chick-Fil-A
Infra <unknown> Yes 94 Yes (Unnamed Network)
Infra <unknown> Yes 16 Yes medialink
Infra g Yes 24 Yes Matt and Heather
Infra <unknown> Yes 34 Yes Belkin.442B
Infra g Yes 26 Yes sjslinksys
Infra g Yes 30 Yes Cubs
Infra g Yes 92 Yes (Unnamed Network)
Infra <unknown> Yes 24 Yes SG Roi
Infra <unknown> Yes 30 Yes Heliman
Infra <unknown> Yes 20 Yes Jenny lake's Guest Network
Infra <unknown> Yes 76 Yes radiofinger
Infra <unknown> Yes 28 Yes AquaDeer
Infra <unknown> Yes 28 Yes belkin.0bc
Infra g Yes 40 Yes 670term
Infra <unknown> Yes 20 Yes Bluejay1
Infra <unknown> Yes 95 Yes Acrtek-WPA2
Infra <unknown> Yes 34 Yes LeWonderment Inc.
Ad hoc g No 24 Yes megahoc.v24
Infra <unknown> No 22 Yes Vivaces
Infra g Yes 18 Yes Tanda
Infra <unknown> Yes 18 Yes SEC_LinkShare_e70ac7
Infra g Yes 20 Yes myqwest0953
Infra <unknown> Yes 18 Yes Jenny Lake
Infra g Yes 20 Yes milehigh
Infra <unknown> Yes 18 Yes newwoman
Infra <unknown> Yes 10 Yes Desilets
Infra <unknown> Yes 8 Yes belkin.7ce
Infra g Yes 4 Yes paul landow
Infra <unknown> Yes 20 Yes China
Infra <unknown> Yes 24 Yes DeSanti
Infra g No 50 Yes (Unnamed Network)
Infra g No 22 Yes dlink
Infra <unknown> Yes 10 Yes Verizon MIFI4510L 4798 Secure
List of preferred networks: 5 item(s)
Profile: Acrtek-WPA2
SSID: Acrtek-WPA2
SSID length: 11
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: Yes
Profile: ZRDD2
SSID: ZRDD2
SSID length: 5
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: No
Reason: 0x00028002
Profile: GMANNET
SSID: GMANNET
SSID length: 7
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: No
Reason: 0x00028002
Profile: Conference Rm
SSID: Conference Rm
SSID length: 13
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: No
Reason: 0x00028002
Profile: rntdnet
SSID: rntdnet
SSID length: 7
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: No
Reason: 0x00028002
Information for Connection ID 4
Connection started at: 2012-09-18 14:50:08-279
Auto Configuration ID: 3
Profile: Acrtek-WPA2
SSID: Acrtek-WPA2
SSID length: 11
Connection mode: Infra
Security: Yes
Pre-Association and Association
Connectivity settings provided by hardware manufacturer (IHV): Yes
Security settings provided by hardware manufacturer (IHV): No
Profile matches network requirements: Success
Pre-association status: Success
Association status: Success
Last AP: 04-c5-a4-80-fc-50
Security and Authentication
Configured security type: WPA2-802.1X
Configured encryption type: CCMP(AES)
802.1X protocol: Yes
Authentication mode: Invalid (5)
Number of 802.1X restarts: 1
Number of 802.1X failures: 0
Key exchange initiated: No
Number of security packets received: 2
Number of security packets sent: 1
Security attempt status: Success
Information for Auto Configuration ID 2
List of visible networks: 40 item(s) total, 40 item(s) displayed
BSS Type PHY Security Signal(RSSI) Compatible SSID
Infra <unknown> No 22 Yes linksys
Infra <unknown> Yes 85 Yes MRB LLC
Infra <unknown> Yes 22 Yes belkin.be1
Infra <unknown> No 32 Yes AquaDeer-guest
Infra <unknown> Yes 64 Yes the ridge by apple
Infra <unknown> No 74 Yes MsPub
Infra g Yes 60 Yes mercer
Infra <unknown> Yes 24 Yes Chick-Fil-A
Infra <unknown> Yes 86 Yes (Unnamed Network)
Infra <unknown> Yes 38 Yes medialink
Infra g Yes 36 Yes Matt and Heather
Infra <unknown> Yes 40 Yes Belkin.442B
Infra g Yes 62 Yes sjslinksys
Infra g Yes 30 Yes Cubs
Infra g Yes 95 Yes (Unnamed Network)
Infra <unknown> Yes 24 Yes SG Roi
Infra <unknown> Yes 28 Yes Heliman
Infra <unknown> Yes 20 Yes Jenny lake's Guest Network
Infra <unknown> Yes 81 Yes radiofinger
Infra <unknown> Yes 10 Yes AquaDeer
Infra <unknown> Yes 32
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Auto Configuration
Initialize status: Success
Information for connection being diagnosed
Interface GUID: 5bab8bfe-12d7-4e0c-a46b-efc490047802
Interface name: Broadcom 4313GN 802.11b/g/n 1x1 Wi-Fi Adapter
Interface type: Native WiFi
Profile: Acrtek-WPA2
SSID: Acrtek-WPA2
SSID length: 11
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Result of diagnosis: Problem found
Issue referred to: L2Sec Helper Class
Root cause:
Windows could not connect to "Acrtek-WPA2"
You can try to connect again.
Repair option:
Reset your wireless network adapter
This will disable and then enable the network adapter "Wireless Network Connection" on this computer.
Diagnostics Information (L2sec Helper Class)
Details about L2Sec Helper Class diagnosis:
For complete information about this session see the Wireless Diagnostic Informational Event.
Helper Class: Layer2 Security
Initialize Status: Success
Result of diagnosis: Problem found
Issue referred to: EAP Helper Class
Root cause (EAP):
Network authentication failed\nWindows doesn't have the required authentication method to connect to this network.
Detailed root cause:
EAP failed
Workaround for hypothesis: Contact the network administrator for "Acrtek-WPA2"
EAP workaround: Contact your network administrator\nWindows needs to be configured to use the authentication method required for this network.
Information for connection being diagnosed
Interface GUID: {5bab8bfe-12d7-4e0c-a46b-efc490047802}
Interface name: Broadcom 4313GN 802.11b/g/n 1x1 Wi-Fi Adapter
Interface type: Native WiFi
Profile: Acrtek-WPA2
SSID: Acrtek-WPA2
SSID length: 11
Connection mode: Infra
Security enabled: Yes
Connection ID: 3
Security settings provided by hardware manufacturer (IHV): No
Profile matches network requirements: Yes
Pre-Association and association status: Success
Security and Authentication:
Configured security type: Robust Secure Network (RSN / WPA2) with 802.1X
Configured Encryption type: CCMP (AES)
Security connect status: Fail 0x00050005
Number of security packets received: 4
Number of security packets sent: 3
802.1X protocol: Yes
Authentication Identity: User only
IAS Server engaged: Yes
EAP Method supported by IAS Server: Unknown
EAP type: 25
EAP Error: 0x40420016
Number of 802.1X restarts: 1
Number of 802.1X failures: 1
802.1X status: Fail 0x00050005
Key exchange initiated: No
Unicast keys received: No
Multicast keys received: No
Network Diagnostics Log
File Name: A20D3467-8AD4-483E-91F4-9EC5E18AA1F9.Diagnose.0.etl
Other Networking Configuration and Logs
File Name: NetworkConfiguration.cab
Collection information
Computer Name: ACCRETIVE-SW
Windows Version: 6.1
Architecture: amd64
Time: Tuesday, September 18, 2012 2:50:09 PM
Any help would be greatly appreciated.Hello Mr. Wells,
Thank you for your question.
However, the Small Business Support Community is limited to Cisco Small Business Products, and the Aironet products are considered as a Enterprise level devices.
I recommend you to post this question on the on the correct forum, in order to get a better response.
You can move your post using the Actions panel on the right.
Best regards,
Diego Rodriguez
Cisco Small Business Community Engineer -
Bootcamp windows 7 x64 Ethernet controller error...
I've installed the Windows 7 x64 drivers, yes I'm aware of how to get around the x64 error. However after installing My internet doesn't work.
Theres a few drivers with error code 28, saying they aren't installed next to them; ethernet controller, network controller. I've ran the repair utility, and it still doesn't install the files.
Any suggestions?Ok, I think this problem has been resolved, so I'll post the solution in case others with the Samsung Syncmaster 204B have the same problem. The answer was erasing the PRAM by holding Option-Command-P-R at boot up (http://support.apple.com/kb/ht1379).
This is what I think happened:
An update in Windows Update is available for the Syncmaster 204B, but wasn't visible when I first connected the Syncmaster. I wasn't able to see the update until I rebooted with the Syncmaster connected (after several crashes). After seeing the update in Windows Update under 'Optional Updates", called "Samsung - Display- 204T/204Ts/204B, Syncmaster Magic CX20Ts(digital)", I installed it, but bootcamp Windows continued to crash randomly after attaching the Syncmaster via both Mini Display Port-to-DVI and Mini Display Port-to-VGA. Sometimes it crashed after a few minutes, sometimes an hour, the same as before I installed the update.
I was convinced that it was a compatibility problem between Windows 7 x64, the Syncmaster 204B and the MacBook Pro 13" Mid-2010 hardware since this problem only happened when booting into bootcamp Windows 7 x64 (everything worked fine in Mac OS), but now that doesn't seem to be the case. I think the update fixed the problem, but after installing the update some of the of the original incompatible display settings remained resident in the Mac's PRAM. Erasing the PRAM cleared these settings and allowed the new updated settings to be loaded instead, fixing the crash issue.
-Scott -
Cannot configure and connect to Airport Express Base Station Model A1264 with Windows 7 (x64)
I am not able to connect Airport Express Base Station Model A1264 with Windows 7 (x64). I did a factory reset, uninstalled and reinstalled the AirPort Utility for Windows v. 5.6.1.
My objective is to extend a non-Apple WiFi network with Airport Express Base Station Model A1264 and use it for direct ethernet and/ or wireless connection. Any guidance as to how I can get set up here?This is very common, we run a mix of mac and various pc brand desktops and laptops, what I have found is that using the windows wireless client rather than manufacturers on some laptops helps, getting the latest wireless drivers from the manufacturer has helped, make sure all your windows updates XP and Vista are current.
If all the above is covered try the different WEP WPA WPA2 variants or even without for test purposes. I have most success with WPA2.
Finally I am assuming your running the latest firmware on the express unit, whilst this hasn't attributed to better connectivity for us I did it regardless.
Message was edited by: Fence Rider -
Connecting Time Capsule to a Windows 7 PC via Ethernet
Hi,
I have the following network configuration:
- Speedport (Deutsche Telekom AG) as DSL Router (I need that router for the IPTV)
- Connected to this router are two laptops and the Time capsule (WLAN)
Everything is working fine. However, I try now for days to connect my Windows 7 PC via Ethernet to this network via the Time Capsule. Due to location it is not possible to connect the Windows 7 PC directly to DSL Router or to connect the Time Capsule by cable to the router.
I think I tried every possible configuariton but without any improvements. Does anyone have an Idea what I can do ???
Windows is always telling "no identified network" and it always shows a park bench
Hope anyone have an idea ! Thanx for your help
TC - Firmware: 7.4.2try http://www.microsoft.com/mac/remote-desktop-client
Allan -
WMP600N - weak connection and low signal - Windows 7 x64
I bought the WMP600N because Linksys and Microsoft listed it as 'compatible' for Windows 7 x64.
My experience:
- unstable and weak connection
- pings to websites like google.com drops, average: 1 out of 3
- low signal, on the same spot my three years old HP-laptop with 'a build in wireless card' has full signal strength in Windows 7
- it works well under Windows XP (32 bit)
I'am convinced that drivers for the WMP600N are not ready for Window 7 x64. Linksys (or Ralink, which developed the chipset), please release a proper driver for the WMP600N!
Message Edited by Storm_dutch on 12-20-2009 09:51 AM
Message Edited by Storm_dutch on 12-20-2009 09:52 AMI'm not sure about you guys, but I use WMP600N and running Windows 7 64bit without any issues. The driver that I'm using now is Driver Version: 3.0.2.0, Driver Provider: Ralink Techonolgy Corp, Driver Date: 6/19/2009. Here's what I did when I upgrded my wireless adapter. 1. Uninstall the original wireless driver from device manager. 2. Turn off the computer and phisically removed the wireless adapter from my computer. 3. Pop in the new WMP600N and turn on the computer. 4. Windows 7 then automatically detects the new adapter and intall the proper driver for it. Well, that's all I did. The whole process is very simple and straight forward.
-
I recently added a new printer to a 2005 vintage PC that is running windows 7. It used to go through a router in my wifes upstairs office to the time capsule by wired ethernet (cat5) but when I added her new local printer thought I would network it, big mistaked, lost all my ethernet connection and she cannot get to the internet. Wireless not an option. How do i set up again the ethernet connection and i will only USB the printer locally this time for the windows pc?
Tried windows diagnostics, and besides telling me to reset everything and turn router off and on etc. I am in an endless loop.
Other Mac products are not impacted by this issue.I see no direct connection.. a printer and the computer setup for internet are not related.
But it sounds like the router in the wife's office is now in the wrong mode..
If you have an existing main router replace the second router for a switch .. that is the easy way.
Otherwise you need to bridge the router if it has that option.. most do not. Or use wan bypass.. where you turn off the dhcp server in the router and fix its ip to match the range of the main router.. this is the hassle of using router as a switch.
BUT I am making a huge number of assumptions.
What I need is the full network layout.. a quick picture would help.
I need main modem.. main router.. (maybe same box or different).. make model and current IP address and how dhcp is setup.
I need secondary router.. if that is what it is, IP and settings.
I want the printer type and model. How it is connected.
BTW I much prefer to see a network printer plugged into the network rather than usb.. it is only a matter of sorting the IP settings and driver pointing to the network rather than local.
Or you should think of it as a broken washing machine and call the technician.. who could fix the whole lot in an hour. -
Windows 7 x64 - iTunes no longer auto launches when I connect iPhone
Hi
Ok so i installed Windows 7 x64 and iTunes x64 but now iTunes no longer auto-launches when I connect my iPhone. My PC has no problems finding my iPhone, it does the camera bit and if I start iTunes manually it syncs the iPhone with no issues.
Does anyone know how I can get iTunes to auto launch again please?+it does the camera bit+
I dont' think it's supposed to be doing this.
Maybe mindspan's post here will help you
http://discussions.apple.com/message.jspa?messageID=8119647#8119647 -
Please god . deactivate this product. Your troubleshooters dont work, cannot deactivate. I am using RETAIL, adobe acrobat xi.Connected to internet. On for over 20 min. Open to deactivate greyed out. Windows 7 x64 pro. This crap makes people want to use fraud. I just want it OFF do i can USE it on another COMPUTER.
can anyone in customer support deactivate this??Hi Terry,
I have checked the serial number and found that you have sufficient activation count left to install it on 2 computers.
Please uninstall the software and activate it on the other machine. In case of issues please let me know and I will help you.
Here is my direct email: [email protected]
Chat Support email:
http://helpx.adobe.com/x-productkb/global/service1.html
Regards,
Rave -
Unable to connect to localhost Windows 7 x64, CF9 x64
I've been following along with the Lynda.com tutorial on ColdFusion Builder. Everything went smoothly until the part where I'm supposed to attach CFB to the localhost. The Lynda.com presenter is on a Mac. I am running 64-bit Windows 7 and 64-bit ColdFusion 9 developer edition.
When I would add the local server to CFB, it would sit with status unknown forever. Eventually I would get a message on the console saying
Error retrieving server version. Cannot perform the operation. Check if the server is accessible from web browser.
(I was following the thread about remote connection issues with great interest, but nothing there seemed to apply to my problem.)
I have tried a number of different permutations of installing and configuring the components.
CF9 x64 Stand-alone
CF9 x64 J2EE piggybacking on IIS
CF9 x64 J2EE built-in web server
I tried these with and without the most recent patches to CFB and CF9
With the built-in web server, I tried using cfusion:8300. I also tried creating a new server instance called localhost on 8500. When I tried adding localhost:8500 to CFB, CFB locked up.
I have a feeling that I'm either looking in the wrong place or I have overlooked something obvious. I just thought of one thing I haven't tried... I will try to install the 32 bit version of CF9 to see if that helps.
Any other advice would be appreciated. Is anyone else running CF9 x64 under Windows 7 x64?
--BI decided to check the system reqs for CFB just in case I made an RTFM gaffe.
http://www.adobe.com/cfusion/tdrc/index.cfm?product=coldfusion_builder
ColdFusion Builder for Windows
* 2GHz or faster processor
* Microsoft® Windows® XP with Service Pack 3, Windows Vista® Ultimate or Enterprise (32 or 64 bit running in 32-bit mode), Windows Server® 2008 (32 bit), or Windows 7 (32 or 64 bit running in 32-bit mode)
* 1GB of RAM (2GB recommended)
* 1GB of available hard-disk space
* Java™ Virtual Machine (32 bit): IBM® JRE 1.5, Sun™ JRE 1.5, IBM JRE 1.6, or Sun JRE 1.6
* DVD-ROM drive
* Eclipse 3.4.2 or Eclipse 3.5 32-bit (for plug-in installation)
So, no 64 bit version, but the 32-bit should work... well - that's one less thing.
I tried 32bit CF9 but the server wouldn't serve any pages. I kept getting a 500.0 error. Adobe has addressed this:
http://blogs.adobe.com/vikaschandran/2010/07/08/altering-application-pools-in-iis-764-bit- to-create-32-and-64-bit-connectors-with-coldfusion-964-bit/
but I decided to shut down IIS and run CF9 as a free-standing J2EE using its own built-in web server.
Once again, CFB locked up when trying to add the new localhost server. I'm going to uninstall and reinstall CFB... -
ThinkPad W530 with Windows 8 x64 Pro BSOD when connecting to projector
Nine, that only covers Widows 7. Many people in this thread have reported the problem using Windows 8. Has that been addressed by Lenovo yet? Stability problems like this should NEVER be allowed to go so long without a resolution.
Edit Note : This thread was created base from the previous thread "ThinkPad W530 with Windows 7 x64 Pro BSOD when connecting to projector. As we currently Cx reporting facing the same issue on Win8 I have seperated this thread in order not toconfuse other customer. For cutomers facing this issue please continue posting in this thread.Hi shan_mcarthur,
Thanks for posting. I read through this thread again and noticed that most of customers here do indeed have Windows 7 installed as what the title represented unless I'm mistaken or may have missed out are you or anyone else here facing the same issue on Windows 8. If that is the case I'll be more than happy to bring this up with the teams but it will have to be a new thread though as I'd like to keep the resolution separate based on the OS use just to not confuse other customer .
For those facing the same issue above on Win8, please do let me know so we can start a discussion around this.
Do let me know.
Regards -
AnyConnect client 3.1.04063 Windows 7 x64 users cannot make ssl connection
Over the past week several of my users have suddenly found they cannot connect with a previously working client. After the login banner is accepted they all get an error message "The certificate on the secure gateway is invalid. A VPN connection will not be established." Then another message "AnyConnect was not able to establish a conenction to the specified secure gateway. Please try connecting again." On the ASA 5540 logs I see successful authentication and then the device is trying to establish a ssl session which is denied and then connection is terminated.
I have verfied that the ssl certificates are valid and are installed in the trusted root certificates location. I have checked that ICS is disabled. I have checked that the vpn adapter display name is correct.
Does anyone have any ideas?We are not using a self signed cert. We have a cert issued by the DoD. It seems like a user who had previously connected and is on Windows 7 x64 will not be able to connect. Users who have never connected and browse to the site will be able to successfully connect.
Additional information: I have cleared all DoD related certs and the server cert from the certmgr.msc on an affected Windows box. Uninstalled the AnyConnect application and all remnant files. Cleared SSL cache on both IE and Firefox browsers. I rebooted then tried connecting via the web address but am receiving the same issue. -
VPN error "all devices connected" suddenly appears on Windows 7 x64
I have been having VPN issue on one Windows 7 x64 Dell Latitude laptop in the past couple of weeks. The symptom was that the VPN would connect fine and work for a few hours. Then the connection would become unusable even though status of the
VPN connection would shown as connected. No connection could be made to machines on the VPN and the VPN connection could not be disconnected. Restarting the computer would usually resolve the issue. This morning however VPN stopped working completely.
I got the error 619 with the message "all devices connected". Rebooting the machine did not help and neither did deleting and recreating the VPN connection.
Even more strangely every operation related to VPN has become extremely slow. When connection attempt is made, it takes a while for the Connect VPN Connection dialogue window to show up and the connection attempt itself takes minutes before the error
message shows up. It also takes a long time just to bring up the property dialogue of the VPN connection and switching between tabs takes a few seconds as well.
The VPN connection is set up using all default values and other machines no the network do not have this problem. As far as I know except for the routine windows update no network related changes or software installation was done to this box before or during
the time that the problem started to surface.
I created a second user account on this machine and was able to get a new VPN connection to work briefly. However after logging off/on the same problem occurred for the 2nd user as well.
Has anybody experienced similar issues? TIA!Hi,
Have you tried any other method to resolve this problem, such upgrade or reinstall NIC driver?
Firewalls and antivirus programs may be running that block access to the VPN ports. Please temporarily disable these to troubleshoot.
If problem persists, please also perform the suggestions from the link below:
http://social.technet.microsoft.com/Forums/windows/en-US/32c5e5b5-b2a2-43d3-b702-9cd0c8ef2c67/windows-7-vpn-hangs-at-verifying-username-and-password?forum=w7itpronetworking
Roger Lu
TechNet Community Support -
Macbook/mac mini can ethernet connected[crossover] with another PC-windows?
macbook / mac mini can ethernet connected crossover with another PC - windows like Sony VAIO laptop VGN-A297XP CEZ ? If yes can share all services like pc-pc connection ? IF Ethernet speed is 100/1000 for this laptop what is connection speed mac-pc ?
If you temporarily connect the Mac Mini server to the Time Capsule (TC) by Ethernet, can it gain Internet access now? Is the Mac Mini in the same room, different room/floor from the TC?
Maybe you are looking for
-
Noise Saturation playing Demo Project
I'm a new user running Logic Pro 9.1.7 on a Mac Snow Leopard 10.6.8 platform with an Edirol UA 25EX - Sound Card and Behringer Truth B2031A speakers. I have a problem with heavy noise saturation playing the demo project, could anyone give me advice a
-
Is this offer a fake or why cannot change my abo?
Is this offer a fake or why cannot change my abo?
-
Why didnt my icloud back up my pictures
I had to restore my phone today & it didnt restore my pictures on icloud..they are very important photo's that i can not get back..please HELP!
-
I have CS6 but can't type the serial number in
I have CS6 and trying to load it on my new computer
-
I cannot open Google in Firefox. Why not??? This is since I "refreshed" Firefox.
Ever since I refreshed Firefox, I cannot open Google which means I cannot access my Gmail account. This is very aggravating. Kindly help me to fix this problem I have tried the usual restart solution and it didn't solve anything.