Windows 8.1 does not go to sleep reliably anymore

I recently did a clean install of Windows 8.1 Pro x64 (final version). Before doing the clean install, all hardware being identical, my Windows 8 was ran smoothly and went to sleep fine automatically after the set time.
Now, after the clean install, although I believe I have installed and set up everything as before, the computer does not reach standby automatically anymore most of the time. To be precise, when I reboot or log off and on the PC, the sleep functionality
is re-established for a while, but after 1 or 2 hours of work it invariably gets lost.
However, as soon as I disable the Ethernet adapter, the PC sleeps as expected.
I do not seem to be able to figure out why this is, or how my configuration is different than before.
Here are a few specs about my hardware: ASRock Z77E-ITX mainboard (http://www.asrock.com/mb/Intel/Z77E-ITX/, has the Windows 8.1 compatibility sticker), Intel Core i7-3770, 4x 3.40GHz including Intel HD 4000 integrated graphics (no external graphics installed),
Intel 530 Series SSD, Intel 520 Series SSD, WD HDD. I have use a wired Ethernet connection, my Ethernet chip is from Broadcom. Wifi chip is disabled.
Since this has been a pervasive issue with all Windows versions, the internet is full of suggestions how to resolve this matter. Why I am not convinced that the old advice still has any bearing as I tend to think Windows 8.1 introduced new issues (bugs?),
for the sake of covering all bases, I tried almost every tip I could find on the net and will list my fruitless attempts in the following. It might also be useful as reference for other people trying to tackle such issues.
1) Installed latest Windows 8.1 drivers from Asrock's homepage. I also tried chip manufacturer's like Intel's own drivers, did not make any difference (so far).
2) Left the homegroup and disabled homegroup functionality as for example in these threads it has been argued that this is a new issue with Windows 8.1: http://www.eightforums.com/general-support/28226-windows-8-1-refuses-sleep-2.html
http://www.eightforums.com/general-support/33221-windows-8-1-does-not-go-sleep-standby-automatically.html
3) In the Ethernet adapter's settings, I unchecked ipv6. I also made sure the device cannot be awaken through the network.
4) I even went so far to disable network discovery as
file and printer sharing (both in private and public profiles) and disable
public folders.
5) Even though sharing is disabled, I also made sure that within the energy options the computer is
allowed to sleep when sharing media.
6) powercfg /requests returns "none".
7) ran powercfg /energy duration 300 from an elevated command prompt while the ethernet adapter was enabled. It found 9 errors, mostly related to USB hubs, but the same errors were also recorded when I repeated the exercise having the ethernet
adapter disabled. So these errors are probably not relevant for the problem at hand.
8) powercfg /devicequery wake_armed : just the mouse and keyboard appear
9) I tried netstat which shows many connections but do not know how to interpret them or what to look for. Same for
Wireshark. If anybody can guide me on how to use these tools, I am happy to learn about it.
10) powercfg -requestsoverride DRIVER \FileSystem\srvnet SYSTEM
did not help, reverted it.
11) Uninstalled software some would find suspicious: Cisco Anyconnect VPN Client, Shadowprotect Desktop backup software, VMware player. Did not help.
12) I also have a MySQL server installed, which I did NOT uninstall because it would be too much point reinstalling and reconfiguring it. However, I doubt this is the culprit as with Windows 8 it did not prevent any sleep. Even when I stop the server the
PC does not go to sleep.
This is more or less it. I am out of ideas and welcome any feedback.
Again, when the Ethernet adapter is disabled, the PC sleeps as programmed, but I cannot figure out what communication is responsible for keeping it awake.
Thanks,
Steve

Hi Steve,
I don't know if you'll feel better but - You are not alone facing the same problems, I am sure that all the power handling in 8.1 is a mess. If I force the comp. to go to sleep mode, after a while it is
not staying in the sleep mode but shutting down autonomously. I suppose there is more hidden bugs.
Tazlam
Isn't your computer just switching from sleep mode to hibernation mode after the amount of time set in your power management settings? This sounds like it, as in hibernation the computer is effectively shut off. This is also intended behaviour.
As you guys, I hope MS releases a fix soon.

Similar Messages

Satellite P845t-10G does not go to sleep closing lid after Win 8.1 upgrade

Hi,
I own a P845t-10g and since I upgraded to Win 8.1 the laptop does not go to sleep (or shut down) when closing the lid.
However, when opening the lid, it wakes from sleep mode.
I tried installing latest Toshiba systems settings utility and all updates on the support site.
Any ideas how to fix this?
Thanks!

Did you check the option called: What closing the lid does?
Click on the 'Power Options' icon in taskbar (or in control panel).
Then click 'More power options'. Now a new windows will open. On the left side panel click on 'What closing the lid does'.
Now you will see two possible mode: battery and plugged in. For each mode you can set the action for closing the lid.
BUT one question: did you upgrade the Win 8.1 following the instruction from Toshiba?
http://www.toshiba.eu/innovation/generic/windows8_1-message/ Did you install all the Toshiba Windows 8.1 drivers and utilities in the right order!?

Macbook pro does not go to sleep when closing lid

Hi,
I'm having a weird problem with my macbook pro. When I close the lid, my macbook does not go to sleep. Even more weird: when I put my macbook to sleep using cmd + alt + the eject button or using the apple button => sleep, my macbook stops sleeping as soon as I close the lid
It seems like this problem occured after installing the Nosleep extension for mac (http://code.google.com/p/macosx-nosleep-extension/). I already deleted that program and rebooted, but that did not help.

Please read this whole message before doing anything.
I've tested these instructions only with the Safari web browser. If you use another browser, they may not work as described.
This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
These steps are to be taken while booted in “normal” mode, not in safe mode. If you’re now running in safe mode, reboot as usual before continuing.
Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
Some of the commands will line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then copy it. The headings “Step 1” and so on are not part of the commands.
Note: If you have more than one user account, Step 2 must be taken as an administrator. Ordinarily that would be the user created automatically when you booted the system for the first time. The other steps should be taken as the user who has the problem, if different. Most personal Macs have only one user, and in that case this paragraph doesn’t apply.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Step 1
Triple-click anywhere in the line of text below on this page to select it:
kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}' | open -ef
Copy the selected text to the Clipboard by pressing the key combination command-C. Then click anywhere in the Terminal window and paste (command-V). A TextEdit window will open with the output of the command. If the command produced no output, the window will be empty. Post the contents of the TextEdit window (not the Terminal window), if any — the text, please, not a screenshot. You can then close the TextEdit window. The title of the window doesn't matter, and you don't need to post that. No typing is involved in this step.
Step 2
Repeat with this line:
{ sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix\.cron)|org\.(amav|apac|cups|isc|ntp|postf|x)/{print $3}'; echo; sudo defaults read com.apple.loginwindow LoginHook; echo; sudo crontab -l; } 2> /dev/null | open -ef
This time you'll be prompted for your login password, which you do have to type. Nothing will be displayed when you type it. Type it carefully and then press return. You may get a one-time warning to be careful. Heed that warning, but don't post it. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
Note: If you don’t have a login password, you’ll need to set one before taking this step. If that’s not possible, skip to the next step.
Step 3
{ launchctl list | sed 1d | awk '!/0x|com\.apple|org\.(x|openbsd)/{print $3}'; echo; crontab -l 2> /dev/null; } | open -ef
Step 4
ls -A /e*/{cr,la,mach}* {,/}Lib*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts .la* 2> /dev/null | open -ef
Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
Step 5
osascript -e 'tell application "System Events" to get name of login items' | open -ef
Remember, steps 1-5 are all copy-and-paste — no typing, except your password. Also remember to post the output.
You can then quit Terminal.

TS4080 apple thunderbolt display image on display intermittently goes dark, does not wake from sleep after clicking mouse or keyboard, but there is "bonk" sound after clicking mouse or pressing keys. Rebooting by pressing the power button resolves issue.

My apple thunderbolt display (which I purchased 1.5 years ago; OS 10.7.5 Mac Mini) intermittently goes dark, does not wake from sleep after clicking mouse or keyboard, but there is "bonk" sound after clicking mouse or pressing keys, so am thinking it is a hardware problem with the display. Rebooting by pressing the power button turns the screen back on, but the same phenomenon has occurred several times. Could this be a software issue, or do I need to have my display repaired? Your feedback would be appreciated.

Hi ED, tough to tell, but it does sound like it's waking with the bonk, just not displaying.
Long shot but...
I wonder if it's a variation of this, of which I've seen many different symptoms...
Resolution
Move the mouse or trackpad cursor over the center area of the login window so you can see the user icons. Click on the icon of the user that you would like to login as, type in the user's password, and press Return.
If the login window is configured to show only the name and password fields, type in the user's name and password into the fields, and press Return (even if you cannot see the rest of the login window).
Additional Information
This issue will not occur if the display is not sleeping when the account is logged out. Use the steps below to confirm that the account is not configured to log out automatically while the display is sleeping:
1. Open System Preferences > Security & Privacy > General. Click the padlock to unlock the preference pane and enter your admin password. Click the Advanced button at the bottom, then see if the option "Log out after N minutes of inactivity" (where N is the number of minutes) is enabled.
2. Open System Preferences > Energy Saver and configure Display Sleep to occur after the account is logged out, by dragging the slider to a number of minutes that is greater than N was set to in the previous step.
Important: If automatic log out is not needed, disable "Log out after Nminutes of inactivity" in System Preferences > Security & Privacy > General. This will also prevent the issue.
http://support.apple.com/kb/TS4135?viewlocale=en_US

Windows Media Player does not recognize new downloaded songs

I have a Pavilion a4310f Prod Nr: AY014AA-ABA running Win 7 Home Premium 64 bit.
I just discovered that Windows Media Player does not recognize songs I recently downloaded from the Wal-Mart Music Download Site. The songs can be seen in the Music Library in a folder named "Downloads" and I can open each song and it will play when double clicked. The problem is that I can not create a playlist containing the new songs and burn a copy of the playlist because the songs are not listed in the Media Player library no matter hot it is sorted (Artist, Album, Genre, etc).
Any help/suggestions would be greatly appreciated.
Mitch
This question was solved.
View Solution.

You might also want to consider moving the songs to my Music or the folder you have WMP set as your Music folder. You can find/change that folder in WMP by going to File ---> Manage Libraries
Launch WMP ----> Tools ----> Options --->Privacy and be sure that the Display information from the internet box is checked.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Windows 8.1 does not recognize

My Windows Surface Pro does not recognize our 6th Generation iPod Nano

Hi kathyt8952 ,
Would you please share us more details of the issue ?
Have you checked the driver issue from the device manager ?Have you tried to connect the device from another USB port to have a check ?
We can take the following steps to have a check .
1.Open "run" from the start menu, and run "services.msc".
2.Search "Apple Mobile Device".
3.On "status" column right click and then click on "Properties"
4.In the "general" tab find the "startup type" drop-down arrow menu and make sure "automatic" is selected.
5.Also in the general tab check the "service status". If it does not say "started" then click the start button.
6.At the bottom of the properties window click "apply".
If the issue persists, we can refer to the following link to have a troubleshoot :
iPhone, iPad, or iPod not recognized in iTunes for Windows
https://support.apple.com/en-us/HT204095
We may also need to ask for help from the Apple Forum .They may have some good advices for you .
NOTE: This response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you. Microsoft does not control these sites and has not tested any software or information found on these sites.
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Windows 8.1 does not recognize my iphone.

windows 8.1 does not recognize my iphone.

Hi kathyt8952 ,
Would you please share us more details of the issue ?
Have you checked the driver issue from the device manager ?Have you tried to connect the device from another USB port to have a check ?
We can take the following steps to have a check .
1.Open "run" from the start menu, and run "services.msc".
2.Search "Apple Mobile Device".
3.On "status" column right click and then click on "Properties"
4.In the "general" tab find the "startup type" drop-down arrow menu and make sure "automatic" is selected.
5.Also in the general tab check the "service status". If it does not say "started" then click the start button.
6.At the bottom of the properties window click "apply".
If the issue persists, we can refer to the following link to have a troubleshoot :
iPhone, iPad, or iPod not recognized in iTunes for Windows
https://support.apple.com/en-us/HT204095
We may also need to ask for help from the Apple Forum .They may have some good advices for you .
NOTE: This response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you. Microsoft does not control these sites and has not tested any software or information found on these sites.
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Windows Security Suite does not recognize Verizon Internet Security Suite

Windows Secuity Suite does not recognize that the Verizon Internet Security suite on one of my PC's is running and keeps popping up aWindows Security Alert. The Firewall is enabled within Verizon Internet Security suite.
My other PC's don't have this issue.
All PC's are running Windows Vista Home Premium.
Any ideas?
Cheers,
Mark

well that error message is saying that Windows security center no longer supports the way that the VISS is reporting. Which means that even though VISS is working and it is even reporting its status to WSC. WSC doesnt recognize it anymore. Likely one of the windows updates made the change. I can see the fight comming now. Verizon is going to say. Its working and if the other program doesnt support it, too bad. And windows is going to say the same thing in reverse. My guess would be that it will probably stay that way unless Verizon or Microsoft get enough complaints to make a change in the recognition system.
But the good news is that VISS is running and protecting you. The WSC just doesnt "speak the same language" anymore and cant understand the message from VISS saying "I'm up and running"
====================================================================================
Error exists between keyboard and chair.

I had to replace my Iphone 5c with a new one. Now, my windows 7 pc does not recognize my iphone. Reinstalled itunes. Apple mobile device is running. I did whatever I could find on the internet still no luck. Any suggestions? Thnx

I had to replace my Iphone 5c with a new one. Now, my windows 7 pc does not recognize my iphone. Reinstalled itunes. Apple mobile device is running. I did whatever I could find on the internet still no luck. Any suggestions? Thnx

You have done everything verbatim included with this link?
http://support.apple.com/kb/ts1538

Instant Client on 64-bit Windows 7: Driver does not appear in System DSN

Instant Client on 64-bit Windows 7: Driver does not appear in System DSN tab when creating a new Data source.
What I did so far:
I downloaded the basic and odbc zips for Window 64-bit.
Unzipped the basic zip.
Unzipped the odbc zip to the same directory.
Added the dir path to the System Environment Variable called Path.
Double-clicked on the odbc_install.exe to run it from Windows Explorer.
Then I tried to add the driver to create a new data source but it does not appear in the list of drivers.
From a cmd window, I navigated to the instant client directory and tried to run odbc_install again.
I got the message: Oracle ODBC Driver with same name already exists.
What am I missing?

hello, I did it like that you say,but the result also is "oracle odbc driver with same name already exists". I don't kown what can I do it ,Thank you!

Windows "Easy Connect" does not reply with the password / "Easy Connect is not Available"

Hello,
I have posted a related question some time ago, which was eventually resolved. However, after some time a problem with Easy Connect (used for MSRA) came back:
Whenever I arrive at the point in setting up a MSRA session where Easy Connect is needed, I get the reply: "Easy Connect is not Available". Here is an example of the problem:
Start MSRA
--> as expected, a window with "invite someone to help you" and " Help some who has invited you" appears
Select "invite someone to help you"
--> as expected, a window with "Who do you want to get help from" appears
Select "Invite someone to help you"
--> as expected, a windows with "How do you want to invite your trusted helper?" appears
Select "Use Easy Connect"
--> as expected, the temporary "Create invitation window / checking network capabilities" window appears
Next, I would expect this windows to close a new window to provide me with the Easy Connect password. However, instead I get the window "Easy Connect is not available".
I cannot continue. (I have screenshots so can repost with them if that would clarity my question)
Any suggestion how to resolve would be appreciated.
(Please do not reply with the 3 suggestions from the FAQ (both computers must run windows 7 / Access to internet is limited / your router does not support Easy Connect - doesn't help)
More background information and things I have tried:
The "Easy Connect is not available" window offers the "Tell me more about how to fix this problem" which I have tried, but those suggestions do not help
If I use the other MSRA option: "Help someone who has invited you" (this would be my typical use case), followed by "help someone new" and than select "Use Easy Connect", I also get the "Easy Connect is not available"
window instead of the expected option to enter the Easy Connect password. I believe this is that same problem.
This happed with both the 32 as well as the 64 MSRA versions
I'm using Window 7 Ultimate, 64 bit with all the latest updates
This desktop PC is wired to the internet via an Edimax gigabit switch, a Dlink DIR-855 wireless router and a fiber modem in bridge mode
The W7 desktop has a single active network connection only
I'm using Windows Firewall and Windows Security Essentials
Disabling the firewall on the PC did not help
Network discovery is enabled in Control Panel\All Control Panel Items\Network and Sharing Center\Advanced sharing settings (that’s UPnP – right?)
The Internet Connectivity Evaluation Tool does not seem to be available anymore from MSFT sites
Restarting "Peer Name Resolution Protocol" did not help
Restarting "Peer Networking Identity Manager Properties" did not help
Starting up with a "Clean Boot" (disabled all non-Microsoft services using MSConfig) did not help
I would also be interested to understand how I can check on the status of the "Easy Connect" service. Is this a service hosted somewhere, or??
Thanks!

Dear Andy,
Thanks a lot for your reply. Let me answer your questions:
Q: Could you use the other methods: save this invitation as a file and use e-mail to send invitation?
A: yes, that way I can establish a MSRA connection
Q: Have you disable other network connections, including disable all virtual network card?
A: if I check with ‘Device Manager/Network Adapters’ (or Control Panel/Network and Internet/Network Connections) I see two network adapters (my Asus motherboard has two network connectors). Both are available, but only one is used. I have
disabled one. Unfortunately, this does not solve the problem. I will leave it disable for now.
Q: To find detailed information about this issue, please locate to event view and find the logs about remote assistance.
A: I have to admit that the Event Viewer is unfamiliar territory for me. So, I’m not sure where and what to look for. However, as suggested, I found "Event Viewer (local)/Applications and Services Logs/Microsoft/Windows/Remote assistance/Operational".
Each time, I attempt to use MSRA/Easy Connect, it seems two entries are added. As I cannot seem to upload files with this post, here are just the two entries:
“Diagnosis Repro Attempt resulted in a failure.”
“Remote Assistance troubleshooting has confirmed the problem: Remote Assistance Easy Connect isn't available.”
If you need more details, please suggest what to forward or check. I'm eager to find a solution!
W.

My computer has been acting weird lately. Shuts itself off, the mouse goes off in all angles, does not go into sleep mode sometimes and instead shows on a gray screen definitions of words in 3" letters! Do I have a virus?

My computer has been acting weird lately. Shuts itself off, the mouse goes off in all directions, does not go into sleep mode sometimes, instead shows a gray screen with word definitions in large 3" letters that continuosly flows across the screen. Do I have a virus?

Doesn't really sound like a virus.
See if the Disk is issuing any S.M.A.R.T errors in Disk Utility...
http://support.apple.com/kb/PH7029
How many of these you can answer...
Open Activity Monitor in Applications>Utilities, select All Processes & sort on CPU%, any indications there?
How much RAM & free space do you have also, click on the Memory & Disk Usage Tabs.
Open Console in Utilities & see if there are any clues or repeating messages when this happens.
In the Memory tab, are there a lot of Pageouts?

MacBook Pro does not go to sleep when power cord is connected

Hi Experts,
I have recently discovered that my MacBook Pro (2009) with OSX Lion does not go to sleep when the power cord is connected. It does not matter if I close the lid or select sleep from the Apple menu. All that happens is that the screen is powered off, the SIL is solid and I can hear the HDD/fan. I have not changed any of my power settings recently and it has not been a problem previously. If I disconnect the power cord the MB goes to sleep as supposed to (the SIL led starts flashing).
Doing some research I have found other users with somewhat the same issues when VMWare Fusion is installed. I have done some further testing and it seems that if I disable the virtual machine's Network Adapter and quit VMWare Fusion the MB goes into sleeping mode when the lid is closed even with the power cord connected. Enabling the Network Adapter again prevents the MB to go into sleeping mode when the power cord is connected. This even applies when the VMWare application is shutted down.
My guess is that the Network Adapter somehow prevents the MB to go into sleeping mode. The workaround is of course toggling the Network Adapter on and off but the virtual machine has to be running in order to do so. Not being that familiar with network settings on a Mac is there any other way to get around the problem?
Thanks in advance :-)

To anyone,
I have turned internet sharing off but the Ethernet box remains checked. If I uncheck the Ethernet box, the Internet Sharing bubble turns red, however when I close System Preferences and re-open, the box is automatically checked although Internet Sharing is off. Because of this my Macbook Pro will not sleep properly.
All other sharing items are turned off. Only Internet Sharing continues to automatically show Ethernet as active from a Wi-Fi connection.
Any advice?

How do i share itunes music? I have a Mac and she is on Windows. She does not have an iTunes or iCloud ID

How do i share itunes music? I have a Mac and she is on Windows. She does not have an iTunes or iCloud ID.

You could install iTunes on her PC, then sign in using your ID and activate her computer (iTunes menu bar: Store Authorize This Computer) in order to download your previous purchased media files.

Windows 2008 R2 does not work on Sunfire X4170

Hi, I recently bought a used X4170 server and have a weird problem. Windows 2008 R2 does not work, but 2012 does. I tried RTM version and a version with SP1. The problem is this:
After installing, I set the password and windows just displays a blank desktop, sometimes it boots but freezes soon after - the mouse cursor moved but nothing else works.
Booting in Safe Mode works and Windows do not freeze. The Event Log contains lots and lots (about 20 per second) of these entries:
Log Name:
System
Source:
Microsoft-Windows-WHEA-Logger
Date:
6/21/2014 12:24:59 AM
Event ID:
17
Task Category: None
Level:
Warning
Keywords:
User:
LOCAL SERVICE
Computer:
WIN-SOGS2TPM334
Description:
A corrected hardware error has occurred.
Component: PCI Express Root Port
Error Source: Advanced Error Reporting (PCI Express)
Bus:Device:Function: 0x0:0x0:0x0
Vendor ID:Device ID: 0x8086:0x3406
Class Code: 0x30000
I have tried updating the driver for this device (downloaded from Intel), no difference. Is there a way to make Windows 2008 R2 work on this server?

Hello
Thank you for the update.
Please refer the below Knowledge document related to this issue:
Windows BSOD WHEA_UNCORRECTABLE_ERROR(124) & correctable WHEA events when disabling network ports on X4170M2/X4270M2 (Doc ID 1576683.1)
However above document talks about X4170M2, I would suggest you to follow and if issue persist, please open Service Request with Oracle to diagnose further.
Best Regards
Bhavyesh

Windows 8.1 does not go to sleep reliably anymore

Similar Messages

Maybe you are looking for